

Page 1 of 10

Text on page 2
Model 3010 Letter Opener
Operators Manual
post mark
3485 Sacramento Dr. Ste. E San Luis Obispo, CA 93401, USA Phone (805) 594-1454
Enighedsvej 21 5000 Odense C Phone +45 65 910
Fax +45 65 910 E-mail: postmark@mail-is-
Page 2 of 10

Text on page 3
Model 3010 Letter Opener Operating Instructions
Please read these operating instructions to ensure that your letter opener is used effectively and safely!
If after reading this manual you have unanswered questions or issues regarding your letter opener, please contact your local letter opener dealer.
It is recommended that you save the box and packaging in which your machine arrived. If the machine ever needs to be shipped for maintenance, the correct sized box and packaging will protect it during shipping.
Please Note: Because of Electrical Hazard and possible damage to the machine, the cabinet on your letter opener should only be opened by a trained technician
Page 3 of 10

Text on page 4
General Operating Instructions
Setting Up Your Letter Opener
The 3010 letter opener should be placed at a height that is comfortable for the operator. An adjustable table or chair is useful in positioning the letter opener.
If you need to extend the length of the hopper, you can flip up the feed extender as shown in the picture.
Preparing the Mail for Opening
If mail is not properly prepared, the edge of the contents may be cut along with the envelope. You may open several different sizes of mail simultaneously. For best results, please take care to prepare mail as follows:
Remove any foreign objects such as: o Paper Clips o Rubber Bands o Staples
Foreign objects will damage the Cutting Blade or Feed Belts and may void your warranty.
away for the line of cut. This is to prevent unwanted cutting of contents.
Page 4 of 10

Text on page 5
Start/Stop
Plug the cord first into the Power Supply Socket, then into wall outlet.
Turn the letter opener to the ON position (“1”). The mail will now begin feeding.
ON/OFF
Switch
Power Supply Socket
Keep fingers, jewelry and long hair away from the feed belts while operating the machine. When not in use, make sure to turn the letter opener to the OFF position
Operating Your Letter Opener
On the top of the letter opener, there are lights that can help you in running your letter opener.
Back Guide Plate
- Place mail on hopper so that all pieces are flush against the Back Guide Plate.
- Make sure leading edge of the mail is resting on the Feed Belts, and the mail is covering the sensor.
- If the sensor is not covered, the machine will not run.
Your letter opener should now be ready to accept mail, and is ready for power.
Page 5 of 10

Text on page 6
Large Envelopes
If you are going to run large envelopes through this opener, you will have to flip up the Feeder Extender. It is easier for large envelopes to jam, therefore running less envelopes at one time makes it harder for the letters to jam.
Back Guide Plate
Feeder Belts
Feeder Extender
Upon completion of setup and operation, your Postmark Model 3010 Letter Opener should look similar to the above. A properly set up and maintained Postmark Model 3010 Letter Opener can open around 18,000 envelopes per hour. See Troubleshooting / Machine Maintenance for more details.
Page 6 of 10

Text on page 7
Troubleshooting / Machine Maintenance
Machine Won’t Start
If after switching the power on your Model 3010 does not appear to be operating, there are a few things to check. The first item to check would be the lights at the top of the machine. Knowing what each of these lights mean, helps you diagnose why your letter opener isn’t running properly
What to check:
- No light
- Track Cover
- Fuse
- Green Light
- Sensor
- Solid Red
- Drive Belts
- Blinking Red
- Envelope Jam
Checking the color of the lights on top of the machine is the best way to determine why exactly your letter opener is not running properly.
Track Cover
- First, switch the power to the OFF position and clear away any mail from the opener.
- Check to make sure the Track Cover is seated all the way down. The Model 3010 is equipped with a safety switch to ensure that the machine will not operate if the cover is off, or loose.
- Switch the power to the ON position.
Page 7 of 10

Text on page 8
Troubleshooting / Machine Maintenance (continued)
Fuse
The Model 3010 Letter Openers are protected by a 3 Amp, 250 Volt fuse. The machine will not operate if the fuse is blown or missing. To check the fuse:
- Switch the power to the OFF position and clear any mail from the opener.
- Remove the Power Cord from the Power Supply Socket.
- Pull out on the tray located just to the left of the Power supply Socket.
- Remove the fuse for Fuse inspection. There should be a single thin piece of metal that runs along the center of the fuse. If the metal strip is burnt out or broken anywhere inside, replace the fuse.
- Slide tray back into Power Supply Socket and reattach the Power Cord.
- Switch the Power to the ON position.
Sensor
Check the sensor to make sure it is being covered by the envelopes. If the sensor is not being covered by mail, the light on the top of the machine will be green. Once the machine senses the envelopes, the light should turn solid red. If there are letters covering the sensor and the light is still green, you will need to contact your local dealer for authorized service.
Drive Belt
If you can hear the motor running inside your Letter Opener but the Feed Belts are not moving, it is likely that the Drive Belt is broken or off. You will need to contact your local dealer for authorized service.
Page 8 of 10

Text on page 9
Troubleshooting / Machine Maintenance (continued)
Cleaning the Feed Belts
During normal use, your letter opener will accumulate dirt and dust along the Feed Belts. To maintain maximum efficiency and ensure correct operation it is recommended that the belts be cleaned regularly.
Clearing an Envelope Jam
If an envelope should become jammed in the machine, follow these simple steps for removal:
- Turn the machine off and disconnect the power supply.
- Remove the blue track cover. (lift up and pull out)
- Pull the jammed envelope through the track in the direction of exit.
- Replace the track cover securely.
- Re-connect the power cord.
Envelope jams usually occur when the machine is running fast, or large envelopes are being run through. If envelope jams seem to occur too frequently, turning down the speed would decrease your risk of a jam. You should also separate any large envelopes and run those separately. The faster an envelope travels, the more likely it is to jam. Turning down the speed will insure a consistent cut.
NOTE: The track cover is connected to a safety switch. The letter opener will not run unless the cover is securely replaced.
Irregular or Partial Opening
A few things can lead to your mail being improperly opened. Most commonly, this is due to improper feeding, and unclean Feed Belts.
In the unlikely event that your mail is still not being properly opened, it is possible that the cutting knife is out of adjustment or has been damaged. You will need to contact your local dealer for authorized service.
Any and All Other Repairs
Should your machine require additional repair, please contact your local dealer. All repairs are to be made by a trained technician only.
Page 9 of 10

Text on page 10
The Letter Opener should only be opened by a trained technician
Product Information
Maximum Speed: Maximum Envelope Thickness: Dimensions (H/W/D): Shipping Dimensions (H/W/D): Net Weight of Opener: Shipping Weight: Power Supply:
PRODUCT:
MAKE/MODEL: DESCRIPTION:
18,000 envelopes per hour 3/16” / 4 mm 7”x13”x9” / 180x330x215mm
10 lbs. / 4.4 kg 115V - 60 Hz / 220V-50 Hz
Letter Opener Model 3010 Electrically Driven Letter Opener
Page 10 of 10 ยท End of manual
Quick start
- Place the opener at a comfortable working height; flip up the feed extender if you need a longer hopper.
- Remove paper clips, rubber bands and staples from the mail, and tap contents away from the cutting edge.
- Plug the cord into the power supply socket first, then into the wall outlet.
- Stack mail flush against the back guide plate with the leading edge resting on the feed belts and covering the sensor.
- Turn the switch to ON ("1"); mail begins feeding.
- For large envelopes, flip up the feeder extender and run fewer envelopes at a time.
- Turn the opener OFF when not in use.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine won't start, no light | Track cover not seated (safety switch) or blown/missing 3 A, 250 V fuse. | Switch off, seat the track cover fully, and check the fuse in the tray beside the power socket; replace it if the metal strip is broken (page 8). Page 7 |
| Green light but machine won't run | Sensor is not covered by mail. | Make sure the leading edge of the mail covers the sensor. If mail covers it and the light stays green, contact your dealer. Page 8 |
| Motor runs but feed belts don't move | Drive belt is broken or off. | Contact your local dealer for authorized service. Page 8 |
| Envelope jam (blinking red light) | Running too fast or feeding large envelopes. | Turn off and unplug, lift and pull out the blue track cover, pull the envelope through in the exit direction, and replace the cover securely. Lower the speed or run large envelopes separately. Page 9 |
| Irregular or partial opening | Improper feeding or dirty feed belts; less often a knife out of adjustment or damaged. | Prepare and feed mail correctly and clean the feed belts. If it continues, contact your dealer. Page 9 |
Frequently asked questions
How fast is the PostMark 3010?
Up to 18,000 envelopes per hour when properly set up and maintained (page 6).
How thick an envelope can it open?
Maximum envelope thickness is 3/16" (4 mm) (page 10).
What fuse does the 3010 use?
A 3 Amp, 250 Volt fuse, located in the tray just left of the power supply socket (page 8).
Can I open different envelope sizes together?
Yes, several sizes can be opened at once, but large envelopes jam more easily, so run them in smaller batches with the feeder extender up (page 4).
