

Page 1 of 17

Text on page 2
PROFESSIONAL SERIES
MODEL 850, 855, 860
MAT CUTTER
INSTRUCTION AND OPERATION MANUAL
Professional mat cutting system with aluminum baseboard, magnetic production stop, 32 in (81 cm) removable squaring arm, plus dual straight and bevel cutting heads
For best results use only authentic Logan blade #267
CAUTION!!
MAT CUTTING BLADES ARE SHARP
Mat border calculator Mobile app
ID Number (on bottom of board)
Date (on bottom of board)
Logan Graphic Products, Inc.
1100 Brown Street Wauconda, IL 60084 USA Phone 847-526-5515 Fax 847-526-5155 cs@logangraphic.com LoganGraphic.com
Page 2 of 17

Text on page 3
INTRODUCTION
The Logan Platinum Edge Mat Cutter (Model 850, 855 & 860) is designed specifically with the framer in mind. All the materials are heavy-duty to withstand the rigors of professional mat cutting and to provide the accuracy framers demand.
Features include super-smooth cutting head glides, 4- and 8-ply cutting capability, quick-change magnetic blade cartridges, micro-adjustable moving magnetic stop, 32” (81cm) removable scaled squaring arm, and heavy-duty all-metal construction with aluminum base. Use Logan Replacement Blade Model 267.
We are confident that the quality, accuracy and dependability of the Platinum Edge will be everything you expect in a professional mat cutter.
This instructional manual is written to acquaint you thoroughly with this product. Referred to at the outset, it will answer many questions that may arise during use. You will find that the time taken will be well worth it and you will be cutting top quality mats in no time.
ta b le o f contents
Out Of Box Set Up..............................................................................................................................1 Changing/Installing Mat Cutter Blades.................................................................................................2 Cutting A Beveled Mat.........................................................................................................................3 Line to Line Method......................................................................................................3 Production Stops Method...............................................................................................4 Platinum Edge Precision Mat Cutter Diagram.......................................................................................6 Sizing The Mat Board..........................................................................................................................7 Cutting V-Grooves...............................................................................................................................8 Making Adjustments...........................................................................................................................8 Re-squaring the Squaring Arm......................................................................................8 Cutting Head................................................................................................................9 Bevel Blade Tip Adjustment Screw.................................................................................10 Production Stop Micro-Adjustments................................................................................10 Mat Guide....................................................................................................................10 Re-Parallel the Mat Guide.............................................................................................10 Troubleshooting..................................................................................................................................11 More Great Logan Products.................................................................................................................12 Warranty............................................................................................................................................ 13
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 3 of 17

Text on page 4
Out Of Box Set Up
Above: Additional parts included in this package: Four Allen wrenchs, sizes 1/8”, 5/32”, 5/64” & 1/16”, Handle Bar Lift Knob and screw, two replacement blade packs (5 ct. each)
The Platinum Edge Mat Cutter has been aligned and calibrated at our facility before shipping. With a few simple steps, you will be able to set up your mat cutter and begin production immediately.
Remove the Platinum Edge Mat Cutter from the box and unwrap the pieces carefully. Your Platinum Edge should be set up on a flat, stable work table, aligned so that you can easily access the handle bar lift and cutting head (Figure 2.1). Follow the assembly guide (Figure 2.2).
ASSEMBLY INSTRUCTIONS
(See page 6 for parts identification)
- Insert Right Side Squaring Arm into Squaring Arm Mount
- Hook the Squaring Arm Strut onto the Strut Bracket
- Attach the Handle Bar Lift Knob using the enclosed screw and 5/32” Allan wrench
Figure 2.2 Assembly Guide
IMPORTANT: Do not oil or lubricate the cutting head or guide rail.
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 4 of 17

Text on page 5
Changing and Installing Mat Cutter Blades
bevel blade holding knob
A note about Mat Cutter Blades: They are sharp. Super sharp. Imagine a sharp thing and then multiply it by a power of three. That sharp. So, be careful.
Single Bevel
Bevel Cut Blade Magazine
scribe line
blade depth adjustment screw
The Platinum Edge Mat Cutter uses Logan Blade Model 267, which is a 0.012” thick double bevel blade. However, any blade that is 3/4” in height may be used, as long as the blade depth and production stops are adjusted accordingly for accurate results (See “Making Adjustments” starting on Page 16). Whether you use single bevel blades or double bevel blades is really up to you, but either version can be purchased from an authorized art materials dealer.
Double Bevel
sharp edge
Straight Cut Blade Magazine
Always use a sharp blade when cutting mats. Signs your blade may be too dull include ragged cuts or a tendency for the blade to tear the mat rather than slice it. When a blade becomes dull you will need to remove it and either exchange it for a new one or, in the case of double bevel blades, reverse the blade to use the as-yet-unused side. To remove a blade magazine from the blade carrier, first loosen the bevel blade holding knob located beneath the front handle of the blade carrier (Figure 3).
Take hold of the black adjustment screw at the rear of the magazine and pull the magazine out. If the magazine does not come out smoothly, loosen the thumb screw a bit more.
Setting the Bevel Blade Depth
NOTE: It is important to distinguish the difference between the Bevel Cut and Straight Cut blade magazines. Identify the scribe line on the Bevel Cut Blade Magazine. This inserts on the left side (bevel side) of the cutting head.
Place a fresh blade on the magazine with the sharp edge down – the magnet will hold it in place (Figure 4). Insert the magazine into the blade holder slot until the rear of the magazine is flush with the rear of the blade holder, then tighten the blade holding knob securely. You will be able to feel where the blade holding knob falls into the divot machined into the blade magazine (Figure 5).
Blade depth adjustments are made by loosening the blade holding knob slightly and turning the blade depth adjustment screw in or out. Each blade should be set so it only just cuts through the mat being cut and slightly scores the slipsheet.
TIP
The bevel cut blade magazine features a scribe line (Figure 4) as a suggested place to align the rear of the blade. This line was factory tested with a commonly available 4-ply mat board. Your matboard thickness may vary, in which case the blade will require adjustment as described above.
Inserting the Bevel Blade Holding Magazine
Inserting the Straight Blade Holding Magazine
CAUTION!!
MAT CUTTING BLADES ARE SHARP
bevel blade holding knob
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 5 of 17

Text on page 6
Cutting a Beveled Mat
Line to Line Method
Bevel cutting is done from the back side of the mat with the colored side down. Always use a slip sheet of scrap mat board beneath the mat you intend to cut in order to provide a crisp edge (Figure 6).
A slip sheet usually measures about 6 inches wide and is at least a few inches longer than the mat you intend to cut. The bevel blade should extend far enough so that it slices through the mat you are cutting and then just score into the slip sheet.
TIP
After you have cut a few mats, you may wish to move the slip sheet or flip it so that the blade does not follow the same slip sheet furrows. Having fresh mat board beneath the surface you intend to cut helps to provide a crisply cut edge.
Line to Line Method
Step 1 Set the mat guide only at desired border size like 2” for this example (Figure 7).
Step 2 Insert a mat board blank, color side down, on top of a slip sheet. Using a pencil, mark lines along the left side of the cutting bar from end to end of the mat board blank and repeat for all four sides.
TIP
A suggestion to learn where to start and stop with your blade: Mark out four even size borders on a mat blank. Then set your production stops (see page 7) to cut that same size even border. Cut the mat using the production stops. While cutting, watch and take mental note of where the blade enters and exits the mat in relation to the pencil lines while using the production stops. Seeing where the blade starts and stops using the production stops will teach you where to manually duplicate these entry and exit points when cutting line to line.
Step 4 Repeat this process for the next side, and stop to inspect the corner. If the corner is hung up and the window is not dropping out, OR if there is significant overcut in the corners, then adjust where you start and stop.
Blade inserts 3/16” above pencil line
Step 3 Slide the cutting head to the top line and position it so the entry point of the blade tip is roughly 3/16” above the pencil line (Figure 8). Rotate the blade holder to insert the blade, and pull back to cut while applying steady, even pressure, stopping when the tip of the blade passes the bottom pencil line by roughly 3/16”.
TIP
The mat cutting technique described above (without production stops or stop/start indicators) is used by professional framers. Although it takes some practice to perfect, the tips provided here combined with patience and persistance will help you quickly master the technique.
continued on page 4
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 6 of 17

Text on page 7
Cutting a Beveled Mat
Line to Line Method
- While rotating the blade into the mat, hold the cutting head still to prevent it from creeping forward upon insertion, which can cause an overcut.
TIP
- Maintain constant downward pressure on the bevel blade holder throughout the cut to ensure the blades passes through the mat board.
- Pushing down on the long handle bar during cutting is unnecessary and not recommended.
- Cutting 8-ply or Double Thick Mat Board - After increasing the blade depth, use a piece of test 8 ply mat board to mark out and line to line cut one corner that can be inspected. Do not use the production stops for this test cut. Cut from line to line, starting and stopping the blade approximately 3/8” past the marked lines. Inspect the slip sheet to see you are just barely scoring into the surface. Inspect the corner on the test mat to check for overcuts.
- Cleaning debris from under the cutting bar - Occasionally some debris may collect under the cutting bar, which could cause cutting inconsistencies. To remove the debris, use a clean cloth, soft brush or compressed air. Do not use cleaning fluids that may leave a film on the mat cutter. This film may damage the matboard.
Cutting a Beveled Mat
Production Stops Method
Using the ruler guides on the left side squaring arm (Figure 9), cutting head (Figure 10), and clamp rail (Figure 11), set the desired border width for your finished mat. The example shown is for cutting a mat with a 2” border.
Standing at the end of the mat cutter, use the handle bar lift to raise the guide rail above the surface of the base (Figure 12).
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 7 of 17

Text on page 8
Cutting a Beveled Mat
Production Stops Method
Squaring Arm
Slide the mat and slip sheet beneath the guide rail and align the lower corner of the mat you intend to cut at the junction of the squaring arm and mat guide. It is important to make sure the mat you are about to cut sits squarely against the squaring arm and the mat guide. Lower the lifter bar mechanism to secure the mat in place for cutting (Figure 13).
Slide the cutting head up the guide rail until the magnetic moveable stop catches the cutting head. The black foot of the stop should be in an elevated position to avoid catching on the slip sheet.
Slide the cutting head down the guide rail until the black foot of the automatic stop has gone past the upper edge of the slip sheet and then drop it down into position. When the foot catches the edge of the mat you are about to cut, rotate the cutting head down into the mat, starting your cut (Figure 14).
Squaring Arm
Pull the cutting head towards you, and the magnetic moveable stop will automatically release. Continue the cut with a steady pull until the cutting head makes contact with the lower stop. Rotate the blade out of the mat. Raise the handle bar using the handle bar life (Figure 12) to release the mat, turn the mat 90 degrees, align the corner of the mat back into the corner of the mat stop and mat guide and repeat the cutting process.
- While rotating the blade in, hold the cutting head still to prevent it from creeping forward upon insertion which can cause an overcut.
- Maintain constant forward pressure on the bevel blade holder throughout the cut to ensure the blades passes through the mat board.
TIP
- Pushing down on the long handle bar during cutting is unnecessary and not recommended, as it may cause hooks and curves in the mat opening.
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 8 of 17

Text on page 9
Platinum Edge Precision Mat Cutter
Diagram
Left Side: Bevel Cutting
Right Side: Straight Cutting
1 Left Side Squaring Arm 2 Mat Guide 3 Handle Bar 4 Base 5 Cutting Bar 6 Support Arm 7 Hinge 8 Cutting Bar Bracket
9 Magnetic Moveable Stop 10 Cutting Head 11 Squaring Arm Mount 12 Right Side Squaring Arm 13 Squaring Arm Stop 14 Bottom Stop 15 Handle Bar Lift 16 Squaring Arm Strut
17 Strut Bracket 18 Bevel Blade Holding Knob 19 Bevel Blade Holding Magazine 20 Straight Blade Holding Magazine 21 Straight Blade Holding Knob 22 Lockdown Pin
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 9 of 17

Text on page 10
Sizing Mat Board
Full size mat boards can be cut down to a desired size using the straight blade side on the cutting head. The removable squaring arm is helpful for squaring and sizing the mat (Figure 15).
Set the squaring arm stop for the measurement you want and tighten the knob (Figure 15).
TIP
Full sheet mat board is most often not square when purchased new. Leaving any factory corners can produce unsquare mats. If you need to square the board, trim a small amount off all four sides of the mat board using the straight cut side. When trimming, cut opposite sides first and then the remaining opposite sides. (trim each long side first then trim the short sides)
Remove the mat guide and the slip sheet. Place the mat board under the cutting bar and against the squaring arm and squaring arm stop (Figure 16). The lower stop should be moved all the way to the bottom of the guide rail bar – it does not need to be tightened.
Adjust the straight cutting head blade so it will cut about 1/32nd of an inch deeper than the mat board you are cutting. To cut, position the cutting head above the top edge of the mat board and rotate the straight cutting head down as far as it will go. Lock it in position with the lockdown pin for the cutting process (Figure 17).
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 10 of 17

Text on page 11
Cutting V-Grooves
For professional quality V-Grooves, the Logan Model 706 Universal V-Groover is compatible with Model 850. It is available from picture frame suppliers and art supply dealers. See Page 21 for more information.
Above are two examples of artwork that are enhanced with V-Groove mats
time to time, you may need to make adjustments to your Platinum Edge Mat Cutter. The following
Making Adjustments From
categories will guide you through the process of adjusting your mat cutter if some fine tuning is needed.
Re-squaring the Squaring Arm
It is possible over time for the squaring arm to come slightly out of square to the cutting bar. In this situation, you will need to re-square the squaring arm.
Before making any adjustments, check the squareness of the machine with this test. You will need an L shaped carpenter’s square found in any hardware store.
Insure that you have the long 32” squaring arm tightly attached to the squaring arm mount.
Remove any mat board or slip sheet material from the machine.
Slide the cutting head to the far end of the cutting bar out of the way.
Place the L shaped carpenter’s square into the machine into the 90 degree corner formed by the cutting bar and the squaring arm. (Fig 19 & 20)
Check the relationship of the L shaped carpenter’s square to the cutting bar and squaring arm. It should fit tightly with no movement. If there is movement, determine which direction the squaring arm needs to move to be square again and allow the L shaped carpenter’s square to snugly fit into the machine with no movement.
continued on page 9
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 11 of 17

Text on page 12
Making Adjustments
Figure 21 - Strut Bracket
Loosen the squaring arm strut bracket screws (Figure 21) and gently tap the bracket forward or backward to pull or push the squaring arm the direction it needs to go to be square again. Moving the strut bracket up or down slightly will push or pull the angle of the squaring arm back into square. (Fig 22).
Once the squaring arm is square to the L shaped carpenter’s square, re-tighten the squaring arm bracket in place. The machine is now re-squared.
If the cutting head begins to wobble side-to-side, there are three setscrews to tighten.
Caution: do not over-tighten these screws.
On the right side of the cutting head there are two recessed holes. One is to the left of the 90 degree blade carrier behind the knurled screw and one is to the right of the blade carrier behind the extended blade (remove blade before adjusting) (Figure 23).
With the Allen wrench provided, slightly tighten the front bushing screw. After each adjustment, slide the cutter back and forth until some resistance is felt. If there is too much resistance, loosen the screw very slightly so the cutting head slides easily. Repeat this process on the rear bushing. The third adjustment screw for the cutting head is in a recessed hole on the top of the head (Figure 24).
This tightens the roller bearing. Again, slightly tighten the bearing screw and check for resistance by sliding the cutting head. As soon as resistance is felt, loosen the setscrew slightly.
Caution: do not over-tighten these screws or damage to the bearing or bushings rmay result.
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 12 of 17

Text on page 13
Making Adjustments
Blade Tip Adjustment Screw
Bevel Blade Tip Adjustment Screw
If you are experienceing hooks or curves in your cuts even though the blade depth is set properly so it only scores into the backing sheet, an adjustment to the blade tip adjustment screw may be needed (Figure 25). Remove the bevel blade magazine and the blade and locate the small screw on the magazine located near where the tip of the blade rests. Using the Allen wrench provided, turn the screw in slightly to put more pressure on the blade tip while cutting. DO NOT OVERTIGHTEN. Too much pressure from this screw can drive the blade into the cutting bar. Too little pressure from this screw can create “slack” in the blade which can allow it to flex while cutting which can produce hooks or curves.
Production Stop Micro Adjustments
If you are experiencing over cuts or under cuts using productin stops even though the blade depth is set properly so it only scores into the backing sheet, adjustments to the production stops may be needed. On the mat guide, bottom stop and magnetic movable stop, you will find a small knob that moves the indicator plate over the scale. This indicator plate can be moved slightly to correct an over cut or under cut. For example, if you are experiencing an over cut at the start of a 2” border cut using the magnetic movable stop, turn the micro adjustment on the magnetic movable stop to slightly less than 2” and then loosen and adjust Mat Guide Mat Guide Micro the entire magnetic movable stop back to the 2” mark. This will Lock Knob Adjustment Knob remove some or all of the over cut allowing you to still set the stop Indicator properly at the 2” mark each time. For under cuts, turn the micro adjustment on the magnetic movable stop to slightly more than 2” and then loosen and adjust the entire magnetic movable stop back to the 2” mark. This will remove some or all of the under cut allowing you to still set the stop properly at the 2” mark each time.
Fine tuning the width of the border is done on the mat guide. If you need to make the border width a bit narrower, turn the mat guide micro adjustment knob counter-clockwise. Conversely, turning the knob clockwise will widen the border width slightly (Figure 26).
Re-Parallel the Mat Guide
If the Mat Guide is not parallel to the cutting bar, it can be adjusted to re-parallel.
- Move top stop to end of machine (Figure 27).
MOVE TOP STOP
MOVE TOP STOP
- Loosen mat guide knob.
- Slide mat guide against cutting bar and tighten.
- Look for gaps.
- To eliminate gap, loosen mat guide knob and turn screw using allen wrench provided. Use Screw A if gap is near the end of the machine (Figure 27). Use Screw B if gap is near the mat guide knob (Figure 28).
- Retighten mat guide knob and check for gaps.
CAUTION!!
MAT CUTTING BLADES ARE SHARP
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 13 of 17

Text on page 14
Troubleshooting
Cutting without a slip sheet (Page 3) Slip sheet is worn out (Page 3) Dull or chipped blade (Page 2) Inconsistent pressure being applied on the cutting head while cutting (Page 4) Putting unneeded pressure down onto the handle bar (Page 4)
Overcut at the start of the cut
Allowing the cutting head to “creep” forward upon blade insertion (Page 4) Starting the cut too far past the pencil line (Page 3) Too much blade depth (Page 2) Production stop not set properly or needs micro adjustment (Page 10)
Overcut at the end of the cut
Cutting too far past the bottom pencil line (Page 3) Too much blade depth (Page 2) Production stop not set properly or needs micro adjustment (Page 10)
Blade not cutting through material
Pushing down on the handle bar while cutting (Page 4) Inconsistent pressure being applied on the cutting head while cutting (Page 4) Debris caught under the cutting bar (Page 4) Blade depth set too shallow (Page 2)
Cutting through the mat in some areas but not in others
Pushing down on the handle bar while cutting (Page 4) Slip sheet not the full length of the mat being cut (Page 3) Inconsistent pressure being applied on the cutting head while cutting (Page 4) Debris caught under the cutting bar (Page 4)
Hook in corner or long curve in the cut
Too much blade depth allowing the blade tip to flex (Page 2) Dull blade (Page 2) Pushing down on the handle bar while cutting (Page 4) Slip sheet not the full length of the mat being cut (Page 3) Inconsistent pressure being applied on the cutting head while cutting (Page 4) Possible adjustment needed to the blade tip adjustment screw (Page 10)
Cutting heads hard to pull when cutting
Dull blade (Page 2) For bevel cutting, too much blade depth (Page 2) For straight cutting, did not remove slip sheet before cutting (Page 7) Possible adjustment needed on cutting head tension screws (Page 9)
Borders of mats inconsistent size from one end to the other
Not placing the mat and slip sheet tightly against the parallel mat guide (Page 5) Mat guide not parallel and needs adjustment (Pages 8-9) Mat board not squared properly before cutting (Page 7)
Machine not producing square cuts when downsizing mat board
Not placing the mat squarely against the squaring bar while cutting (Page 5) Squaring arm no longer square and needs adjustment (Pages 8-9) Trim all four sides of an unsquare mat board before using (Page 7)
Cutting head loose on the rail
Possible adjustment needed on cutting head tension screws (Page 9)
Production stops producing over or under cuts
Blade depth set too deep or too shallow (Page 2) Possible micro adjustment needed on the production stops (Page 10)
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 14 of 17

Text on page 15
Warr ant y
Logan Graphic Products, Inc. (“Logan”) warrants the Platinum Edge (Models 850, 855 & 860) to be free from defects in parts and workmanship for a period of two years from the date of original purchase. Logan warrants that it will either repair or replace, at its sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied. Be advised that any Logan products purchased as “new” from an unauthorized dealer, such as an online auction site or similar, may be void of their warranty.
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 15 of 17

Text on page 16
Logan Quality Commitment
Logan Graphic Products, Inc. is committed to delivering products that work and exceed our customers’ expectations. If you are dissatisfied with your tool’s performance, do not understand the directions, or feel that you are not getting the results you expected, DON’T GIVE UP! Contact us by email or phone, and let us help solve your problem. We are here for you, and want you to be thrilled with your Logan purchase.
email: cs@logangraphic.com phone: 800 331 6232 • 847 526 5515
Logan Graphic Products, Inc. • 1100 Brown Street, Wauconda, IL 60084 USA • Phone (847) 526-5515 Fax (847) 526-5155 • www.logangraphic.com
Page 16 of 17

Page 17 of 17 ยท End of manual
Quick start
- Set the cutter on a flat, stable table where you can reach the handle bar lift and cutting head.
- Insert the right side squaring arm into the squaring arm mount and hook the squaring arm strut onto the strut bracket.
- Attach the handle bar lift knob with the enclosed screw and the 5/32" Allen wrench.
- Load a Logan #267 blade, sharp edge down, on the bevel magazine (the one with the scribe line) and insert it on the left side of the cutting head; tighten the holding knob.
- Set blade depth so it just cuts through the mat and lightly scores the slip sheet.
- Set the mat guide to your border width, place the mat color side down on a slip sheet, and cut using pencil lines or the production stops.
- Do not oil or lubricate the cutting head or guide rail.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Overcut at the start of the cut | Cutting head creeps forward when the blade is inserted, starting too far past the pencil line, too much blade depth, or a production stop that needs micro adjustment. | Hold the head still while rotating the blade in, start about 3/16" above the line, reduce blade depth, or micro-adjust the stop (page 13). Page 14 |
| Overcut at the end of the cut | Cutting too far past the bottom pencil line, too much blade depth, or production stop not set properly. | Stop about 3/16" past the line, reduce blade depth, and check or micro-adjust the production stop. Page 14 |
| Blade not cutting through the mat | Pushing down on the handle bar, uneven pressure on the cutting head, debris under the cutting bar, or blade depth too shallow. | Keep steady downward pressure on the blade holder only, clean under the cutting bar with a cloth, brush or compressed air, and increase blade depth. Page 14 |
| Hook in the corner or long curve in the cut | Too much blade depth letting the tip flex, a dull blade, handle bar pressure, a short slip sheet, uneven pressure, or the blade tip adjustment screw needs adjusting. | Correct blade depth, replace the blade, use a full-length slip sheet, and turn the blade tip adjustment screw in slightly without overtightening (page 13). Page 14 |
| Cutting head hard to pull | Dull blade, too much bevel blade depth, slip sheet left in for straight cuts, or cutting head tension screws need adjusting. | Replace the blade, reduce depth, remove the slip sheet for straight cuts, and check the bushing and bearing setscrews (page 12). Page 14 |
| Borders uneven from one end to the other | Mat and slip sheet not tight against the mat guide, mat guide not parallel, or mat board not squared. | Push the mat firmly against the guide and re-parallel the mat guide with screws A and B (page 13). Page 14 |
| Cuts not square when downsizing mat board | Mat not held squarely against the squaring bar, or the squaring arm is out of square. | Check with an L-shaped carpenter's square and adjust the strut bracket to re-square the arm (page 11). Page 14 |
| Cutting head loose on the rail | Cutting head tension screws need adjustment. | Slightly tighten the front and rear bushing screws and the roller bearing screw until light resistance is felt; do not overtighten (page 12). Page 14 |
Frequently asked questions
What blade does the Platinum Edge use?
Logan Blade Model 267, a 0.012" thick double bevel blade. Any 3/4" tall blade can be used if blade depth and production stops are adjusted to suit (page 5).
Can it cut 8-ply mat board?
Yes. It cuts 4- and 8-ply board. For 8-ply, increase blade depth and make a line-to-line test cut on one corner, starting and stopping about 3/8" past the lines, without the production stops (page 7).
How do I know when to change the blade?
Ragged cuts or a blade that tears instead of slicing the mat mean it is dull. Replace it, or reverse a double bevel blade to use the unused side (page 5).
What tools come in the box?
Four Allen wrenches (1/8", 5/32", 5/64" and 1/16"), the handle bar lift knob and screw, and two 5-count replacement blade packs (page 4).
What is the warranty?
Logan warrants Models 850, 855 and 860 against defects in parts and workmanship for two years from the date of original purchase (page 15).
