Morgana DocuCrease 35 Manual 14" Hand, page 1

Page 1 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 2
Text on page 2

Docu-Crease 35 and 52

Docu-Crease 35 and 52

Operators & Parts Manual

© Morgana 2001 40 -001 issue 6

From Serial No. - 472592

Page 2 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 3
Text on page 3

Docu-Crease 35 and 52 Operating Instructions

Place the Docu-Crease on a stable bench or table.

1 Using the measurement scales, set the stops to the

Note the weight of the A3 Docu-Crease 35 = 13kgs

required position as shown below. (i.e. for a crease length of 100mm, line the face of the stop up with the 100mm mark on the scale). Note the position for repeat jobs. Set the second stop for twin creasing applications.

and the A2 Docu-Crease 52 = 17kgs

The Docu-Crease has been ergonomically designed

to relieve operator fatigue as much as possible.

Please recycle the packaging.

Line this face of the Stop

up with the scale

Creases paper or board up to approximately 350gsm.

Suppresses damage to toner, ink and cardboard

Maximum creasing width is:

350mm with Docu-Crease 35

520mm with Docu-Crease 52

2 Insert the material to be creased through the slot on

the bed, under the first stop and align the material

against the lay strip.

  • Laminated stock, digital printing processes using

toner or ink, laser colour or black and white copies,

cardboard, coated stock, varnished surfaces,

  • Folding paper or cardboard against the grain.
  • Greeting cards, reply cards, invitations, menus,

laminates or covers prior to adhesive binding or

  • The creasing tool width suits most available stocks

and materials with out the necessity for adjustments.

3 Keeping the material tight against the lay strip, slide the material towards the creasing head until it is clear of the stop. Then slide the material back towards the stop as far as it will go.

4 Move the handle downwards until you feel a slight resistance when the top creasing blade is touching the material. Apply light downward pressure to the

handle and an accurate crease will be formed. Lift

the handle to the upright position. Remove the

material if only one crease is required.

Note: Applying heavy pressure will not create a

better or deeper crease and may even damage

5 When a second crease is required, move the material

along to the second stop. Re-align again to the stop and lay strip as described in step 3.

6 Repeat the creasing process as described in step 4.

7 Hand fold along the crease.

Note: always fold on the reverse of the creased side.

Page 3 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 4

Page 4 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 5
Text on page 5

Docu-Crease 35 parts list

PLATE

Bed - 350 x 600

Screw - Socket button head M8 x 25

Fixing Feet - Black

Screw - Pan Pozi Taptite M4 x 8

Lay Strip - Input

Lay Strip - 350

Screw - Cap head M4 x 8

Washer - Plain M4

Universal Knob Assy. - M5 x 13 Lg - Black

Quantity per machine

Page 5 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 6
Text on page 6

PLATE

Morgana Docu-Crease 35 A

Creaser mechanism plate B

Page 6 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 7
Text on page 7

Docu-Crease 35 parts list

PLATE

Spirol Pin 5 x 26 carbon steel

Creasing Blade - 350

Thrust Pad - blade

Cam Shaft - 350

Screw - Socket Set - Flat point M4 x 16

Facia Plate - Side Cheek

Screw - Socket Set - Knurled point M4 x 6

Front Cover - 350 wide

Rear Cover - 350 wide

Screw - Pan Pozi Taptite M4 x 6

Quantity per machine

Page 7 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 8

Page 8 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 9
Text on page 9

Docu-Crease 52 parts list

PLATE

Bed - 520 x 700

Screw - Socket button head M8 x 25

Fixing Feet - Black

Screw - Pan Pozi Taptite M4 x 8

Lay Strip - Input

Lay Strip - 520

Screw - Cap head M4 x 8

Washer - Plain M4

Universal Knob Assy. - M5 x 13 Lg - Black

Quantity per machine

Page 9 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 10
Text on page 10

PLATE

Morgana Docu-Crease 52 C

Creaser mechanism plate D

Page 10 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 11
Text on page 11

Docu-Crease 52 parts list

PLATE

Spirol Pin 5 x 26 carbon steel

Creasing Blade - 520 wide

Thrust Pad - blade

Cam Shaft - 520

Screw - Socket Set - Flat point M4 x 16

Facia Plate - Side Cheek

Screw - Socket Set - Knurled point M4 x 6

Front Cover - 520 wide

Rear Cover - 520 wide

Screw - Pan Pozi Taptite M4 x 6

Quantity per machine

Page 11 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 12

Page 12 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 13
Text on page 13

Docu-Crease 35 and 52

MAINTENANCE

Blade Pressure Adjustment

  1. Remove the solid cover by unscrewing the six pan head pozi screws.
  2. Remove the top screws of the slotted handle cover as shown in FIG.1.
  3. Loosen the four top locking grub screws as shown in FIG. 2.
  4. Depress the handle to the stop position as shown in FIG. 3, insert a 2.5mm allen key into the bronze bearing adjustment hole and rotate downwards until it stops. Repeat both sides and then tighten the four locking grub screws.
  5. Check crease and refit covers.

Page 13 of 14

Morgana DocuCrease 35 Manual 14" Hand, page 14
Text on page 14

ACCESSORIES AND OPTIONS

ITEM

PART NUMBER

DESCRIPTION

BLADE PRESSURE ADJUSTMENT KIT

DOCUCREASE 35 / 52

Page 14 of 14 ยท End of manual

Quick start

  1. Set up: Place the Docu-Crease on a stable bench or table.
  2. Set the stops: Use the measurement scales to set the stops. For a 100mm crease length, line the face of the stop up with the 100mm mark. Set the second stop for twin creasing.
  3. Insert material: Slide the material through the slot on the bed, under the first stop. Align it against the lay strip.
  4. Position it: Keep the material tight against the lay strip. Slide it toward the creasing head until it is clear of the stop, then back toward the stop as far as it goes.
  5. Crease: Move the handle down until you feel slight resistance. Apply light downward pressure, then lift the handle upright.
  6. Second crease: Move the material to the second stop, align it again to the stop and lay strip, and repeat the creasing.
  7. Fold: Fold by hand along the crease. Always fold on the reverse of the creased side.

Troubleshooting

ProblemLikely causeFix (from the manual)
Crease is not deeper or better with more forceHeavy pressure does not make a better or deeper crease.Apply only light downward pressure on the handle. Heavy pressure may cause damage. Page 3
Crease is in the wrong placeThe stops are not set to the right mark, or the material is not aligned.Line the face of the stop up with the scale mark. Keep the material tight against the lay strip and slide it back to the stop. Page 3
Material is too thickThe machine creases paper or board only up to about 350gsm.Use material within about 350gsm. Page 3
Material is too wideThe maximum creasing width is 350mm for the Docu-Crease 35 and 520mm for the Docu-Crease 52.Use material within the maximum creasing width. Page 3
Crease quality is poor and blade pressure needs adjustingThe blade pressure needs to be adjusted.Remove the solid cover and the top screws of the slotted handle cover. Loosen the four top locking grub screws. Depress the handle to the stop and turn a 2.5mm allen key in the bronze bearing adjustment hole downwards until it stops. Repeat on both sides, tighten the grub screws, check the crease and refit the covers. Page 13

Frequently asked questions

What thickness can the Docu-Crease crease?

Paper or board up to approximately 350gsm. See page 3.

What is the maximum creasing width?

350mm for the Docu-Crease 35 and 520mm for the Docu-Crease 52. See page 3.

How do I fold after creasing?

Fold by hand along the crease. Always fold on the reverse of the creased side. See page 3.

Does pressing harder make a better crease?

No. Heavy pressure will not create a better or deeper crease and may cause damage. Use light pressure. See page 3.

How do I adjust the blade pressure?

Remove the covers, loosen the four top locking grub screws, and turn a 2.5mm allen key in the bronze bearing adjustment hole downwards until it stops on both sides. Then tighten the screws. See page 13.