Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 1

Page 1 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 2
Text on page 2

Booklet Maker BM 61

Operator Manual

Morgana Systems Limited ▪ United Kingdom ▪ www.morgana.co.uk ▪ Telephone: ( 01908 ) 608888 ▪ Facsimile: ( 01908 ) 692399

Page 2 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 3
Text on page 3

BOOKLET MAKER BM 61

Operating Instruction Booklet Maker Reference

Part no: 61255 Doc no: T10185 Rev. date: 5 Apr 2013

Page 3 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 4
Text on page 4

When using this machine, following safety precautions should always be followed.

Notation conventions Whenever necessary, the following points for attention are indicated in this manual.

WARNING:

Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.

CAUTION:

Indicates a potentiality hazardous situation which, if instructions are not followed, may result in minor or moderate injury or damage to machine or property.

Note This sign refers to:

  • Remarks for making the operation much easier. You get practical hints or knowledge to assist you in the machine operation such as:
  • Preparations required before operating
  • How to prevent papers from being misfed or damaged
  • Precautions required or actions to take after misoperation
  • Limitations like numerical limits, functions that cannot be used together or conditions, under which a particular function cannot be used or obtained.
  • Information.

[ ] Keys that appear on the machine’s display panel.

WARNING:

Always connect the equipment to a properly grounded power source (wall outlet). If in doubt, have the power source checked by a qualified electrician. Improper grounding of the equipment can result in electrical shock. To avoid hazardous electric shock, do not remove any covers or screws other than those specified in this manual. Turn off the power and disconnect the power plug (by pulling the plug, not the cable) if any of the following conditions exists:

  • You drop objects or spill something into the equipment.
  • You suspect that your equipment needs service or repair.
  • Your equipment’s covers has been damaged.
  • You notice unusual noises or odours when operating the equipment.
  • If the power cable or plug becomes worn out or otherwise damaged
  • Before cleaning and care.
  • Before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equiment This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

The product (System) which is connected to this machine will be class A.

Note The domestic environment is an environment where the use of broadcast radio and television recievers may be expected within a distance of 10 m of the apparatus concerned.

Page 4 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 5
Text on page 5

TABLE OF CONTENTS

What You Can Do With This Machine............................................................................................. 5 Main Components............................................................................................................................ 6 General.......................................................................................................................................... 6 Infeed section, upper..................................................................................................................... 7 Infeed section, upper..................................................................................................................... 8 Control Panel................................................................................................................................. 9 Accessories (optional)................................................................................................................. 10

  1. Basics................................................................................................ 11

Turning On / Off the Power............................................................................................................ 11 Paper Settings................................................................................................................................ 12 Set up for non-standard paper sizes............................................................................................ 12 Reset to standard paper sizes..................................................................................................... 12

  1. Settings............................................................................................. 13

ON-line ............................................................................................................................................ 13 Stapling and folding..................................................................................................................... 13 Folding only................................................................................................................................. 13 OFF-line .......................................................................................................................................... 14 Stapling and folding .................................................................................................................... 14 Folding ........................................................................................................................................ 14 4.1.5 Block stapling - Option 1..................................................................................................... 15 4.1.6 Block stapling - Option 2..................................................................................................... 16

  1. Operation.......................................................................................... 17

Operating the bookletmaker.......................................................................................................... 17 Operating ON-line........................................................................................................................ 17 Operating OFF-line...................................................................................................................... 17

  1. Troubleshooting............................................................................... 19
  2. General remarks............................................................................... 21

Do’s And Don’ts.............................................................................................................................. 21 Placing Your Machine.................................................................................................................... 22 Machine Environment.................................................................................................................. 22 Power Connection....................................................................................................................... 22

  1. Specifications................................................................................... 23

Page 5 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 6

Page 6 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 7
Text on page 7

What You Can Do With This Machine

BM 61 stand alone unit

BM 61 against a collator/feeder 510

The BM 61 automatic Booklet Maker combines features from large and advanced systems into one compact unit designed to meet the highest demands for productivity, safety and ease of operation.

The BM 61 can be installed against a collator/feeder or run as a stand alone unit. The bookletmaker can be installed against ’s collator model 310/306 or against collator/feeder model 510.

Page 7 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 8
Text on page 8

Main Components

General

  1. Top cover
  2. Upper pressure roller assembly
  3. Press area, machine release
  4. Control panel
  5. Fold stop assembly
  6. Belt Stacker

(Only used for ON-line operation to Collator) (Press here and the Booklet Maker will be released from the Collator and can be rolled away)

Page 8 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 9
Text on page 9

Infeed section, upper

  1. Upper guide, side jogger
  2. Side jogger, rear
  3. Scale, paper length
  4. Rear jogger roller
  5. Side jogger, front
  6. Upper guide, side jogger
  7. Release handle, side jogger
  8. Scale, paper width
  9. Anvil
  10. Release handle, side jogger
  11. Scale upper pressure roller assembly

Page 9 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 10
Text on page 10

Infeed section, upper

  1. Positioning holes, small paper width (310/306:Used for A4/8½” paper widths or sizes nearby. 510: Not used.)
  2. Positioning holes, large paper width (310/306: Used for A3/11” paper widths or sizes nearby. 510: Used for all paper sizes)
  3. Positioning mark (green) (Shall correspond to the green mark on the Collator)
  4. Paper stop crank (Used for adjustment to correct paper length)
  5. Rear jogger latch (Used to lower the rear jogger and enable OFF-line operation)
  6. Rear jogger adjustment latch (Used to position the rear jogger to the paper length)
  7. Receptacle, connection cable (The connection cable from the Collator connects here)
  8. Knob, adjustment for odd paper size (By loosening the knob the Docking Bracket can be individually positioned for odd paper sizes)
  9. Docking Bracket

Page 10 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 11
Text on page 11

Control Panel

Power switch Low staples indicator Jam indicator * Stapling ON / OFF Folding ON / OFF Automatic start ON / OFF Automatic start SAFE MODE/ FAST MODE

  1. Time delay
  2. Manual start button

(Can only be used OFF-line) (Can only be used ON-line) (Can only be used OFF-line) (Can only be used OFF-line)

Page 11 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 12
Text on page 12

Accessories (optional)

Belt Stacker Adapter Delivery Tray Knob, Delivery Tray

(By loosening the knob the Delivery Tray can be adjusted for correct paper size)

Page 12 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 13
Text on page 13
  1. Basics

Turning On / Off the Power

Plug the power cord into the wall outlet and into the bookletmaker.

Set power switch (A) to 1 to turn on the power, if power on the green lamp (B) will lit.

To turn off the power set power switch (A) to 0, if power off the green lamp (B) will also be turned off

Page 13 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 14
Text on page 14
  1. Basics

Paper Settings

Set up for non-standard paper sizes

This procedure is to enable ON-line operation with paper sizes that deviate from the standard A4/A3 and 81/2“x11”/11”x17” sizes.

Perform the setup of the Booklet Maker for the paper size.

Attach the Booklet Maker to the Collator, using the positioning holes on tBookletMaker that best matches the paper size. (Green mark on rear side jogger as close as possible to the Docking Bracket).

Loosen the knob for adjustment to odd paper sizes on the Docking Bracket.

Move the Booklet Maker sidewise until the green mark on the rear side jogger is aligned with the green mark on the Collator.

Reset to standard paper sizes

Disconnect the Booklet Maker from the Collator by pressing the Docking Bracket (green marked side).

Loosen the knob for adjustment to odd paper sizes.

Slide the Docking Bracket back to align it with the chassis in the Booklet Maker, it will lock into place.

Page 14 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 15
Text on page 15
  1. Settings

ON-line

Stapling and folding

Open the top cover.

Set the two side joggers to the correct paper size according to the scale.

Insert a set to the stapling area.

Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.

Note When checking the alignment, do not squeeze the release handle, only push on top ofthe side jogger at the green label, to simulate the jogging action that the BM 61 does during run.

Turn the paper stop crank until the trail edge of the set is in line with the scale for paper length.

Move the rear jogger up against the trail edge of the set.

Position the upper pressure roller according to the scale.

Position the stapler heads over the anvils to be used.

  1. Attach the Booklet Maker to the Collator and make sure that the green mark on the Docking Bracket aligns with the green mark on the Collator.
  2. Set the stapling switch to ON position.
  3. Set the folding switch to ON position.
  4. Close the top cover.
  5. Set the power switch to ON position.

Folding only

Same procedure as above with the exception that on point 11 the switch is set to OFF position and point 9 is not performed.

Page 15 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 16
Text on page 16

OFF-line

  1. Settings

Stapling and folding

Remove the upper pressure roller assembly.

Flip over the side jogger upper guides (both side joggers).

Lower the rear jogger unit by pressing the rear jogger unit forward and downwards (green marked). Open the top cover.

Set the side jogger to the correct paper size according to the scale.

Insert a set into the stapling area.

  1. Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.

Note When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.

Turn the paper stop crank until the trail edge of the set is in line with the scale for paper length.

  1. Position the stapler heads over the correct anvils.
  2. Set the stapling switch to ON position.
  3. Set the folding switch to ON position.
  4. Close the top cover.
  5. Set the power switch to ON position.

Folding

Same procedure as the last one, with the exception that on point 11 the switch is set to OFF position and point 10 is not performed.

Page 16 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 17
Text on page 17

Lower the rear jogger by pressing the rear jogger unit forward (green marked).

Remove the upper pressure roller assembly.

Flip over the side jogger upper guides (both side joggers).

Open the top cover.

Set the side jogger to the correct paper size according to the scale.

Insert a set into the stapling area.

Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.

  1. Settings

4.1.5 Block stapling - Option 1

Note When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.

Turn the paper stop crank to position the set to the stapler.

  1. Position the stapler heads over the correct anvils.
  2. Close the top cover.
  3. Set the stapling switch to ON position.
  4. Set the folding switch to OFF position.
  5. Select manual or automatic start.
  6. Flip down the fold stop to enable the sets to pass through the machine.
  7. Set the power switch to ON position.

Note By using the adapter (optional) either the Belt Stacker or the Delivery Tray can be used for stacking of stapled sets.

Page 17 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 18
Text on page 18
  1. Settings

4.1.6 Block stapling - Option 2

Lower the rear jogger by pressing the rear jogger unit forward (green marked).

Remove the upper pressure roller.

Flip over the side jogger upper guides (both side joggers).

Open the top cover.

Set the side jogger to the correct paper size according to the scale.

Insert the two red pins in the holes in the side joggers. (The pins are stored inside the machine over the fold rolls). These will stop the set in the correct position (in this mode the set will not be transported through the machine).

Insert set into the stapling area.

Move the rear side jogger up against the paper to verify that the side jogger aligns the sheets.

Note When checking the alignment, do not squeeze the release handle, only push on top of the side jogger at the green label, to simulate the jogging action that the BM 61 does during run.

  1. Position the stapler heads over the correct anvils.
  2. Set the stapling switch to ON position.
  3. Set the folding switch to OFF position.
  4. Select manual start.
  5. Close the top cover.
  6. Set the power switch to ON position.
  7. To operate insert one set and press the manual start button. When stapled, remove set and insert the next one.

Page 18 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 19
Text on page 19
  1. Operation

Operating the bookletmaker

Operating ON-line

Verify that the set up of the Booklet Maker is completed.

Select “third party output” on the Collator.

Press “calibration” on the Collator.

The set will enter the Booklet Maker and remain in the stapling section unstapled.

Verify that the set is completed/correct press the Collator start button.

Select speed with button as shown below. (Only possible with model 510)

Operating OFF-line

Select manual or automatic start. Manual start: Make sure that the time delay is set to minimum. Press the manual start button for each operation.

Automatic start:The set will automatically be stapled as it is inserted in the BookletMaker.

When operating, insert one set at a time. Align the set with your fingertip. When automatic mode is selected, set time delay to allow careful alignment.

Note The manual start button will light up when the next set may be inserted.

Page 19 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 20

Page 20 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 21
Text on page 21
  1. Troubleshooting

Troubleshooting

PROBLEM

POSSIBLE CAUSES

ACTION

Paper jam in fold roller section

Folding not selected Side joggers set too tight

Select folding on control panel Adjust side joggers correctly

Stapler jam Bad sheet alignment side Bad sheet alignment front to back

Not possible to select third party eject on Collator

Paper jam into side guides

Paper jam in infeed area

Set remaining in stapling section

Too much material on belt stacker Switch on power, when the green button is lit, push it immediately for reversal feed motion on rolls. Stapler not aligned with anvils Align staplers with anvil Side joggers incorrectly adjusted Adjust side joggers to the paper size Adjust rear jogger Rear jogger incorrectly adjusted Upper pressure roller missing Mount upper pressure roller Upper pressure roller incorrectly Position the upper pressure roller to positioned correct paper size Attach connection cable Connection cable not attached Close top cover Top cover open Power switch set to OFF position Set power switch to ON position Clear jam in Booklet Maker Booklet Maker in jam condition Booklet Maker incorrectly Reposition the Booklet Maker for positioned to Collator the correct paper size Paper size setting incorrect Adjust side joggers to the correct paper size Upper guides on side jogger Fold down upper guides unfolded Upper pressure roller incorrectly Reposition the pressure roller positioned Rear jogger unit lowered in ON- Raise the rear jogger line mode Lower stapler Load stapler Misfeed in Collator Correct problem in Collator and restart Paper jam in Booklet Maker Clear paper jam Side jogger set too tight Adjust the side joggers to the correct paper size

Page 21 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 22

Page 22 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 23
Text on page 23
  1. General remarks

Do’s And Don’ts

Always connect the equipment to a properly grounded power source receptacle. When in doubt, have the receptacle checked by a qualified electrician

Warning Improper connection of the equipment grounding conductor can result in electrical shock.

Always follow all warnings marked on, or supplied with, the equipment.

Always locate the equipment on a solid support surface with adequade strenghth for the weight of the machine.

Always exercise care in moving or relocating the equipment

Always keep magnets and all devices with strong magnetic field away from the machine.

Do not use a ground adapter plug to connect the equipment to a power source receptacle that lacks a ground connection terminal.

Do not attempt any maintenance function that is not specifically described in this documentation.

Do not remove the covers or guards that are fastened with screws.

Do not install the unit near a radiator or any other heat source.

Do not override or “cheat” electrical or mechanical interlock devices.

Do not operate the equipment if you notice unusual noises or odours. Disconnect the power cord from the power source receptacle and call your customer service engineer to correct the problem.

Page 23 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 24
Text on page 24

Placing Your Machine

Machine Environment

Always locate the equipment on a solid support surface with adequate strength for the weight of the machine.

Always keep magnets and all devices with strong magnetic fields away from the machine.

  1. General Remarks

If the place of installation is air-conditioned or heated, do not place the machine where it will be:

Subjected to sudden temperature changes.

Directly exposed to cool air from an air-conditioner.

Directly exposed to heat from a heater.

Power Connection

Warning Improper grounding of the equipment can result in electrical shock.

Always connect the equipment to a properly grounded power source. If in doubt, have the power source checked by a qualified electrician.

Never connect the machine to a power source that lacks a ground connection terminal.

Page 24 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 25
Text on page 25
  1. Specifications

Technical specification

10 sheets 80 gsm (incl. cover) 22 sheets 80 gsm 10 sheets 20 lb bond (incl. cover) 22 sheets 20 lb bond

Speed - Model 510

High 1800 A4 sized booklets/hour

Adjustable up to 1800 A5 or 1400 A4 sized booklets/hour

1600 A3 sized booklets/hour

Low 1600 A4 sized booklets/hour

1200 A3 sized booklets/ hour

Speed - Model 310/306

Min Max

1600 A4 sized booklets/hour 1400 A4 sized booklets/hour

Adjustable up to 1800 A5 or 1400 A4 sized booklets/hour

200 x 270 mm, 7 7 / 8 ” x 10 5 / 8 ” 305 x 440 mm, 12” x 17 1 / 4 ”

Jam detection Jogging

Side and back 550 mm (880 mm incl. base) 21 5 / 8 ” (34 5 / 8 ” incl. base) 780 mm (1420 mm incl. Belt Stacker) 30 11 / 16 “ (55 7 / 8 “ incl Belt Stacker) 500 mm 19 5 / 16 “ 58 kg 128 lb 115 V 60 Hz 230/240 V 50 Hz

Page 25 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 26

Page 26 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 27

Page 27 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 28

Page 28 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 29

Page 29 of 30

Morgana BM61 Booklet Maker with Side Jogging Unit Instruction Manual, page 30

Page 30 of 30 ยท End of manual

Quick start

  1. Plug in the power cord and set the power switch to 1; the green lamp lights when the power is on.
  2. Open the top cover and set both side joggers to the paper size on the scale.
  3. Insert a set and push the rear side jogger against it (at the green label, without squeezing the release handle) to check the sheets align.
  4. Turn the paper stop crank until the trail edge of the set lines up with the paper length scale, then move the rear jogger up against the trail edge.
  5. Position the upper pressure roller according to the scale and set the stapler heads over the anvils to be used.
  6. For on-line use, attach the BM 61 to the collator so the green mark on the Docking Bracket aligns with the green mark on the collator.
  7. Switch stapling and folding ON, close the top cover and turn on the power.
  8. On the collator, select "third party output", press "calibration", check the set in the stapling section, then press the collator start button.

Troubleshooting

ProblemLikely causeFix (from the manual)
Paper jam in the fold roller sectionFolding not selected, or side joggers set too tight.Select folding on the control panel and adjust the side joggers correctly. Page 21
Stapler jamBad sheet alignment, or the stapler is not aligned with the anvils.Align the staplers with the anvils and adjust the side joggers and rear jogger to the paper size. Page 21
Cannot select third party eject on the collatorConnection cable not attached, top cover open, power switched off, or the booklet maker is in a jam condition.Attach the connection cable, close the top cover, set the power switch to ON and clear any jam in the booklet maker. Page 21
Paper jams into the side guidesBooklet maker positioned incorrectly to the collator, wrong paper size setting, or side jogger upper guides unfolded.Reposition the booklet maker for the correct paper size, adjust the side joggers and fold down the upper guides. Page 21
Stapler out of staplesLow stapler.Load the stapler. Page 21

Frequently asked questions

Can the BM 61 be used without a collator?

Yes. It can run as a stand-alone unit (off-line) or be installed against collator model 310/306 or collator/feeder model 510 (page 7).

How fast is the BM 61?

Off-line it is adjustable up to 1,800 A5 or 1,400 A4 booklets per hour. With the model 510 on high speed it runs 1,800 A4 or 1,600 A3 booklets per hour (page 25).

What paper sizes does the BM 61 handle?

From 200 x 270 mm (7 7/8" x 10 5/8") up to 305 x 440 mm (12" x 17 1/4") (page 25).

How do I set up the BM 61 for a non-standard paper size on-line?

Set up the booklet maker for the paper, attach it using the positioning holes that best match, loosen the odd-size knob on the Docking Bracket and slide the machine sideways until the green mark on the rear side jogger aligns with the green mark on the collator (page 14).

How do I prepare the BM 61 for off-line use?

Remove the upper pressure roller assembly, flip over both side jogger upper guides and lower the rear jogger unit by pressing it forward and down at the green mark (page 16).