

Page 1 of 49

Page 2 of 49

Text on page 3
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
FIN
Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein. Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available. Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine, et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation et les consignes de sécurité doivent toujours être disponibles. Les instructions d'utilisation et les consi. Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en de veiligheids-voorschriften moeten altijd binnen handbereik zijn. Per favore legga questo manuale di istruzione prima di mettere in funzione il distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono essere sempre disponibili. Le recomendamos lea las instrucciones antes de poner en funcionamiento esta máquina y cumpla las normas de seguridad. Las instrucciones de servicio y seguridad deben estar siempre disponibles. Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig. Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen ! Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla. Lees gjennom denne bruksannvisningen før De tar i bruk maskinen Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen må alltid være tilgjengelig. Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być zawsze dostępne.
RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä
A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie. Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý her zaman kullanýma hazýr olmalýdýr. Før installation af maskinen bedes De venligst læse brugervejledningen brugervejledningen og være opmærksom på sikkerhedsanvisningerne. Brugervejledningen skal altid være tilgængelig. Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní upozornění. Návod k obsluze musí být vzdy dostupný. Por favor leiam o manual de instruções antes de colocar a máquina em operação e vejam as precauções de segurança. As instruções de operação deverão estar sempre disponíveis. ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ. ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ.
CHI
UAE
Page 3 of 49

Text on page 4
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
D GB F NL E S FIN N PL
RUS
H TR DK CZ P GR
Keine Bedienung durch Kinder! Children must not operate the machine! Pas d‘utilisation par un enfant! Geen bediening door kinderen! Non lasciare utilizzare il tagliacarte a bambini! No dejar que la utilicen los niños! Installera maskinen utom räckhåll för barn! Asentakaa laite lasten ulottumattomiin ! Installer maskinen utenfor rekkevidde for barn! Dzieciom nie wolno obsługiwać urządzenia !
Gyerekek a gépet nem kezelhetik Makinayý Çocuklar Kullanmamalýdýr. Må kun betjenes af voksne Stroj nesmí být obsluhován dětmi As crianças não devem trabalhar com a máquina! ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ.
CHI UAE
D GB F NL E S FIN N PL
RUS
H TR DK CZ P GR
Nicht unter das Messer fassen! Do not reach beneath the blade! Ne pas passer les mains sous la lame! Niet met de handen onder het mes komen! Non toccare la lama nella parte inferiore! ¡No tocar debajo de la cuchilla! Sträck inte in handen under kniven! Älä laita kättäsi terän alle ! Plasser aldri hender ol. under kniven ! Nie wkladac rak pod noze!
Ne nyúljon a kés alá!
Elinizi býçaðýn altýna sokmayýnýz!
Stik ikke hænderne ind under knivbladet! Nesahejte pod ostří nože! Não tocar na parte inferior da faca! ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ!
CHI UAE
Page 4 of 49

Text on page 5
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Messer nie lose liegen lassen! Messer nur mit Messerwechselvorrichtung oder im Messertransportkasten befördern! (siehe Seite 31 und 33). Warnung! Verletzungsgefahr! GB Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 31 and 33). Danger! Risk of injury! F Ne jamais laisser la lame sans protections ! Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf. page 31 et 33), ou transportée dans son étui en bois ! Danger! Risques de coupures ! NL Laat nooit de messen alleen achter. Transporteer de messen niet zonder de houten bescherming (zie pagina 31 en 33). Waarschuwing! Opgelet voor ongevallen! Non lasciare mai la lama incustodita. Non rimuovere o trasportare la lama senza protezione. (Vedi pagina 31 e 33). Attenzione! Rischio di infortunio! E ¡No quitar la cuchilla sin prestar atención. No desmontar no transportar la cuchilla sin protección! (vérase pág. 31 y 33) ¡Advertencia! ¡Peligro de hacerse daño! S Lämna aldrig maskinen obemannad. Ta inte ur eller transportera kniven utan skydd. (se sid 31 och 33). Skaderisk! FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta terää ilman suojaa ! (katso sivu 31 ja 33) Loukkaantumisen vaara ! N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller transporter den uten beskyttelse (Se side 31 og 33) FARE ! Muligheter for skade ! PL Nigdy nie pozostawiac nozy bez nadzoru. Nie wyciagac lub transportowac nozy bez oslon! (zobacz strona 31 i 33). Ryzyko skaleczenia sie!
RUS
Soha ne hagyja a kést őrizetlenül! Ne vegye ki vagy ne szállítsa a kést védőtok nélkül! (Lásd 31. és 33. oldal) Veszély! Sérülésveszély! Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz! Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya taþýmayýnýz! (Sayfa 31 ve 33’e bakýnýz) Dikkat! Yaralanma riski!
Page 5 of 49

Text on page 6
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
DK Knivbladet må aldrig efterlades uden opsyn. Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 31 og 33) FARE! Risiko for legemlig beskadigelse. CZ Nikdy nenechávejte nůž bez krytu. Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 31 a 33) Nebezpecí! Riskujete zranení P Deixar a faca sempre em local seguro! Não retirar ou transportar a faca sem protecção! (Ver pág. 31 e 33) Perigo! Risco de dano! GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ! ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 31 & 33 ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ !
CHI
UAE
Page 6 of 49

Text on page 7
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
D GB F
Keine harten und splitternden Materialien schneiden! Do not cut hard materials or materials which may splinter! La coupe de matériaux trop durs ou risquant des projections est interdite ! NL Snij geen harde materialen of materiaal dat kan splinteren! Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi! E ¡No cortar materiales duros o materiales que puedan astillarse! S Förstör inte hârt material eller material som kan splittras! FIN Asentakaa laite lasten ulottumattomiin ! N Ikke kutt hardt metall eller materiale som kan splintre ! PL Nie ciac twardych materialów lub materialów, które moga ulec odprysnieciu!
RUS
Ne vágjon kemény vagy olyan anyagot, amely repedhet! Sert veya parçalanabilecek malzemeleri kesmeyiniz! Der må ikke skæres i hårde materialer eller i materialer, der kan splintre! CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré úlomky! P Não cortar materiais duros ou materiais que possam lascar! GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ!
H TR DK
CHI UAE
Page 7 of 49

Text on page 8
- Safety precautions •
The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation" only!
Disconnect from the mains before starting any service work or before removing the panels!
Replacement of blade and cutting stick may be performed only when the main switch is switched off!
Page 8 of 49

Text on page 9
- Safety precautions • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
All components which could endanger the operator are covered by a guard!
Operating the machine without safety device is forbidden! (Front safety guard (A), rear screwed safety guard (B) and panel (C).
Page 9 of 49

Text on page 10
- Safety precautions •
The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B)
Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A),(correct if distance between cover and table is < 20 mm) main switch (B) and control panel (C) must be checked.
Page 10 of 49

Text on page 11
- Safety precautions • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Protect mains cable against heat, oil and sharp edges!
230V / 10A min 115V / 15A min
Connect the power cord to a single phase socket.
Ensure free access to mains!
Page 11 of 49

Page 12 of 49

Text on page 13
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Only IDEAL 4810/EP IDEAL 4850/EP IDEAL 6550EP Remove the stand from the wooden pallet.
Only IDEAL 4810/EP IDEAL 4850/EP IDEAL 6550EP 4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set (C).
Page 13 of 49

Text on page 14
IDEAL 5221-95EP
The machine is delivered ready for operation. 4 strong people are required to lift the machine from the pallet. Side tables, left and right, (A) are available as accessories. Attach the side tables to the front table so that the upper surface is level. (Screws and nuts are in a plastic bag in the tool set (C). The front and rear wooden panels must be removed for in-house transport on a pallet truck. For transport through narrow doors:
- Remove side tables
- Remove the machine from its base (4 screws)
- Tilt the machine on its side
- Mount the machine to its base
- Screw on all side panels
Only IDEAL 4810-95, 4850-95, 6550-95 Tighten the backgauge crank (A). Parts and tools are in the tool set (C).
Page 14 of 49

Text on page 15
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Only IDEAL 4810-95/EP Attach the enclosed hand-wheel for clamping. Parts and tools are in the tool set (C).
Plug into socket. The machine must be connected directly to the socket.
Page 15 of 49

Text on page 16
It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use.
- All covers have to be mounted (A).
- The release for cutting is allowed only if the cover is closed and the two-hand safety device is operated at the same time (B)
- If the front cover closes by itself the gas spring (X) needs replacing.
We recommend you keep a record of your test results.
Page 16 of 49

Text on page 17
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use.
Only IDEAL 4810-95EP, IDEAL 4850-95EP, IDEAL 5221-95EP, IDEAL 6550-95EP Press button (D). Machine will automatically go to the start position.
IDEAL 4810-95, IDEAL 4850-95, The measurement is set with the backgauge crank (A). Proceed to position generally from the rear. The measurement is shown on the scale (B) just below the indicator and can be read in mm/cm or inches.
Page 17 of 49

Text on page 18
IDEAL 4810-95EP, IDEAL 4850-95EP, IDEAL 5221-95EP, IDEAL 6550-95EP The measurement is set either with the handwheel (A) or by programming (B) the cutting measurements. Measurement is shown on the display in inches or cm (B).
Only IDEAL 4810-95EP If display shows " " the clamp must be completely opened. Turn the hand-wheel for clamping (A) completely to the left until the backgauge (B) is activated.
Page 18 of 49

Text on page 19
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Optical cutting line (A) that indicates the exact position of the cut. Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required).
IDEAL 4810-95 has no cutting line indicator.
Only IDEAL 4810-95, IDEAL4850-95. Pull out the handle to avoid the measurement being wrongly adjusted.
Page 19 of 49

Text on page 20
Position the paper on the backgauge (A) and side lays left or right (B). To move paper stacks, please use the paper knock-up block (C) provided. (Run backgauge to the front for turning the paper stack).
Page 20 of 49

Text on page 21
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
IDEAL 4850-95/EP, IDEAL 5221-95EP
IDEAL 6550-95/EP The clamp moves automatically when cutting is activated.
The paper can also be pressed in advance. Clamping and cutting is activated by pressing button (A) on the front table.
Cutting sequence with automatic clamping
Only 4810-95/EP Clamping is released by the hand-wheel. Before every cut lower the clamp by turning the hand-wheel to the right and tighten with a light twist. The cut is activated by pressing the two buttons exactly at the same time.
Page 21 of 49

Text on page 22
Close the safety guard.
Cutting activation: Press both buttons of the two-handed control system activation (A) simultaneously and them pressed until the paper is completely cut.
To interrupt or stop cutting: To interrupt or stop cutting, release both buttons (A) of the two-hand control.
Page 22 of 49

Text on page 23
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
A - Front safety guard B - Safety two-handed control system
Overload switch
C - (blade
drive/clamp drive/
D - Backgauge control (EP) Paper clamp
E - (only
IDEAL 4810-95/EP)
F - Main switch (EP) or crank handle G - Hand-wheel for backgauge setting
H - Key switch I - Backgauge J - Side lay left and right K - Display cutting size (EP, cm or inch) L - Select program step up M - Select program step down N - Stop and delete input O - Start P - Memory multiple cut Q - Keypad R - Changeover cm - inch S - Clear program T - Select program U - Enter V - Program number W - Program step X - Specified dimensions Y - Display multiple cut
Page 23 of 49

Text on page 24
IDEAL 4810-95EP, IDEAL 4850-95EP, IDEAL 5221-95EP, IDEAL 6550-95EP Start machine
- Main switch to position "I", insert the key for the control panel and turn it to the right. Open the front safety guard
- Press button backgauge moves to the rear and searches for the reference position, wait until a measurement is shown in the display IDEAL 4810-95/EP = 45 cm, 17,72 inches IDEAL 4850-95/EP = 45 cm, 17,72 inches IDEAL 5221-95EP = 52 cm, 20,47 inches IDEAL 6550-95/EP = 61 cm, 24,02 inches
Warning! Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) see above is stored. For information on how to store see picture below left.
Cutting to specified dimensions
- Enter dimension on the numerical key pad LED "S" appears. (If a wrong dimension is entered this can be corrected by pressing the button). button dimension is
- Press approached, LED "S" disappears. Dimensions below 9 cm can only be approached with the button pressed and held. (When the button is released, the backgauge moves to a measurement of 9 cm measurement 9 cm blinks, keep the button pressed, backgauge moves to e.g. 7 cm.
- Insert paper and move by means of the stacking angle to the backgauge and side lay on the left .
- Only IDEAL4810-95/EP Turn the hand-wheel for paper clamping to the right and tighten with a short twist.
- Close the front safety guard
- Release the cut.
cm
inch
Cut according to markings
- Adjust the backgauge with the hand-wheel or crank handle to the back.
- Insert paper and move by means of the stacking angle to the backgauge and side lay on the left
- Turn the hand-wheel or crank handle to the right until the marking on the paper to be cut is below the cutting line indicator.
IDEAL 4810-95 has no cutting line indicator.
Page 24 of 49

Text on page 25
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Only EP machines.
- The further the hand-wheel is turned to the right, the quicker the backgauge moves. If the hand-wheel is turned to the left the backgauge will return quicker.
Only IDEAL4810-95/EP
- Turn the hand-wheel for paper clamping to the right and tighten with a short twist.
- Close the front safety guard
- Release the cut.
Eject function is pressed instead of button If button after inserting the measurement, the backgauge will advance forwards to measurement 9 cm/0,36 inch (standard setting of the machine) so that paper can be removed. Finally the backgauge moves to the last setting.
Adjust the eject-dimension
- Press , press , Press press e on display. Insert the desired dimension.
- Store dimension.
Multiple cut
- Enter the multiple cut size on the display
- Advance to the measurement with the button.
- Push the paper to the backgauge .
- Press button the red LED "M " light will be on.
- Enter the multiple cut size.
- After cutting has been activated press button. Every time the button is pressed, the backgauge will advance by the multiple cut size.
- Pressing the button shows the actual size.
Exiting program-mode
- Press button LED "M " the display.
Y is cleared on
Cutting activation Warning!
- Run backgauge to the front for turning the paper stack.
- Do not interrupt the upward movement of the blade by performing switching procedures.
- Release blade only when LED "S" has gone out.
- Close the front safety guard .
- Blade must always be at the top and be covered by the clamp. Do not touch the blade risk of injury! (see safety information on page 36).
Page 25 of 49

Text on page 26
Programming Only IDEAL 4810_95EP, IDEAL 4850-95EP, IDEAL 5221-95EP, IDEAL 6550-95EP This control system enables you to store 9 programs with 9 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with and . the button First figure on display = program number. Second figure = program step. Dimensions below 9 cm can only be button held pressed. approached with the the entered dimension is " u " on the display too low. the entered dimension is " o " on the display too high. Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off. Should you change to another dimension unit all programmed measurements are converted into the new unit (cm or inch).
Entering a program
- Press P appears on the display.
- ... Enter program number 1...9. (First figure on display = program number).
- Enter dimension, or move the backgauge to the desired measurement with the hand-wheel.
- Store the dimension next program step appears. is used to approach the If the hand-wheel next program cutting position press button step appears.
- Enter the next dimension. (Should an ejection be desired before this button and button cut push the simultaneously).
- Should the entered program be required immediately press (program is closed). again (backgauge moves to the Press dimension of the first program). Or:
- + Escape the program mode.
Eject function program
- Set the measurement push button and simultaneously. e appears shortly on the display. The backgauge will advance and eject the paper and finally return to the position shown on the display.
Page 26 of 49

Text on page 27
IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Programming of multiple cut dimension
- Press P appears on the display.
- ... Enter program number 1 ... 9. First figure on display = program number. Second figure = program step. Enter the cut size on the display .
- Store the dimension.
- ... Enter multiple cut size. Press button E and multiple cut size appears on the display. Press button again F and second multiple cut size appears etc.
- Store the dimension.
- + Escape the program mode. Maximum nine multiple cuts can be entered. Entering the tenth multiple cut will delete the multiple cut and the display will show the actual program step.
Deleting a dimension when programming Press and overwrite the dimension.
Cancel a program
- press P appears on the display.
- ... Enter program number 1 ... 9.
- Press button twice.
Each program has to be cancelled separately. Only single program steps can be overwritten.
Deleting the last program step
- Enter .
- Press . + Escape the program mode.
Page 27 of 49

Text on page 28
Working with programs P appears on the display
- Press
- ... Enter program number 1 ... 9 With the button and you are able to change between several program steps.
With the backgauge moves to the indicated dimension. With the backgauge stops.
General LED "S" blinks the basic position will appear. LED "S" is off the actual dimension appears. In the program mode the ejection of paper is not possible. The ejection of paper has to be programmed.
After each cut press the button the backgauge moves to the next dimension.
Escape the program mode
- Press P appears on the display.
- Press escape the program mode.
Program buttons and programs Button = backgauge position rear Button = backgauge position front Press and simultaneously ( U appears on the display) or Press and simultaneously ( D appears on the display)
- Enter the desired dimension (For example: 29,7 cm x 42 cm can be entered for DIN A3)
- Store dimension.
cm
inch
Display in cm or inch
- Press display changes between cm and inch (see picture left). Measurements (in cm or inches) for the rear reference point of the bachgauge are shown on the top of page 23.
Page 28 of 49

Text on page 29
- Blade and cutting stick replacement • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
If the cutting quality decreases:
- Check the cutting depth (see page 36).
- Check the cutting stick (see page 32).
- Replace or grind the blade (see page 28 - 36). The blade cannot be ground if the blade height is less than 83 mm/3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen.
Danger! Risk of injury! The blade is extremely sharp. Do not extract or transport the blade without protection. Changing the blade may only be performed by trained staff.
Page 29 of 49

Text on page 30
- Blade and cutting stick replacement •
Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set (A).
Close the safety guard (1.). Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.).
Page 30 of 49

Text on page 31
- Blade and cutting stick replacement • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B).
Only IDEAL 4810-95/EP, 4850-95/EP Unscrew the blade screws (C) on the right hand side.
Remove the special wrench and turn on the main switch until the blade returns to the home position.
Warning by IDEAL 4810-95 and IDEAL 4810-95EP Do not turn main switch to position "0" whilst blade is moving upwards! The clamp must always overlap the blade! Danger! Risk of injury!
Page 31 of 49

Text on page 32
- Blade and cutting stick replacement •
Position the main switch to "0" (1.) Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.).
Remove 2 blade screws (1.) IDEAL 4810-95/EP, IDEAL 4850-95/EP and 3 blade screws (1.) IDEAL 5221-95EP, IDEAL 6550-95EP. Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4).
Page 32 of 49

Text on page 33
- Blade and cutting stick replacement • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).
Replacing the cutting stick (not the blade)
- Turn the blade adjusting screw (A) to the left until it stops.(Otherwise the first cut will be too deep).
- Remove the cutting stick according to top picture.
- Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt. Danger! Risk of injury!
Cutting test after replacing the cutting stick (not the blade)
- Insert the paper and release the cut.
- If the last sheet of paper is not cut along the entire length turn the blade adjusting screw
- ¼ turn to the right.
- If the last sheet is still not completely cut repeat this process until the last sheet is cut along the entire length.
Page 33 of 49

Text on page 34
- Blade and cutting stick replacement •
Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A)
- Make sure there is a space ot 11 mm or 0.43 inches! (B).
- Blade must be covered! (C). Danger! Risk of injury!
11 mm 0.43 inch
Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).
Page 34 of 49

Text on page 35
- Blade and cutting stick replacement • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Lightly tighten 3 (IDEAL 4810-95/EP, IDEAL 4850-95/EP has 2) of the 5 blade screws with washers (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws with washers (3.).
IDEAL 4810-95/EP and IDEAL 4850-95/EP Lightly screw in the right blade screw with the washer (A) when the blade is lowered.
Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position "I" (2.).
Page 35 of 49

Text on page 36
- Blade and cutting stick replacement •
Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.). Open the safety guard (4.). With the special wrench (B) the 3 eccentrics should be screwed down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).
Only IDEAL 4810-95/EP and IDEAL 4850-95/EP Tighten the blade screws (A) on the right hand side.
Turn main switch to position "I" (1.). Blade will return to upper position. Tighten the blade screws (2.) firmly.
Warning by IDEAL 4810-95 and IDEAL 4810-95EP Do not turn main switch to position "0" whilst blade is moving upwards! The clamp must always overlap the blade! Danger! Risk of injury!
Page 36 of 49

Text on page 37
- Blade and cutting stick replacement • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
OK
Clamping
Warning by IDEAL 4810-95 and IDEAL 4810-95EP Danger! Blade must always be covered by the pressing bar (see picture below at the left).
Blade
OK
Page 37 of 49

Text on page 38
- Maintenance and cleaning •
Maintenance work may only be performed by trained staff.
Danger! Disconnect the mains before starting any service work or before removing the cover.
Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease). Grease the remaining parts twice a year (see picture). The main switch must be on "0" (B). Remove lower panel and rear wooden panel (C). Tools in tool set.
- Remove any paper.
- Grease the machine.
- Check the 4 joining bolts and 2 pushing bars for wear (D). If necessary inform your service personnel.
- Mount the machine.
Page 38 of 49

Text on page 39
- Maintenance and cleaning • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Safety test The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.
Page 39 of 49

Text on page 40
- Possible malfuntions •
Machine does not function!
Is the machine plugged in?
Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Release a cut see page 21.
Page 40 of 49

Text on page 41
- Possible malfuntions • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Cut cannot be made.
- If cover is open: close it.
- If cover is closed: open and re-close it. (Security check).
Page 41 of 49

Text on page 42
- Possible malfuntions •
Machine turns off:
- Machine overloaded. Safety button (A) ejects. (Allow 1 minute cooling time and reset the safety button (A).
- Machine blocked.
- Blade is blunt. Eliminate the cause, and push the safety button (A).
Only IDEAL 4810-95EP, IDEAL 4850-95EP IDEAL 5221-95EP, IDEAL 6550-95EP
- Backgauge blocked Safety button (B) ejects. Eliminate the cause, and push the safety button (B).
Safety button for:
A = Blade drive
A = Clamping drive
B = Backgauge drive
Page 42 of 49

Text on page 43
- Possible malfuntions • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Does not cut through the last sheet:
- Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B) (see page 36).
Poor cutting quality or blade stays in the paper stack.
- Change the blade (C) (see pages 28 - 36).
Page 43 of 49

Text on page 44
- Possible malfuntions •
IDEAL
"Service"
Motor runs but blade does not move downwards.
- Security brake has been activated! Inform the Service Team! www.ideal.de "Service" service@krug-priester.com
Display illumination off
- Machine is plugged in? (A)
- Main switch on position "I"? (B)
- Push in the safety button! (C)
- Check the units fuse and the on-site circuit breaker!
Page 44 of 49

Text on page 45
- Possible malfuntions • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
IDEAL 4810-95EP, IDEAL 4850-95EP, IDEAL 5221-95EP, IDEAL 6550-95EP Cut cannot be made.
- Measurement has not been reached correctly. LED "S" does not turn off.
- Push the button again. Check the security cover (see page 40).
- Measurement below 9 cm
Hold the button is achieved.
O until the measurement
Only IDEAL 4810-95EP "
- Backgauge does not move and " is shown on the display. Open the clamp Turn the hand wheel to the left as far as possible.
- Backgauge I does not advance to position
(Hand-wheel has been turned to the left). " " is shown on the display. inform service people.
IDEAL
"Service"
None of the above mentioned methods helped to solve the problem: Contact Service Team under
- www.ideal.de "Service" service@krug-priester.com
Page 45 of 49

Text on page 46
Recommended accessories:
Blade
- Nr. 9000 021 IDEAL 4810-95/EP
- Nr. 9000 021 IDEAL 4850-95/EP
- Nr. 9000 130 IDEAL 5221-95EP
- Nr. 9000 025 IDEAL 6550-95/EP
Cutting stick (6 pieces)
- Nr. 9000 022 IDEAL 4810-95/EP
- Nr. 9000 022 IDEAL 4850-95/EP
- Nr. 9000 024 IDEAL 5221-95EP
- Nr. 9000 026 IDEAL 6550-95/EP
Blade changing tool 1
- Nr. 9000 511 IDEAL 4810-95/EP
- Nr. 9000 511 IDEAL 4850-95/EP
- Nr. 9000 512 IDEAL 5221-95EP
- Nr. 9000 513 IDEAL 6550-95/EP
Paper knock-up block 1
- Nr. 9000 521 IDEAL 4810-95/EP
- Nr. 9000 521 IDEAL 4850-95/EP
- Nr. 9000 521 IDEAL 5221-95EP
- Nr. 9000 521 IDEAL 6550-95/EP
Side tables left and right
- Nr. 9000 530 IDEAL 5221-95EP
Page 46 of 49

Text on page 47
- Technical data • IDEAL 4810-95/EP • IDEAL 4850-95/EP • IDEAL 5221-95EP • IDEAL 6550-95EP
Technical data:
- Power supply: 230V/50Hz/1~,115V/60Hz/1~ length:
- Cutting 475 1,2,3,4 mm, 520 5 mm, 650 6 mm
- Cutting height: 80 1 mm depth: 458 mm, 450 2 mm, 458 3 , 450 4 ,
- Table 520 5 mm, 610 6 mm
- Sound level EN 13023: 71 dB (A)
- Minimum space requirement (width x depth x height)
755 1,2,3,4 / 855 5 / 1560 5,(7) / 995 6 mm x 970 1,2,3,4 / 1067 5 / 1260 6 mm x 1360 1,2 / 1230 3,4 / 1260 5 / 1220 6 mm
194 1 , 200 2 , 209 3 , 215 4 , 262 5 /276 5,(7) ,
- Weight:
The exact technical specifications can be found on the technical specifications sticker (A) on the machine. A wiring diagram is found in the electrical switch box. IDEAL 4810-95 IDEAL 4810-95EP IDEAL 4850-95 IDEAL 4850-95EP IDEAL 5221-95EP IDEAL 6550-95EP with side tables
This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 98/37, 73/23 and 89/336.
Sound level information: The sound level is 71 db (A) as defined by 13023.
Subject to alteration without notice.
Page 47 of 49

Text on page 48
D GB F NL
E
EG-KONFORMITÄTSERKLÄRUNG
EC-declaration of conformity Déclaration de conformité CE EG-verklaring van overeenstemming Dichiarazione CE di conformità Declaración CE de conformidad
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
- Hiermede verklaren wij, dat de in de handel gebrachte machine
- Si dichiara che il modello della
- Por la presente, declaramos que la
4810-95 EP: 4850-95 EP: 5221-95 EP; 6550-95 EP:
4810-95; 4850-95
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
- voldoet aan de eisen van de in het vervolg genoemde bepalingen
- è conforme alle seguenti disposizioni pertinenti
- satisface las disposiciones pertinentes siguientes
EG 98/37; EG 73/23; EG 89/336
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
- Normas harmonizadas utilizadas, em particular
- Norme armonizzate applicate in particolare
- Gebruikte geharmoniseerde normen, in het bijzondere
- Normas armonizadas utilizadas particularmente
EN 60204-1; EN 1010-1; EN 1010-3; EN ISO 61000-3-2; EN ISO 61000-3-3; EN ISO 12100-1; EN ISO 12100-2; EN 294; EN 954-1; EN 13023;
Krug & Priester GmbH u. Co KG 72336 Balingen, Germany
22.03.2005 Datum
Wolfgang Priester
- General Manager -
Page 48 of 49

Text on page 49
IDEAL • Made in Germany
IDEAL Krug & Priester
Printed in Germany • IDEAL 07/2005 • G
Page 49 of 49 Β· End of manual
Quick start
- Set up: remove the stand from the wooden pallet. Use 4 strong people to lift the machine onto the stand, secure it with 4 screws (A) and put the shelf (B) on the stand. Parts and tools are in the tool set.
- Connect power: plug the power cord directly into a single phase socket rated 230V / 10A min or 115V / 15A min, and keep free access to the mains.
- Check the safety devices: make sure all covers are mounted and that a cut can only be released with the cover closed and both buttons of the two-hand control pressed at the same time.
- Start the machine: set the main switch to "I", insert the key and turn it to the right, open the front safety guard and press the start button. The backgauge finds its reference position and the display shows 61 cm, 24.02 inches on the IDEAL 6550-95/EP.
- Set the size: enter the dimension on the numerical keypad, or move the backgauge with the hand-wheel. Dimensions below 9 cm are only reached while you hold the button pressed.
- Load the paper: place the stack against the backgauge and the side lay, using the paper knock-up block to move it.
- Cut: close the safety guard, then press both buttons of the two-hand control at the same time and keep them pressed until the paper is completely cut. The clamp moves automatically. Release both buttons to stop.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not function | Not plugged in, main switch off, or control system not activated | Check the plug, set the main switch to "I" and turn the key to the right. Page 40 |
| Cut cannot be made | Front cover open or security check not completed | If the cover is open, close it. If it is closed, open and re-close it. Page 41 |
| Machine turns off | Machine overloaded or blocked, or blade is blunt, so safety button (A) ejects | Eliminate the cause, allow 1 minute cooling time and push safety button (A) back in. Page 42 |
| Backgauge stops moving | Backgauge blocked, so safety button (B) ejects | Eliminate the cause and push safety button (B) back in. Page 42 |
| The last sheet is not cut through | Worn cutting stick or blade depth too shallow | Turn or turn around the cutting stick and readjust the blade depth knob ΒΌ turn to the right at a time until the last sheet is cut. Page 43 |
| Poor cutting quality or blade stays in the paper stack | Blade is blunt | Change the blade following the blade replacement steps. Page 43 |
| Motor runs but the blade does not move down | Security brake has been activated | Inform the Service Team. Page 44 |
| Display illumination is off | No power to the machine | Check the plug, set the main switch to "I", push in the safety button, and check the unit fuse and the on-site circuit breaker. Page 44 |
| Cut cannot be made and LED "S" does not turn off | Measurement has not been reached correctly | Push the button again and check the security cover. Page 45 |
| Front cover closes by itself | Worn gas spring (X) | Have the gas spring replaced. Page 16 |
Frequently asked questions
What is the cutting length of the IDEAL 6550-95EP?
The cutting length is 650 mm and the table depth is 610 mm. The sound level is 71 dB (A). See page 47.
How many programs can I store?
The control stores 9 programs with 9 programmable steps, and each step is one measurement. Programs stay stored when the machine is off, and they convert if you switch between cm and inch. See page 26.
Can the blade be sharpened?
Yes, but only by a qualified supplier or the manufacturer Krug & Priester. A blade with a height of less than 83 mm/3.29 inches cannot be ground and must be replaced. See page 29.
How long does a cutting stick last and what is the part number?
Each cutting stick can be turned and used eight times. For the IDEAL 6550-95/EP, the cutting stick (6 pieces) is Nr. 9000 026 and the blade is Nr. 9000 025. See page 33, page 46.
