

Page 1 of 38

Text on page 2
Major
PAPER FOLDING MACHINE
ILLUSTRATED PARTS MANUAL
ISSUE 11 May 2008
SERIAL No. 901641LEAF ONWARDS
Page 2 of 38

Text on page 3
INTRODUCTION
Major
ILLUSTRATED PARTS MANUAL
The Illustrated Parts Manual has been designed to assist when selecting a part or assembly which may be required to service or repair your machine.
The index on page four lists all of the major assemblies in the order in which the machine is constructed.
The following page demonstrates how to recognize a part from a sub-assembly and shows the quantity contained within the major assembly.
The major assembly number and description is listed at the top of the page and should always be quoted when ordering parts or when seeking technical advice.
Before ordering parts confirm that the model number of the machine (listed at the top of page four) is identical to the number stamped on the specification plate fixed as shown in section five (starting page 18). Whilst checking this, make a note of the serial number also stamped on the plate.
Some components will not be made available individually as they form part of a sub-assembly which may require specialist tools and knowledge to dismantle. The machine may not perform correctly if attempts are made to repair sub-assemblies of this type.
Accessories (section eleven) are available to help make the best possible use from the machine, such as the wider creasing blade set for use with heavier stocks.
Section twelve lists the recommended spares and the relevant sub-assemblies that they belong to in the event of worn or damaged parts.
NOTE....
ALWAYS READ THE OPERATORS MANUAL BEFORE MAKING ANY
ADJUSTMENTS TO YOUR MACHINE AND ALWAYS DISCONNECT THE POWER
SUPPLY BEFORE REMOVING ANY COVERS.
PAPER
Page 3 of 38

Page 4 of 38

Text on page 5
904222 (EEC) 954232 (USA)
CONTENTS
SECTION
ASSEMBLY
MAIN ASSEMBLY
DELIVERY ASSEMBLY
FEED BED ASSEMBLY
PAPER CONTROL ASSEMBLY
SERVICES - 50 Hz - (EEC) SERVICES - 60 Hz - (USA)
FOLD ROLLER ASSEMBLY
FOLD PLATE ASSEMBLY - Deflect
FOLD PLATE ASSEMBLY - Stop
STACKER ASSEMBLY
PERFORATOR ASSY. (Metric) PERFORATOR ASSY. (Imperial)
OPTIONAL REAR DELIVERY ASSY.
NOTE....
DESCRIPTION
PAGE
TIP.... To assist you in quickly finding the section you require, there are numbered tabs positioned down the outside edges of each page.
PAPER
Page 5 of 38

Text on page 6
Major
Major
PAPER FOLDING MACHINE
FOLDER
Page 6 of 38

Text on page 7
MAIN ASSEMBLY
27 42 2 off
59 45 2 off
60 46 2 off
26 44 4 off
55 60 47 2 off
33 56 61 2 off
33 56 61 2 off
44 - 4 off 42 - 3 off
PAPER
Page 7 of 38

Text on page 8
Major
MAIN ASSEMBLY
ITEM NO. PART No. 91-001-02 91-002-02 91-003 91-004 91-005-02 91-006 91-024 91-025 91-033 91-051 91-052 91-053-02 91-054 91-055-02 91-074-01 95-112 606-028 613-022 615-031 617-008 621-025 621-029 401-02-030-010 401-02-040-006 401-02-040-008 401-02-050-008 403-01-050-010 403-01-060-010 404-01-060-010 405-01-050-012 405-01-080-030 405-01-080-050 409-01-050-005 415-01-060-012 415-02-050-008 461-01-030 461-01-060 461-01-080 481-030 481-050 481-060 481-080
QTY.
Description MAIN FRAME - Major. PLINTH - Major. COMPRESSOR SUPPORT. COMPRESSOR STRAP. Axle - Wheels WHEEL TUBE - Junior. CORD PULLEY - Compressor. BUNG - Compressor. LOCATION PLATE - Lay Side. STOW HOOK - Op. Side. STOW HOOK - Drive Side. Shaft Stow Hook LOCATION PLATE - Op. Side. Bracket - Stowage Shaft INTERFACE PLATE - SV130 Compressor. Choke / Lead Assy. BLACK PLASTIC FOOT - M8 CABLE GLAND. FLEX LOC. BUSHES - M8 Wheel - Ø100 FAN - PLASTIC 5 BLADE 6" CCW BLOWER - SV130. Screw - Pan Pozi Taptite - M3 x 10 Lg. Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M5 x 8 Lg. Screw - Socket Cap Head - M5 x 10 Lg. Screw - Socket Cap Head - M6 x 10 Lg. Screw - Socket Countersunk - M6 x 10 Lg. Screw - Button Hd. - M5 x 12 Lg. Screw - Button Hd. - M8 x 30 Lg. Screw - Button Hd. - M8 x 50 Lg. Screw - Socket Set - Flat Point - M5 x 5 Lg. Screw - Hexagon Head - M6 x 12 Lg. Screw - Hexagon Head - Taptite - M5 x 8 Lg. Nut - Full - M3 Nut - Full - M6 Nut - Full - M8 Washer - Plain - M3 Washer - Plain - M5 Washer - Plain - M6 Washer - Plain - M8
THIS SECTION IS CONTINUED ON THE FOLLOWING PAGES
FOLDER
Page 8 of 38

Text on page 9
MAIN ASSEMBLY
59 48 2 off
44 30 2 off
44 - 2 off
43 58 4 off
43 31 4 off
PAPER
Page 9 of 38

Text on page 10
Major
MAIN ASSEMBLY
ITEM NO. PART No. 91-007-03 91-015 91-027-01 91-038 91-040 91-042 91-042-02 91-059 91-061-02 91-068-02 91-070 65-070 601-137 602-045 603-041 605-004 613-027 613-339 401-02-030-010 401-02-040-006 401-02-040-008 401-02-050-008 403-01-050-010 403-01-060-010 405-01-050-012 409-01-050-005 415-01-060-012 461-01-030 461-01-060 481-030 481-040 481-050 481-060
QTY.
FOLDER
Description CROSS STRAP - Major. SPACER - Reduction Shaft. BELT DRIVE PULLEY - DELIVERY BEARING HSG - Rear Drive. WORM WHEEL. KEY DRIVE ASSY. WORM - Extended Hub. Fan Cowl BRACKET - Motor Mtg. MOTOR ASSY. - DC Drive HANDWHEEL ASSEMBLY. SWITCH - Proximity. SHORTY PLUG. FLANGED SPYRALIGN BUSH SPIROL SPACER - Ø4 x Ø5.65 x 4 Lg. Thrust Washer - Ø8 x Ø15.88 x 0.79 TIE WRAP - Small. CABLE TIE MOUNTING Screw - Pan Pozi Taptite - M3 x 10 Lg. Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M5 x 8 Lg. Screw - Socket Cap Head - M5 x 10 Lg. Screw - Socket Cap Head - M6 x 10 Lg. Screw - Button Hd. - M5 x 12 Lg. Screw - Socket Set - Flat Point - M5 x 5 Lg. Screw - Hexagon Head - M6 x 12 Lg. Nut - Full - M3 Nut - Full - M6 Washer - Plain - M3 Washer - Plain - M4 Washer - Plain - M5 Washer - Plain - M6
Page 10 of 38

Page 11 of 38

Text on page 12
DELIVERY ASSEMBLY
QTY.
DESCRIPTION
UNIVERSALKNOB-M4-Ø12.7-Black Screw - Pan Pozi Taptite - M4 x 6Lg. Screw - Pan Pozi Taptite - M4 x 8Lg. Screw - Pan Pozi Taptite - M4 x 10Lg. Screw - Pan Pozi Taptite - M5 x 8Lg. Screw - Socket Cap Head - M6 x 10Lg. Screw - ButtonHd. - M4 x 8Lg. Screw - ButtonHd. - M6 x 10Lg. Screw - Socket Set - Flat Point - M4 x 4Lg. Screw - Socket Set - Flat Point - M4 x 16Lg. Nut - Full - M6 Washer - Plain - M4 Washer - Plain - M6 Washer - Plain - M8 Idler Pulley
DISC SPRING
THRUST WASHER - Ø6.6 x Ø11.1 x 1.19 THRUST WASHER - Ø5.1 x Ø9.5 x 0.75 Twin Gip Timing Belt - 140 XLD/12 Shoulder Bolt - Ø8 (M6) x 25Lg. Starlock Washer - M6 Capped Circlip - External - No Groove M1440-0100 Delivery Frame Delivery Cover STACKER - Hinged. SUPPORT STRAP. Shaft - Delivery Idler Support Shaft - Delivery Transport Belt - Delivery Control Collar - Stacker Catching Frame - Delivery Roller - Delivery End Cap - Stacking Roller Axle - Stacker Roller Flat Drive Belt - Delivery Cord Guard Cord Roller Assy. Delivery Idler Assy Slide Frame Assy Grab Handle - Auto Support Bracket - Leadscrew Slide Shaft - Long Spacer - Delivery Roller Frame support - Delivery
FOLDER
Major
Page 12 of 38

Text on page 13
secured by 38 49 (2 off)
secured by 38 49 (2 off)
FEED BED ASSEMBLY
PAPER
Page 13 of 38

Text on page 14
ITEM NO.
QTY.
FEED BED ASSEMBLY
PART NO. 93-001-02 93-002-02 93-004 93-005 93-007 93-010 93-020 93-023 93-024-02 93-025 93-027-02 93-028 93-029 93-033 93-037-02 51-095 601-088 605-004 607-027 609-014 73-004 01-119 401-02-040-008 401-02-040-016 402-02-040-008 403-01-040-008 403-01-060-012 405-01-060-012 408-01-050-030 409-01-040-006 409-01-040-012 409-01-060-035 414-01-080-012 417-04-006-312 461-01-060 481-040 481-060 481-080 73-05-02 73-066-01 94-021
DESCRIPTION
Frame - Feed System - Wide Manifold Plate Air Distribution Tube Knob - Air Distribution Belt Support Support Plate Feed Drive Pulley 16XL - Flanged Shield - Self Aligning Ball Race Anti-Static Brush Strip Lower Sensor Assy Baffle - Feed System Smoother - Delivery Manifold Tube Assy Support Bracket - Control Bed Extension - Loading Table Clamp Washer Spring Plunger - Press In Thrust Washer - Ø8 x Ø15.88 x 0.79 Toothed Belt - 110XL 'O' Ring Ø15 x Ø3 Key Hole Latch Small Knob Universal M6 Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 16 Lg. Screw - Csk Hd. Taptite - M4 x 8 Lg. Screw - Socket Cap Head - M4 x 8 Lg. Screw - Socket Cap Head - M6 x 12 Lg. Screw - Button Hd. - M6 x 12 Lg. Screw Skt Cone Pt - M5 x 30 Lg. Screw - Socket Set - Flat Point - M4 x 6 Lg. Screw - Socket Set - Flat Point - M4 x 12 Lg. Screw - Socket Set - Flat Point - M6 x 10 Lg. Bolt - Hexagon Head - M6 x 12 Lg. Screw - Trunc. Csk Hd. Taptite - #6-32 UNC x 0.312 Lg Nut - Full - M6 Washer - Plain - M4 Washer - Plain - M6 Washer - Plain - M8 Choke Bleed Assembly - Major Knob - Vacuum Bleed UP' LABEL - PAPER GATE
Major
THIS SECTION IS CONTINUED ON THE FOLLOWING PAGES
FOLDER
Page 14 of 38

Text on page 15
FEED BED ASSEMBLY
PAPER
Page 15 of 38

Text on page 16
FEED BED ASSEMBLY
ITEM NO. QTY. PART NO. 1 93-021 1 93-022 1 93-030-02 1 93-031 1 93-032 1 604-060 1 604-062 2 615-035 1 615-040
FOLDER
DESCRIPTION
Feed Belt Vacuum Roller Drive Belt Vacuum Roller Assy - Slotted Feed Drum Assy - Idler Feed Drum Assy - Drive Washer - Waved - Ø25.5 X Ø19 X 3 Washer - Waved - Ø35.5 X Ø43.5 x 0.4 Metric Push-in Fix Retaining Ring - External - Ø25
Major
Page 16 of 38

Page 17 of 38

Text on page 18
Major
PAPER CONTROL
ITEM No. QTY PART NO. 1 94-003 1 94-006 1 94-020 1 94-021 1 94-038 1 94-068 2 94-026 2 94-028 1 94-039 1 94-040 1 94-051-02 1 94-052-02 1 74-06-01 1 74-06-02 1 74-06-03 1 74-06-04 1 74-06-05 1 94-058 1 94-059 1 94-075 1 603-050 1 604-037 1 604-061 1 605-041 2 605-043 5 617-003 2 401-02-050-020 2 403-01-040-008 1 409-01-040-006 21 417-04-006-312 1 461-01-100 1 481-100
DESCRIPTION
CONTROL BED. UPPER - SENSOR ASSY KNOB - Papergate. LABEL - Papergate 'UP'. LABEL - Papergate 'AUF' (Nagel). LABEL - Papergate 'UP' (French). CLAMP KNOB - Sidelay. LOCK PIN ASSY. - Side Lay. CHASSIS - Papergate. PAPERGATE - Rectangular. Loading Table Feed Bed Moving Sidelay - Metric - Major. Moving Sidelay - Imperial - Major. Moving Sidelay - French - Major. Moving Sidelay - Nagel - Major. Moving Sidelay - Japan - Major. BACKSTOP ASSY. SUPPORT POST. MEMBRANE - Moving Sidelay DOWEL - Ø6 x 28 Lg. DISC SPRING. SPRING - Compression. SHERICAL SEATING WASHER Nylon Washer - Ø5.1 xØ9.5 x 0.75 STEEL BALL - Ø20 Screw - Pan Pozi Taptite - M5 x 20 Lg. Screw - Socket Cap Head - M4 x 8 Lg. Screw - Socket Set - Flat Point - M4 x 6 Lg. Screw - Trunc. Csk Hd. Taptite - #6-32 UNC x 0.312 Lg Nut - Full - M10 Washer - Plain - M10
FOLDER
Page 18 of 38

Text on page 19
9-05-08 (EEC) 9-05-09 (USA)
2 Off
2 Off
4 Off
SERVICES - 50Hz (EEC) SERVICES - 60Hz (USA)
PAPER
Page 19 of 38

Text on page 20
ITEM NO. PART No. 95-001 95-009-02 95-011 95-017 95-018 95-019-02 95-020 95-030 95-042 95-071 95-072 95-031 95-032 95-038 95-039 95-040 95-063 95-069 95-106 95-130 95-131 95-132 95-108 601-036 609-011 609-013 613-065 613-067 613-136 613-137 613-237 613-238 613-255 613-365 613-377 613-385 613-386 401-02-040-008 402-02-040-008 403-01-050-035 461-01-040 481-040
SERVICES - 50Hz (EEC) SERVICES - 60Hz (USA)
QTY.
9-05-08 (EEC) 9-05-09 (USA)
Description
SERVICE PANEL
Compressor Panel SOLENOID VALVE SEAT. HOSE - Vacuum. HOSE - Air Seperation. Internal Baffle Display Lens LABEL - Air Seperation - UK LABEL - Air Seperation (Nagel) LABEL - Air Seperation (French) LABEL - Air Seperation (Japanese) HOSE - Evacuation. HOSE - Exhaust. LABEL - Manifold Numbrs. AIR CONTROL BLOCK ASSY. AIR SPOOL ASSY. CROSS TUBE - Valves. SOLENOID VALVE ASSY. BATCHER PANEL - Major (UK) BATCHER PANEL - Major (Nagel) BATCHER PANEL - Major (French) BATCHER PANEL - Major (Japanese) LABEL - Major. GROMMET 'O' Ring Ø20 x Ø3 'O' Ring. COLLET KNOB - Black Lined. NUT COVER - Black Lined. TUBE & NUT ASSY. SPRING & PLUNGER ASSY. - Mk2. KNOB CAP - Black. KNOB CAP - Black Lined. SOLENOID CONNECTOR EMERGENCY STOP SWITCH CEE 22 MAINS INLET - Snap-In COLLET KNOB - Black. NUT COVER - Black. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Csk Hd. Taptite - M4 x 8 Lg. Screw - Socket Cap Head - M5 x 35 Lg. Nut - Full - M4 Washer - Plain - M4
Major
THIS SECTION IS CONTINUED ON THE FOLLOWING PAGES
FOLDER
Page 20 of 38

Text on page 21
9-05-08 (EEC) 9-05-09 (USA)
SERVICES - 50Hz (EEC) SERVICES - 60Hz (USA)
PAPER
Page 21 of 38

Text on page 22
ITEM NO. PART No. 95-021 95-027 95-086 95-034 95-046 95-047 95-049 95-068 95-109 601-090 605-002 613-059
SERVICES - 50Hz (EEC) SERVICES - 60Hz (USA)
QTY.
9-05-08 (EEC) 9-05-09 (USA)
Description CONTROL PCB - Counter / Batcher Wiring Loom - EEC Wiring Loom - USA Voltage Selector Plug SWITCH ASSEMBLY - Reset / Pulse / Stream SWITCH ASSEMBLY - Feed ROTORY ENCODER ASSEMBLY LEAD - Diagnostic POT & LEAD ASSY - Motor Speed PILLAR - Hexagon NYLON WASHER FUSE HOLDER
PCB - Motor Speed Controller
REVERSE LOCKING SUPPORT
SWITCH - 10A - 12V Coil - EEC SWITCH - 16A - 12V Coil - USA CABLE TIE SWITCH SHROUD FUSE - 3.15A - 20 x Ø5mm - Fast Blow - Ceramic SCREW - Socket Cap Head - M3 x 6 Lg. SCREW - Socket Cap Head - M3 x 20 Lg. Nut - Full - M3 Washer - Plain - M3
FOLDER
Major
Page 22 of 38

Text on page 23
FOLD ROLLER ASSEMBLY
PAPER
Page 23 of 38

Text on page 24
FOLD ROLLER ASSEMBLY
ITEM NO. QTY. PART NO. 2 96-009-02 1 96-010 3 96-028-02 1 96-031 1 96-032-02 1 96-036-02 1 96-037 3 96-039-02 2 96-040 1 96-041-02 1 96-042-02 2 96-043 3 96-044 1 96-045 1 96-046 1 96-047 1 96-049-02 1 96-052 1 96-053 1 96-061 1 96-063 1 601-021 1 601-081 1 601-111 3 602-001 1 603-033 2 603-060 1 605-049 2 606-030 10 609-023 1 615-005 1 12-013 2 401-02-030-008 4 401-02-040-008 2 407-01-040-006 3 411-01-080-025 6 415-01-060-016 3 419-01-080-012 2 461-01-030 4 462-01-080 2 481-030 2 481-060 3 481-080 1 123-059
FOLDER
DESCRIPTION
Roller Support Shaft Large Tube Pulley - 36XL Fold Roller Assy - Standard - Wide Drive Belt - Wide Roller Guard - Wide Belt Drive Roller Assy - Crowned - Wide Side Plate (Gap) - Op Side Roller Shaft (Gap Set) Bush - Roller Tilt Idler Shaft Entry Guard - Handles Eccentric Bush - Roller Tilt Indicator - Roller Position Tilt Lever - Toothed Tilt Plate - Toothed Knob - Roller Tilt Lever Fold Roller Assy - Bottom - Wide Side Plate (Gap) - Lay Side Label - Roller Tilt Label - Roller Tilt (Nagel) Label - Roller Tilt (French) Magnetic Actuator Spring Plunger Tapered Ferrule BEARING-Deep Groove Ball - 6000-ZZ Tension Pin - Ø2 x 8 Long Spirol Coiled - Ø3 x 6 Lg. Nylon Washer - Ø15 x Ø21 x 1 Scallop Knob - Black 'O' Ring Ø15 x Ø2.5 CIRCLIP - External - No Groove Ø10 SPACER. Screw - Pan Pozi Taptite - M3 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Socket Set Knurled - M4 x 6 Lg. Screw - Socket Set - Dog Point - M8 x 25 Lg. Screw - Hexagon Head - M6 x 16 Lg. Screw - Skt. - Low Hd. Cap - M8 x 12 Nut - Full - M3 Half Nut - M8 Washer - Plain - M3 Washer - Plain - M6 Washer - Plain - M8 LABEL - Safety Warnings
Major
Page 24 of 38

Text on page 25
FOLD PLATE - Deflect
PAPER
Page 25 of 38

Text on page 26
ITEM NO.
FOLD PLATE - Deflect
QTY.
PART NO. DESCRIPTION 97-001-02 Top Box - Deflector - Wide 97-003-02 Bottom Box - Deflector - Wide 97-007-02 Bottom Rail - Deflector 97-009-03 Deflector (Extruded) 97-012 Deflector Guide 97-016 Belt Clamp 97-017 Guide Spacer 97-019-02 Top Rail Assy - Deflector - Wide 97-021 Control Dial Assembly 97-024-02 Shaft -Blade Control 97-025 Control Pulley 10XL Flanged 97-026 Control Lock 97-027 Control Lock Knob 97-028 Tilt Lock Knob 97-029-02 Idler Shaft 97-030 Idler Reel 97-031 Control Gear - Shaft 97-032 Control Gear - Pot 97-033 Potentiometer Bracket 97-034-02 Latching Shaft 97-038 Label - Pull Down to Lock 97-078 Label - Pull Down to Lock (Nagel) 97-098 Label - Pull Down to Lock (French) 97-039 Tilt Disc - Printed 97-077 Tilt Disc - Printed (Nagel) 97-139 Tilt Disc - Printed (French) 97-073-02 Deflector Carraige - Op Side 97-074-02 Deflector Carraige - Drive Side 97-075 Pot & Lead Assy. 97-087 Latching Bracket - Op Side 97-088 Latching Bracket - Lay Side 97-093-02 Spacer Plate - Top Rail (Defl.) 97-117 Bush - Bearing 98-013-02 Anti-Static Brush - Wide 601-084 Grommet - Ø12.7 X Ø15 X Ø20 X 1.6 604-070 Compression Spring 605-004 Thrust Washer - Ø8 x Ø15.88 x 0.79 605-021 Thrust Washer - Ø6.4 x Ø12 x 1.5 605-042 Nylon Washer - Ø4.3 x Ø8 x 1.0 606-019 Hinge - Adjustable Black Acetyl 607-026 Toothed Belt - 132XL 608-004 Shoulder Bolt - Ø6(M5) x 16 Lg. 615-009 Starlock Washer 615-016 CIRCLIP- External - Ø6 615-032 Flex Loc Bush - M4 401-02-040-006 Screw - Pan Pozi Taptite - M4 x 6 Lg. 401-02-040-008 Screw - Pan Pozi Taptite - M4 x 8 Lg. 401-02-040-016 Screw - Pan Pozi Taptite - M4 x 16 Lg. 405-01-050-010 Screw - Button Hd. - M5 x 10 Lg. 409-01-040-004 Screw - Socket Set - Flat Point - M4 x 4 Lg. 463-01-050 Domed Nut - M4 481-050 Washer - Plain - M5 481-060 Washer - Plain - M6 97-144-01 Spacer - Fold Plate 402-02-030-008 Screw - Countersunk Pozi Taptite - M3 x 8 Lg
Major
THIS SECTION IS CONTINUED ON THE FOLLOWING PAGES
FOLDER
Page 26 of 38

Text on page 27
FOLD PLATE - Deflect
PAPER
Page 27 of 38

Text on page 28
FOLD PLATE - Deflect
ITEM NO. QTY. PART NO. 97-040 97-059 1 97-061-02 1 97-065-02 601-086 613-379 405-01-040-016 405-03-006-250 613-378 97-142
FOLDER
DESCRIPTION
Positional Display PCB Digital Plate Label Top Cover Assy - Digital Deflector - Wide Bottom Cover Assy - Digital Deflector - Wide Display Bezel Battery - Duracell PP3 Screw - Button Hd. - M4 x 16 Lg. Screw - Button Hd. - 6-32 UNC x 0.25" Lg Battery Holder Bracket Assembly - Battery
Major
Page 28 of 38

Text on page 29
FOLD PLATE - Stop
PAPER
Page 29 of 38

Text on page 30
FOLD PLATE - Stop
ITEM NO. QTY. PART NO. 97-002-02 97-004-02 97-008-02 97-010-03 97-014 97-016 97-017 97-018 97-020-02 97-021 97-024-02 97-025 97-026 97-027 97-028 97-029-02 97-030 97-031 97-032 97-033 97-034-02 97-038 97-039 97-075 97-087 97-088 97-094-02 97-117 98-013-02 601-084 604-070 605-004 605-021 606-019 607-025 608-004 615-009 615-016 615-032 10 401-02-040-006 14 401-02-040-008 401-02-040-012 405-01-050-010 409-01-040-004 463-01-050 481-050 481-060 97-144-01 402-02-030-008
DESCRIPTION
Top Box - Stop - Wide Bottom Box - Stop - Wide Bottom Rail - Stop Stop Stop Guide Belt Clamp Guide Spacer Stop Spacer Top Rail Assy - Stop - Wide Control Dial Assembly Shaft -Blade Control Control Pulley 10XL Flanged Control Lock Control Lock Knob Tilt Lock Knob Idler Shaft Idler Reel Control Gear - Shaft Control Gear - Pot Potentiometer Bracket Latching Shaft Label - Pull Down to Lock Tilt Disc - Printed Pot & Lead Assy. Latching Bracket - Op Side Latching Bracket - Lay Side Spacer Plate - Top Rail (Stop) Bush - Bearing Anti-Static Brush - Wide Grommet - Ø12.7 X Ø15 X Ø20 X 1.6 Compression Spring Thrust Washer - Ø8 x Ø15.88 x 0.79 Thrust Washer Ø6.4 x Ø12 x 1.5 Hinge - Adjustable Black Acetyl Toothed Belt - 132XL Shoulder Bolt - Ø6(M5) x 16 Lg. Starlock Washer CIRCLIP- External - Ø6 Flex Loc Bush - M4 Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Pan Pozi Taptite - M4 x 8 Lg. Screw - Pan Pozi Taptite - M4 x 12 Lg. Screw - Button Hd. - M5 x 10 Lg. Screw - Socket Set - Flat Point - M4 x 4 Lg. Domed Nut - M4 Washer - Plain - M5 Washer - Plain - M6 Spacer - Fold Plate Screw - Countersunk Pozi Taptite - M3 x 8 Lg
Major
THIS SECTION IS CONTINUED ON THE FOLLOWING PAGES
FOLDER
Page 30 of 38

Text on page 31
FOLD PLATE - Stop
PAPER
Page 31 of 38

Text on page 32
FOLD PLATE - Stop
ITEM NO. QTY. PART NO. 1 97-040 1 97-059 1 97-062-02 1 97-066-02 1 601-086 1 613-379 8 405-01-040-016 6 405-03-006-250 1 613-378 1 97-142
FOLDER
DESCRIPTION
Positional Display PCB Digital Plate Label Top Cover Assy - Digital Stop - Wide Bottom Cover Assy - Digital Stop - Wide Display Bezel Battery - Duracell PP3 Screw - Button Hd. - M4 x 16 Lg. Screw - Button Hd. - 6-32 UNC x 0.25" Lg Battery Holder Bracket Assembly - Battery
Major
Page 32 of 38

Page 33 of 38

Text on page 34
ITEM
PART NUMBER
STACKER ASSEMBLY
QTY
DESCRIPTION
Major
STACKER BED - WIDE
STACKER GUIDE ASSEMBLY
STACKER BACKSTOP
STACKER EXTENSION
EXTENDED KNOB
UNIVERSAL KNOB
SHOULDER WASHER
Screw - Pan Pozi Taptite - M3 x 6 Long
Screw - Socket Set - Flat Point - M6 x 30 Long
Nut - Full - M3
Washer - Plain - M3
FOLDER
Page 34 of 38

Text on page 35
9-08-07 (EEC) 9-08-08 (USA)
PERFORATOR ASSEMBLY
PAPER
Page 35 of 38

Text on page 36
PERFORATOR ASSEMBLY
ITEM NO. QTY. PART NO. 2 98-003-02 1 98-007-02 1 98-008-02 1 98-009-02 1 98-050 1 98-051 98-013-02 1 98-018-02 1 98-019 1 98-021 1 98-022 98-032-02 2 98-037 98-048-02 98-049-02 1 601-096 1 603-057 2 604-056 10 401-02-040-006 4 404-01-050-016
FOLDER
9-08-07 (EEC) 9-08-08 (USA)
DESCRIPTION
Tie Bar - Perforator Input Bed - Perforator Upper Guard -Perforator Lower Guard - Perforator Perforator Scale - Metric - (EEC) Perforator Scale - Imperial - (USA) Anti-Static Brush - Wide STRIPPER - Perforator - Long. Smoother - Card Frame Pad Assy - Op Side Frame Pad Assy - Non Op Side Latching Shaft Assy - Wide Latch Bearing - Perforator Perforator Shaft Assy - Upper - Wide Perforator Shaft Assy - Lower - Wide End Tip Ø2.4XØ6.3X12.2 LG-BLK Tension Pin - Ø2.5 X 30 Lg Waved Washer - Ø24 X Ø17 X 3 Screw - Pan Pozi Taptite - M4 x 6 Lg. Screw - Socket C'snk Head. - M5 x 12 Lg.
Major
Page 36 of 38

Text on page 37
REAR DELIVERY - (Option)
PAPER
Page 37 of 38

Text on page 38
Major
ITEM
REAR DELIVERY - (Option)
PART NUMBER
QTY
DESCRIPTION
REAR DELIVERY FRAME
REAR DELIVERY COVER
MOUNTING HOOK
SUPPORT BRACKET
FLOATING DRIVE ASSEMBLY
DRIVE BELT - Rear Delivery
TRANSPORT BELT - Rear Delivery
SLIDE SHAFT - Rear Delivery
SUPPORT BARREL
SUPPORT STRAP
IDLER SHAFT - Delivery Idler
CORD ROLLER ASSEMBLY
SUPPORT SHAFT - Delivery
CONTROL COLLAR - Stacker
CATCHING FRAME - Delivery
STACKER ROLLER - Long
END CAP - Stacking Roller
AXLE - Stacking Roller
SLIDE FRAME ASSEMBLY - Low
COUNTER WEIGHT
UNIVERSAL KNOB
GROMMET FOOT
IDLER PULLEY - LIGHT DUTY
NYLON WASHER
CAPPED PUSH-ON FASTENER
NO GROOVE CIRCLIP
Screw - Pan Pozi Taptite - M4 x 6 Long
Screw - Pan Pozi Taptite - M4 x 8 Long
Screw - Socket Button Head - M4 x 8 Long
Screw - Socket Button Head - M6 x 10 Long
Screw - Socket Set - Flat Point - M4 x 16 Long
Nut - Full - M6 Nut - Full - M8
Washer - Plain - M4
Washer - Plain - M8
FOLDER
Page 38 of 38 ยท End of manual
Quick start
- Confirm the model: check that the model number on page four matches the number on the specification plate shown in section five.
- Note the serial number: write down the serial number stamped on the plate.
- Find the section: use the contents page and the numbered tabs on the outside edges of each page.
- Order with the assembly number: quote the major assembly number and description at the top of the page.
- Work safely: read the operators manual before any adjustment and disconnect the power supply before removing covers.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Not sure which power version applies | Separate 50 Hz and 60 Hz service sections | Use Services 50 Hz (EEC) or Services 60 Hz (USA) to match your machine. Page 5 |
| Cannot find a section quickly | Large manual | Use the numbered tabs positioned down the outside edges of each page. Page 5 |
| Part cannot be ordered individually | Component is part of a sub-assembly | Order the sub-assembly. Some components are not available individually. Page 3 |
| Worn or damaged parts | Normal wear | Section twelve lists the recommended spares and the sub-assemblies they belong to. Page 3 |
| Creasing heavier stocks | Standard blade set is not suited | Use the wider creasing blade set listed in the accessories section. Page 3 |
| Manual may not match the machine | Model number not confirmed | Confirm the model number matches the specification plate. The contents lists 904222 (EEC) and 954232 (USA). Page 5 |
Frequently asked questions
What model numbers are listed?
The contents page lists 904222 (EEC) and 954232 (USA). See page 5.
What assemblies are covered?
Main, delivery, feed bed, paper control, services, fold roller, fold plate, stacker, perforator and optional rear delivery assemblies. See page 5.
Are accessories listed?
Yes. Accessories in section eleven include the wider creasing blade set for heavier stocks. See page 3.
Where do I find recommended spares?
Section twelve lists recommended spares and the sub-assemblies they belong to. See page 3.
