

Page 1 of 15

Text on page 2
Operator’s Manual
GoCrease
TM
SEMI
Page 2 of 15

Text on page 3
Content
- Introduction……………………………………………………………………………………………………..….3
Safety Warning ................................................................................................ 3
General Work Safety and Health Protection ................................................... 3
- Technical Parameters …………………………………………………………………………………………5
- Machine Description …………………………………………………………………………………………6
- Machine Installation …………………………………………………………………………………………9
- Setting Machine Using Touch Screen ………………………………………………………………..10
Language selection ........................................................................................ 10
Setting Number of Segments ........................................................................ 10
Setting Position of Segments ........................................................................ 11
Special Types of Folds ................................................................................... 11
Saving and Loading of Program ..................................................................... 12
Working Cycle ............................................................................................... 13
Manual Control ............................................................................................. 13
Service menu ................................................................................................. 14
- The Most Common Faults (Troubleshooting) ……………………………………………………14
- Machine Disposal ……………………………………………………………………………………………..15
Page 3 of 15

Text on page 4
- INTRODUCTION
We are presenting you with Operating Instructions that contain machine technical data and instructions necessary for correct setting, machine start-up, operation and maintenance. Instructions are intended for machine operation as well as for service engineers. People manipulating, installing and operating the machine should familiarise themselves with the instructions before they start. The machine construction complies with the Directive 98/37/EC of the European Parliament and of the Council. If all the instructions in this document are respected, you will be satisfied with precision and performance of the machine. We can assure you the machine received maximum care. Thoroughness of control ensures machine precision within the scope of the acceptance standards applicable for this machine. We believe these Operating Instructions will be a valuable guide for you.
- SAFETY RISKS
When using GoCrease 4000, all safety rules and procedures as well as all warnings regarding work safety and health protection listed in this document must be observed. Factors increasing risk:
- Rotating pulleys and moving belts
- Voltage
- Noise made during processing
- Moving parts of the machine and equipment
- Sharp edges created during processing
- Dust created during processing
General Work Safety and Health Protection
This section provides the user with basic information about work safety and health protection of an operator and all other people who come into contact with the machine. If the GoCrease 4000 is used correctly, it is a very safe machine. However, if used incorrectly, it can be dangerous. When operating the machine, the operator is responsible for their own personal safety. The manufacturer is not responsible for any injury to a person or damage to the machine caused by use or operation that is not in compliance with the Operating Instructions. The owner of the machine is responsible for the machine being operated, maintained and serviced only by qualified people. The machine design is in compliance with international standards and regulations for construction of machine tools. For the machines exported to the European Economic Area (EEA), the customer will obtain "Declaration of Conformity" together with the accompanying technical documentation for the machine - Operating Instructions. The machine also has the CE marking. The CE marking on the machinery signifies that the product complies with the technical requirements specified in all the legal regulations that apply to the machinery and that require or allow this marking. This marking also signifies that a specified procedure was followed during the assessment of the stated conformity.
Page 4 of 15

Text on page 5
With the document “Declaration of Conformity” the manufacturer certifies that the given machinery complies with the requirements of the Directive 98/37/ES of the European Parliament and of the Council and the harmonised technical standards. Directive 98/37/ES of the European Parliament and of the Council is a document defining the generally applicable basic requirements of the health protection and safety for the machinery operated by a user in the EEA. The Directive 98/37/ES of the European Parliament and of the Council does not apply to the machinery exported to the countries outside the EEA. The customer will receive the accompanying technical documentation for the machine – Operating Instructions. The manufacturer hereby asks the user to ensure comprehensive safety as directed by the relevant legal proceedings, standards and regulations, the Operating Instructions and other, by training the workers consistently. The machine is intended for work in automatic cycles. The machine operator monitors the process and the operating mode of the machine. Also replaces material with the new one and checks the measurements.
- WARNINGS
Only sheets of the size listed in the parameters can be creased and perforated in the creasing and perforating machine.
- It is not advised to crease and perforate foils, sheet metal or other similar materials.
- Do not use the machine when the electric cord is damaged.
- Do not plug the machine into other voltage than indicated on producer’s identification plate.
- Read all instructions before using the machine.
- It is not suitable for children to be near the machine.
- Do not put fingers or hands into the machine when the electric cord is plugged in.
- When the machine is jammed, it is necessary to unplug the machine first and then troubleshoot.
- When replacing a faulty electrical component, do not use a different type of component or different capacity component. When replacing a component, the electric cord must be unplugged. l) Covers can be only dismounted by a trained technician when the machine is unplugged.
Page 5 of 15

Text on page 6
- TECHNICAL PARAMETERS
Recommended paper grammage - creasing 80 - 400 g/m² Recommended paper grammage perforation 80 - 250 g/m²
CITO 1,0 mm - paper thickness < 0.007” (mostly 80 - 150 gsm) CITO 1,4 mm - paper thickness 0.007” – 0.01” (mostly 160 - 250 gsm) iron channel - paper thickness 0.01” – 0.02” (mostly 250 - 400 g/m²)
Max. number of creases per sheet
Min./Max. distance of creases
Min. distance of crease from edge of the sheet
1500 LTR sheets/ hr (with one crease)
Predefined types of fold
1/2, 1/3, 1/4, book cover
net 115.8 lbs., gross 124.6 lbs.
120 V, 60 Hz
- Note: It is necessary to respect recommended width of creasing channel for different paper thickness. If inappropriate width of crease is used (usually narrow creasing channel for thick paper) inaccuracies in position of crease may appear, crease will be placed in different distance than what is set on display. If thick paper is used in combination with narrow crease, the result is that the paper is pressed into the creasing channel, the rollers start to slip trying to release the paper. Use wider crease in such case.
Page 6 of 15

Text on page 7
- MACHINE DESCRIPTION
the machine GoCrease SEMI magnetic side guide magnetic strip perforating knife creasing knife (fitted on the machine) lower creasing/perforating tool (fitted on the machine) supply cable hexagonal key
15 – 0.2” hexagonal screw 16 – Locking screw 17 – Pressing mechanism 18 – Adjusting screw
1 – Feeding table 2 – Delivery table 3 – Fixed T-square 4 – Left side guide 5 – Magnetic strip 6 – Display 7 – Control light 8 – STOP button 9 – Square bar 10 – Upper cover 11 – Magnetic stop 12 – Power supply switch 13 – Clamp A/B 14 – Ram
Page 7 of 15

Text on page 8
Electric creasing and perforating machine is suited for final processing of graphic materials up to 17.7” width. Creasing enables easy folding of the paper. Knife change and turning of the square bar (9) allows to make perforation. Waste-less perforation allows easy separation of the paper.
Page 8 of 15

Text on page 9
- MACHINE INSTALLATION
After unpacking the machine has to be put on a solid area, the delivery table is put on (2). After the machine has been plugged into the power outlet, it is ready to operate and the display is alight (6). When the upper cover (10) is lifted up the machine is automatically turned off and the control light (7) turns red.
Machine is adjusted for creasing by manufacturer. To start with perforating, it is necessary to change the knife (in the packaging included). First, the machine has to be unplugged and the upper cover (10) lifted up. Dismount 2 locking screws (16) located on the joist of the hinged pressing mechanism (17). Lift off the hinged mechanism and fix it in the upper position by locking screws inserted into the sideboard. Dismount 5 hexagonal screws (15) and the clamp (13A,B). For perforation, it is necessary to set the square bar (9) face up by flat side without creasing channels. Do not tighten the knife completely, carry out a control upstroke to make sure that the upper edge touches the slide and finally tighten the screws (15). Carry out the assembly of the pressing mechanism (17) which is placed in the original position.
The ram (14) with perforating or creasing tool can be moved down by the help of both adjusting screws (18).The screws should be loosened in gradually by 1/6 th revolution to the left approx. 60˚(the bar moves down) and then it has to be fastened by a nut. After each 60˚ turn it is necessary to check whether perforating (creasing) quality is sufficient. When the ram is set-up correctly (14) it is not needed to re-adjust it with each change of function (perforating, creasing).
Page 9 of 15

Text on page 10
- SETTING MACHINE USING TOUCH SCREEN
After the power supply switch has been turned on, the display shows the basic menu (fig.1)
Fig. 1: The Main screen
There is a hidden icon in the left upper corner. If you press this space a language menu comes up (fig.2).
Fig. 2: Language selection
Press an icon with required language. Then the display shows the basic menu in chosen language. Counter reset (finished) To reset the meter you should proceed as follows. Press the blue figure “pcs”, which is the number of papers that have been processed last. This brings up a figure keyboard. Press number “0” and confirm it by pressing “ENTER”. That takes you back to the previous menu and the meter shows zero.
Setting Number of Segments
Pressing the numeric icon under the “Number of creases" displays the numeric keypad. By pressing the relevant digit, the number of creases/perforations (segments) is set. The program enables setting of up to 15 segments. The selection of number of segments is ended by pressing the "Enter" key. The number of segments is now set.
Page 10 of 15

Text on page 11
Fig. 3: Setting screen
Setting Position of Segments
The position of the first segment is set as the distance from the edge of the sheet. The position of each following segment is defined as its distance from the previous segment. The "no. +" and "no. -" serve for the choice of required segment. Choose the segment number 1 and then press the numeric icon under the word "length". A numeric keypad is now displayed. Use the numeric keypad to set the distance from the edge of the sheet and press "Enter". The position of the first segment is set. Choose the segment number 2 using the "no. +" key and then press the numeric icon under the word "length" again. Use the numeric keypad to set the distance from the first segment and press "Enter". The second segment is set. Set all the remaining segments the same way. When all the segments are set, press the "Return" icon to go back to the main menu. The machine is now ready to process the task.
Special Types of Folds
By pressing “>>>” icon in Setting screen we enter to screen where most common types of fold are displayed (fig. 4). To achieve most common folds it is necessary to crease in certain distances like 1/2, 1/3 or 1/4 of the paper. By pressing appropriate icon we can easily achieve one of the most-used folds. First, it is necessary to prepare the required sheet the same way as for the processing. Then press the “1/2” icon (other fold types accordingly), followed by “<<<”, “Return” and “Start” icons. On main screen appears symbol of appropriate icon (1/2, 1/3, etc.). One sheet goes through the machine, its length is measured and 1/2 of the length is calculated. The screen changes to the Setting screen (fig. 3). The calculated length of the 1/2 is displayed in the “length” box. Then return to the main screen and press the “Start” icon. We recommend to process only one sheet and check the position of the 1/2, whether the distance was measured correctly. If the crease is not in precisely in the required distance, return to the Setting screen and correct the distance manually. All other folds work the same way.
Page 11 of 15

Text on page 12
Fig. 4: Most common types of fold
Amongst these types of fold there is one very special function called book cover. The machine GoCrease SEMI is excellent for making professional book and brochure covers. Book cover is defined by 4 creases made in the middle of the sheet with fixed distances 0.23” between the first and second crease and third and fourth crease. The distance between second and third crease is optional depending on thickness of book. This dimension is defined by “length” icon below book cover icon.
Saving and Loading of Program
The software allows saving up to 5 different programs. The number and position of the segments is set according to the procedure described in Section 7.3. As soon as the last step of setting (the required number of segments and their position) is done, the program can be saved. On the main screen press the number in the right side of the screen showing program number. The menu for saving and loading of a program (fig. 5) appears.
Fig. 5: Saving and loading program
Choose the number for numbering the program using the keys "prg +" and "prg -". Press the “Save" icon. Go back to the main menu by pressing "Return". The program is saved.
Page 12 of 15

Text on page 13
Load the program as follows: On the main screen press the number in the right side of the screen showing program number. Choose the number of the program you want to load using the keys "prg +" and "prg -". Press the "Load" icon. Go back to the main menu by pressing "Return". The machine is ready to operate according to the loaded program.
Warning: The screen displays the number of the last program saved or loaded. For more effective work the operator can change the program without saving it. In such case, the number of the last program saved or loaded is still displayed, but the machine operates according to the operator’s last setting, even though this setting has not been saved. If the machine is turned off and then turned on again by the electric switch, the machine operates according to the program displayed on the screen. The last unsaved setting is deleted.
You can either choose a preset program or create your setting. Adjust the movable left side guide (4) on the feeding table according to the paper size. Between side guides either remove or add magnetic strips (5) which prevent paper from deflection. Set the distance of the magnetic stop (11) on a delivery table according to the paper size. Press the "Start" icon on the screen (fig. 1). The machine starts up and the working cycle screen is displayed (fig. 6). There are a "Stop" icon and information about the number of processed sheets displayed on the screen.
Fig. 6: Working cycle screen
Start feeding the machine with the paper. It is very important to do this accurately. When the machine is creasing or perforating the red diode on the main panel is on. You can put more paper in the machine after the red light changes into green again. The machine can be turned off by pressing the “Stop” button on the display. In case of emergency you can use a red “STOP” button placed on the main panel.
When changing the tools it is necessary to carry out a testing upstroke (turn) to make sure that both tools are parallel, and also to make sure that either creasing or perforating tool is leaned against the slide. Do this by pressing the “Move” icon and the following menu comes up – “Manual control” (fig. 7).
Page 13 of 15

Text on page 14
Fig. 7: Manual control
After activating the “1 turn“ icon the control upstroke is carried out. In case the crease depth is not the same on the both sides of the paper or perforation does not result in direct separation of the paper, adjust the ram (14) with a perforation knife. This can be done using the adjusting screws (18). It is necessary to loosen the screws gradually by 1/6 of the turn (60°) to the left (slide goes down), and then secure it with a nut. You should check the quality of perforation after each turn (60°). If the quality is suitable, you can stop. After the machine is adjusted for perforation, it is adjusted for creasing as well. Icons “Forward“ and “Backward“ are used to release stuck pieces of paper from the machine. To go back to the main menu, press “Return“.
There is a hidden icon in the right upper corner. This icon is there for a service technician trained by MBM Corporation. To access this icon you need to enter a password (fig. 8).
Fig. 8: Service screen
8. THE MOST COMMON FAULTS (TROUBLESHOOTING)
a) Upstroke stoppage: If this problem occurs during adjusting and checking the upstroke of the ram (14), it is necessary to turn the adjusting screws (18) to the right by two turns (the ram goes up). When the upstroke cycle is terminated, then the red diode is on. After the machine is turned back on the upstroke process should finish. It is necessary to readjust the ram (14).
b) Paper jam: When the paper gets jammed or damaged, it is necessary to turn the machine off immediately (press the STOP button 8). After the machine has been stopped
Page 14 of 15

Text on page 15
tap on the MOVE icon. Before removing the paper, it is necessary to carry out an upstroke (1 turn icon). Use button Backward or Forward depending on situation.
c) Crease is in incorrect position compared to values set on display It is necessary to respect recommended width of creasing channel for different paper thickness. If using inappropriate width of crease (usually narrow creasing channel for thick paper) inaccuracies in position of crease may appear, crease will be placed in different distance than what is set on display. If using thick paper in combination with narrow crease, the result is that the paper is pressed into the creasing channel, the rollers start to slip trying to release the paper. Use wider crease in such case. Look for correct crease width in chapter 2, c.
9. MACHINE DISPOSAL
When the lifetime period is over, do not dispose the machine in common waste. The machine must be disassembled and metallic, non-metallic, plastic, rubber and electronic parts sorted. These parts are disposed of in the relevant points of recycling. Some parts of the machine can contain dangerous substances that are harmful to the environment and health.
Page 15 of 15 ยท End of manual
Quick start
- Place the machine: Put the machine on a solid area and put the delivery table on.
- Power on: Plug the machine into the power outlet. The display lights up and the machine is ready. Keep the upper cover down, because lifting it turns the machine off.
- Load a program: On the main screen, press the program number. Pick a number with "prg +" and "prg -", press "Load", then press "Return". You can also create your own setting.
- Set the side guide: Adjust the movable left side guide on the feeding table to the paper size. Add or remove magnetic strips between the guides to keep the paper from deflecting.
- Set the delivery stop: Set the distance of the magnetic stop on the delivery table to the paper size.
- Start the machine: Press the "Start" icon. The working cycle screen shows the number of processed sheets.
- Feed the paper: Feed paper accurately. The red light is on while the machine works. Add more paper when it turns green. Press "Stop" to stop, or the red STOP button in an emergency.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Upstroke stoppage while adjusting the ram | The upstroke of the ram stopped during adjusting and checking. | Turn the adjusting screws to the right by two turns so the ram goes up. After the upstroke cycle ends, the red diode is on. Turn the machine back on, let the upstroke finish, then readjust the ram. Page 14 |
| Paper jam | Paper is jammed or damaged in the machine. | Turn the machine off at once with the STOP button and unplug it before troubleshooting. Use the "Forward" and "Backward" icons in Manual control to release stuck pieces of paper. Page 14 |
| Crease depth is not the same on both sides, or perforation does not separate the paper | The ram with the perforation knife needs adjusting. | Loosen the adjusting screws gradually, 1/6 of a turn (60 degrees) to the left, then secure with a nut. Check the perforation after each turn and stop when it is good. Page 14 |
| Tools do not run parallel after a tool change | Tools were changed and have not been tested. | Run a test upstroke. Press "Move", then the "1 turn" icon. Check that both tools are parallel and that the creasing or perforating tool leans against the slide. Page 13 |
| Machine turns off and the control light turns red | The upper cover is lifted. The machine turns off automatically when it is lifted. | Close the upper cover. Page 9 |
| Machine runs a setting that is not the program shown on screen | A change was made without saving it. The screen still shows the last program saved or loaded. | Load the program you want with the "Load" icon. An unsaved setting is deleted when the machine is turned off and on again. Page 13 |
Frequently asked questions
How do I load a saved program?
Press the program number on the main screen, choose a number with "prg +" and "prg -", and press "Load". Then press "Return" to go back to the main menu. See page 13.
How do I switch from creasing to perforating?
The machine is set for creasing at the factory. To perforate, change the knife to the one included in the packaging. Unplug the machine and lift the upper cover first. See page 9.
Can I crease or perforate foil or sheet metal?
It is not advised to crease or perforate foils, sheet metal or similar materials. See page 5.
When can I add more paper?
The red light is on while the machine creases or perforates. Add paper after the light turns green again. See page 13.
How do I stop the machine?
Press the "Stop" button on the display. In an emergency, use the red STOP button on the main panel. See page 13.
