Paitec MX17000 User Manual, page 1

Page 1 of 37

Paitec MX17000 User Manual, page 2

Page 2 of 37

Paitec MX17000 User Manual, page 3
Text on page 3

Contents

Front Button & Remote Control 16

Fold Position Setting 23

Press Gap Adjustment 26

Page 3 of 37

Paitec MX17000 User Manual, page 4
Text on page 4

Introduction

Introduction

Welcome!

Thank you very much for selecting Paitec USA product!

This manual is prepared to provide you with guidelines on how to properly operate and maintain the MX17000. Please read this user manual before operating in order to prevent unexpected malfunction or damage. Please refer to the manual carefully and follow the instruction.

Copyright

Any of the contents should not be copied, re-printed or translated into other languages without Paitec USA approval.

Safety Precautions

Caution: Serious bodily injury or mechanical damage may result from insufficient attention to or incorrect compliance with warning messages with this symbol.

  • Do not attempt to disassemble or reassemble the machine. It may cause an electric shock or mechanical problem.
  • Disconnect the power immediately if liquid or a foreign object enter the inside of the machine.
  • Do not input metal or inflammable material into the inlet.
  • This manual is subject to be revised without notice.
  • Do not install the machine on the place as below.
  • Near window or places exposed to direct sunlight.
  • Where vibration is detected.
  • Where temperature changes suddenly or poorly ventilated.
  • Places exposed to hot or cold air directly.
  • Not solid enough or weak floor.

Page 4 of 37

Paitec MX17000 User Manual, page 5
Text on page 5

Introduction

Specifications

MX17000 is a heavy duty Standalone / Inline machine with following features

  • operating speed up to 17,000 sheets / hour (4-step speed adjustable), FRR

(Friction Reverse Roller) feeding system and double feed detection by ultrasonic

sensor. MX17000 ensures perfect feeding reliability and sealing quality even in high

speed operation with Duty Cycle up to 450,000 per month.

A4 / Letter / Legal

Up to 1,400 sheets

Max 17,000 sheets / hour

EZ, Z, C, V & Double

FRR (Friction Reverse Rollers)

Detects double feed by Ultrasonic Sensor

Reverse rollers to clear paper jam

Page 5 of 37

Paitec MX17000 User Manual, page 6
Text on page 6

Introduction

Description of Units

LCT InFeed Wire Guide

Start / Stop Button

LCT InFeed Paper Tray

LCA Lower Fold Plate

Page 6 of 37

Paitec MX17000 User Manual, page 7

Page 7 of 37

Paitec MX17000 User Manual, page 8
Text on page 8

Introduction

Description of Units

UCA Upper Fold Plate

Page 8 of 37

Paitec MX17000 User Manual, page 9

Page 9 of 37

Paitec MX17000 User Manual, page 10
Text on page 10

Installation

Enclosed Parts

Check out all parts are included after unpacking.

③ LCT Paper Tray

④ LCT Bottom Guide

⑤ V-Fold Guide (optional)

⑦ Remote Controller (optional)

  • Tools & Screws

① Screw M4X6L * 2pcs

② Thump Screw * 2pcs

③ Jam Removal Handle

Page 10 of 37

Paitec MX17000 User Manual, page 11
Text on page 11

Installation

Installation (Cabinet)

Place the Cabinet in a stable location.

Place MX17000 Main Body on the Cabinet. Align the Rubber Feet into the Guide Holes.

Page 11 of 37

Paitec MX17000 User Manual, page 12
Text on page 12

Installation

Installation (Table)

Slide the Cabinet Brace Guide into Silver Rivets as below.

Screw the Cabinet Brace Guide (Right) into Cabinet with (3) Black Screws M5*10

Page 12 of 37

Paitec MX17000 User Manual, page 13
Text on page 13

Installation

Installation (Table)

Screw the Cabinet Brace Guide (Left) with (3)Black Screws M5*10 as step 3 & 4.

We recommend to install the MX17000 on the optional Cabinet. If not, you must place the MX17000 on stable table since MX17000 is a heavy machine.

Page 13 of 37

Paitec MX17000 User Manual, page 14
Text on page 14

Installation

Installation (Main Body)

Fix the (LCT) Paper Tray Extender on the (LCT) Feed Table of machine with (2) screws (M4X6L)

Connect OP Post Harness Connector (2 pcs) to Main Body as below.

Page 14 of 37

Paitec MX17000 User Manual, page 15
Text on page 15

Installation

Installation (Main Body)

Fix the OP Post with Hand Screw (2 pcs)

Install Conveyor or Vertical Stacker into the machine as detailed in the respective Manual.

Page 15 of 37

Paitec MX17000 User Manual, page 16
Text on page 16

Operation

OP Panel

Ready

① Mode: Machine setting and working condition.

② Speed: Operation speed (adjustable, 11K / 13K / 15K / 17K)

③ Counter: Counter of current job. (resettable)

④ Total Counter: Counter of total operation. (non-resettable)

Page 16 of 37

Paitec MX17000 User Manual, page 17
Text on page 17

Operation

OP Panel

① Start / Stop: Press this button to Start & stop the machine; To Exit after programming setup and

To Stop the Feed Table (LCT) while moving down.

② Set: Sets and stores the selected function.

③ Printer Inline: Activate / deactivate Inline function.

  • To use Inline operation, you need inline kit (optional) & compatible printer.

④ Batch Counter: Enables you to set the number of forms that you wish to process in batch.

⑤ Speed (◀▶): Selects + or – to increase/decrease the speed (while machine is in stop mode)

⑥ Reset Counter: Clears the current job count on the display.

⑦ Thickness: Press to turn on or off the double detections using Ultrasonic Sensor Technology.

⑧ Jam Free: Assist with removal of paper jam at folding rollers or seal rollers.

⑨ Auto Start: Re-starts the process after selected time when the job reaches preset count.

⑩ Manual Feed: Use for single-sheet operation manually.

Page 17 of 37

Paitec MX17000 User Manual, page 18
Text on page 18

Operation

Front Button & Remote Controller

① Test: Test Button for single-sheet operation.

② Start / Stop: The same function of Start / Stop on the OP Panel.

③ Emergency: Stop operation of machine for emergency situation.

MX17000 is able to be operated by remote controller with Test & Start / Stop button.

Page 18 of 37

Paitec MX17000 User Manual, page 19
Text on page 19

Operation

Paper Loading

① MX17000 is able to handle the following size of forms.

If you use paper that is larger than or smaller than the specified paper, you may experience problems with the machine, such as paper jams.

① Before loading the forms onto the machine, please make sure all forms are aligned and

fanned. Please refer to the images below.

Page 19 of 37

Paitec MX17000 User Manual, page 20
Text on page 20

Operation

Paper Loading

To prevent paper bending when loading a big stack of paper in the (LCT) Feed Table, install the LCT Bottom Guide.

① Align the LCT Bottom Guide at the top of the (LCT) Feed Table as below.

② Insert the LCT Bottom Guide into the (LCT) Feed Table Hole as below.

Page 20 of 37

Paitec MX17000 User Manual, page 21
Text on page 21

Operation

Paper Loading

Adjust the Feed Table (LCT) Guide and Feed Table (LCT) Wire Guide positions to match the paper size.

① Rotate the LCT Fix Knob to CCW to unlock.

② Move the LCT Guide to adjust to match the paper size. After adjustment, rotate the LCT

Fix Knob to CW to lock.

Page 21 of 37

Paitec MX17000 User Manual, page 22
Text on page 22

Operation

Paper Loading

Adjust the LCT Guide and LCT Wire Guide positions to match the paper size.

③ Adjust the LCT Wire Guide position to match the paper size.

The paper must be positioned at the center of the Feed Table (LCT) as accurate as possible for smooth feeding.

Page 22 of 37

Paitec MX17000 User Manual, page 23
Text on page 23

Operation

Paper Loading

After adjustment, open the Safety Cover (Left) and load the paper on the Feed Table (LCT).

① Open the Safety Cover (Left) or no paper detected on the Feed Table (LCT), Feed Table

(LCT) goes down for paper loading. When the (LCT) lower to the bottom, load the paper on

② Close the Safety Cover (Left) after loading the paper. The Feed Table (LCT) automatically

Check that there is no foreign matter (adhesive, staple) on the paper before feeding. It may cause a malfunction and damage on the machine.

If the paper is not in good condition (paper curl, wet ink, etc.), it may cause miss-feeding or paper jam.

Page 23 of 37

Paitec MX17000 User Manual, page 24
Text on page 24

Operation

Fan Blower

The MX17000 has a Air blower to the Feed Table (LCT) to assisted paper feeding. Use the Fan Volume Control Knob to adjust the fan speed.

Fan Volume Control Knob

If the fan speed is too high, the paper may separate too much for paper feeding. Adjust the fan speed according to the paper weight.

Page 24 of 37

Paitec MX17000 User Manual, page 25
Text on page 25

Operation

Fold Position Setting

UCA (Upper Cassette, 1 st fold) Fold Position Setting

① Open the Safety Cover (Right) and pull out the UCA as below.

UCA

② Rotate the Locking Knob counter clockwise to unlock, then adjust the fold position with

Fold Position Knob. Lock the Locking Knob after adjustment.

Page 25 of 37

Paitec MX17000 User Manual, page 26
Text on page 26

Operation

Fold Position Setting

LCA (Lower Cassette, 2 nd fold) Fold Position Setting

① Pull out the LCA as below.

LCA

Page 26 of 37

Paitec MX17000 User Manual, page 27
Text on page 27

Operation

Fold Position Setting

LCA (Lower Cassette, 2 nd fold) Fold Position Setting

② Rotate the Locking Knob to CCW to unlock

③ Adjust the fold position with Fold Position Knob. Lock the Locking Knob after adjustment.

Page 27 of 37

Paitec MX17000 User Manual, page 28
Text on page 28

Operation

Press Gap Adjustment

MX17000 is able to be adjusted the Press Gap by adjusters (2 pcs)

① “+” means increasing the press gap

② “-” means decreasing the press gap

③ Put a tool into the Adjuster & rotate CW / CCW to adjust the gap

You must set the same value (“+” or “-”) on upper & lower Press Gap Adjuster.

We recommend you to keep the default position of Press Gap Adjuster. If there is an issue to change the gap, please contact local dealer or service company to adjust the Press Gap with engineer.

Page 28 of 37

Paitec MX17000 User Manual, page 29
Text on page 29

Operation

Operation

Load the paper on the Feed Table (LCT).

Adjust the fold position of UCA / LCA as your desire fold type.

Press the Thickness button on the OP Panel to detect the thickness of the paper.

① The MX17000 has an ultrasonic sensor to detect paper thickness & prevent double

When you press the Thickness button, a sheet of paper is fed and automatically

detects the paper thickness.

② When the double detection function is activated, the Thickness lamp is turned on

Pressing the button again will turn off the lamp and double detection will be disabled.

Press Start / Stop button for operation

① Operation will continue to run until finishing all of the paper loaded on the Feed Table

(when Batch Count / Auto Start function is activated, it depends on the amount of count

② Press Start / Stop button during machine operation, the machine will stops.

If an emergency occurs during operation, press the emergency switch on the front of the unit to stop the machine.

Page 29 of 37

Paitec MX17000 User Manual, page 30
Text on page 30

Operation

Functions

You can set the Batch Count of a job to be run. For example, if you set the count on

100, machine will stop operating when the job reaches 100. Press Start/Stop button

again, machine will start to finish another 100.

① Press Batch Count button and the LED will light on

② Select job volume by using ◀▶ button.

  • Press the button on by one, count will change by 1 and if you press for more than one

second, the count will change by 10/second.

  • Press Batch Count button, the count will change 50~100.

③ Press Set button and check the number displayed on the panel.

  • You can set the counter up to 500 sheets.

Auto Start: this function allow you to setup the time for the machine to be pause (Time

Interval) at the end of each batch and Start again for the next batch.

① Set the Batch Count first. Auto Start is only available when Batch Count is activated.

② After pressing Auto Start, “Time Interval” will be shown on the OP. Set the interval time

③ Press Set to save the value. (Max 99 seconds)

④ Machine will run up to the number Batch Count as setting. Pause at (Time Interval) as

setting & Start again automatically.

⑤ If you turn off and on the machine, you have to set the function again.

Page 30 of 37

Paitec MX17000 User Manual, page 31
Text on page 31

Operation

Functions

The Thickness function detects the thickness of the paper through the ultrasonic sensor

to prevent serious paper jams due to double or multi feeding.

① Press the Thickness button, 1 sheet is fed to detect the thickness of the paper.

② When the double detection function is activated, the Thickness lamp is turned on

Pressing the button again will turn off the lamp and double detection will be disabled.

③ When the machine is detecting double feeding while using the function, the machine

will stop operating with the message "Double Feed".

If you turn Off the machine or change the paper type, be sure to reset the paper thickness after turn On by pressing the Test button.

Manually handling single sheet job for damaged paper & small amount of work.

① Holding down the Manual Feed button on OP Panel & Feed a pre-fold form in the entry

slot on the exit path of the machine.

② Press the other Manual Feed (red) button on the side of the front cover. The pre-fold

form will enters into the press rollers for sealing and is ejected.

③ Keep holding down both Manual Feed button until the form is rejected on the exit path.

Be careful not to get your hands caught in the press roller inside the Machine while using Manual Feed Function.

Page 31 of 37

Paitec MX17000 User Manual, page 32
Text on page 32

Operation

Functions

In case the paper is jammed at folding or press rollers, machine will stop with error message. If you press Jam Free button, machine will try to reverse direction to release the jam in the rollers then you will have to remove by hand through the top cover. Note: The feeding unit motor will not run during this operation.

The Jam Free feature does not resolve all paper jams. In the event of a serious paper jam, place the Jam Removal Tool in the Jam Removal Hole on the back of the machine to remove the paper jam.

※ How to manually clear a jam by using the jam removal tool, turn in the direction

Be sure to remove the tool before operating the machine.

Page 32 of 37

Paitec MX17000 User Manual, page 33
Text on page 33

Maintenance

Paper Jam Remove Options

UCA Paper Jam (Upper Fold Plate Cassette)

① Open Safety Cover (Right)

② Pull out the UCA & remove the paper jam.

LCA Paper Jam (Lower Fold Plate Cassette)

① Pull out the LCA.

② Remove the paper jam.

Press Roller Paper Jam

① Try to remove the jam by using the Jam Free function.

② If the jam is not cleared by using the Jam Free function, please use the jam removal

tool to manually remove the jam.

Turn off the power before remove any jams.

Page 33 of 37

Paitec MX17000 User Manual, page 34
Text on page 34

Maintenance

Trouble Shooting

① Check whether the power cable is properly connected.

② Check the power supply.

③ Check if the “RED” Emergency Button is pushed.

① Check the fold setting on the two fold plates (Upper and Lower Cassette).

② Check the direction of paper on the LCT (Feed Table).

Power On, but No Start

① Check the “Mode” on the OP Display is “Ready” condition.

② Check out the Safety Covers (left & right) are closed.

③ Check out the LCA / UCA is closed.

④ Check out if there is a paper jam inside of the machine.

Frequent Double or Multiple Sheet Feeding

① Check the condition of Infeed Roller Set. Try to clean them or replace all three

rollers all at once if they are worn out.

② Check whether the adhesive on the sealer paper is too thick or too tacky.

③ If the paper is curled or the ink does not dry out after printing, the paper may not be

④ After power On or after changing the form, Press Thickness Button to re-calibration.

If the errors keep occurring, please contact the local dealer or service company.

Page 34 of 37

Paitec MX17000 User Manual, page 35
Text on page 35

Maintenance

Cleaning

The feeding rollers consist of three different rollers as Pickup / Feed / Separation Roller.

If the rollers are contaminated or worn out, feeding failures might occur. Please

clean the rollers periodically. If they are worn out, replace all three of them at once.

Note: Using Denatured alcohol. Do not use regular roller cleaner solutions.

Separation Roller (below of Feed roller)

① Remove the Snap-Ring which is holding the roller on the shaft.

② Remove the roller & clean by a soft clothing with Denatured alcohol.

③ After cleaning, put the roller back on the shaft and reattach the Snap-Ring.

Page 35 of 37

Paitec MX17000 User Manual, page 36
Text on page 36

Maintenance

Cleaning

Since Pressure seal forms leave paper dust, ink and toner residues, it is very important

to occasionally clean the surface of each fold roller to maintain its best condition for

① Open the Safety Cover (Right) & pull out UCA. (Upper Fold Plate Cassette)

② Clean each roller by a soft clothing with Denatured alcohol. Rotate the roller to clean all

③ Close the UCA & Safety Cover (Right).

Please do not use any other substance when cleaning the surface of the fold rollers as it may damage the Polyurethane.

Page 36 of 37

Paitec MX17000 User Manual, page 37

Page 37 of 37 ยท End of manual

Quick start

  1. Place the MX17000 on the optional cabinet or a stable table, fit the paper tray extender and connect and fix the OP post.
  2. Adjust the LCT guide and wire guide to the paper size so the stack sits at the center of the feed table.
  3. Open the left safety cover, load aligned, fanned paper on the feed table and close the cover so the table rises.
  4. Set the UCA (1st fold) and LCA (2nd fold) fold positions with the fold position knobs and lock the locking knobs.
  5. Press Thickness to feed one sheet and turn on ultrasonic double-feed detection.
  6. Press Start / Stop to run; use the red emergency button on the front to stop in an emergency.

Troubleshooting

ProblemLikely causeFix (from the manual)
No powerPower cable not connected, no power supply, or red emergency button pushedCheck the power cable and power supply, and check whether the red emergency button is pushed. Page 34
Incorrect foldingWrong fold setting on the fold plates or paper loaded in the wrong directionCheck the fold settings on the upper and lower cassettes and the paper direction on the feed table. Page 34
Power on, but no startMachine not in Ready mode, a cover or cassette open, or a jam insideCheck that the display shows Ready, the left and right safety covers and LCA/UCA are closed, and no paper is jammed. Page 34
Frequent double or multiple sheet feedingDirty or worn infeed rollers, adhesive too thick or tacky, curled paper or wet inkClean the infeed rollers or replace all three at once, and press Thickness to recalibrate after power-on or a form change. Page 34
Paper separates too much while feedingFan blower speed too highLower the fan speed with the Fan Volume Control Knob to suit the paper weight. Page 24
Paper jam at the fold or press rollersPaper jammed in the rollersPress Jam Free to reverse the rollers and remove the paper by hand. For a serious jam, turn off the power and use the jam removal tool in the hole on the back; remove the tool before operating. Page 32

Frequently asked questions

How fast is the Paitec MX17000?

Up to 17,000 sheets per hour, with four speed steps (11K, 13K, 15K, 17K). See page 16.

What paper sizes and fold types does it support?

A4, Letter and Legal, with EZ, Z, C, V and double folds. The feed table holds up to 1,400 sheets. See page 5.

Should I change the press gap?

The manual recommends keeping the default press gap. If it must be changed, contact your dealer or service company. Upper and lower adjusters must be set to the same value. See page 28.

How do I set a batch count?

Press Batch Count, choose the quantity with the arrow buttons and press Set. The counter can be set up to 500 sheets. See page 30.

What should I use to clean the rollers?

Use a soft cloth with denatured alcohol. Do not use regular roller cleaner solutions. See page 35.