MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 1

Page 1 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 2

Page 2 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 3
Text on page 3
  • Safety precautions •

IDEAL 4860 • IDEAL 6660

FIN

Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein. Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available. Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine, et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation et les consignes de sécurité doivent toujours être disponibles. Les instructions d'utilisation et les consi. Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en de veiligheids-voorschriften moeten altijd binnen handbereik zijn. Per favore legga questo manuale di istruzione prima di mettere in funzione il distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono essere sempre disponibili. Le recomendamos lea las instrucciones antes de poner en funcionamiento esta máquina y cumpla las normas de seguridad. Las instrucciones de servicio y seguridad deben estar siempre disponibles. Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig. Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen ! Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla. Lees gjennom denne bruksannvisningen før De tar i bruk maskinen Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen må alltid være tilgjengelig. Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być zawsze dostępne.

RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä óñòàíîâêîé

A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie. TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý her zaman kullanýma hazýr olmalýdýr. DK Før installation af maskinen bedes De venligst læse brugervejledningen og være opmærksom på sikkerhedsanvisningerne. Brugervejledningen skal altid være tilgængelig. CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní upozornění. Návod k obsluze musí být vždy dostupný. P Por favor leiam o manual de instruções antes de colocar a máquina em operação e vejam as precauções de segurança. As instruções de operação deverão estar sempre disponíveis. GR ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ. ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ. SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila preden zaženete naparavo. Navodila naj bodo vedno pri roki. SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na dostupnom mieste. EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige ohutusnõudeid. Kasutusjuhend peab alati käepärast olema. CHI

UAE

Page 3 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 4
Text on page 4
  • Safety precautions •

D Keine Bedienung durch Kinder! GB Children must not operate the machine! F Pas d‘utilisation par un enfant! NL Geen bediening door kinderen! Non lasciare utilizzare il tagliacarte a bambini! E No dejar que la utilicen los niños! S Installera maskinen utom räckhåll för barn! FIN Asentakaa laite lasten ulottumattomiin ! N Installer maskinen utenfor rekkevidde for barn! PL Dzieciom nie wolno obsługiwać urządzenia ! RUS Íå äîïóñêàéòå äåòåé ê ïîëüçîâàíèþ àïïàðàòîì! H Gyerekek a gépet nem kezelhetik TR Makinayý Çocuklar Kullanmamalýdýr. DK Må kun betjenes af voksne CZ Stroj nesmí být obsluhován dětmi! P As crianças não devem trabalhar com a máquina! GR ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ. SLO Otroci ne smejo uporabljati naprave SK So strojom nesmú pracovat deti! EST Lapsed ei tohi masinat kasutada! CHI UAE

D Nicht unter das Messer fassen! GB Do not reach beneath the blade! F Ne pas passer les mains sous la lame! NL Niet met de handen onder het mes komen! Non toccare la lama nella parte inferiore! E ¡No tocar debajo de la cuchilla! S Sträck inte in handen under kniven! FIN Älä laita kättäsi terän alle ! N Plasser aldri hender ol. under kniven ! PL Nie wkładać rąk pod noże! RUS Èçáåãàéòå ïîïàäàíèÿ ðóê ïîä ëåçâèå! H Ne nyúljon a kés alá! TR Elinizi býçaðýn altýna sokmayýnýz! DK Stik ikke hænderne ind under knivbladet! CZ Nesahejte pod ostří nože! P Não tocar na parte inferior da faca! GR ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ! SLO Ne segajte z roko pod rezilo! SK Nevkladajte ruky pod nôž! EST Ärge pange kätt tera alla! CHI UAE

Page 4 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 5
Text on page 5
  • Safety precautions •

IDEAL 4860 • IDEAL 6660

Messer nie lose liegen lassen! Messer nur mit Messerwechselvorrichtung oder im Messertransportkasten befördern! (siehe Seite 29 und 31). Warnung! Verletzungsgefahr! GB Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 29 and 31). Danger! Risk of injury! F Ne jamais laisser la lame sans protections ! Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf. page 29 et 31), ou transportée dans son étui en bois ! Danger! Risques de coupures ! NL Laat nooit de messen alleen achter. Transporteer de messen niet zonder de houten bescherming (zie pagina 29 en 31). Waarschuwing! Opgelet voor ongevallen! Non lasciare mai la lama incustodita. Non rimuovere o trasportare la lama senza protezione. (Vedi pagina 29 e 31). Attenzione! Rischio di infortunio! E ¡No quitar la cuchilla sin prestar atención. No desmontar no transportar la cuchilla sin protección! (vérase pág. 29 y 31) ¡Advertencia! ¡Peligro de hacerse daño! S Lämna aldrig maskinen obemannad. Ta inte ur eller transportera kniven utan skydd. (se sid 29 och 31). Skaderisk! FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta terää ilman suojaa ! (katso sivu 29 ja 31 Loukkaantumisen vaara ! N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller transporter den uten beskyttelse (Se side 29 og 31) FARE ! Muligheter for skade ! PL Nigdy nie pozostawiać noży bez nadzoru. Nie wyciągać lub transportować noży bez osłon! (zobacz strona 29 i 31). Ryzyko skaleczenia sie! RUS Íå îñòàâëÿéòå îòêðûòîå ëåçâèå áåç ïðèñìîòðà! Íå

Soha ne hagyja a kést őrizetlenül! Ne vegye ki vagy ne szállítsa a kést védőtok nélkül! (Lásd 29. és 31. oldal) Veszély! Sérülésveszély! Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz! Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya taþýmayýnýz! (Sayfa 29 ve 31’e bakýnýz) Dikkat! Yaralanma riski!

Page 5 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 6
Text on page 6
  • Safety precautions •

Knivbladet må aldrig efterlades uden opsyn. Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 29 og 31) FARE! Risiko for legemlig beskadigelse. CZ Nikdy nenechávejte nůž bez krytu. Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 29 a 31) Nebezpecí! Riskujete zranení P Deixar a faca sempre em local seguro! Não retirar ou transportar a faca sem protecção! (Ver pág. 29 e 31) Perigo! Risco de dano! GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ! ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 29 & 31) ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ ! SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte rezilo brez zaščite. ( glej stran 29 in 31). Pozor! Nevarnost poškodbe. SK Nenechávajte nôž nechránený (nezabezpecený)! Nevyberajte alebo netransportujte nôž bez ochrany (vid s. 29 a 31) ! Riziko úrazu ! EST Ärge jätke lõiketera kunagi järelevalveta! Ärge pikendage ega teisaldage tera kaitseseadmeteta! (Vt lk 29 ja 31) Oht! Vigastuste oht! CHI

UAE

Page 6 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 7
Text on page 7
  • Safety precautions •

IDEAL 4860 • IDEAL 6660

D GB F

Keine harten und splitternden Materialien schneiden! Do not cut hard materials or materials which may splinter! La coupe de matériaux trop durs ou risquant des projections est interdite ! NL Snij geen harde materialen of materiaal dat kan splinteren! Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi! E ¡No cortar materiales duros o materiales que puedan astillarse! S Förstör inte hârt material eller material som kan splittras! FIN Asentakaa laite lasten ulottumattomiin ! N Ikke kutt hardt metall eller materiale som kan splintre ! PL Nie ciąć twardych materiałów lub materiałów, które mogą ulec odpryśnięciu! RUS Äàííûé ðåçàê íå ïðåäíàçíà÷åí äëÿ ðåçêè òâåðäûõ

H TR DK

Ne vágjon kemény vagy olyan anyagot, amely repedhet! Sert veya parçalanabilecek malzemeleri kesmeyiniz! Der må ikke skæres i hårde materialer eller i materialer, der kan splintre! CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré úlomky! P Não cortar materiais duros ou materiais que possam lascar! GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ! SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko razcepijo. SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu vystrelovat ostré úlomky. EST Ärge lõigake kõvasid materjale ega materjale, mis võivad pilbasteks puruneda! CHI UAE

Page 7 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 8
Text on page 8
  • Safety precautions •

The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation" only! Warning! Clips or similar damage the cutting blade.

Disconnect from the mains before starting any service work or before removing the panels!

Replacement of blade and cutting stick may be performed only when the main switch is switched off!

Page 8 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 9
Text on page 9
  • Safety precautions •

IDEAL 4860 • IDEAL 6660

All components which could endanger the operator are covered by a guard!

Operating the machine without safety device is forbidden! (Rear screwed safety guard (A) and panel (B).

Page 9 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 10
Text on page 10
  • Safety precautions •

The cutting action, which is dangerous to the operator,is

  • protected by a two-handed control system (A)
  • and safety beam guard (B).

Protect mains cable against heat, oil and sharp edges!

Page 10 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 11
Text on page 11
  • Safety precautions •

IDEAL 4860 • IDEAL 6660

230V / 10A min 115V / 15A min

Connect the power cord to a single phase socket.

Ensure free access to mains!

When not in use for a longer period switch off. (Main switch to "0").

Page 11 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 12
Text on page 12
  • Safety precautions •

Danger! Blade must always be covered by the pressing bar.

OK

OK

Page 12 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 13
Text on page 13

IDEAL 4860 • IDEAL 6660

Remove the stand from the wooden pallet.

4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set (C).

Page 13 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 14
Text on page 14

Tools can be kept in the holder provided .

Cutting sticks (A) can be put in the tool holder

Page 14 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 15
Text on page 15

IDEAL 4860 • IDEAL 6660

Side tables (A), left and right are available as an option (Nr. 9000 528).

Plug into socket. The machine must be connected directly to the socket.

Page 15 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 16
Text on page 16

It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use.

  • All covers have to be mounted (A).
  • Safety beam guard must be mounted (B).
  • The release for cutting is allowed only if the two-hand safety device is operated at the same time (C)
  • Safety light beam: The machine stops immediately if anyone reaches into the cutting area (D).

We recommend you keep a record of your test results.

STOP

Page 16 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 17
Text on page 17

IDEAL 4860 • IDEAL 6660

Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). The machine is now ready for use.

Press START (C). Machine will automatically go to the start position.

Bright LEDs illuminate the working area (D). The LED button (E) has 4 switching steps Press 1 x brightness 3 Press 2 x brightness 2 Press 3 x brightness 1 Press 4 x OFF

The light can also be switched off by pressing symbol a few and keeping pressed the seconds.

The measurement is set either with the handwheel (A) or by programming (B) the cutting measurements. Measurement is shown on the display in inches or cm (B).

Page 17 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 18
Text on page 18

Optical cutting line (A) that indicates the exact position of the cut. Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required).

Position the paper on the backgauge (A) and side lays left or right (B). To move paper stacks, please use the paper knock-up block (C) provided. (Run backgauge to the front for turning the paper stack).

Page 18 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 19
Text on page 19

IDEAL 4860 • IDEAL 6660

The clamp moves automatically when cutting is activated.

The paper can also be pressed in advance. Clamping and cutting is activated by the actuators (A) on the front table.

The actuator has 2 switching steps:

  1. pre-clamping
  2. automatic clamping and cutting

Pre-clamping Press down both actuators to step 1

Clamp returns Press down completely one of the actuators

Cutting sequence with automatic clamping Press down both actuators to step 2

Page 19 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 20
Text on page 20

Cutting activation: Press both actuators of the two-handed control system (A) simultaneously and keep pressed until the paper is completely cut.

To interrupt or stop cutting: To interrupt or stop cutting, release both actuators (A) of the two-handed control.

Page 20 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 21
Text on page 21

IDEAL 4860 • IDEAL 6660

two-handed control system A - Safety Pre-clamping and cutting

switch B - Overload (blade drive/clamp drive/

C - Backgauge control D - Main switch E - Hand-wheel for backgauge setting F - Key switch G - Backgauge H - Side lay left and right

Start machine

  • Main switch to position "I", insert the key for the control panel and turn to the right. Start screen appears The following functions are changeable: Brightness CM/INCH Touchtone ON/OFF Language
  • Press START J

backgauge moves to the rear and searches for the reference position, wait until a measurement is shown in the display IDEAL 4860 = 45 cm, 17,72 inches IDEAL 6660 = 61 cm, 24,02 inches

  • The DIN measurements in cm (A3, A4, A5, A6) and in inch (LD, LG, LT, hLT) are recallable with the respective buttons.

Warning! Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) see above is stored. For information on how to store see picture below left Is shown on the screen see .

After 30 minutes the screen switches to energy-saving mode The screen is reactivated by touching the keypad area .

Page 21 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 22
Text on page 22

Cutting activation Warning!

  • Run backgauge to the front for turning the paper stack
  • Do not interrupt the upward movement of the blade by performing switching procedures
  • Wait until the display is green before activating a cut Blade must always be at the top and be
  • covered by the clamp. Do not touch the blade (see safety information on page 34). Risk of injury!

Cutting to specified dimensions

  • Press MAN.
  • Enter dimension on the numerical key pad Measurement is shown in red (If a wrong dimension is entered this can be corrected by pressing the Y button) dimension is
  • Press START approached, Measurement is shown in green
  • Insert paper and move by means of the stacking angle to the backgauge and side lay on the left
  • Release the cut.

Cut according to markings Press MAN.

  • Adjust the backgauge with the hand-wheel to the back
  • Insert paper and move by means of the stacking angle to the backgauge and side lay on the left
  • Turn the hand-wheel to the right until the marking on the paper to be cut is below the cutting line indicator
  • The further the hand-wheel is turned to the right, the quicker the backgauge moves. If the hand-wheel is turned to the left the backgauge will return quicker.

Page 22 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 23
Text on page 23

IDEAL 4860 • IDEAL 6660

Eject function If EJECT is pressed instead of START , after inserting the measurement , the backgauge will advance forwards so that paper can be removed. Finally the backgauge moves to the last setting.

Multiple cut

  • Enter the start dimension on the display
  • Advance to the measurement with the START
  • Push the paper to the backgauge
  • Press multiple cut
  • Multiple cut sign appears top left together with the value 00.00
  • Enter multiple cut measurement (appears in red letters)
  • Press START the backgauge advances by the multiple cut size
  • This is repeated everytime a cut is activated.

Exiting program-mode (yellow).

  • Press multiple cut Multiple cut sign and value are deleted.

Page 23 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 24
Text on page 24

Programming This control system enables you to store 99 programs with 99 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with the button j and b . First figure on display = program number. Second figure on display = program step. Smallest cutting measurement: IDEAL 4860 3,5 cm/1.38 inch IDEAL 6660 2,5 cm/0.98 inch

Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off.

Entering a program

  • Press EDIT "Load program no." appears
  • Enter program number 01 ... 99, with (Top number on display = program number)
  • If measurement is shown on the display the program is reserved, select another program
  • Program step "01 Step" 00.00 appears. (Second figure on display = program step.
  • Enter dimension, or move the backgauge to the desired measurement with the hand-wheel
  • Store the measurement ,next program step appears.
  • Enter the next measurement and with Enter store the measurement etc.
  • Should the entered program be required immediately press RUN
  • Press Enter
  • Press START
  • Escape the program mode press MAN.

Cancel a program

  • Press EDIT
  • Scroll with PRG until "Delete program no." appears
  • Enter Program number
  • Press Enter
  • Press Enter .

Page 24 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 25
Text on page 25

IDEAL 4860 • IDEAL 6660

Adapting a program when the printer’s imprint deviates

  • Press RUN "Load program no." appears
  • Enter program number 01 ... 99, and with 2 x Enter proceed to Step 1
  • Correct the cutting position of the backgauge with the hand-wheel
  • MODIFY appears on the screen and the measurement flashes
  • To store press MODIFY
  • Release a cut and turn the paper
  • If the printer’s imprint deviates it can be corrected during the first two cuts via the hand-wheel – see above
  • Correction is only possible during the first two cuts
  • After leaving the RUN mode the original data is stored again.

Delete a step

  • Press EDIT
  • Enter program number, confirm with Enter
  • Select program step with the arrow keys b and j
  • Scroll with STEP until "Delete step no." appears, Press 2 x Enter .

Insert a step

  • Press EDIT
  • Select a program, confirm with Enter
  • Scroll with STEP until "Insert step no." appears
  • Enter insert position e.g. 02
  • Confirm with Enter
  • Enter a measurement
  • Store the measurement with
  • The cutting position can be shown on the screen with the arrow keys b and j .

Changing a program step

  • Press EDIT
  • Select a program, confirm with Enter
  • Scroll with STEP until "Load step no." appears
  • Enter step position e.g. 03
  • Confirm with Enter
  • Enter a new measurement, Store the measurement with .

Page 25 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 26
Text on page 26

Eject function program

  • If a short measurement e.g. 30 cm and then a long measurement e.g. 40 cm is cut at the start of a program then it is wise to insert an EJECT after the first cut so that the paper is pushed to the front.
  • The EJECT function can be added each time a measurement is entered and ejects before advancing to the next measurement. When the eject function is programmed an "E" appears top right in the display.
  • Inserting an Eject function subsequently in the program. Select a program and advance to the step to be changed with the arrow keys b and j Enter the new measurement and before activating the enter button press EJECT .

Example of a program eject function

  • Press EDIT
  • Enter program number e.g. 08
  • Press Enter
  • 1. Enter program Step e.g. 30 cm
  • Press Enter
  • 2. Enter program Step e.g. 40 cm Press EJECT and with Enter store the dimension.

How the example works

  • Press RUN
  • Enter program number 08
  • Press Enter ,
  • Press START, Measurement is approached
  • Insert paper
  • Release cut 1
  • Eject (Ejection is completed, turn the paper)
  • The backgauge moves to program step 2
  • Release cut 2

Multiple cut program

  • Press EDIT
  • Enter program number
  • Enter the 1. program step e.g. start-up measurement 40 cm
  • Store the measurement with Enter
  • Press the multiple cut symbol
  • Enter the number of cuts with the + button (max. 15 cuts) followed by the multiple cut size (cutting width).
  • Store with Enter .

Page 26 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 27
Text on page 27
  • Blade and cutting stick replacement •

IDEAL 4860 • IDEAL 6660

If the cutting quality decreases:

  • Check the cutting depth (see page 34).
  • Check the cutting stick (see page 30).
  • Replace or grind the blade (see page 26 - 34). The blade cannot be ground if the blade height is less than 83 mm/3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen.

Danger! Risk of injury! The blade is extremely sharp. Do not extract or transport the blade without protection. Changing the blade may only be performed by trained staff.

Page 27 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 28
Text on page 28
  • Blade and cutting stick replacement •

Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set

  1. or tool holder (B).

Lower the blade by pressing both cutting actuators (1.). Keep one actuator pressed and turn off the main switch (2.).

Page 28 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 29
Text on page 29
  • Blade and cutting stick replacement •

IDEAL 4860 • IDEAL 6660

The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B).

Only IDEAL 4860 Unscrew the blade screws (C) on the right hand side.

Remove the special wrench and turn on the main switch until the blade returns to the home position.

Page 29 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 30
Text on page 30
  • Blade and cutting stick replacement •

Position the main switch to "0" (1.) Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.).

Remove 2 blade screws (1.) IDEAL 4860 and 3 blade screws (1.) and 3 blade screws (1.) IDEAL 6660 Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4).

Page 30 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 31
Text on page 31
  • Blade and cutting stick replacement •

IDEAL 4860 • IDEAL 6660

Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).

Replacing the cutting stick (not the blade).

  • Turn the blade adjusting screw (A) to the left until it stops. (Otherwise the first cut will be too deep).
  • Remove the cutting stick according to top picure.
  • Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt. Danger! Risk of injury!

Cutting test after replacing the cutting stick (not the blade)

  • Insert the paper and release the cut.
  • If the last sheet of paper is not cut along the entire length turn the blade adjusting screw
  1. ¼ turn to the right.
  • If the last sheet is still not completely cut repeat this process until the last sheet is cut along the entire length.

Page 31 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 32
Text on page 32
  • Blade and cutting stick replacement •

Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A).

  • Make sure there is a space ot 11 mm or 0.43 inches! (B).
  • Blade must be covered! (C). Danger! Risk of injury!

11 mm 0.43 inch

Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).

Page 32 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 33
Text on page 33
  • Blade and cutting stick replacement •

IDEAL 4860 • IDEAL 6660

Lightly tighten 3 (IDEAL 4860 has 2) of the 5 blade screws with washers (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws with washers (3.). Return blade changing tool to tool holder (B).

Only IDEAL 4860 Lightly screw in the right blade screw with the washer (A) when the blade is lowered.

Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position "I" (2.).

Page 33 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 34
Text on page 34
  • Blade and cutting stick replacement •

Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.).

With the special wrench (A) the 3 eccentrics should be screwed down (3.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).

Only IDEAL 4860 Tighten the blade screws (A) on the right hand side.

Turn main switch to position "I" (1.). Blade will return to upper position. Tighten the blade screws (2.) firmly.

Page 34 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 35
Text on page 35
  • Blade and cutting stick replacement •

IDEAL 4860 • IDEAL 6660

Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.

Danger by blade replacement! Blade must always be covered by the pressing bar (see picture below at the left).

OK

Clamping

Blade

OK

Page 35 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 36
Text on page 36
  • Maintenance and cleaning •

Danger! Disconnect the mains before starting any service work or before removing the cover.

Maintenance work may only be performed by trained staff.

Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease). Grease the remaining parts twice a year (see picture). The main switch must be on "0" (B). Remove lower panel (C). Tools in tool set or tool holder.

  • Remove any paper.
  • Grease the machine.
  • Check the 4 joining bolts and 2 pushing bars for wear (D). If necessary inform your service personnel.
  • Mount the machine.

= Greasing points on the machine.

Page 36 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 37
Text on page 37
  • Maintenance and cleaning •

IDEAL 4860 • IDEAL 6660

Safety test The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.

Page 37 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 38
Text on page 38
  • Possible malfuntions •

Machine does not function!

Is the machine plugged in?

Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Release a cut see page 19.

Page 38 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 39
Text on page 39
  • Possible malfuntions •

IDEAL 4860 • IDEAL 6660

Machine turns off:

  • Machine overloaded. Safety button (A) or (B) ejects. (Allow 1 minute cooling time and reset the safety button (A) or (B).
  • Machine blocked.
  • Blade is blunt.

Eliminate the cause, and push the safety button (A).

  • Backgauge blocked

Safety button (C) ejects. Eliminate the cause, and push the safety button (C).

Safety button for:

A = Blade drive

B = Clamping drive

C = Backgauge drive

Page 39 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 40
Text on page 40
  • Possible malfuntions •

Does not cut through the last sheet:

  • Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B) (see page 34).

Poor cutting quality or blade stays in the paper stack.

  • Change the blade (C) (see pages 26 - 34.

Page 40 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 41
Text on page 41
  • Possible malfuntions •

IDEAL 4860 • IDEAL 6660

Display illumination off

  • Machine is plugged in? (A)
  • Main switch on position "I"? (B)
  • Push in the safety button! (C)
  • Check the units fuse and the on-site circuit breaker!

After 30 minutes the screen switches to energy-saving mode The screen is reactivated by touching the keypad area .

Trouble shooting-light beam Cut cannot be activated:

  • Remove all items obstructing the safety area (A) Only the receiver (right-hand) has a
  • display (B) Green = ready for operation Red = light beam is interrupted or error

Page 41 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 42
Text on page 42
  • Possible malfuntions •

Motor runs but blade does not move downwards.

  • Security brake has been activated! Inform the Service Team!

None of the above mentioned methods helped to solve the problem: Contact Service Team under

  • www.ideal.de "Service" service@krug-priester.com

Page 42 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 43
Text on page 43

IDEAL 4860 • IDEAL 6660

Recommended accessories:

Blade

  • Nr. 9000 021 IDEAL 4860
  • Nr. 9000 025 IDEAL 6660

Cutting stick (6 pieces)

  • Nr. 9000 022 IDEAL 4860
  • Nr. 9000 026 IDEAL 6660

Blade changing tool 1

  • Nr. 9000 518 IDEAL 4860
  • Nr. 9000 513 IDEAL 6660

Paper knock-up block 1

  • Nr. 9000 521

Side tables left and right

  • Nr. 9000 528

Page 43 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 44
Text on page 44
  • Technical data •

Technical data:

  • Power supply: 230V/50Hz/1~, 120V/60Hz/1~
  • Cutting height: 80 mm
  • Leakage current < 3,5mA
  • Power cord gauge min. 1,5mm 2 (230V)
  • Power cord gauge AWG 12 (20A) (120V)

The exact technical specifications can be found on the technical specifications sticker

  1. on the machine. A wiring diagram is found in the electrical switch box.

To claim under guarantee, the machine must still carry its original identification label.

Safety light beam 97 ms

  • Total reaction time:
  • Resolution 14 mm/minimum distance: 194 mm
  • Resolution 25 mm/minimum distance: 286 mm

Ambient operating temperature 10 °C - 60 °C Air humidity (not condensating) 15 % - 95 %

IDEAL 4860

IDEAL 6660

Cuttinglength mm

Tabledepth mm

Minimum space requirement (BXTXH) mm

Weight kg

with side tables: (Width) IDEAL 4860 1365 mm

  • * with side tables: (Depth) IDEAL 4860 1020 mm
  • with side tables: (Width) IDEAL 6660 1600 mm
  • * with side tables: (Depth) IDEAL 6660 1250 mm
  • ** with side tables: IDEAL 4860 241 Kg
  • ** with side tables: IDEAL 6660 321 Kg

Page 44 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 45
Text on page 45
  • Technical data •

IDEAL 4860 • IDEAL 6660

This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and 2004/108/EG.

Sound level information: Sound measurement to EN 13023 : 72,5 db (A)

Subject to alteration without notice.

Page 45 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 46
Text on page 46
  • Technical data •

Krug + Priester has a certified quality management system according to DIN EN ISO 9001:2008 and a certified environmental management system according to DIN ISO 14001:2009.

Page 46 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 47
Text on page 47

IDEAL 4860 • IDEAL 6660

D GB F

EG-KONFORMITÄTSERKLÄRUNG

EC-declaration of conformity Déclaration de conformité CE

  • Hiermit erklären wir, daß die Bauart von
  • Herewith we declare that
  • Par la présente, nous déclarons que

GS-ID Nr. 11486001 GS-ID Nr. 11655002

UL-ID Nr. 10486001 UL-ID Nr. 10655002

  • folgenden einschlägigen Bestimmungen entspricht
  • complies with the following provisons applying to it
  • sont conformes aux dispositions pertinentes suivantes

2006/42/EG: Maschinenrichtline, EC Machinery directive, EC Directives machines. 2004/108/EG: EMV Richtline, EMV Electromagnetic compatibility directive, EMV directives compatibilité électromagnétique. 2011/65/EU RoHS Richtlinie, RoHS directive, RoHS directives.

  • Angewendete harmonisierte Normen insbesondere
  • Applied harmonised standards in particular
  • Normes harmonisées utilisées, notamment

EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN ISO 12100; EN 61496-1; EN 61496-2; EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1

29.12.2009 Datum

Bevollmächtigter für technische Dokumentation Authorized representative for technical documentation Représentant autorisé pour la documentation technique

Krug & Priester GmbH u. Co KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany)

Page 47 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 48

Page 48 of 49

MBM Triumph 4860ET Automatic Programmable Paper Cutter Instruction Manual, page 49
Text on page 49

IDEAL • Made in Germany

  • Document Shredders •

IDEAL

  • 72336 Balingen •

Printed in Germany • IDEAL 08/2013

  • Trimmers and Guillotines •

Page 49 of 49 ยท End of manual

Quick start

  1. Four strong people are needed to lift the cutter from the pallet onto the stand; secure it with the 4 screws and fit the shelf.
  2. Plug the cutter directly into a single-phase socket (115V / 15A min or 230V / 10A min).
  3. Check that all covers and the safety beam guard are mounted and that the two-hand control and light beam stop the machine.
  4. Turn the main switch to I, insert the control key and turn it to the right, then press START; the backgauge finds its reference position.
  5. Press MAN, enter the dimension on the keypad and press START; wait until the measurement shows green.
  6. Push the paper against the backgauge and side lay with the knock-up block.
  7. Press both actuators fully (step 2) and hold them until the stack is cut; pressing to step 1 pre-clamps only.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not functionNot plugged in, main switch off, or control system not activated.Plug in, set the main switch to I and turn the key to the right. Page 38
Machine turns offOverload, a blocked machine or a blunt blade trips safety button A (blade drive) or B (clamp drive); a blocked backgauge trips button C.Remove the cause, allow 1 minute cooling time, then push the safety button back in. Page 39
Last sheet is not cut throughWorn cutting stick or blade depth set too high.Turn or reverse the cutting stick and turn the blade adjusting knob ¼ turn to the right at a time until the last sheet is cut along its full length. Page 40
Poor cutting quality or blade stays in the stackBlunt blade.Change the blade. A blade under 83 mm / 3.29" high cannot be re-ground. Page 40
Display illumination offNot plugged in, main switch off, a safety button ejected, a fuse or breaker tripped, or energy-saving mode after 30 minutes.Check power and main switch, push in the safety button, check the fuse and circuit breaker, or touch the keypad to wake the screen. Page 41
Cut cannot be activatedThe safety light beam is interrupted (receiver display shows red).Remove all items from the safety area until the receiver display is green. Page 41
Motor runs but blade does not move downThe security brake has been activated.Contact the service team. Page 42

Frequently asked questions

How many programs can the 4860 store?

99 programs with 99 programmable steps each; programs stay stored when the machine is off. See page 24.

What is the cutting height and smallest cut?

The cutting height is 80 mm and the smallest cutting measurement on the IDEAL 4860 is 3.5 cm / 1.38". See page 44 and page 24.

What are the part numbers for the blade and cutting sticks?

For the IDEAL 4860: blade No. 9000 021, cutting sticks (6 pieces) No. 9000 022, blade changing tool No. 9000 518. Side tables are No. 9000 528. See page 43.

How often should the 4860 be greased?

Grease the backgauge control weekly with a grease gun and the remaining parts twice a year, with the main switch at 0. See page 36.

How many times can a cutting stick be used?

The cutting stick can be turned or exchanged and used eight times. See page 31.