

Page 1 of 36

Text on page 2
AutoFold Pro
DOCUMENT FOLDING MACHINE
ILLUSTRATED PARTS MANUAL
ISSUE 6
SEPTEMBER 2011
Page 2 of 36

Text on page 3
INTRODUCTION
AutoFold Pro
ILLUSTRATED PARTS MANUAL
The Illustrated Parts Manual has been designed to assist when selecting a part or assembly which may be required to service or repair your machine.
The index on page four lists all of the major assemblies in the order in which the machine is constructed.
The following page demonstrates how to recognise a part from a sub-assembly and shows the quantity contained within the major assembly.
The major assembly number and description is listed at the top of the page and should always be quoted when ordering parts or when seeking technical advice.
Before ordering parts confirm that the model number of the machine (listed at the top of page four) is identical to the number stamped on the specification plate. Whilst checking this, make a note of the serial number also stamped on the plate.
Some components will not be made available individually as they form part of a sub-assembly which may require specialist tools and knowledge to dismantle. The machine may not perform correctly if attempts are made to repair sub-assemblies of this type.
NOTE....
ALWAYS READ THE OPERATORS MANUAL BEFORE MAKING ANY
ADJUSTMENTS TO YOUR MACHINE AND ALWAYS DISCONNECT THE POWER
SUPPLY BEFORE REMOVING ANY COVERS.
FOLDING
Page 3 of 36

Page 4 of 36

Text on page 5
INDEX
SECTION
ASSEMBLY
DESCRIPTION
MAIN FRAME ASSEMBLY
MECHANISM
DELIVERY SYSTEM
FINAL ASSEMBLY
PAGE
FOLDING
Page 5 of 36

Text on page 6
AutoFold Pro
BLANK
PAGE
SYSTEM
Page 6 of 36

Text on page 7
MAIN FRAME ASSEMBLY
FOLDING
Page 7 of 36

Text on page 8
AutoFold Pro
SYSTEM
MAIN FRAME ASSEMBLY
PART No. QTY. 181-001-01 181-001-02 181-004-01 181-003-01 181-010-01 183-015-01 183-020-01 183-022-01 186-001-05 186-002-02 186-004-01 186-006-01 175-053-06 175-054-01 175-134-01 178-052-02 141-003-01 141-003-07 76-105 76-300 76-301 75-512 62-006 02-019 601-015 601-076 602-156 602-192 604-108 613-339 651-101 680-009 401-02-040-008 401-02-040-016 403-01-050-016 403-01-080-012
- -
- 403-01-080-020 403-01-080-025 408-01-050-010 415 - 01 - 030 - 040 461 - 01 - 040 462 - 01 - 080 464 - 01 - 030 481 - 030 481 - 040 481 - 050 481 - 080 481 - 100 485-040 186-001-03 401-02-050-008
DESCRIPTION
MAIN PLATE - Op Side MAIN PLATE - Lay Side Baffle Plate Wheel Shaft BEARING HOUSING ASSY. - Op Side Front Panel - Feed End Mounting Bracket - Entry Guard TAB - Front Panel Gas Strut Eye - Ø12 x M8 Gas Strut Eye Bearing Clamp Plate - Mono Studded Location Plate - Feed System BLADE GUIDE - Top BLADE GUIDE - Lower HEX PILAR - M8 Action Shaft - Gas Strut Tie Bar - Mk5 Female Tie Bar - Entry Guard BUFFER - Exit Guard STEPPER DRIVE MOTOR & LEAD ASSY. STEPPER DRIVE MOTOR & LEAD ASSY. ANTI-STATIC TRANSFORMER ASSY. - 230V - UL NYLON WHEEL Collar Snap Bushing Ø33.3 x Ø38 Snap Bushing Ø15.5 x Ø19 Flanged Oilite Bush BEARING - Iglidur W300 GAS STRUT - Feed Bed CABLE TIE MOUNTING Mains Inlet - 20A Mains Filter Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 16 Lg. SCREW - Socket Cap Head - M5 x 16 Lg. SCREW - Socket Cap Head - M8 x 12 Lg. SCREW - Socket Cap Head - M8 x 20 Lg. SCREW - Socket Cap Head - M8 x 25 Lg. SCREW-SOCKET SET CONE PT. - M5 X 10 LG H ex Hd . Set screw - M3 x 40 L g. NUT - Full - M4 NUT - Half - M8 NUT - NYLOC - M3 WASHER - Pl a i n - M3 WASHER - Pl a i n - M4 WASHER - Pl a i n - M5 WASHER - Pl a i n - M8 WASHER - Pl a i n - M10 WASHER - Shakeproof - M4 Gas Strut Eye - Ø8 x M8 Screw - Pan Pozi Taptite - M5 x 8 Lg.
Page 8 of 36

Text on page 9
MAIN FRAME ASSEMBLY
FOLDING
Page 9 of 36

Text on page 10
AutoFold Pro
SYSTEM
MAIN FRAME ASSEMBLY 181-01-01
PART No. QTY. 181-010-02 183-020-01 186-001-04 186-001-05 186-002-02 186-004-01 186-006-01 181-006-01 171-019-03 175-053-06 175-054-01 175-198-01 175-202-01 76-213-05 601-076 602-156 602-190 602-192 604-108 401-02-040-008 401-02-040-016 403-01-050-012 403-01-050-016 403-01-080-012 403 - 01-080-020
- -
- 403-01-080-025 409-01-050-006 462 - 01 - 080 481 - 080 481 - 100 407-01-050-006
DESCRIPTION
BEARING HOUSING - Lay Side Mounting Bracket - Entry Guard Gas Strut Eye - Ø 8 x M8 Gas Strut Eye - Ø12 x M8 Gas Strut Eye Bearing Clamp Plate - Mono Studded Location Plate - Feed System HEX PILLAR - M8 Motor Retention Plate BLADE GUIDE - Top BLADE GUIDE - Lower HEX SPACER - Cam Pulley Support Plate TIMING PULLEY - 25XL - Wide Flanged TIMING PULLEY - 16XL - Wide Flanged Snap Bushing Ø15.5 x Ø19 Flanged Oilite Bush Flanged Iglidur Bush - Ø10 x Ø12 x Ø18 x 5 BEARING - Iglidur W300 GAS STRUT - Feed Bed Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 16 Lg. SCREW - Socket Cap Head - M5 x 12 Lg. SCREW - Socket Cap Head - M5 x 16 Lg. SCREW - Socket Cap Head - M8 x 12 Lg. SCREW - Socket Cap Head - M8 x 20 Lg. SCREW - Socket Cap Head - M8 x 25 Lg. SCREW - Socket Set Screw - Flat Pt. - M5 x 6 Lg. NUT - Half - M8 WASHER - Pl a i n - M8 WASHE R - Pl a i n - M10 SCREW - Socket Set Screw - Knurled Pt - M5 x 6 Lg.
Page 10 of 36

Page 11 of 36

Text on page 12
AutoFold Pro
MECHANISM
QTY.
DESCRIPTION
MAIN FRAME ASSEMBLY - Autofold
Support Stud Jam Detector (Emitter) Assy Jam Detector (Receiver) Assy Lower Input Roller Assy - Driven Drive Idler Assy FIXED ROLLER ASSY. FIXED ROLLER ASSY. - 1st FIXED ROLLER ASSY. - 2nd FIXED ROLLER ASSY. - 3rd
Roller Shield Assy. - Lower Latch - Op Side Latch - Lay Side Edge Sensor Assembly 2nd Blade Assembly 1st Blade Assembly
Paper Guide Assy - Dynamic - Extended
Crank Shaft Assy - Cam Drive INPUT ROLLER ASSEMBLY - Upper ROLLER SHIELD - 2nd
KNIFE DRIVE HUB ASSY - 2nd Roller - Op Side KNIFE DRIVE HUB - 1st Roller - Lay Side Worm Wheel - Eccentric
CRANK DISC ASSY. - Op Side
EXTENDED KNIFE DRIVE PIN
Link RETAINING RING- External - Ø25
Anti - Static Spyder Bar - Stud Fixing Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M5 x 20 Lg. SCREW - Socket Cap Head - M8 x 16 Lg. SCREW - Socket Cap Head - M8 x 20 Lg.
Screw - Skt Set Screw - Flat Pt. - M4 x 6 Lg. Screw - Skt Set Screw - Flat Pt. - M5 x 6 Lg. Screw - Skt Set Dog Pt. - M5 x 10 Lg. NUT - Full - M6 WASHER - Pl a i n - M6 WASHER - Plain - M8 COLLAR - Top Roller WASHER - Plain - M4
SENSOR BAR ASSEMBLY SENSOR BAR ASSEMBLY
KNOB - Support Stud
SYSTEM
Page 12 of 36

Text on page 13
MECHANISM
3 off
SEE PAGE 22
SEE PAGE 20
FOLDING
Page 13 of 36

Text on page 14
AutoFold Pro
SYSTEM
MECHANISM
QTY.
DESCRIPTION
Feed System Assembly - Long Feed System Assembly - Short Support Stud Control System - Op Side Gap Set Assembly Connecting Link Assembly Knife connecting Link Assembly
Door Ramp Screw - Pan Pozi Taptite - M4 x 12 Lg. Screw - Pan Pozi Taptite - M4 x 20 Lg. Screw - Pan Pozi Taptite - UNC - #6-32 x 5/16” Screw - Socket Cap Head - M5 x 20 Lg. Screw - Socket Cap Head - M8 x 12 Lg. Screw - Socket Button Head - M4 x 10 Lg. WASHER - Plain - M5 WASHER - Plain - M6
PSU - SWITCHED MODE - ATX12V - 300W
KNOB - Support Stud
Page 14 of 36

Text on page 15
MECHANISM
SEE PAGE 21
FOLDING
Page 15 of 36

Text on page 16
AutoFold Pro
MECHANISM
QTY.
DESCRIPTION
Control System - Lay Side
Cable Strap Cam Pulley Support Plate Assembly
SHIELD SUPPORT - Top - Op.
SPACER
CRANK DISC ASY. - Lay Side
BLADE POSITION SENSOR
THRUST WASHER - Ø6.6 x Ø11.1 x 1.19 180XL Timing Belt
Shoulder Bolt - Ø6 (M5) x 12 Lg. CIRCLIP - External - Ø20
Screw - Pan Pozi Taptite - M3 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg.
Screw - Socket Cap Head - M8 x 16 Lg.
Screw - Socket Button Head - M4 x 10 Lg. WASHER - Plain M6
SYSTEM
Screw - Pan Pozi Taptite - M4 x 12 Lg.
WASHER - Plain M8
SUPPORT WASHER - Ø12
Nylon Pillar - M4M - M4F x 40 Lg.
Page 16 of 36

Text on page 17
MECHANISM
182-01-01 (Feed System Assy. - Long)
FOLDING
Page 17 of 36

Text on page 18
AutoFold Pro
MECHANISM
QTY.
DESCRIPTION
Feed Bed Frame - Long Side Lay Frame - Long Feed Bed - Short Paper Guide - Long Lower Paper Guide - Long Upper Rear Input Panel - Anti-Static Tie Bar - Feed Frame Input Guide Belt Roller Shaft - Idler
Belt Roller Shaft - Drive Belt - Paper Transport - Long
Belt - Paper Transport - Medium Belt - Paper Transport - Short
Cord Drive Spacer Input Table Conduit Spacer - Input Guide Vac Relief Flap
Support Disk Bracket - Symetric - Rear Panel Alignment Plate Cable Entry Plate Support Tube Support Bush - Flanged Fan and Support Assembly - Long Cord Drive Assembly Cord Idler Assembly - Standard Cord Idler Assembly - Short Belt Support Roller Assembly LEAD - Autofold / Autocreaser Link Grommet Thrust Washer - Ø8 x Ø15.88 x 0.79 Nylon Washer - Ø15 x Ø21 x 1 Delivery Grab Handle Strain Relief Bush Tie Wrap - Long Anti - Static Spyder Bar - Female Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 10 Lg. Screw - Csk Hd. Taptite - M3 x 8 Lg. Screw - Socket Cap Hd. - M6 x 10 Lg. Screw - Socket Cap Hd. - M8 x 12 Lg. Screw - Skt Csk Hd. - Flat Pt. - M8 x 20 Lg. Screw - Skt Button Hd. - M5 x 10 Lg. Screw - Skt Button Hd. - M8 x 12 Lg. Earth Screw - Pan Pozi Taptite - M4 x 8 Lg. WASHER - Plain M4 WASHER - Plain M5 WASHER - Plain M6 WASHER - Plain M8
SYSTEM
Page 18 of 36

Text on page 19
MECHANISM
182-01-02 (Feed System Assy. - Short)
FOLDING
Page 19 of 36

Text on page 20
AutoFold Pro
MECHANISM
QTY.
DESCRIPTION
Feed Bed Frame -Short Side Lay Frame - Short Feed Bed - Short Paper Guide - Short Lower Paper Guide - Upper Rear Input Panel - Anti-Static Tie Bar - Feed Frame Input Guide Belt Roller Shaft - Idler
Belt Roller Shaft - Drive Belt - Paper Transport - Medium Belt - Paper Transport - Short
Cord Drive Spacer Input Table Conduit Spacer - Input Guide Vac Relief Flap
Support Disk Bracket - Symetric - Rear Panel Alignment Plate Cable Entry Plate Support Tube Support Bush - Flanged Fan and Support Assembly - Short Cord Drive Assembly Cord Idler Assembly - Standard Cord Idler Assembly - Short Belt Support Roller Assembly LEAD - Autofold / Autocreaser Link Grommet Thrust Washer - Ø8 x Ø15.88 x 0.79 Nylon Washer - Ø15 x Ø21 x 1 Delivery Grab Handle Strain Relief Bush Tie Wrap - Long Anti - Static Spyder Bar - Female Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Csk Hd. Taptite - M3 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 10 Lg. Screw - Csk Hd. Taptite - M3 x 8 Lg. Screw - Socket Cap Hd. - M6 x 10 Lg. Screw - Socket Cap Hd. - M8 x 12 Lg. Screw - Skt Csk Hd. - Flat Pt. - M8 x 20 Lg. Screw - Skt Button Hd. - M5 x 10 Lg. Screw - Skt Button Hd. - M8 x 12 Lg. Earth Screw - Pan Pozi Taptite - M4 x 8 Lg. WASHER - Plain M4 WASHER - Plain M5 WASHER - Plain M6 WASHER - Plain M8
SYSTEM
Page 20 of 36

Text on page 21
MECHANISM
184-01-01 (Control System - Op Side)
FOLDING
Page 21 of 36

Text on page 22
MECHANISM
184-02-01 (Control System - Lay Side)
SYSTEM
Page 22 of 36

Text on page 23
MECHANISM
QTY.
DESCRIPTION
Mounting Plate Pot & Lead Pot & Lead Assy. - Gap 1 Pot & Lead Pot & Lead Assy. - Gap 2 Pot & Lead Pot & Lead Assy. - Gap 3 Friction Plate Assy. - Short
Knob - Gap Set Shaft - Gap Set - 1st Roller Shaft - Gap Set - 2nd Roller Shaft - Gap Set - 3rd Roller Worm - Gap Set Collar
Thrust Washer - Ø8 x Ø15.88 x 0.79
DISC SPRING
MULTI-BEAM COUPLER - Size 13 Screw - Socket Set Knurled - M3 x 4 Lg. Screw - Socket Set Knurled - M4 x 4 Lg. Screw - Socket Set Knurled - M4 x 5 Lg. Screw - Socket Set Knurled - M4 x 6 Lg. Screw - Skt Set Dog Pt. - M4 x 6 Lg.
186-03-01 (Gap Set Assembly)
FOLDING
Page 23 of 36

Text on page 24
AutoFold Pro
SYSTEM
MECHANISM
Page 24 of 36

Page 25 of 36

Text on page 26
AutoFold Pro
SYSTEM
MECHANISM
Page 26 of 36

Page 27 of 36

Text on page 28
AutoFold Pro
DELIVERY SYSTEM
QTY.
DESCRIPTION
DO NOT TOUCH_LABEL
Small Stepper Driver PCB Assy. Roller Guide Bar Belt Clamp plate - Delivery D - Spacer - Belt Clamp Roller Pivot Shaft - Delivery COLLAR - Wheel Spacer. Positioning Pot Assy Idler Pulley Assy - Size 20 SPACER. Stacker Pivot Plate Stacker Lock Plate Delivery Roller Tie Bar Stacker Plate Clip Delivery Idler Roller Assy Delivery Drive Assy Driven Roller 3” Roller Guide Assy - Lay Side Roller Guide Assy - Op Side Delivery Main Frame Assy. Delivery Stepper Cover Inner Catch Tray Delivery - Undercover Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M5 x 16 Lg. SCREW - Cap Hd. - M4 x 8Lg. SCREW - Socket Cap Head - M5 x 35Lg. SCREW - Socket Button Head - M4 x 10Lg. SCREW - Socket Button Head - M4 x 16Lg. SCREW - Socket Button Head - M8 x 12Lg. Screw - Skt Set Screw - Flat Pt. - M4 x 6Lg. Screw - Skt Set Screw - Flat Pt. - M5 x 6Lg. NUT - Half - M12 NUT - NYLOC - M4 WASHER - Plain - M4 WASHER - Plain - M6 WASHER - Plain - M12 Square Foot - 12.6mm SPIROLSPACER - Ø4 x Ø5.65 x 4 Lg. Thrush Washer - Ø8 x Ø15.88 x 0.79 NYLON WASHER - Ø12.2 X 17.1 X 0.79
STRAIN RELIEF BUSH
WASHER - Plain - M5 Roller Guide Plate - Lay Side
SYSTEM
Page 28 of 36

Page 29 of 36

Text on page 30
AutoFold Pro
DELIVERY SYSTEM
QTY.
SYSTEM
DESCRIPTION
Delivery - Lay Side Delivery - Op. Side Conveyor Bed Tension Block - Dynafold HEX PILLAR - M8 x 30 Lg. STIFFENER - Delivery Conveyor Bed. Grab Handle Screw - Pan Pozi Taptite - M4 x 16 Lg. SCREW - Socket Button Head - M4 x 10 Lg. SCREW - Socket Button Head - M6 x 10 Lg. NUT - Full - M4 WASHER - Plain - M4 WASHER - Plain - M6
Page 30 of 36

Page 31 of 36

Text on page 32
AutoFold Pro
DELIVERY SYSTEM
QTY.
DESCRIPTION
GAS STRUT EYE. 385 Belt - 2 Ply - Paper Transport Tie Bar - Gas Spring - Digifold Mk2 Delivery End Cover Sheet Guide Tie Bar - Drive Assy Stepper Plate Assy - Op Side Stepper Plate Assy - Lay Side Delivery Beam Extension
Action Shaft- Beam Extension Crowned Drive Shaft Assy Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M5 x 12 Lg. SCREW - Socket Cap Head - M8 x 20 Lg. SCREW - Socket Countersunk Head - M8 x 20 Lg. Screw - Skt Set Screw - Flat Pt. - M6 x 25 Lg. Earthing Screw - Pan Pozi Taptite - M4 x 8 Lg.
NUT - Full - M4 NUT - Half - M6 WASHER - Plain - M8 M3 Washer Shakeproof- Ext Flanged Iglidur Bush - Ø12 x Ø16 x 10 100 XL Timing Belt 'O' Ring Ø8 x Ø3
CABLE TIE MTG. - Push Fit.
Delivery Connector & Lead Assembly
BELT DRIVE MOTOR ROLLER POSITION MOTOR
SYSTEM
Page 32 of 36

Text on page 33
DELIVERY SYSTEM
QTY.
DESCRIPTION
Crowned Roller Assy Crowned Roller Shaft Assy Roller Drive Pulley - 20XL CIRCLIP - External - Ø12 CIRCLIP - External - Ø10
BEARING - Deep Groove Ball - 6000-ZZ ‘O’ Ring Screw - Skt Set Screw - Flat Pt. - M4 x 4Lg.
178-06-02 (Crowned Drive Shaft Assy)
FOLDING
Page 33 of 36

Text on page 34
AutoFold Pro
DELIVERY SYSTEM
QTY.
DESCRIPTION
Bearing Plug - Idler Drum Extended Belt Drum - Idler Delivery Idler Shaft BEARING - Deep Groove Ball - 6001-ZZ RETAINING RING - External - Ø12
178-09-01 (Delivery Idler Roller Assy)
SYSTEM
Page 34 of 36

Text on page 35
FINAL ASSEMBLY
VIEW IN DIRECTION OF ARROW ‘X’
FOLDING
Page 35 of 36

Text on page 36
AutoFold Pro
ITEM No. PART No.
SYSTEM
FINAL ASSEMBLY
Description
QTY.
Rear Panel - With Access Door Column Assy - Op Side Column Assy - Lay Side Door Assembly - Lay Side Entry Guard Assy.
Dynafold Mechanism Delivery Assembly Door - Op Side Top Cover - Dynafold Top Cover - Op Side Door Shaft - Top Cover
WASHER - Plain - M3 Earth Screw - Pan Pozi Taptite - M4 x 8 Lg.
Label UL- Fuse Ratings - Autofold Pro Label - Anti-Static / Sharp Blades
Gap Set Label Label - Autofold Pro Label - Safety Warnings Touch Screen Assembly - 7” (New Controller) Handle - Pocket Pull Grommet Foot Gas Spring - Locking Microswitch Earth Label Screw - Pan Pozi Taptite - M3 x 16 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg.
Screw - Pan Pozi Taptite - M4 x 10 Lg. Screw - Csk Head. Taptite - M4 x 8 Lg. Screw - Socket Cap Head. - M3 x 30 Lg.
Screw - Socket Button Head. - M6 x 10 Lg. Screw - Tamperproof - M4 x 6 Lg.
NUT - NYLOC - M3
Page 36 of 36 ยท End of manual
Quick start
- Use the index to find the major assembly the part belongs to.
- Confirm the model number on your machine's specification plate matches the manual and note the serial number.
- Quote the major assembly number and description along with the part when ordering or asking for technical advice.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Not sure the parts list matches the machine | Model number not confirmed | Confirm the model number listed at the top of page four is identical to the number stamped on the specification plate. Note the serial number too. Page 3 |
| A part cannot be ordered on its own | Some components are part of a sub-assembly | Order the sub-assembly instead. Some components are not made available individually. Page 3 |
| Machine does not perform correctly after a repair | Repair was attempted on a sub-assembly that needs specialist tools and knowledge | Avoid repairing these sub-assemblies yourself and get the sub-assembly or technical advice. Page 3 |
| Technical advice or an order cannot be matched to a part | Major assembly number and description not given | Quote the major assembly number and description listed at the top of the page. Page 3 |
| Cover must be removed to reach a part | Power still connected | Disconnect the power supply before removing any covers. Page 3 |
| Not sure how a part relates to the others | Assemblies are listed in build order | Use the index on page four, which lists the major assemblies in the order the machine is constructed. Page 3 |
Frequently asked questions
What is the part number for the AutoFold Pro long feed system assembly?
The long feed system assembly is 182-01-01 and the short version is 182-01-02. See pages 17-19.
What is the part number for the gap set assembly?
The gap set assembly is 186-03-01. See page 23.
What are the control system assembly numbers?
Control System - Op Side is 184-01-01 and Control System - Lay Side is 184-02-01. See pages 21-22.
Which delivery sub-assemblies have their own numbers?
The crowned drive shaft assembly is 178-06-02 and the delivery idler roller assembly is 178-09-01. See pages 33-34.
