Morgana 104-Squarefold User Manual, page 1

Page 1 of 18

Morgana 104-Squarefold User Manual, page 2
Text on page 2

Square fold 104

Operator Manual

Morgana Systems Limited ▪ United Kingdom ▪ www.morgana.co.uk ▪ Telephone: ( 01908 ) 608888 ▪ Facsimile: ( 01908 ) 692399

Page 2 of 18

Morgana 104-Squarefold User Manual, page 3
Text on page 3

SquareFold

Model 104 Operator Manual

Page 3 of 18

Morgana 104-Squarefold User Manual, page 4

Page 4 of 18

Morgana 104-Squarefold User Manual, page 5
Text on page 5

Table of contents

Introduction

Getting to know the SquareFold Model 104

Main components The control panel

Making square folds Bypass mode Stacker full sensor Operating the SquareFold

Cleaning the feed belts

Clearing jams Troubleshooting

Making Square folds

Maintenance

Troubleshooting

Specification

SquareFold Model 104 Operator Manual

Page 5 of 18

Morgana 104-Squarefold User Manual, page 6
Text on page 6
  1. Introduction

1.1 Operational safety

Attention to the following notes ensures the continued safe operation of your equipment.

Always connect the equipment to a properly grounded power source receptacle. In doubt, have the receptacle checked by a qualified electrician.

WARNING: Improper connection of the equipment grounding conductor can result in electrical shock.

Always follow all warnings marked on, or supplied with, the equipment.

Always locate the equipment on a solid support surface with adequate strength for the weight of the machine.

Always exercise care in moving or relocating the equipment.

Always keep magnets and all devices with strong magnetic fields away from the machine.

Never use a ground adapter plug to connect the equipment to a power source receptacle that lacks a ground connection terminal.

Never attempt any maintenance function that is not specifically described in this documentation.

Never remove the covers or guards that are fastened with screws.

Never install the unit near a radiator or any other heat source.

Never override or “cheat” electrical or mechanical interlock devices.

Never operate the equipment if you notice unusual noises or odors. Disconnect the power cord from the power source receptacle and call your customer service engineer to correct the problem.

SquareFold Model 104 Operator Manual

Page 6 of 18

Morgana 104-Squarefold User Manual, page 7
Text on page 7
  1. Getting to know the SquareFold

This chapter contains basic information about the SquareFold and its components.

2.1 Main Components

  1. Manual feed tray (Off-line Model)

SquareFold Model 104 Operator Manual

Page 7 of 18

Morgana 104-Squarefold User Manual, page 8
Text on page 8

2.1 Main Components cont.

  1. Stacker full sensor
  2. Main Power switch

SquareFold Model 104 Operator Manual

Page 8 of 18

Morgana 104-Squarefold User Manual, page 9
Text on page 9

2.2 Control Panel

The control panel of the SquareFold has one button to select the different modes. The control panel also has a number of indicators to display the operation mode and to display if a jam occurs.

  1. Mode 1: 6 to 10 sheets *
  2. Mode 2: 11 to 15 sheets *
  3. Mode 3: 16 to 24 sheets*
  4. Mode select button
  5. Bypass mode: 0 to 5 sheets

Note:

  • 80 gsm or 20 lb bond

SquareFold Model 104 Operator Manual

Page 9 of 18

Morgana 104-Squarefold User Manual, page 10
Text on page 10
  1. Making square folds

Description The SquareFold takes your normal booklets and makes them look more like perfect bound (glue bound) books. The output lays flat for easy packing and you are also able to print on the back (spine) of the book for easy retrieval in bookshelves. The SquareFold runs up to 1800 sets / hour depending on which mode that is selected.

3.1 Square fold booklets

In order to produce optimum book quality the SquareFold unit operates in 3 different modes depending on the thickness of the book. Select mode by pressing the mode select button.

Mode selection guide lines

  • Mode 1 for 6–10 sheets (80 gsm or 20 lb bond stock)
  • Mode 2 for 11–15 sheets (80 gsm or 20 lb bond stock)
  • Mode 3 for 16 or more (80 gsm or 20 lb bond stock)

3.2 Bypass mode

Forming the spine square is not adviseable for booklets containing 5 sheets or less. Select bypass mode when making booklets with less than 6 sheets, or when no forming of the spine is desired.

3.3 Stacker full Sensor

The SquareFold is equipped with a stacker full sensor. In mode 1 and 2, stacker full signal appears 30 booklets after the stacker full sensor has been blocked. In mode 3 and Bypass, stacker full signal appears 20 booklets after the stacker full sensor has been blocked. Whenever the books are removed the count starts from zero again. If the stacker full function is not desired, disconnect the stacker full plug from its receptacle.

SquareFold Model 104 Operator Manual

Page 10 of 18

Morgana 104-Squarefold User Manual, page 11
Text on page 11

3.4 Operating the SquareFold

Switch on the Main Power Switch. Place a finished booklet on the stacker. Adjust the stacker by lifting up rear end and move it in/outwards to fit the booklet. Select mode according to section 3.1/3.2. The SquareFold is now set up to receive booklets delivered from the Trimmer or fed by hand.

NOTE: When running the model 104 together with a model 100 collator and mode 3 is selected, reduce the speed of the collator to 1200 sets per hour.

Adjust the manual feed tray side guide to the width of the booklet. Place the booklet on the manual feed tray and gently push it in (spine first). The feed belts energize automatically and pulls the booklet into the SquareFold. When the book exits the SquareFold, the next booklet can be fed into the SquareFold.

SquareFold Model 104 Operator Manual

Page 11 of 18

Morgana 104-Squarefold User Manual, page 12
Text on page 12
  1. Maintenance

4.1 Cleaning the Feed Belts

Clean the feed belts using a mild soap detergent every 10 000 sets or earlier if needed.

  1. Troubleshooting

5.1 Clearing Jam

Open top cover, lift up both infeed belts and take out the jammed booklets.

Place feed belts in their normal position and close the top cover.

SquareFold Model 104 Operator Manual

Page 12 of 18

Morgana 104-Squarefold User Manual, page 13
Text on page 13

5.2 Troubleshooting

PROBLEM

POSSIBLECAUSES

ThejamindicationLEDJaminsideSquareFold isflashing . module .

ACTION

Openthetopcoverand takeoutthejammed s e t . Seesection 5 . 1 . Clearthestackerfrom booklets .

Thereisprintresidue onthecoverofthe SquareFoldbooklets .

Thereisprintresidueonthe belts .

Cleanthefeedbelt accordingtosection 4 . 1 .

Thereisprintresidue onthespine .

Thereisprintresidueinside theSquareFold .

Runsetswithwhite covers ( notprinted ) until residuedisappears .

Thebookletisnotenough pressed .

Correctthemode . Changetohighermode 2 o r 3 .

Thebookletispressedtoo much .

Correctthemode . Changetolowermode 2 o r 1 .

Whenthebookletispressed toomuch , thefoldcan becomecorrugated . Especiallyonbooklets containingfewsheets .

Correctthemode . Changetomode 2 , 1 o r bypass .

SquareFold Model 104 Operator Manual

Page 13 of 18

Morgana 104-Squarefold User Manual, page 14
Text on page 14
  1. Technical Specification

6.1 Technical Specification

Model 1 0 4 SquareFold

Mode 1 Mode 2 Mode 3

Upto 2 4 sheetsof 8 0 g s m ( 9 6 pagebook ) ( 2 0 lbbond )

Dimension ( HxWxD )

SquareFold Model 104 Operator Manual

Page 14 of 18

Morgana 104-Squarefold User Manual, page 15

Page 15 of 18

Morgana 104-Squarefold User Manual, page 16

Page 16 of 18

Morgana 104-Squarefold User Manual, page 17

Page 17 of 18

Morgana 104-Squarefold User Manual, page 18

Page 18 of 18 ยท End of manual

Quick start

  1. Switch on the Main Power Switch.
  2. Place a finished booklet on the stacker and adjust the stacker in or out to fit it.
  3. Press the mode select button: Mode 1 for 6–10 sheets, Mode 2 for 11–15, Mode 3 for 16 or more, or Bypass for 5 sheets or fewer.
  4. Adjust the manual feed tray side guide to the booklet width.
  5. Gently push the booklet in spine first; the feed belts pull it in automatically.
  6. Feed the next booklet once the previous one exits.

Troubleshooting

ProblemLikely causeFix (from the manual)
Jam indication LED is flashingJam inside the SquareFold moduleOpen the top cover, lift both infeed belts, remove the jammed set and clear the stacker of booklets. Page 13
Print residue on booklet coversPrint residue on the beltsClean the feed belts with a mild soap detergent. Page 13
Print residue on the spinePrint residue inside the SquareFoldRun sets with white (unprinted) covers until the residue disappears. Page 13
Booklet is not pressed enoughMode too low for the bookletChange to a higher mode (2 or 3). Page 13
Booklet is pressed too much or the fold is corrugatedMode too high, especially on booklets with few sheetsChange to a lower mode (2, 1 or bypass). Page 13

Frequently asked questions

Which mode should I use?

Mode 1 for 6–10 sheets, Mode 2 for 11–15 sheets, Mode 3 for 16 or more (80 gsm / 20 lb bond). Use Bypass for 5 sheets or fewer. See page 10.

How thick a booklet can it handle?

Up to 24 sheets of 80 gsm (20 lb bond), a 96-page book. See page 14.

How fast is it?

Up to 1,800 sets per hour depending on mode. With a Model 100 collator in Mode 3, reduce the collator to 1,200 sets per hour. See page 10 and page 11.

How often should the feed belts be cleaned?

Every 10,000 sets or earlier if needed, using a mild soap detergent. See page 12.

How does the stacker full sensor work?

In Modes 1 and 2 it signals 30 booklets after the sensor is blocked; in Mode 3 and Bypass, after 20. Unplug the sensor if you don't want it. See page 10.