Morgana 65031 User Manual, page 1

Page 1 of 40

Morgana 65031 User Manual, page 2

Page 2 of 40

Morgana 65031 User Manual, page 3

Page 3 of 40

Morgana 65031 User Manual, page 4

Page 4 of 40

Morgana 65031 User Manual, page 5

Page 5 of 40

Morgana 65031 User Manual, page 6

Page 6 of 40

Morgana 65031 User Manual, page 7

Page 7 of 40

Morgana 65031 User Manual, page 8

Page 8 of 40

Morgana 65031 User Manual, page 9

Page 9 of 40

Morgana 65031 User Manual, page 10

Page 10 of 40

Morgana 65031 User Manual, page 11

Page 11 of 40

Morgana 65031 User Manual, page 12

Page 12 of 40

Morgana 65031 User Manual, page 13

Page 13 of 40

Morgana 65031 User Manual, page 14

Page 14 of 40

Morgana 65031 User Manual, page 15

Page 15 of 40

Morgana 65031 User Manual, page 16

Page 16 of 40

Morgana 65031 User Manual, page 17

Page 17 of 40

Morgana 65031 User Manual, page 18

Page 18 of 40

Morgana 65031 User Manual, page 19

Page 19 of 40

Morgana 65031 User Manual, page 20

Page 20 of 40

Morgana 65031 User Manual, page 21

Page 21 of 40

Morgana 65031 User Manual, page 22

Page 22 of 40

Morgana 65031 User Manual, page 23

Page 23 of 40

Morgana 65031 User Manual, page 24

Page 24 of 40

Morgana 65031 User Manual, page 25

Page 25 of 40

Morgana 65031 User Manual, page 26

Page 26 of 40

Morgana 65031 User Manual, page 27

Page 27 of 40

Morgana 65031 User Manual, page 28

Page 28 of 40

Morgana 65031 User Manual, page 29

Page 29 of 40

Morgana 65031 User Manual, page 30

Page 30 of 40

Morgana 65031 User Manual, page 31

Page 31 of 40

Morgana 65031 User Manual, page 32

Page 32 of 40

Morgana 65031 User Manual, page 33

Page 33 of 40

Morgana 65031 User Manual, page 34

Page 34 of 40

Morgana 65031 User Manual, page 35

Page 35 of 40

Morgana 65031 User Manual, page 36

Page 36 of 40

Morgana 65031 User Manual, page 37

Page 37 of 40

Morgana 65031 User Manual, page 38

Page 38 of 40

Morgana 65031 User Manual, page 39

Page 39 of 40

Morgana 65031 User Manual, page 40

Page 40 of 40 ยท End of manual

Quick start

  1. Fit the guards and stacker: The machine will not run until the main guard is correctly fitted. Locate the stacker support shafts in the catch plates and lower it into place. The machine will not run with the exit guard lowered.
  2. Set the loading table: Slacken the four screws at the ends of each manifold and center the paper. Set the operator-side manifold square. Fit the non-operator manifold so the paper is snug but not tight.
  3. Set the paper gate: The standard horizontal setting is 10 mm (3/8 inch) from the mounting chassis. Set the height to about three thicknesses of paper. Do not adjust it while the machine runs.
  4. Fit the numbering head: Mount a head on a collar using the scale for position. Set the digit wheels with the stylus supplied. Standard heads have seven digits.
  5. Set the inking: Set the ink transfer roller so it runs fully over the numbering head. Position the ink pod so it inks the transfer roller above the head.
  6. Start up in order: Turn the head by hand first. Switch on the compressor and let the pump reach full speed before you use the System Switch. Plug the cord straight into a wall outlet, not an extension cable.
  7. Make ready: Operate the feed switch to run a sheet through and check the number position. If the first sheet does not print, try a second. If it still does not, check the platen pressure.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine dead, no lights on the front panelNot switched on, a blown fuse in the plug, a fault in the power supply or a loose power lead.Switch the main isolator on, replace the fuse, check the supply and check the connection. Page 39
System Switch will not latchA guard is not closed, a system fuse fault or a defective switch.Make sure the guards are securely closed. Check the fuses are intact and the holders are secure. Call a service agent if needed. Page 39
Drive motor will not run with the switch latchedA motor fuse fault, worn motor brushes, paper jammed in the rollers or a component fault.Check the fuse and its holder, check and replace the brushes, and remove all paper from inside the machine. Call a service agent for a component fault. Page 39
Machine will not feed, no suction to the rollerThe compressor is off, the vacuum control is off, the control valve is not operating, auto-reset is not active or a hose is split or disconnected.Switch the compressor on, turn the vacuum control to max, check connections and fuse, and check all hoses. For auto-reset, switch the isolator off, wait 30 seconds and switch it back on. Page 39
Machine will not numberAuto-reset not active, the number on/off switch is off, or the sensors are dirty.Switch the isolator off, wait 30 seconds and back on. Turn the number switch on. Clean the sensors as described in section 10.2. Page 39
Compressor will not runA loose power lead or an overheated compressor.Check the lead. Let the compressor cool and check the filters. Page 39
Double sheets feed throughThe paper gate gap is too large.Reset the paper gate height to about three thicknesses of paper. An excessive gap is the most likely cause of double-sheet feeding. Page 13

Frequently asked questions

What sheet sizes can the Morgana numbering machine run?

The minimum sheet width is 125 mm and the minimum length is 210 mm. The maximum length and width is 460 mm, and the maximum print area is 375 mm. See page 28.

How many digits can a numbering head print?

Standard heads have seven digits. If fewer are needed, up to six zeros can be pushed down so they do not print, though this may not apply to all heads. See page 15.

How much platen pressure should I use?

Use the lowest platen pressure that gives a satisfactory print. Too much pressure will damage the machine. See page 10.

How do I clear a paper jam?

Remove the grub screw behind the handwheel with a 2.5 mm Allen key so the input rollers, output rollers or platen can be turned back by hand. Do not reverse the main print shaft, and do not cut the paper out. See page 33.

How do I care for a re-inkable roller?

After running, lift the pod clear of the transfer roller and store it on its stowage points or upside down on a non-slip surface. A roller left in contact can develop a flat. It also dries out and solidifies if left without inking for more than a week, so this system suits frequent use. See page 22.