Morgana ElectroCreaser-52 User Manual, page 1

Page 1 of 15

Morgana ElectroCreaser-52 User Manual, page 2

Page 2 of 15

Morgana ElectroCreaser-52 User Manual, page 3
Text on page 3

INDEX

SAFETY Do’s & Don’ts

LABELED DRAWING

OPERATING INSTRUCTIONS

ILLUSTRATED PARTS LIST

Pages 7 to 11

WIRING DIAGRAM

ROUTINE MAINTENANCE

RECOMMENDED SPARES LIST

Specification

Length Width Height Weight

700mm 480mm 218mm 25Kgs

Maximum Crease:- (To Backstop)

Length Width

435mm 365mm

Minimum Crease:- (To Backstop)

Power Requirement:- 1 phase 200 / 253v 50 / 60Hz

1 phase 100 / 125v 60Hz

PAPER

Page 3 of 15

Morgana ElectroCreaser-52 User Manual, page 4
Text on page 4

ElectroCreaser 36

Safety Do’s & Don’ts

Safety Do’s & Don’ts

Do - read this operator manual fully before operating the machine. Do - operate with the designated AC current only. Use an exclusive outlet, as overloading may cause fire or an electric shock. Do - install the power cord out of the way to avoid a tripping hazard. Do - beware of finger traps when replacing roller cassette and fold plates.

Do not - install the machine in an unstable place such that it tilts or shakes. Do not - unplug the plug or unplug the power cord from the outlet with a wet hand, this can cause an electric shock. Do not - unscrew and remove any covers from the machine, as it can cause an electric shock or injury. Do not - place receptacles containing liquids on any surface. Do not - adjust any part of the machine whilst rollers are running Do not - operate the machine with loose or trailing clothing or loose hair.

CREASER

Page 4 of 15

Morgana ElectroCreaser-52 User Manual, page 5

Page 5 of 15

Morgana ElectroCreaser-52 User Manual, page 6
Text on page 6

ElectroCreaser 36

BLANK

PAGE

CREASER

Page 6 of 15

Morgana ElectroCreaser-52 User Manual, page 7
Text on page 7

OPERATING INSTRUCTIONS

REFER TO LABELED DRAWING ON PAGE 3.

  1. Check that the voltage selector switch (4) is set to the required input voltage,120V or 240V.

IMPORTANT.

For 120V operation the fuse in the mains switch (5) must be a 4A antisurge fuse, for 240V operation the fuse must be a 2A anti-surge fuse.

  1. Switch on the power, mains switch (5).
  2. Set the crease length as follows:-

(i) Line the face of the Speed Stop (2) up with the scale on the copy table

  1. as shown below. (i.e. for a crease length of 100mm, line the face of the Speed Stop up with the 100mm mark on the copy table).

Line this face of the Speed Stop up with the scale

  1. Slide the sheet under the speed stops and against the side lays in the direction of the creasing head. As the end speed stop drops down behind the sheet edge, slide the sheet back to contact the stop. Press the foot switch to crease the sheet. Repeat this operation for as many stops that are in use. Slide the sheet out of the machine.
  2. The machine is set on the narrow crease at the factory. To change to the wider crease proceed as follows:-

(i) Undo the inner adjustment knob (7).

(ii) Turn the outer adjustment knob (7) until the spring loaded ball locates the wider crease position.

(iii) Lightly tighten the inner adjustment knob, place a sheet under the head and operate the machine. This will centre the tools.

(iv) Tighten the inner adjustment knob securely.

PAPER

Page 7 of 15

Morgana ElectroCreaser-52 User Manual, page 8
Text on page 8

ElectroCreaser 36

ITEM NO.

CREASER

ILLUSTRATED PARTS LIST

QTY.

CREASER MECHANISM - Electrocreaser 36. Speed Stop Assy. LAY STRIP - Short - ElectroCreaser. LAY STRIP - Long - ElectroCreaser. END COVER PLATE. FOLDED COVER PLATE. SIDE COVER - Plastic. MOTOR CAM - ElectroCreaser Control Board Assy. Label - Crease Width Label - Single Sheet Operation Base Cover - Electrocreaser 36 Base - Hinged LEG -ElectroCreaser. Base - Electrocreaser MK2 Fuse Rating Label Crank Block - Motor Crank Block - Cam - Ø10l Toroidal Transformer Assembly Jack Socket Lead Assembly FOOT - M4 - Black NYLON PILLAR - M4 Male/Male Gas Strut KNURLED KNOB - Female. KNURLED KNOB - Male. Doga - Motor & Gearbox FUSED POWER INLET. Microswitch Foot Switch Switch - Voltage Selector - 120/240V PCB Mounting Pillar Warning Label - Isolate Bridge Rectifier Fuse - 2A - 20 x 5mm - Anti-surge Fuse - 4A - 20 x 5mm - Anti-surge Screw - Pan Pozi Taptite - M2.5 x 12 Lg. Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Socket Cap Head - M4 x 6 Lg. Screw - Socket Cap Head - M4 x 8 Lg. Screw - Socket Cap Head - M4 x 10 Lg. Screw - Socket Cap Head - M4 x 16 Lg. Screw - Socket Set - Flat Point - M6 x 30 Lg. Screw - Hexagon Head - M6 x 12 Lg. Nut - Full - M2.5 Nut - Full - M4 Nut - Full - M6 Domed Nut - M4 Washer - Plain - M2.5 Washer - Plain - M4 Washer - Plain - M6 Compression Spring

Page 8 of 15

Morgana ElectroCreaser-52 User Manual, page 9
Text on page 9

ILLUSTRATED PARTS LIST

PAPER

Page 9 of 15

Morgana ElectroCreaser-52 User Manual, page 10
Text on page 10

ElectroCreaser 36

CREASER

ILLUSTRATED PARTS LIST

Page 10 of 15

Morgana ElectroCreaser-52 User Manual, page 11
Text on page 11

ILLUSTRATED PARTS LIST

PAPER

Page 11 of 15

Morgana ElectroCreaser-52 User Manual, page 12
Text on page 12

ElectroCreaser 36

CREASER

ILLUSTRATED PARTS LIST

Page 12 of 15

Morgana ElectroCreaser-52 User Manual, page 13
Text on page 13

WIRING DIAGRAM

PAPER

Page 13 of 15

Morgana ElectroCreaser-52 User Manual, page 14
Text on page 14

ElectroCreaser 36

ROUTINE MAINTENANCE

It is recommended that the following lubrication is carried out at monthly intervals

  1. Remove the creasing head top cover.
  2. Trickle oil into the slots, at both ends of the shaft, as shown in FIG.1 & FIG.2.
  3. Liberally coat the top of the nuts and the areas of the shaft that contact the head of the nuts with PTFE grease, as shown in FIG.3.

CREASER

Page 14 of 15

Morgana ElectroCreaser-52 User Manual, page 15
Text on page 15

RECOMMENDED SPARES LIST

ITEM NO.

QTY.

CREASER MECHANISM - Electrocreaser 36.

Control Board PCB Assembly Toroidal Transformer Assembly

Jack Socket Lead Assembly FOOT - M4 - Black

GAS STRUT

KNURLED KNOB - Female.

KNURLED KNOB - Male. Doga Motor & Gearbox

FUSED POWER INLET.

Microswitch Foot Switch Bridge Rectifier Fuse - 2A - 20 x 5mm - Anti-surge Ceramic (For 240V Operation)

Fuse - 4A - 20 x 5mm - Anti-surge Ceramic (For 110V Operation)

NOTE....

The items listed above represents parts which are subject to wear, loss, or accidental damage, and is included for your guidance only. Item numbers refer to the illustrations and tables in this manual. Replacement of parts fitted to your machine require specialist knowledge and should therefore be entrusted to your dealer.

PAPER

Page 15 of 15 ยท End of manual

Quick start

  1. Read the rules: read the whole manual, use only the designated AC current on an exclusive outlet, and route the power cord out of the way.
  2. Match the supply: set the voltage selector switch (4) to 120V or 240V. The fuse in the mains switch (5) must be a 4A anti-surge for 120V or a 2A anti-surge for 240V, then switch the power on.
  3. Set the length: line the face of the Speed Stop (2) up with the scale on the copy table. For a 100mm crease, use the 100mm mark.
  4. Crease a sheet: slide the sheet under the speed stops and against the side lays toward the head. When the end speed stop drops behind the edge, slide the sheet back to touch it, press the foot switch, repeat for each stop in use and slide the sheet out.
  5. Go wider if needed: the machine ships on the narrow crease. Undo inner knob (7), turn the outer knob until the ball locates the wider position, lightly tighten the inner knob, run a sheet to center the tools, then tighten it securely.
  6. Service monthly: remove the head top cover, trickle oil into the slots at both ends of the shaft, and coat the nut tops and shaft contact areas with PTFE grease.

Troubleshooting

ProblemLikely causeFix (from the manual)
Outlet trips or there is a fire or shock riskThe outlet is overloadedUse an exclusive outlet and only the designated AC current. Page 4
Fingers pinched during a part changeThere are finger traps when replacing the roller cassette and fold platesTake care when replacing the roller cassette and fold plates. Page 4
Sheet does not line up with the stopThe sheet was not slid back after the end speed stop droppedWhen the end speed stop drops down behind the sheet edge, slide the sheet back to contact the stop, then press the foot switch. Page 7
Only one crease is made on the sheetThe operation was not repeated for each stop in useRepeat the slide-and-press operation for as many stops as are in use, then slide the sheet out. Page 7
Fuse needs replacingThe wrong fuse is fitted for the supplyUse fuse 2A, 20 x 5mm anti-surge ceramic for 240V or 4A, 20 x 5mm anti-surge ceramic for 110V. Ask your dealer to fit parts that need specialist knowledge. Page 15
Shock or injury risk when servicingA cover was unscrewed and removedDo not unscrew or remove any covers. Do not place liquids on any surface. Page 4

Frequently asked questions

How do I set a 100mm crease length?

Line the face of the Speed Stop up with the 100mm mark on the scale on the copy table. See page 7.

How do I lubricate the creasing head?

Every month, remove the creasing head top cover and trickle oil into the slots at both ends of the shaft. Then coat the top of the nuts and the contact areas of the shaft with PTFE grease. See page 14.

Can I remove the covers or unplug with wet hands?

No. Do not remove any covers, and do not unplug the machine or its power cord with a wet hand, as it can cause electric shock. See page 4.

Which parts are on the recommended spares list?

Items include the control board PCB assembly, toroidal transformer assembly, gas strut, motor and gearbox, foot switch, microswitch, bridge rectifier and the anti-surge fuses. See page 15.

What should I wear when operating it?

Do not operate with loose or trailing clothing or loose hair. See page 4.