Mounting Kit Manuals PDF Manual, page 1

Page 1 of 5

Mounting Kit Manuals PDF Manual, page 2
Text on page 2

Mounting Kit Manual – PN MK2000lit Issue 0, November 2005

Some HD modules came shipped with feet mounted directly to the bottom of the machine without an Interface Plate (Fig. A, item 1). This mounting kit is required to mount your module on an OD or HD punch. This manual covers all the kits available, if your kit does not have all the parts you require, see your dealer. Figure A shows you will find all of the parts in the large MK2000 kit. If you have another smaller kit, you did not require all these parts. Since this manual covers all the parts in kit MK2000, the smaller kit parts are covered as they are components of this Kit. This manual will refer back to this figure A to help clarify which parts are identified.

Page 2 of 5

Mounting Kit Manuals PDF Manual, page 3
Text on page 3

The first step to mounting your module to your punch is to determine which feet your module was shipped with. This will determine which parts to use. Note in Fig. B, this is an image of the short square feet (1) and the tall round feet (2). ♦ Short square feet: Attach the Interface Plate (Fig. A, item 1) directly to the bottom of your module with the 4 short flat head screws (Fig. A, item 2) as shown in Fig. B, item 4. An Allen wrench is provided to tighten screws. ♦ Tall round feet: Attach the Interface Plate (Fig. A, item 1) using the longer flat head screws (Fig. A, item 3) with the plastic spacers (Fig. A, item 4) as shown in Fig. B, item 3 between your module and Interface plate. An Allen wrench is provided to tighten screws.

Mounting the Module onto the HD-6500, HD-7000 or HD-7700; (If you have an OD-4000, OD-4012, or an OD-4800 proceed to the next chapter) Locate the Interface Blocks, screws, Allen wrenches (Fig A, items 5), These will be required in the next step.

Page 3 of 5

Mounting Kit Manuals PDF Manual, page 4
Text on page 4

HD-6500 and HD-7000 Instructions; HD-7700 Instructions; See Fig. C. See Fig. D. Locate the two top-rear-most screws Locate the two top-forward-most on the side of your HD-6500/7000. screws on the side of your HD-7700. Inserting the short end of the Allen Inserting the short end of the Allen wrench into the screw head, remove wrench into the screw head, remove the two screws. the two screws. Both HD-6500/7000 and HD-7700 Instructions cont... Store the two screws removed from the punch. Locate one of the Interface Blocks and orient it against the two now-available holes. Orient the block so that the interface block oval hole (Fig. C & D, item 1) is forward and the counter bores face out. To the right is an example of a counter bore. Use the longer ¼”-20 socket head screws (Fig. A in item 5) provided to secure the block to the machine with the short end of the Allen wrench. Tighten the rear screw first then the forward screw. Repeat this step on the other side of your punch with the other block.

Mount your module onto your punch using the 3-winged knobs (Fig. A, items 6) as shown in Fig. E, item 1. The 3-winged knob can be replaced with the button head screws (Fig. A, items 7) if required.

Page 4 of 5

Mounting Kit Manuals PDF Manual, page 5
Text on page 5

Mounting the Module onto an OD-4000, OD-4012, or an OD-4800; Locate the OD-HD Bracket and screw pack (Fig. A, item 8). Mount the RIGHT labeled bracket (Fig. F, item 1) with the screws (Fig. F, item 2) and Allen wrench provided. Repeat on LEFT side (Fig. F, item 3).

Special note for OD-4800 machines; Newer OD-4800 have extended shafts (Fig. G, item 1) to accommodate the new mounting kit (Fig. A, item 8). If your OD-4800 does not have theses extensions, contact your dealer for the OD-4800 shaft extension kit.

Page 5 of 5 · End of manual

Quick start

  1. Check which feet your module has: short square or tall round.
  2. Short square feet: attach the Interface Plate to the module with the 4 short flat head screws. Tall round feet: use the longer flat head screws with the plastic spacers.
  3. HD-6500/7000: remove the two top-rear-most side screws. HD-7700: remove the two top-forward-most side screws. Store the removed screws.
  4. Fit an Interface Block with the oval hole forward and counter bores out, using the longer ¼"-20 socket head screws. Tighten the rear screw first, then repeat on the other side.
  5. Mount the module on the punch with the 3-winged knobs (or the button head screws).
  6. For OD-4000, OD-4012 or OD-4800 punches, mount the RIGHT and LEFT labeled OD-HD brackets with the screws provided instead.

Troubleshooting

ProblemLikely causeFix (from the manual)
Kit is missing a part you needThe manual covers the large MK2000 kit. Smaller kits do not include every part.Check Figure A. If your kit does not have all the parts you need, see your dealer. Page 2
Not sure which parts to useThe parts depend on which feet the module shipped with.With short square feet, attach the Interface Plate directly with the 4 short flat head screws. With tall round feet, use the longer flat head screws and the plastic spacers. Page 3
Interface Block does not seat correctly on the punchThe block is turned the wrong way.Orient the block so the oval hole is forward and the counter bores face out. Tighten the rear screw first, then the forward screw. Page 4
3-winged knobs do not suit the setupKnobs may not fit your needs.The 3-winged knob can be replaced with the button head screws. Page 4
OD-4800 does not fit the bracket kitAn older OD-4800 does not have extended shafts.Newer OD-4800 machines have the extended shafts. Contact your dealer for the OD-4800 shaft extension kit. Page 5

Frequently asked questions

Which punches does this mounting kit work with?

HD-6500, HD-7000, HD-7700, OD-4000, OD-4012 and OD-4800. See page 3 and page 5.

My kit doesn't include every part shown. Is that a problem?

No. The manual covers the full MK2000 kit; smaller kits contain only the parts you need. If parts you require are missing, see your dealer. See page 2.

My OD-4800 has no shaft extensions. What do I need?

Newer OD-4800s have extended shafts for this kit. If yours doesn't, contact your dealer for the OD-4800 shaft extension kit. See page 5.