
Text on page 1
Morgana AutoCreaser Pro 50 High Speed Creasing Machine
Parts List

Morgana AutoCreaser Pro 50 High Speed Creasing Machine
Parts List
Page 1 of 30

AutoCreaser Pro 50
DOCUMENT CREASING MACHINE ILLUSTRATED PARTS MANUAL MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920 ISSUE 7 NOVEMBER 2011 70-130
Page 2 of 30

INTRODUCTION
AutoCreaser Pro 50
ILLUSTRATED PARTS MANUAL The Illustrated Parts Manual has been designed to assist when selecting a part or assembly which may be required to service or repair your machine.
The index on page four lists all of the major assemblies in the order in which the machine is constructed.
The following page demonstrates how to recognise a part from a sub-assembly and shows the quantity contained within the major assembly.
The major assembly number and description is listed at the top of the page and should always be quoted when ordering parts or when seeking technical advice.
Before ordering parts confirm that the model number of the machine (listed at the top of page four) is identical to the number stamped on the specification plate. Whilst checking this, make a note of the serial number also stamped on the plate.
Some components will not be made available individually as they form part of a sub-assembly which may require specialist tools and knowledge to dismantle. The machine may not perform correctly if attempts are made to repair sub-assemblies of this type.
NOTE.... ALWAYS READ THE OPERATORS MANUAL BEFORE MAKING ANY ADJUSTMENTS TO YOUR MACHINE AND ALWAYS DISCONNECT THE POWER SUPPLY BEFORE REMOVING ANY COVERS.
MyBinding.com Page 2 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 3 of 30

AutoCreaser Pro 50
MyBinding.com CREASER 5500 NE Moore Court Page 3 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 4 of 30

730820T CONTENTS
SECTION ASSEMBLY DESCRIPTION PAGE
1 7-01-18 MAIN ASSEMBLY 6
2 7-03-14 FEED BED ASSEMBLY 10
3 730820T FINAL ASSEMBLY 12
4 7-06-13 CREASER UNIT 20
5 7-08-13 STACKER ASSEMBLY 28
NOTE.... TIP.... To assist you in quickly finding the section you require, there are numbered tabs positioned down the outside edges of each page.
MyBinding.com Page 4 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 5 of 30

AutoCreaser Pro 50
DOCUMENT CREASING MACHINE
MyBinding.com CREASER 5500 NE Moore Court Page 5 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 6 of 30

7-01-18 MAIN ASSEMBLY
MyBinding.com Page 6 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 7 of 30

AutoCreaser Pro 50 MAIN ASSEMBLY 7-01-18 IT EM No. PA R T No . Q T Y. D E S C R IP T IO N 1 71-01-03 1 A D A P T O R A S S Y - Ø 2 4 / Ø 2 4 - S V1 9 0 - D r u m B lo w - C A R D M A S T E R 2 7 1 -0 0 2 -0 4 2 T IE BA R - A C 5 0 3 71-005 4 S UPPO R T S PO O L . 4 71-010 1 PIVO T BU S H - S te pp e d. 5 7 1 -0 1 3 -0 2 1 T I L T L E VE R - M K 2 . 6 71-015 2 P A D - S t a ck e r. 7 71-016 4 S H O C K S L E E VE . 8 7 1 -0 1 8 -0 2 1 P L A T E - B la n k i n g - A u to C r e a s e r . 9 7 1 -0 5 2 -0 1 2 A X L E - A u to C re a s e r 5 0 . 10 7 1 -0 5 3 -0 2 1 B L O W E R S U P P O R T - A u to C re a s e r 5 0 M k 4 . 11 7 1 -0 5 5 -0 1 2 W H EEL CO LL A R 12 7 1 -0 7 1 -0 2 1 M A IN F R A M E - A u to C re a s e r 5 0 M k 4 . 13 7 1 -0 7 2 -0 2 1 PL IN T H - A u to C re a s e r 5 0 M k 4 . 14 7 1 -0 8 6 -0 2 1 F a n M T G . P la te - Ø 1 2 0 15 7 5 -2 0 8 -0 1 1 T o w e r B la n k - O p S i d e 16 7 5 -2 0 8 -0 3 1 T o w e r B la n k - L a y S id e - C a b le R o u te 17 7 5 -2 2 9 -0 1 1 F a n G u a rd A s s y 18 7 5 -3 1 6 -0 2 1 F A N & L E A D A S S Y. - A C 5 0 Peo. 19 7 5 -4 1 5 -0 2 1 BA F F L E PL A T E - L o w e r - A u to C re a s e r 5 0 M k 4 . 20 7 5 -4 2 4 -0 4 1 C O N T R O L L E G A S S E M BL Y - A u to C re a s e r 5 0 M k 4 . 21 7 8 -0 5 7 -0 1 2 H O O P H O O K. 22 62-006 2 NYL O N W H E E L . 23 9 1 -0 0 6 -0 5 1 W H E E L T U B E - O p. S ide - A u to C re a s e r 5 0 . 24 9 1 -0 0 6 -0 6 1 W H E E L T U B E - L a y S i d e - A u to C r e a s e r 5 0 . 25 9 1 -0 2 5 -0 4 2 B U N G - C o m p re s s o r - Ø 2 5 P i p e . 26 9 1 -0 2 5 -0 5 2 B U N G - C o m p re s s o r - Ø 4 0 P i p e . 27 9 1 -1 0 4 -0 1 1 F A N H UB - S V1 9 0 . 28 601-01 5 4 H o le B u s h in g - S p lit - Ø 3 8 29 601-16 1 3 VI B R A T I O N M O U N T - S t u d . 30 603-04 1 4 S PIR O L S PA C ER - Ø 4 x Ø 5 .6 5 x 4 L g . 31 605-05 8 4 NYL O N S PA C E R - Ø 7 .9 4 x Ø 4 .3 4 x 6 .3 5 32 613-33 9 2 C A BL E T IE M O UN T IN G 33 615-01 4 8 C IR C L IP - E XT E R N A L - Ø 1 5 34 617-00 8 2 W heel - Ø 100 35 621-02 5 1 FA N - PL A S T IC 5 BL A D E 6 " C C W 621-03 2 1 B lo w e r S V1 9 0 ( 5 0 H z ) 36 621-03 8 1 B lo w e r S V1 9 0 ( 6 0 H z ) 37 650-02 8 6 C A BL E T IE M T G . - P u s h F it. 38 4 0 1 -0 2 -0 4 0 -0 0 6 4 S cr e w - P a n P o z i T a p t it e - M 4 x 6 L g . 39 4 0 1 -0 2 -0 4 0 -0 0 8 18 S cr e w - P a n P o z i T a p t it e - M 4 x 8 L g . 40 4 0 1 -0 2 -0 4 0 -0 1 2 4 S cr e w - P a n P o z i T a p t it e - M 4 x 1 2 L g . 41 4 0 2 -0 2 -0 3 0 -0 8 0 2 S C R E W - C o u n te rs u n k P o z i T a p ti te - M 6 x 8 L g . 42 4 0 2 -0 2 -0 4 0 -0 0 6 2 S cr e w - C s k H d . T a p t it e - M 4 x 6 L g . 43 4 0 2 -0 2 -0 4 0 -0 0 8 6 S cr e w - C s k H d . T a p t it e - M 4 x 8 L g . 44 4 0 3 -0 1 -0 5 0 -0 1 0 2 S C R E W - S o ck e t C a p H e a d - M 5 x 1 0 L g . 45 4 0 3 -0 1 -0 5 0 -0 2 0 2 S C R E W - S o ck e t C a p H e a d - M 5 x 2 0 L g . 46 4 0 3 -0 1 -0 6 0 -0 1 0 4 S C R E W - S o ck e t C a p H e a d - M 6 x 1 0 L g . 47 4 0 4 -0 1 -0 6 0 -0 1 2 2 S C R E W - S o ck e t C o u n te r s u n k H e a d - M 6 x 1 2 L g . 48 4 0 5 -0 1 -0 6 0 -0 1 2 1 S C R E W - S o ck e t B u t to n H e a d - M 6 x 1 2 L g . 49 4 0 5 -0 1 -0 8 0 -0 1 6 4 S C R E W - S o ck e t B u t to n H e a d - M 8 x 1 6 L g . 50 4 0 5 -0 1 -0 8 0 -0 1 0 2 S C R E W - S o ck e t B u t to n H e a d - M 8 x 1 2 L g . 51 4 0 5 -0 1 -0 8 0 -0 8 0 2 S C R E W - S o ck e t B u t to n H e a d - M 8 x 5 0 L g . 52 4 0 9 -0 1 -0 4 0 -0 0 6 2 S cr e w - S k t S e t S c re w - F la t P t. - M 4 x 6 L g . 53 4 6 1 -0 1 -0 4 0 4 N U T - F u ll - M 4 54 4 6 1 -0 1 -0 6 0 5 N U T - F u ll - M 6 55 481-04 0 4 W A S H E R - P la i n - M 4 56 481-05 0 2 W A S H E R - P la i n - M 5 57 481-06 0 5 W A S H E R - P la i n - M 6 58 481-08 0 4 W A S H E R - P la i n - M 8
MyBinding.com CREASER 5500 NE Moore Court Page 7 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 8 of 30

7-01-21 MAIN ASSEMBLY
MyBinding.com Page 8 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 9 of 30

AutoCreaser Pro 50
BLANK PAGE
CREASER MyBinding.com 5500 NE Moore Court Page 9 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 10 of 30

7-03-14 FEED BED ASSEMBLY
in 2 Posns. in 2 Posns. in 2 Posns. in 3 Posns. 15 11 14 26 3 7 13 28 22 16 28 23 12 29 31 37
21
25
20 34
8
1
19
17 35 9 30 in 2 Posns.
5 33 in 2 Posns. 10 6
36 18 32 2
4 28 27 in 2 Posns. in 6 Posns.
MyBinding.com Page 10 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 11 of 30

AutoCreaser Pro 50 FEED BED ASSEMBLY 7-03-14 ITEM No. PART No. QTY. DESCRIPTION 1 73-05-06 1 CHOKE BLEED ASSEMBLY - AutoCreaser50 2 73-06-02 1 VACUUM DRUM DRIVE ASSY. - AutoCreaser Pro 3 73-07-01 1 VACUUM ROLLER ASSY. - AutoCreaser 50 Mk4. 4 175-28-01 1 Butterfly Valve - Stepper 5 73-004 2 Key Hole Latch - Creaser 6 73-009-02 1 FEED BED SPACER - Foam. 7 73-012-02 1 BELT SUPPORT - AutoCreaser 50. 8 73-054-01 1 SUPPORT PLATE - AutoCreaser 50 9 73-066-01 1 KNOB - Vac Bleed 10 73-071-01 1 FEED FRAME - AutoCreaser 50 Mk4. 11 73-075-01 1 FEED DRUM ASSEMBLY - Idler 12 73-077-01 1 VACUUM DRUM MOUNTING - AC50 Mk4. 13 73-080-01 1 MANIFOLD PLATE - AutoCreaser 50 Mk4. 14 93-021 1 Feed Belt 15 93-032 1 Feed Drum Assy - Drive 16 93-033-02 1 Support Bracket - Control Bed - M3 17 94-021 1 LABEL - Papergate 'UP'. 18 51-095 1 Clamp Washer 19 28-003 1 UNIVERSAL KNOB ASSY - M6 x 25 Lg. - Black - Ø16 20 601-015 1 Snap Bushing Ø33.3 x Ø38 21 604-062 1 Waved Washer 22 607-017 1 TIMING BELT - 120 XL - 037 23 609-008 1 'O' Ring. 24 609-030 1 'O' Ring. 25 615-035 2 Metric Push-in Fix 26 401-02-040-006 1 Screw - Pan Pozi Taptite - M4 x 6 Lg. 27 401-02-040-008 7 Screw - Pan Pozi Taptite - M4 x 8 Lg. 28 401-02-040-016 6 Screw - Pan Pozi Taptite - M4 x 16 Lg. 29 401-02-050-020 2 Screw - Pan Pozi Taptite - M5 x 20 Lg. 30 402-02-040-008 2 Screw - Csk Hd. Taptite - M4 x 8 Lg. 31 403-01-040-008 5 SCREW - Socket Cap Head - M4 x 8 Lg. 32 403-01-060-012 1 Screw - Socket Cap Head - M6 x 10 Lg. 33 405-01-060-006 2 Screw - Button Hd. - M6 x 6 Lg. 34 408-01-050-030 1 Screw Skt Cone Pt - M5 x 30 Lg. 35 409-01-040-012 1 Screw - Skt Set Screw - Flat Pt. - M4 x 12 Lg. 36 461-01-060 1 Nut - Full - M6 37 481-040 5 WASHER - Plain - M4
MyBinding.com CREASER 5500 NE Moore Court Page 11 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 12 of 30

730820T FINAL ASSEMBLY
35 71 37 44 71 51 36 71
2 off 51 6 48 61 41
19
48 4 3
2 off 69 17
3 off
61 27 5 59 50 2 off 2 off 70 2 off 60 28 55 22 20 67 2 off 75 2 off 76 2 off
34
24 33 72
68
52
47 82 62 16 60 25 52 9 26 60 6 off 12 off 4 off
MyBinding.com Page 12 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 13 of 30

AutoCreaser Pro 50 FINAL ASSEMBLY ITEM No. PART No. QTY. DESCRIPTION 3 7-06-13 1 CREASING UNIT ASSEMBLY - Autocreaser Pro 50 4 7-08-13 1 Slotted Stacker Assy - Autocreaser Pro 50 5 71-011 1 HINGE PLATE - AutoCreaser. 6 71-012-02 2 COVER BRACKET - Mk2. 9 73-08-01 1 MANIFOLD TUBE ASSEMBLY - AutoCreaser Pro 50 16 75-01-07 1 CONTROL SYSTEM - AutoCreaser Pro 50 17 75-06-02 1 Touch Screen Assembly - 7” (New Controller) 19 75-253 1 Label - Reverse Gap Set 20 75-356 1 DIN Socket Assy. 22 75-333-01 1 EMC BLANKING PLUG - Eng. Socket. 24 75-387 1 Label - Fuse Ratings 25 75-411-01 1 COMPRESSOR PANEL - Autocreaser Pro 50 26 75-413-01 1 SERVICE PANEL - AutoCreaser Mk4. 27 75-414-02 1 TOP COVER - Touch Screen 28 75-428-01 1 Ethernet Bracket 33 76-041 1 CORD PULLEY - Driven. 34 76-042 1 DRIVE BELT - Feed Bed. 35 76-049-03 1 HINGE SHAFT - Wide 36 76-050-04 1 ENTRY GUARD - Wide 37 76-051-03 1 EXIT GUARD - Wide 41 96-053 1 Label - Roller Tilt 44 123-059 1 Label - Safety Warnings 47 601-080 1 Grommet Ø28.6 X Ø22 X Ø34.9 X 3.2 PVC 48 601-111 1 Tapered Ferrule 50 605-055 2 WASHER - Self Aligning 51 605-056 2 THRUST WASHER - Ø12.7 x Ø8.00 x 0.81 52 606-010 2 M6 Knurled Knoblet 55 613-351 1 MICROSWITCH 59 651-121 1 Connector - Ethernet 60 401-02-040-006 17 Screw - Pan Pozi Taptite - M4 x 6 Lg. 61 401-02-040-008 11 Screw - Pan Pozi Taptite - M4 x 8 Lg. 62 401-02-040-010 6 Screw - Pan Pozi Taptite - M4 x 10 Lg. 67 403-01-030-020 2 SCREW - Socket Cap Head - M3 x 20 Lg. 68 403-01-100-012 1 Screw - Socket Cap Head - M10 x 12 Lg. 69 405-01-060-012 4 SCREW - Socket Button Head - M6 x 12 Lg. 70 405-01-080-016 2 SCREW - Socket Button Head - M8 x 16 Lg. 71 406-01-040-006 6 SCREW - Tamperproof - M4 x 6 Lg 72 409-01-050-005 1 Screw - Skt Set Screw - Flat Pt. - M5 x 5 Lg. 75 464-01-030 2 NUT - NYLOC - M3 76 481-030 2 WASHER - Plain - M3 82 75-485-01 1 HOSE - MANIFOLD TUBE
MyBinding.com CREASER 5500 NE Moore Court Page 13 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 14 of 30

730820T FINAL ASSEMBLY
MyBinding.com Page 14 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 15 of 30

AutoCreaser Pro 50 FINAL ASSEMBLY ITEM No. PART No. QTY. DESCRIPTION 1 7-01-18 1 MAIN FRAME ASSEMBLY - AutoCreaser Pro 50 2 7-03-14 1 FEED BED ASSY - AutoCreaser Pro 50 7 71-020 1 LOCKING STUD - Clamp 8 71-025 1 Tilt Washer 10 73-072-01 1 SUPPORT BRACKET - Feed Bed - Autocreaser Pro 50 11 74-001-05 1 FEED BED - AutoCreaser Pro 50 12 74-002-02 1 Control Bed 13 74-003 1 BALL HOLDER - AutoCreaser. 14 74-01-14 1 Moving Sidelay - Autocreaser Pro 50 15 74-050-04 1 Loading Table - AutoCreaser Pro 50 18 74-462-01 1 LABEL - Autocreaser Pro 50 21 76-272 1 PSU - SWITCHED MODE - ATX12V - 300W 23 173-020 1 LABEL - Air Seperation 38 94-026 2 CLAMP KNOB - Sidelay. 39 94-028 2 LOCK PIN ASSEMBLY. - Side Lay. 40 94-058 1 BACKSTOP ASSEMBLY - Screw Clamped. 42 96-060 1 LABEL - Lock 43 98-013-03 1 ANTI-STATIC STRIP - Wide 45 172-05-02 1 PAPER GATE ASSY. - Indexing - AutoCreaser 50. 46 173-020-01 1 PSU Mounting Bracket 49 605-043 2 THRUST WASHER - Ø5.1 x Ø9.5 x 0.75 53 606-035 1 LOBE KNOB - Female - M8 54 609-009 1 EDGING STRIP 56 613-388 2 TIE WRAP - Long 57 617-003 5 STEEL BALL - Ø20 58 650-028 7 CABLE TIE MOUNTING - Push Fit 60 401-02-040-006 17 Screw - Pan Pozi Taptite - M4 x 6 Lg. 61 401-02-040-008 29 Screw - Pan Pozi Taptite - M4 x 8 Lg. 63 401-02-040-016 4 Screw - Pan Pozi Taptite - M4 x 16 Lg. 64 401-02-050-020 2 Screw - Pan Pozi Taptite - M5 x 20 Lg. 65 401-04-006-312 4 Screw - Pan Pozi UNC Taptite #6-32 x 5/16” Lg. 66 402-02-030-008 14 Screw - Csk Hd. Taptite - M3 x 8 Lg. 69 405-01-060-012 4 Screw - Socket Button Head - M6 x 12 Lg. 73 415-01-080-012 3 Screw - Hexagon Head - M8 x 12 Lg. 74 461-01-060 2 NUT - Full - M6 77 481-060 2 WASHER - Plain - M6 78 481-080 3 WASHER - Plain - M8 79 75-482-01 1 HOSE - INLET 80 75-483-01 1 HOSE - EXHAUST 81 75-484-01 1 HOSE - VALVE - BLOW 82 75-485-01 1 HOSE - MANIFOLD TUBE 83 75-486-01 1 HOSE - VALVE - VACUUM
MyBinding.com CREASER 5500 NE Moore Court Page 15 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 16 of 30

730820T FINAL ASSEMBLY
MyBinding.com Page 16 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 17 of 30

AutoCreaser Pro 50 FINAL ASSEMBLY
MyBinding.com CREASER 5500 NE Moore Court Page 17 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 18 of 30

730820T FINAL ASSEMBLY
4
2
11
7
3 5
8 1
9 12
Line on this side
6
10
ITEM No. PART No. QTY. DESCRIPTION 1 172-06-01 1 PIVOT ASSEMBLY - Papergate. 2 172-025-02 1 POST - Indexing Papergate - AutoCreaser. 3 172-028-02 1 COLLAR - indexing Papergate. 4 172-029-01 1 LOCKING NUT - Paper Gate 5 172-031-01 1 Label - Papergate 6 48-005-04 1 ROTARY PAPERGATE - Indexed. 7 601-162 1 M6 Ball Spring Plunger 8 604-068 1 WAVED WASHER. 9 615-006 1 CIRCLIP - Internal - Ø22 10 404-01-050-010 1 SCREW - Socket Csk Head - M5 x 10 Lg. 11 409-01-030-010 1 Screw - Skt Set Screw - Flat Pt. - M3 x 10 Lg. 12 411-01-040-005 1 SCREW - Skt Set Dog Pt. - M4 x 5 Lg.
PAPER GATE ASSEMBLY (172-05-02)
MyBinding.com Page 18 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 19 of 30

AutoCreaser Pro 50
BLANK PAGE
MyBinding.com CREASER 5500 NE Moore Court Page 19 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 20 of 30

7-06-13 CREASER UNIT
14 1 35 36 14 13 3 2 31 2 3 13 24 8
6
73
65
6 25 63 76 18 67 67 70 70 5 30 42 42 SEE PAGE 24 10 SEE PAGE 26 41 8 67 70 16 4 16 67 70 12
22
7 9 29 12 11 45 21 54 27 28 23 26 33 1 1 19 20 17 15 SEE PAGE 25 77 66 66 2 off. 69
MyBinding.com Page 20 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 21 of 30

AutoCreaser Pro 50 CREASER UNIT 7-06-13 ITEM NO. PART NUMBER QTY. DESCRIPTION 1 76-003-02 3 TIE BAR - AutoCreaser - Wide. 2 76-011 2 BLADE ADJUSTMENT CAM. 3 76-012 2 ADJUSTMENT DISK - AutoCreaser 4 76-034-06 1 TIMING PULLEY - 16XL (Wide) - Flanged - Short Hub. 5 76-04-02 1 SPLASH GUARD ASSEMBLY - AutoCreaser 50. 6 76-047 2 LOCK NUT - Blade Cam. 7 76-05-01 1 IDLER GEAR ASSEMBLY. 8 76-053-02 2 HINGE PILLAR 9 76-054-03 1 TILT PILLAR - AutoCreaser MK3 10 76-06-02 1 CRANK SHAFT ASSEMBLY - AutoCreaser 50 11 76-062-04 1 STEPPER PINION - 20T AutoCreaser 50 12 76-065 2 STEPPER SHIM. 13 76-101 2 LABEL - Blade Adjustment 14 76-105 2 BUFFER - Exit Guard. 15 76-121-01 1 MTG. PLATE - Stepper Motor. 16 76-122-01 2 TIE BAR - Female. 17 76-123-01 1 TIMING PULLEY - 20XL - Wide Flanged. 18 76-138-02 1 HUB ASSY. - Gap Control - Lay Side. 19 76-143-01 1 Gap Control Shaft 20 76-144-02 1 Female Tie Bar - Single Gap Control (Wide) 21 76-148-01 1 GAP SET LEVER ASSY. - Op. Side. 22 76-148-02 1 GAP SET LEVER ASSY. - Lay. Side. 23 76-149-01 1 Locking Link - Gap Control 24 76-154 1 LEAD - Dual Sensor Assy. 25 76-155 1 LEAD - Paper Jam Sensor. 26 76-150-01 1 Locking Knob - Gap Control 27 76-175-02 1 INPUT ROLLER - Lower - AutoCreaser 50. 28 76-177-02 1 INPUT ROLLER -Upper - AutoCreaser 50. 29 76-179-01 1 SIDE PLATE ASSEMBLY - Op. Side. 30 76-180-01 1 SIDE PLATE ASSEMBLY - Lay Side. 31 76-230-02 1 LEAD - Paper Guide Sensor - Wide. 33 76-240 1 STEPPER DRIVE MOTOR & LEAD ASSY. 35 76-250-02 1 Upper Output Shaft Assy - AC50 36 76-251-02 1 Lower Output Shaft Assy - AC50. 41 56-003-02 1 TIMING PULLEY Wide - 16XL - Flanged. 42 56-004-02 2 TIMING PULLEY - 16XL - Un-Flanged. 45 603-078 1 SPIROL SPACER - Ø10 X Ø13 X 6.5 Lg. 54 615-038 1 RETAINING RING - External - Ø35 63 403-01-080-012 2 Screw - Socket Cap Head - M8 x 12 Lg. 65 405-01-080-020 1 Screw - Button Hd. - M8 x 20 Lg. 66 407-01-050-006 3 Screw - Socket Set Knurled - M5 x 6 Lg. 67 409-01-040-004 3 Screw - Socket Set - Flat Point - M4 x 4 Lg. 69 409-01-050-005 1 Screw - Socket Set - Flat Point - M5 x 5 Lg. 70 411-01-040-006 4 Screw - Socket Set - Dog Point - M4 x 6 Lg. 73 462-01-080 1 Half Nut - M8 76 481-080 17 Washer - Plain - M8 77 481-100 1 Washer - Plain - M10
MyBinding.com CREASER 5500 NE Moore Court Page 21 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 22 of 30

7-06-13 CREASER UNIT
2 off 68 61 40 38 37 37 51 32 51
44 48 48 48 48
in 4 Posns. 59
48
48
55 48 39 61 68 in 4 Posns.
58 74 58 47
47 53 58
64 64 76
48 76 72
50 56 57
43
34
71 75 62 76 72 76 72 in 3 Posns.
75 60 43 52 49 52 46
MyBinding.com Page 22 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 23 of 30

AutoCreaser Pro 50 CREASER UNIT 7-06-13 ITEM NO. PART NUMBER QTY. DESCRIPTION 32 76-237-02 1 BLADE SET - Standard - Autocreaser 50. 34 76-241 1 STEPPER DRIVE MOTOR & LEAD ASSY. 37 78-013 2 PERFORATOR STRIPPER ASSEMBLY. 38 78-060-01 1 PERF. SHAFT SUPPORT BLOCK ASSY - Top. 39 78-060-02 1 PERF. SHAFT SUPPORT BLOCK ASSY - Bottom 40 78-062-01 1 ECCENTRIC Perf Shaft - Top. 43 601-124 2 HOLE BUSHING - Split - Ø19. 44 603-046 2 Spirol Pin - Ø4 x 12 Lg. 46 603-093 1 SPIROL SPACER - Ø10 X Ø13 X 12 Lg. 47 604-071 2 WAVED WASHER - Ø21.0 X Ø27.5 X 3.0 48 605-052 8 SUPPORT WASHER - Ø12 49 607-042 1 TIMING BELT - 160XL - 15. 50 607-048 1 TIMING BELT 51 608-019 2 Shoulder Bolt - Ø12(M10) x 30 Lg. 52 613-027 3 TIE WRAP - Small. 53 613-339 1 CABLE TIE MOUNTING 55 615-067 1 RETAINING RING - External - Ø30 56 651-031 1 TERMINAL STRIP - 45° - Single 57 401-02-040-006 1 Screw - Pan Pozi Taptite - M4 x 6 Lg. 58 401-02-040-008 24 Screw - Pan Pozi Taptite - M4 x 8 Lg. 59 401-02-040-016 4 Screw - Pan Pozi Taptite - M4 x 16 Lg. 60 403-01-050-016 1 Screw - Socket Cap Head - M5 x 16 Lg. 61 403-01-050-020 3 Screw - Socket Cap Head - M5 x 20 Lg. 62 403-01-050-025 7 Screw - Socket Cap Head - M5 x 25 Lg. 64 403-01-080-020 7 Screw - Socket Cap Head - M8 x 20 Lg. 68 409-01-040-006 2 Screw - Socket Set - Flat Point - M4 x 6 Lg. 71 461-01-050 7 Nut - Full - M5 72 461-01-080 7 Nut - Full - M8 74 481-040 4 WASHER - Plain - M4 75 481-050 15 Washer - Plain - M5 76 481-080 17 Washer - Plain - M8
MyBinding.com CREASER 5500 NE Moore Court Page 23 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 24 of 30

7-06-13 CREASER UNIT
MyBinding.com Page 24 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 25 of 30

AutoCreaser Pro 50 CREASER UNIT 7-06-13
MyBinding.com CREASER 5500 NE Moore Court Page 25 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 26 of 30

7-06-13 CREASER UNIT
MyBinding.com Page 26 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 27 of 30

AutoCreaser Pro 50 CREASER UNIT 7-06-15
MyBinding.com CREASER 5500 NE Moore Court Page 27 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 28 of 30

7-08-13 STACKER ASSEMBLY
1 6
2 4
3 7 1
5 2
8 11 12
10
14 13
9
View on Rear of Stacker
MyBinding.com Page 28 5500 NE Moore Court PAPER Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 29 of 30

AutoCreaser Pro 50 STACKER ASSEMBLY 7-08-13
ITEM NO. PART NUMBER QTY. Description 1 78-008 2 Magnetic Pad 2 78-009-03 2 Magnetic Strip 3 78-017-01 1 Stacker Bed 4 78-031-02 1 Stacker Guide - LH - Screened 5 78-032-01 1 Stacker Guide RH 6 78-033-01 1 Stacker Backstop - LH 7 78-033-02 1 Stacker Backstop - RH 8 78-034-01 1 Actuator Mounting Block 9 16-029-02 1 Hoop Strut - Conveyor 10 601-079 1 Magnet 11 601-174 3 Grub Screw - Slotted Nylon M4 x 6 Lg. 12 402-02-050-010 2 Screw - Csk Hd. Taptite - M5 x 10 Lg. 13 78-073-01 1 Guide Stop - Stacker 14 403-01-030-006 1 Screw - Socket Cap Head - M3 x 6 Lg.
MyBinding.com CREASER 5500 NE Moore Court Page 29 Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 30 of 30 · End of manual
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Not sure the part matches the machine | Model number differs from the specification plate | Confirm the model number is identical to the number stamped on the specification plate, and note the serial number stamped there too. Page 3 |
| Unsure how to identify a part for ordering | Assembly information was not quoted | Quote the major assembly number and description listed at the top of the page when ordering parts or seeking technical advice. Page 3 |
| Part is not available individually | It forms part of a sub-assembly that needs specialist tools and knowledge to dismantle | Order the sub-assembly. The machine may not perform correctly if you attempt to repair sub-assemblies of this type. Page 3 |
| Cannot find the right section | Parts are split across assemblies | Use the contents: Main Assembly 7-01-18 (page 6), Feed Bed Assembly 7-03-14 (page 10), Final Assembly 730820T (page 12), Creaser Unit 7-06-13 (page 20) and Stacker Assembly 7-08-13 (page 28). Page 5 |
| Wrong blower ordered | Blower SV190 differs by frequency | Order 621-032 for 50Hz or 621-038 for 60Hz. Page 8 |
| Need the right fastener | Screws are listed by type and length | Match the screw by description and length, for example 401-02-040-006, Screw Pan Pozi Taptite M4 x 6 Lg (item 38, quantity 4). Page 8 |
The major assembly number and description printed at the top of the parts page. Always quote it when ordering parts or asking for technical advice. Also confirm that your model number matches the one on the specification plate, and note the serial number (page 3).
Both are stamped on the machine's specification plate. The manual's model number, 730820T, is printed at the top of the contents page (page 3, page 5).
They mark sub-assemblies. The other listed items are available individually as spare parts. Some components are only sold as part of a sub-assembly, because taking them apart may need special tools and knowledge (page 3, page 4).
7-01-18 Main Assembly, 7-03-14 Feed Bed Assembly, 730820T Final Assembly, 7-06-13 Creaser Unit and 7-08-13 Stacker Assembly (page 5).