

Page 1 of 18

Text on page 2
Model 3030 Letter Opener Rotary
Issued July 1, 2003
3197 Duncan Lane Suite A San Luis Obispo, CA Corporate (805)594-1454 FAX (805) 594-1455 EMAIL: postmark@postmark-usa.com WEBSITE: postmark-usa.com
Page 2 of 18

Text on page 3
All rights reserved. No part of this document may be reproduced or transmitted in any form without written permission by POSTMARK Inc.
Page 3 of 18

Text on page 4
TABLE OF CONTENTS
- IDENTIFICATION AND ELECTRICAL RATING PLATE
- TECNICAL DESCRIPTIONS AND SPECIFICATIONS
2.1 DESCRIPTION
2.2 SPECIFICATIONS
- SAFETY
- INSTALLATION
4.1 UNPACKING AND
CHECK LIST 4.2 SETTING UP
- OPERATIONS
WARNING:
THE ROTARY OPENER 3030 HAS BEEN DESIGNED AND
MANUFACTURED TO OPERATE AS INDICATED IN THIS MANUAL. THESE MACHINES MUST BE USED ONLY TO OPEN DOCUMENTS AS INDICATED IN PARAGRAPH 2.1. THE MANUFACTURER IS NOT RESPONSIBLE IF THE MACHINE IS USED INCORRECTLY.
READ THIS MANUAL CAREFULLY, OBSERVING ALL RECOMMENDED SAFETY PRECAUTIONS BEFORE INSTALLING AND USING THE MACHINE.
Page 4 of 18

Text on page 5
- IDENTIFICATION AND ELECTRICAL RATING PLATE.
Attached on the rear side is the plate with identification and electrical rating data.
The plate indicates:
the model, the code (P/N) and the serial number (S/N) of the machine. the year of production the operating voltage, the frequency, the ampere and the fuses rate.
Please refer to the model, code (P/N) and serial number (S/N) of the machine when ordering spare parts or repairs.
Make sure the indicated voltage is in use in your country. Should the indicated voltage be different from that in use in your country, contact you authorized service agent.
Page 5 of 18

Text on page 6
- TECHNICAL DESCRIPTIONS AND SPECIFICATIONS
2.1 DESCRIPTION
The 3030 Rotary letter opener is designed to open envelopes of all kinds especially thick, reinforced, gusseted, stapled, plasticized, damaged, uneven and very large envelopes. It is not recommended for envelopes made of plastic. The envelope is introduced momentarily to the blade which cuts off approx. 3/10 of a millimeter. Do not introduce in the unit any other kind of things other than envelopes. Thin envelopes may be introduced in multiples. Envelopes may be opened on 3 sides.
- OILING LEVERS
- ON / OFF PUSH BUTTON
- FUSES
- CUTTING APERTURE
- WASTE DRAWER
- BICOLOR LED
Page 6 of 18

Text on page 7
2.2 SPECIFICATIONS
2.2.5 HOMOLOGATIONS AND
MARKS
2.2.1 ELECTRICAL AND
ENVIROMENTAL SPECIFICATIONS
Operative Temperature Storage Temperature Operative Humidity Storage Humidity
230V 50Hz (-10% +10%) 115V 60Hz (-10% +6%) 100V, 50/60 Hz (-10% +6%)
2.2.2 ENVELOPES SPECIFICATIONS
Width Thickness
The unit is certified by IMQ according to the following rules:
EN 60950 Safety EN 50081-1 Electromagnetic compatibility EN 50082-1 Electromagnetic compatibility
MARKS
ENEC 03 (European Norms Electrical Certification) EMC International CE
Up to 14 in Up to 0.25 in
2.2.3 DIMENSIONS AND WEIGHT
width: 17.75 in depth: 9 in height: 5.35 in 27 lbs
2.2.4 SHIPPING DIMENSIONS AND
WEIGHT
width: 22.80 in depth: 13.75 in height: 10.62 in
NOTE: The Postmark policy is one of continuous improvement to their product and as such they reserve the right to change product specifications without prior notice.
Page 7 of 18

Text on page 8
- SAFETY
The machine has been designed, manufactures and equipped so as to prevent any risk to the operator. However, the operator must observe the following instructions when operating the equipment
DO NOT APPROACH THE ROTATING
PARTS OF THE MACHINE WITH LOOSE JEWELLERY
DO NOT APPROACH THE ROTATING
PARTS OF THE MACHINE WITH THE FREE LONG HAIR
Page 8 of 18

Text on page 9
DO NOT PUT ANY OBJECT ON THE
MACHINE.
DO NOT PUT OBJECTS CONTAINING WATER OR OTHER LIQUIDS NEAR THE MACHINE.
DO NOT USE WATER TO CLEAN
THE MACHINE.
DO NOT INSTALL THE MACHINE
NEAR HEAT SOURCES.
Page 9 of 18

Text on page 10
UNPLUG THE MACHINE BEFORE
ANY CLEANING OPERATION OR BEFORE REMOVAL OF JAMMED PAPER.
DO NOT TOUCH THE BLADES.
IF YOU REMOVE THE WASTE
DRAWER, DO NOT TOUCH THE BLADES.
IF YOU REMOVE THE WASTE
DRAWER, DO NOT INSERT ANYTHING ON THE SLOT OF THE MICRO SAFETY SWITCH. DO NOT TRY TO TOUCH OR REMOVE THE MICRO SAFETY SWITCH
WARNING: INTERNAL OPERATION
OR REPAIR MUST BE DONE ONLY BY SPECIALIZED PERSONNEL
Page 10 of 18

Text on page 11
- INSTALLATION
4.1 UNPACKING AND CHECK LIST
The Shipping Package Contains:
3030 Rotary Power Cord Operator Manual
If you see any sign of damage immediately notify the shipping company or your dealer. Save the packing and also shipping documents. Saving the packing will make moving the unit easier in the future.
Page 11 of 18

Text on page 12
4.2 SETTING UP
BEFORE CONNECTING POWER
CORD TO THE ELECTRICAL SUPPLY, CHECK THAT THE RATING PLATE CORRESPONDS TO YOUR LOCAL VOLTAGE. CONNECT THE POWER CORD TO THE MACHINE, PUSHING THE PLUG SECURELY INTO THE SOCKET
CONNECT THE PLUG OF THE
POWER CORD TO THE WALL SOCKET. THE MACHINE IS NOW READY TO OPERATE
WARNING: THE PLUG OF THE
POWER CORD IS CONSIDERED AS ELECTRICAL DIVIDING UNIT. THE RELATIVE WALL SOCKET MUST BE PLACED NEAR THE MACHINE AND EASILY ACCESIBLE. THE ELECTRICAL NET MUST BE GROUND CONNECTED
Page 12 of 18

Text on page 13
- OPERATIONS
CONTROLS:
ON/OFF PUSH BUTTON
OILING LEVERS BICOLOUR LED
TO OPEN ENVELOPES, SWITCH ON THE MACHINE BY PRESSING THE ON/OFF PUSH BUTTON. THE BICOLOR LED LIGHTS GREEN (INSTEAD OF RED). INTRODUCE THE ENVELOPE INTO CUTTING APERTURE AND PRESS FOR AN INSTANT AGAINST THE ROTARY BLADE. REPEAT ON OTHER TWO SIDES FOR COMPLETE OPENING AND VERIFICATION. WHEN YOU HAVE FINISHED OPERATIONS WITH THE MACHINE, SWITCH OFF THE MACHINE BY PRESSING THE ON/OFF PUSH BUTTON.
NOTE: THE BICOLOR LED WILL
BLINK RED FOR ABOUT 4 sec. DURING THIS PERIOD DO NOT TRY TO OPEN THE WASTE DRAWER BECAUSE THIS IS BLOCKED. ONLY WHEN THE BICOLOR LED WILL BECOME FIXED RED IT WILL BE POSSIBLE TO OPEN THE WASTE DRAWER.
Page 13 of 18

Text on page 14
TO PREVENT SQUEAKING OF
ROTARY BLADE, MOVE OILING LEVERS TOWARDS YOU AND HOLD WHILE 3030 ROTARY IS RUNNING FOR 1-2 SECONDS.
NOTE: IF DURING THE FUNCTIONING THE MACHINE STOPS THE POSSIBLE CAUSE ARE THE FOLLOWING:
1- BICOLOR LED SWITCHED OFF
- LACK OF POWER SUPPLY
- BROKEN FUSES
2 - BICOLOR LED BLINKS RED AND
AFTER ABOUT 4 sec BECOMES FIXED RED
- TEMPORARY LACK OF POWER SUPPLY
- THE WASTE DRAWER IS NOT IN THE CORRECT POSITION AND DOES NOT TOUCH THE SAFETY MICROSWITCH
3 - BICOLOR LED IS GREEN
- MECHANICAL ITEMS BROKEN
- JAMMED ENVELOPES BECAUSE OF THE THICKNESS
- MOTOR INTERNAL PROTECTION DUE TO EXCESS OF HEAT
WARNING: IN LAST CASE ONCE
THE MOTOR HAS COOLED THE UNIT WILL RESTART WITHOUT ANY NOTICE. IN THIS CASE UNPLUG THE UNIT OR PRESS THE BUTTON ON- OFF.
Page 14 of 18

Text on page 15
ACTIONS
POINT 1:
CHECK AND IF NECESSARY SUBSTITUTE. IF THE UNIT STILL DOES NOT WORK, UNPLUG THE MACHINE AND CONTACT YOUR LOCAL AUTHORIZED SERVICE AGENT.
POINT 2:
CHECK AND SWITCH ON THE MACHINE. IF THE MACHINE STILL DOES NOT WORK, UNPLUG THE UNIT AND CONTACT YOUR LOCAL AUTHORIZED SERVICE AGENT
POINT 3:
SWITCH OFF THE MACHINE AND WAIT FOR A WHILE UNTIL THE
TEMPERATURE COOLS DOWN. SWITCH ON THE MACHINE. IF THE MACHINE STILL DOES NOT WORK, UNPLUG THE UNIT AND CONTACT YOUR LOCAL AUTHORIZED SERVICE AGENT.
Page 15 of 18

Text on page 16
THE ROLLER IS ALREADY SATURATED WITH OIL BY THE DEALER. IT SHOULD THEREFORE BE NECESSARY TO APPLY A LITTLE DROP OF OIL ALONG THE SPECIAL SLOT TO REPLENISH THE OIL SUPPLY AT MONTHLY INTERVALS.
REMOVE WASTE DRAWER AND
EMPTY REGULARY. PUSH FULLY HOME WHEN EMPTIED TO CONNECT SAFETY SWITCH AND ALLOW MACHINE TO OPERATE. THIS OPERATION MUST BE DONE ONLY IF THE MACHINE IS SWITCHED OFF AND THE BICOLOR LED LIGHTS FIXED RED.
WARNING: THE MACHINE DOES
NOT WORK WITHOUT THE WASTE DRAWER IN THE CORRECT POSITION.
Page 16 of 18

Text on page 17
TO CHANGE THE FUSES, UNPLUG
THE MACHINE, REMOVE THE SMALL COVERS, TAKE AWAY THE OLD FUSES, FIT THE NEW FUSES AND REPOSITION THE COVERS.
WARNING: FUSE REPLACEMENT. REPLACE THE FUSE USING A FUSE OF THE SAME TYPE AND VALUE AS INDICATED ON THE PLATE ON THE REAR OF THE MACHINE. IF THE FUSE BLOWS OUT AGAIN, UNPLUG THE MACHINE AND CONTACT YOUR LOCAL AUTHORIZED SERVICE AGENT.
WARNING: IF DURING THE FUNCTIONING THE ELECTRICITY DROPS OR THE PLUG IS ACCEDENTALY DISCONNECTED, THE UNIT WILL BE IN POSITION OFF (LED BICOLOR RED) WHEN THE ELECTRICITY WILL RETURN OR THE PLUG CONNECTED AGAIN. TO START THE UNIT PRESS PUSH BUTTON ON/OFF.
Page 17 of 18

Text on page 18
AVOID SQUEAKING OF ROTARY BLADE BY OILING IT REGULARLY
TURN OFF THE UNIT WHEN NOT USED TO AVOID UNNECESSARY USE
OF ROTARY BLADE
DO NOT PROCESS ENVELOPES WITH STAPLES
INSERT CAREFULLY THE WASTE DRAWER TO AVOID MECHANICAL OR
ELECTRICAL PROBLEMS
DO NOT TAKE OFF THE WASTE DRAWER UNTIL THE LED TURNS TO
FIXED RED
Page 18 of 18 ยท End of manual
Quick start
- Check that the rating plate on the rear matches your local voltage.
- Connect the power cord to the machine, then plug it into a nearby, grounded wall socket.
- Press the ON/OFF button; the bicolor LED turns from red to green.
- Insert the envelope into the cutting aperture and press it briefly against the rotary blade.
- Repeat on the other two sides for complete opening.
- Press ON/OFF to switch off when finished; wait until the LED is fixed red before removing the waste drawer.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine stops and LED is off | No power supply or broken fuses. | Check power and replace the fuses with the same type and value shown on the rear plate. If it still fails, contact an authorized service agent. Page 14 |
| LED blinks red, then stays fixed red | Temporary loss of power, or the waste drawer is not seated against the safety microswitch. | Check the waste drawer is pushed fully home and switch the machine on again. Page 14 |
| Machine stops while LED is green | Broken mechanical parts, an envelope jammed because of its thickness, or motor thermal protection from overheating. | Switch off and let it cool, then switch on. The motor can restart by itself after cooling, so unplug or switch off first. If it still fails, call service. Page 15 |
| Rotary blade squeaks | Blade needs oil. | While the machine runs, pull the oiling levers toward you for 1–2 seconds, and add a drop of oil to the roller slot monthly. Page 14 |
Frequently asked questions
What envelopes can the 3030 open?
Envelopes up to 14" wide and 0.25" thick, including thick, reinforced, gusseted, damaged and very large ones. It is not recommended for plastic envelopes (page 6, page 7).
How do I oil the 3030 Rotary?
Hold the oiling levers toward you for 1–2 seconds while it runs to stop squeaking, and add a small drop of oil along the roller slot at monthly intervals (page 14, page 16).
Why won't the waste drawer open?
It is locked while the LED blinks red for about 4 seconds after switching off. Remove it only when the LED is fixed red (page 13).
How big is the 3030?
17.75" wide, 9" deep and 5.35" high, weighing 27 lbs (page 7).
