

Page 1 of 2

Text on page 2
≥4205 manual cutter
“SCS” (Safety Cutting System) features: hinged, transparent safety guard on front table (locks automatically while cutting); transparent safety cover on rear table; safety catch (locks blade lever in up position); blade change from front without removing machine covers; blade changing device covers cutting edge of blade; blade depth adjustment from outside of machine; cutting stick can be turned or changed from outside of machine ❙ compact size ❙ Solingen steel blade ❙ solid steel blade carrier and adjustable blade guides ❙ extra large cut lever requires minimal effort ❙ patented, lever-activated, fast-action clamp ❙ side guide with measuring scale ❙ spindle-guided back gauge with calibrated crank and measuring scale ❙ all-metal construction ❙ optional stand (shown)
The hinged front safety guard locks in the lowered position during cutting process.
easy cutting stick change
Dimensions (DxWxH): 32 3 ⁄ 4 x 34 3 ⁄ 4 x 15 3 ⁄ 4 inches (43 H with stand), Shipping weight: 115 lbs. (141 with stand).
Cutting sticks can be turned or changed from outside of machine.
back gauge and side guide
Accurate, cast aluminum back gauge and side guide allow precise paper alignment.
Cutting length behind blade
Table length 9" in front of blade
Dealer:
3134 Industry Drive North Charleston, South Carolina 29418 800-223-2508, fax: 843-552-2974 www.mbmcorp.com
1675 Sismet Road, unit 4 Mississauga, Ontario L4W 4K8 800-387-2528, fax: 905-840-1114 www.ideal-mbm.com
All technical data is approximate and subject to change. © MBM Corporation, 2/2008.
Page 2 of 2 · End of manual
Quick start
- Set it up: the cutter is compact. Its dimensions (DxWxH) are 32 3/4 x 34 3/4 x 15 3/4 inches, or 43" high with the optional stand.
- Set the side guide: use the side guide and its measuring scale to line the paper up. The cast aluminum back gauge and side guide allow precise alignment.
- Set the back gauge: use the spindle-guided back gauge with its calibrated crank and measuring scale. The table is 9" long in front of the blade.
- Clamp the stack: use the lever-activated, fast-action clamp.
- Lower the guard: the hinged front safety guard locks in the lowered position during the cut.
- Cut: pull the extra large cut lever, which takes minimal effort.
- Service from outside: the blade changes from the front, blade depth adjusts from outside the machine, and the cutting stick can be turned or changed from outside.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Cuts are not square to the paper edge | The paper is not aligned against the guides | Align the stack with the cast aluminum back gauge and side guide, and read the measuring scales. Page 2 |
| The blade is dull | Normal wear on the Solingen steel blade | Change the blade from the front without removing machine covers. The blade changing device covers the cutting edge. Page 2 |
| The blade cuts too shallow or too deep | The blade depth needs adjusting | Adjust the blade depth from the outside of the machine. Page 2 |
| The cutting stick is worn | The blade has cut into the stick | Turn or change the cutting stick from outside the machine. Page 2 |
| The stack shifts during the cut | The stack is not held firmly | Use the patented lever-activated, fast-action clamp to hold the stack. Page 2 |
| The cut lever will not come down | The safety catch is holding the blade lever in the up position | Release the safety catch, which locks the blade lever up, before you cut. Page 2 |
Frequently asked questions
What safety features does this cutter have?
The SCS system includes a hinged transparent front safety guard that locks automatically while cutting, a transparent rear table cover, a safety catch that locks the blade lever up, and a blade changing device that covers the cutting edge. See page 2.
Can the blade and cutting stick be changed without removing covers?
Yes. The blade is changed from the front without removing machine covers, blade depth is adjusted from outside, and the cutting stick can be turned or changed from outside the machine. See page 2.
How big and heavy is it?
32 3/4 x 34 3/4 x 15 3/4 inches (D x W x H), or 43" high with the optional stand. Shipping weight is 115 lbs, or 141 lbs with stand. See page 2.
How much table is in front of the blade?
The table length in front of the blade is 9". See page 2.
