Morgana ElectroCreaser-36 User Manual, page 1

Page 1 of 15

Morgana ElectroCreaser-36 User Manual, page 2

Page 2 of 15

Morgana ElectroCreaser-36 User Manual, page 3
Text on page 3

INDEX

SAFETY Do’s & Don’ts

LABELED DRAWING

OPERATING INSTRUCTIONS

ILLUSTRATED PARTS LIST

Pages 7 to 11

WIRING DIAGRAM

ROUTINE MAINTENANCE

RECOMMENDED SPARES LIST

Specification

Length Width Height Weight

700mm 480mm 218mm 25Kgs

Maximum Crease:- (To Backstop)

Length Width

435mm 365mm

Minimum Crease:- (To Backstop)

Power Requirement:- 1 phase 200 / 253v 50 / 60Hz

1 phase 100 / 125v 60Hz

PAPER

Page 3 of 15

Morgana ElectroCreaser-36 User Manual, page 4
Text on page 4

ElectroCreaser 36

Safety Do’s & Don’ts

Safety Do’s & Don’ts

Do - read this operator manual fully before operating the machine. Do - operate with the designated AC current only. Use an exclusive outlet, as overloading may cause fire or an electric shock. Do - install the power cord out of the way to avoid a tripping hazard. Do - beware of finger traps when replacing roller cassette and fold plates.

Do not - install the machine in an unstable place such that it tilts or shakes. Do not - unplug the plug or unplug the power cord from the outlet with a wet hand, this can cause an electric shock. Do not - unscrew and remove any covers from the machine, as it can cause an electric shock or injury. Do not - place receptacles containing liquids on any surface. Do not - adjust any part of the machine whilst rollers are running Do not - operate the machine with loose or trailing clothing or loose hair.

CREASER

Page 4 of 15

Morgana ElectroCreaser-36 User Manual, page 5

Page 5 of 15

Morgana ElectroCreaser-36 User Manual, page 6
Text on page 6

ElectroCreaser 36

BLANK

PAGE

CREASER

Page 6 of 15

Morgana ElectroCreaser-36 User Manual, page 7
Text on page 7

OPERATING INSTRUCTIONS

REFER TO LABELED DRAWING ON PAGE 3.

  1. Check that the voltage selector switch (4) is set to the required input voltage,120V or 240V.

IMPORTANT.

For 120V operation the fuse in the mains switch (5) must be a 4A antisurge fuse, for 240V operation the fuse must be a 2A anti-surge fuse.

  1. Switch on the power, mains switch (5).
  2. Set the crease length as follows:-

(i) Line the face of the Speed Stop (2) up with the scale on the copy table

  1. as shown below. (i.e. for a crease length of 100mm, line the face of the Speed Stop up with the 100mm mark on the copy table).

Line this face of the Speed Stop up with the scale

  1. Slide the sheet under the speed stops and against the side lays in the direction of the creasing head. As the end speed stop drops down behind the sheet edge, slide the sheet back to contact the stop. Press the foot switch to crease the sheet. Repeat this operation for as many stops that are in use. Slide the sheet out of the machine.
  2. The machine is set on the narrow crease at the factory. To change to the wider crease proceed as follows:-

(i) Undo the inner adjustment knob (7).

(ii) Turn the outer adjustment knob (7) until the spring loaded ball locates the wider crease position.

(iii) Lightly tighten the inner adjustment knob, place a sheet under the head and operate the machine. This will centre the tools.

(iv) Tighten the inner adjustment knob securely.

PAPER

Page 7 of 15

Morgana ElectroCreaser-36 User Manual, page 8
Text on page 8

ElectroCreaser 36

ITEM NO.

CREASER

ILLUSTRATED PARTS LIST

QTY.

CREASER MECHANISM - Electrocreaser 36. Speed Stop Assy. LAY STRIP - Short - ElectroCreaser. LAY STRIP - Long - ElectroCreaser. END COVER PLATE. FOLDED COVER PLATE. SIDE COVER - Plastic. MOTOR CAM - ElectroCreaser Control Board Assy. Label - Crease Width Label - Single Sheet Operation Base Cover - Electrocreaser 36 Base - Hinged LEG -ElectroCreaser. Base - Electrocreaser MK2 Fuse Rating Label Crank Block - Motor Crank Block - Cam - Ø10l Toroidal Transformer Assembly Jack Socket Lead Assembly FOOT - M4 - Black NYLON PILLAR - M4 Male/Male Gas Strut KNURLED KNOB - Female. KNURLED KNOB - Male. Doga - Motor & Gearbox FUSED POWER INLET. Microswitch Foot Switch Switch - Voltage Selector - 120/240V PCB Mounting Pillar Warning Label - Isolate Bridge Rectifier Fuse - 2A - 20 x 5mm - Anti-surge Fuse - 4A - 20 x 5mm - Anti-surge Screw - Pan Pozi Taptite - M2.5 x 12 Lg. Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Socket Cap Head - M4 x 6 Lg. Screw - Socket Cap Head - M4 x 8 Lg. Screw - Socket Cap Head - M4 x 10 Lg. Screw - Socket Cap Head - M4 x 16 Lg. Screw - Socket Set - Flat Point - M6 x 30 Lg. Screw - Hexagon Head - M6 x 12 Lg. Nut - Full - M2.5 Nut - Full - M4 Nut - Full - M6 Domed Nut - M4 Washer - Plain - M2.5 Washer - Plain - M4 Washer - Plain - M6 Compression Spring

Page 8 of 15

Morgana ElectroCreaser-36 User Manual, page 9
Text on page 9

ILLUSTRATED PARTS LIST

PAPER

Page 9 of 15

Morgana ElectroCreaser-36 User Manual, page 10
Text on page 10

ElectroCreaser 36

CREASER

ILLUSTRATED PARTS LIST

Page 10 of 15

Morgana ElectroCreaser-36 User Manual, page 11
Text on page 11

ILLUSTRATED PARTS LIST

PAPER

Page 11 of 15

Morgana ElectroCreaser-36 User Manual, page 12
Text on page 12

ElectroCreaser 36

CREASER

ILLUSTRATED PARTS LIST

Page 12 of 15

Morgana ElectroCreaser-36 User Manual, page 13
Text on page 13

WIRING DIAGRAM

PAPER

Page 13 of 15

Morgana ElectroCreaser-36 User Manual, page 14
Text on page 14

ElectroCreaser 36

ROUTINE MAINTENANCE

It is recommended that the following lubrication is carried out at monthly intervals

  1. Remove the creasing head top cover.
  2. Trickle oil into the slots, at both ends of the shaft, as shown in FIG.1 & FIG.2.
  3. Liberally coat the top of the nuts and the areas of the shaft that contact the head of the nuts with PTFE grease, as shown in FIG.3.

CREASER

Page 14 of 15

Morgana ElectroCreaser-36 User Manual, page 15
Text on page 15

RECOMMENDED SPARES LIST

ITEM NO.

QTY.

CREASER MECHANISM - Electrocreaser 36.

Control Board PCB Assembly Toroidal Transformer Assembly

Jack Socket Lead Assembly FOOT - M4 - Black

GAS STRUT

KNURLED KNOB - Female.

KNURLED KNOB - Male. Doga Motor & Gearbox

FUSED POWER INLET.

Microswitch Foot Switch Bridge Rectifier Fuse - 2A - 20 x 5mm - Anti-surge Ceramic (For 240V Operation)

Fuse - 4A - 20 x 5mm - Anti-surge Ceramic (For 110V Operation)

NOTE....

The items listed above represents parts which are subject to wear, loss, or accidental damage, and is included for your guidance only. Item numbers refer to the illustrations and tables in this manual. Replacement of parts fitted to your machine require specialist knowledge and should therefore be entrusted to your dealer.

PAPER

Page 15 of 15 ยท End of manual

Quick start

  1. Check voltage: Make sure the voltage selector switch is set to 120V or 240V. Use a 4A anti-surge fuse for 120V or a 2A anti-surge fuse for 240V.
  2. Power on: Switch on the mains switch.
  3. Set crease length: Line the face of the Speed Stop up with the scale on the copy table. For a 100 mm crease, line it up with the 100 mm mark.
  4. Load the sheet: Slide the sheet under the speed stops and against the side lays, toward the creasing head. When the end speed stop drops behind the sheet edge, slide the sheet back to touch the stop.
  5. Crease: Press the foot switch. Repeat for each stop in use, then slide the sheet out.
  6. Change crease width if needed: The machine is set to the narrow crease at the factory. Undo the inner knob, turn the outer knob until the ball locates the wider position, lightly tighten the inner knob, run a sheet to center the tools, then tighten the inner knob.
  7. Lubricate monthly: Remove the head top cover, trickle oil into the shaft slots at both ends, and coat the nuts and shaft contact areas with PTFE grease.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not run correctly on your power supplyVoltage selector or fuse does not match the supplySet the voltage selector to 120V or 240V. Use a 4A anti-surge fuse for 120V and a 2A anti-surge fuse for 240V. Page 7
Crease is the wrong lengthSpeed Stop is not lined up with the scaleLine the face of the Speed Stop up with the scale on the copy table at the length you need. Page 7
Crease is off center after switching to the wider creaseTools are not centeredLightly tighten the inner knob, run a sheet under the head to center the tools, then tighten the inner knob securely. Page 7
Machine tilts or shakesIt is installed on an unstable surfacePlace the machine on a stable surface. Do not install it where it tilts or shakes. Page 4
Creasing head needs routine careMonthly lubrication is recommendedRemove the head top cover, oil the shaft slots and apply PTFE grease to the nuts and shaft contact areas. Page 14

Frequently asked questions

What power does the ElectroCreaser 36 need?

It runs on single phase 200 to 253V at 50 or 60 Hz, or single phase 100 to 125V at 60 Hz. See page 3.

Which fuse should I use?

Use a 4A anti-surge fuse for 120V operation and a 2A anti-surge fuse for 240V operation. See page 7.

How do I change to the wider crease?

Undo the inner adjustment knob and turn the outer knob until the spring loaded ball locates the wider position. Lightly tighten the inner knob, run a sheet to center the tools, then tighten it fully. See page 7.

How often does it need lubrication?

Lubrication is recommended once a month. See page 14.

Can I adjust the machine while it is running?

No. Do not adjust any part of the machine while the rollers are running. See page 4.