Renz Combi E Electric Plastic Comb Binding Machine Users Manual, page 1

Page 1 of 3

Renz Combi E Electric Plastic Comb Binding Machine Users Manual, page 2
Text on page 2
  1. Störung Bei Störung prüfen:

Hauptschalter an?

Elektrostecker auf beiden Seiten richtig eingesteckt?

Strom auf der Steckdose? Gerätesicherung o.k.? (ggf. austauschen)

  1. Herausnehmen des gebundenen Blocks

Binderücken durch Zurückführen des Bindehebels bis zum Anschlag schließen. Gebundenen Block senkrecht nach oben herausnehmen - fertig. Nachträgliches Auswechseln oder Hinzufügen von Blättern ist möglich. Dabei verfahren Sie genauso, wie beim normalen Stanz- und Bindevorgang.

Abfallschublade gelegentlich entleeren.

Empty waste tray periodically.

11. Vidage Vider le tiroir réguliérement

10. Removing the bound block When all of the sheets have been inserted onto the plastic comb, close it by pushing the binding lever all the way to the back until it stops. Remove the bound document by sliding it up over the vertical comb retaining fingers. To remove or insert pages, check that the binding lever is firmly to the back and then slide the document over the fingers with he spine of the plastic comb on the punching slot side and the book lying towards the front of the machine. Pulling the binding handle towards you will open the binding comb and allow you to remove or insert loose sheets.

10. Enlèvement du bloc relié Fermez la baguette plastique en ramenant le levier de reliure jusqu’à la butée. Enlevez le bloc relié verticalement vers le haut.

Ça y est ! Il est possible d’échanger ou bien d’ajouter des feuilles plus tard. Pour ce faire, procédez de la même manière que lors des opérations de perforation et de reliure normales. Insérez le bloc relié avec la baguette plastique dans le peigne de retenue et poussez-le jusqu’à tout en bas, le levier de reliure étant collé sur la butée arrière. Ouvrez la baguette plastique en tirant le levier de reliure en avant. Ensuite, ôtez les feuilles en question ou bien perforez-les et ajoutez-les tout en procédant comme lors des opérations de perforation normales.

  1. Retirado del bloque encuadernado Cierre el encuadernador plástico reconduciendo la palanca de encuadernado hasta el tope. Retire el bloque encuadernado verticalmente hacia arriba. ¡Ya está!

Es posible sustituir o añadir hojas aún más tarde. A tal efecto, proceda al igual que en las operaciones de troquelado y de encuadernado normales. Pase el bloque encuadernado con el encuadernador plástico por el peine de retención y empújelo enteramente hacia abajo. Para ello, la palanca de encuadernado debe estar adherida al tope trasero. Abra el encuadernador plástico tirando la palanca de encuadernado hacia adelante. Después, quite las hojas en cuestión o bien perfórelas y añádalas. Proceda tal como en la operación de troquelado normal.

Vaciar la bandeja del desperdicio del papel periodicamente

Nur trocken reinigen. Nur mit trockenem Tuch abwischen. Keine Lösungsmittel verwenden, Aufdrucke können sich lösen. Schublade regelmäßig leeren. Schublade an der Vorderseite des Geräts herausziehen und Papierschnitzel ausschütten.

Clean with a dry cloth only. Do not use solvents. Sticker may detach. Empty drawer regularly. Pull out drawer at the back and empty out paper shavings.

Nettoyez uniquement à sec N’essuyez qu’avec un torchon sec. N’utilisez pas de solvants car les inscriptions risquent de se détacher. Videz régulièrement le tiroir Sortez le tiroir à la face de l’appareil pour déverser les découpures de papier.

Sólo limpieza seca Limpie solamente con un trapo seco. No emplee disolventes. Es posible que impresiones se deshagan de la máquina.

Vaciamiento regular del cajón Saque el cajón en la faz del aparato y vacíe los recortes de papel.

Netzstecker ziehen. Sicherungshalter mit Schraubenzieher herausdrücken, (befindet sich an der rechten Seite des Geräts, unter dem Hauptschalter). Sicherung kontrollieren; wenn defekt, neue Sicherung an Stelle der defekten Sicherung einsetzen. Sicherungshalter einsetzen und eindrücken. Netzstecker einstecken; Maschine ist wieder betriebsbereit.

Neue Ersatzsicherung beschaffen.

Gerät nicht öffnen - Gerät darf nur vom Fachpersonal geöffnet werden. Bei Bedarf ins Werk einschicken.

Verificar en caso de desarreglo: ¿Interruptor principal conectado? ¿Clavijas eléctricas correctamente enchufadas en ambos lados? ¿Tomacorriente bajo corriente? ¿Fusible protector del aparato en orden? (reemplazarlo si fuera necesario)

  • Retirar la clavija de conexión a la red.

Quitar el portafusible exprimándolo mediante un destornillador, (se encuentra en el lado derecho del aparato, por debajo del interruptor principal). Controlar el fusible; si es defectuoso, reemplazarlo por otro fusible. Instalar de nuevo el portafusible y apretarlo adentro. Enchufar la clavija de conexión a la red; la máquina vuelve a estar lista para el servicio.

No abrir el aparato - sólo el personal especializado es autorizado para abrir elaparato. En el caso necesario, remitirlo a la fábrica.

Check in case of malfunctio Main switch turned on? Electrical plug is connected correctly? Electricity from plug? Fuse o.k.? Exchange if necessary! Take out main plug. queeze out fuse holder with screw driver (at the right side of the machine, below the main switch). Check fuse - if fuse is defective put in replacement fuse. Put in fuse holder and press it in. connect main plug. Machine is ready for operation again.Get a new replacement fuse. Do not open the machine! Machine is only to be opened by trained service technicians. If necessary return to RENZ.

Contrôles à effectuer en cas de dérangement : Interrupteur principal enclenché ? Fiches électriques correctement branchées aux deux côtés ? Prise électrique sous tension ? Fusible miniature en ordre ? (le remplacer le cas échéant) Retirer la fiche de secteur. Sortir le porte-fusible en le pressant par l’intermédiaire d’un tournevis (se trouve sur le côté droit de l’appareil, au-dessous de l’interrupteur principal). Contrôler le fusible ; si défectueux, insérer un fusible neuf à la place du fusible défectueux. Remettre le portefusible en place et l’enfoncer. Ficher la fiche de secteur ; machine est de nouveau en ordre de marche. Se procurer d’autres fusibles de rechange.

Ne pas ouvrir l’appareil - seul de la main-d’œuvre experte est autorisée à ouvrir l’appareil. Le renvoyer à l’usine en cas de besoin.

Nennspannung 240 V Motor250 W 2,9 A Gewicht 38 kg Frequen 50 Hz Lüfter 14 W 0,8 A

Garantie: Auf dieses Gerät gewähren wir, bei pfleglicher Behandlung, eine Garantie von einem Jahr.

Stand: 11 / 02

Bedienungsanleitung

Papieranschlag DIN A 5 Paper guide A 5 ( 8,5“ ) Butée A 5 Tope de papel A 5

As per 11 / 02

  1. Caractéristiques techniques

Tension nominale 240 V Moteur 250 W 2,9 A Poids 38 kg Fréquence 50 Hz Ventilateur 14 W 0,8 A

Garantie : Nous accordons une garantie d’une année pour cet appareil pourvu qu’il soit manipulé avec soin.

A la date du : 11 / 02

Tensión nominal 230 V 50 Hz ( o 110 V 60 Hz ) Motor 250 W 2,9 A Peso 38 kg Ventilador 14 W 0,8 A

Garantía: Para este aparato asumimos la garantía durante un año siempre que se lo trate con cuidado.

Fecha 11 / 02

Instrucciónes de servicio

Typ / Typ / Type / Tipo 33 + 34

Druckstücke Pins Presseur Piezas de presión

Papieranschlag DIN A 4 Paper guide A 4 ( 11“ ) Butée du papier A 4 Tope de papel A 4

Perforationsschacht Punching shaft Arbre de base Canal de perforación

Lüftungsgitter Air slots Grilles d´aération Respiradores de ventilación

Haltekamm Comb holder Peigne de retenue Peine de retención

Aufziehhaken Opening hooks Crochets d´ecartement Ganchos de expansión

Drehknopf Stanztiefenverstellung Adjusting scale edge adjustment Alignement échelle graduée Ajuste de profundidad de perforación

Maßskala Scale Échelle de mesure Escala de diámetros

Abfallschublade Waste tray Tiroir á rognures Cajón de desperdicios

Rändelschraube Knurled screw Vis moletée Tornillo moleteado

Netzanschluß mit Sicherung Voltage and fuse Branchement au réseau fusible Bindehebel Conexión a la red fusible Binding lever Levier de reliure Palanca de encuadernación

1. Aufstellen u. Anschließen

1. Setup and Connection

1. Mise en place et connexion électrique

1. Emplazamiento y conexión

Remove inner packing. Check to be certain that you have re ceived the following items

Enlevez les cartons de protection, vérifiez le volume de livraison

Deshaga las cajas de cartón protector, verifique el volumen de suministro

Warranty: 12 months with careful operation.

Instructions de service

Blockdicken - Skala Measuring scale Echelle de mesure Escala de grueso de bloque

Nominal voltage 240 V ( 115 V Motor 250 W 2,9 A Weight 38 kg ( 83,6 lbs. ) Nominal curren 50 Hz ( 60 Hz ) Fan 14 W 0,8 A

Manual

RENZ combi-E

Combi-Gerät Fußschalter mit Kabel Elektroanschlußkabel Bedienungsanleitung

Combi machine Foot pedal Power cord Operation manual

Gerät aus dem Karton heben (nicht am Bindehebel hochheben) Gewicht: 38 kg, deshalb mit 2 Personen am Maschinenboden anfassen und herausheben.

Lift the machine by the sides to remove from the box. Do not lift at the binding lever or under the front of the waste tray. Weight: 38 kg / 84 lbs. It is recommended that the machine is lifted by 2 people.

Stabilen Standort wählen. Der Standort muß voll abgestützt sein. Vorstehende Arbeitsplatten sind ungeeignet.

Vorsicht: Bei starkem Temperaturwechsel erst nach 2 Stunden einschalten. Wenn das Gerät aus einem kalten Raum kommt, kann sich Kondenswasser gebildet haben.

Stecker der Gerätezuleitung in die Buchse an der rechten Seite einstecken und Stecker an Steckdose anschließen (240 V). Hauptschalter an der linken Seite des Geräts einschalten. Fußschalter drücken - Motor läuft und stanzt.

Achtung: Motor läuft nur, wenn Pedal gedrückt wird und stoppt dann wieder.

Select a solid work surface Work surface must be completely supported. Unsupported table extensions are notsuitable.

Caution: In case of major change of temperature turn on the machine only after 2 hours.If the machine has been in a cold room, water condensation may be possible.

Plug the main power plug into the socket at the back of the machine, then insert the plug into the wall outlet. (115 V) (240 V).

Turn on the main switch at the right side of the machine. Fan will start running. Press foot pedal motor runs and cycles the punch.

Note: Motor runs only if pedal is pressed and will stop immediately after releasing.

appareil Combi-E interrupteur à pédale avec câble câble d’alimentation électrique notice d’utilisation

Sortez l’appareil du carton (ne le soulevez pas par le levier de reliure) poids: 38 kg, pour cela il faut 2 personnes qui le saisissent au fond pour le soulever et le sortir du carton.

Choisissez un emplacement solide Il faut que l’emplacement soit entièrement appuyé. Des plateaux de travail saillants sont impropres.

Attention ! Au cas où la variation de température serait importante, ne mettez la machine en marche qu’après 2 heures, si l’appareil vient d’une salle froide, il pourrait y avoir de l’eau condensée.

Fichez la fiche de l’interrupteur à pédale dans la douille située sur la paroi latérale droite et posez l’interrupteur à pédale par terre. Fichez la fiche du cordon d’alimentation dans la douille située sur le côté droit ; ensuite, branchez la fiche sur la prise de courant (240 V). Enclenchez l’interrupteur principal situé sur le côté gauche de l’appareil. Appuyez sur l’interrupteur à pédale - le moteur marche et perfore.

Attention ! Le moteur ne marche que tant que la pédale sera actionnée, puis il s’arrêtera de nouveau.

aparato Combi-E interruptor de pie con cable cable de conexión eléctrica manual de instrucciones

Quite el aparato del cartón (no lo levante por la palanca de encuadernado)

peso: 38 kg, por tanto hace falta 2 personas quienes cogen el aparato por el fondo para sacarlo.

Elija un emplazamiento sólido La ubicación del aparato tiene que estar enteramente apoyada. Tableros salientes son impropios . ¡Atención! En caso de que el cambio de temperatura sea importante, espere 2 horas antes de poner la máquina en marcha; si el aparato viene de una sala fría, es posible que haya agua condensada.

Enchufe la clavija del interruptor de pie en la hembrilla que está en la pared lateral derecha y ponga el interruptor de pie al suelo. Enchufe la clavija del conductor flexible de conexión del aparato en la hembrilla que está en el lado derecho; entonces enchufe la clavija al tomacorriente. Conecte el interruptor principal que se encuentra en el lado izquierdo del aparato. Apriete el interruptor de pie - el motor arranca y troquela.

¡Atención! El motor marcha solamente mientras se apriete el pedal, de lo contrario el motor se para.

Page 2 of 3

Renz Combi E Electric Plastic Comb Binding Machine Users Manual, page 3
Text on page 3
  1. Das Gerät Einsatzgebiet:

Papier stanzen max. 25 Seiten 70 - 80 g/qm

Karton stanzen max. 1,5 mm

Kunststoff-Folien stanzen max. 2 Seiten à 0,3 mm

max. Bindedicke 50 mm ca. 500 Blatt 70 - 80 g/qm

Keine anderen Materialien oder Metalle stanzen!

Vor dem ersten Einsatz einige Probestanzungen durchführen, damit wird der Rostschutz von den Stanzstempeln entfernt. So oft wiederholen, bis Stanzlöcher keine Fleckenmehr aufweisen.

  1. The machine Operating Range Punching of paper, max. 25 pages 70-80 g/m²

Punching of covers or card stock max. 1,5 mm

Punching of plastic sheets

max. 2 pages à 0,3 mm

Max. binding thickness approx. 500 pages 70-80 g/m²

Don´t punch other material or metal!

Before binding the first time: Punchscrap paper to remove the rust preventative coating from the punch pins. Repeat the process until the holes punch cleanly.

  1. Réglage du format

Am Plexiglas-Anschlag befinden sich die Seitenanschläge für DIN A 4 und DIN A 5. Diese entsprechend anschrauben.

Type 33 pas EUROP, DIN A 4 24 anneaux arrêtez la butée de papier à l’épaulement droitlevez le 4 e membre de pression depuis la gauche DIN A 5 17 anneaux arrêtez la butée de papier à l’épaulement gauchelevez le 4 e membre de pression depuis la gauchelevez le 7 e membre de pression depuis la droite

To adjust for formats A4 and A5 ( 11“ and 8,5“ ) put the paper guide on the side of the plexiglas indicated on the right.

Les butées latérales pour les formats DIN A 4 et DIN A 5 se trouvent sur la butée plexiglas. Fixez-les avec des vis selon le format souhaité.

  1. Ajuste del formato

Los topes laterales para los formatos DIN A 4 y DIN A 5 se encuentran en el tope de plexiglass. Atorníllelos según el formato deseado.

  1. L’appareil Domaines d’application : perforation de papier

max. 25 pages à 70 - 80 g/m²

perforation de carton max.1,5 mm perforation de feuilles en matière plastique max. 2 pages à 0,3 mm

épaisseur de reliure max. 50 mm env. 500 feuilles à 70 - 80 g/m²

ne perforez pas d’autres matéri-aux,ni des métaux non plus

Avant sa première utilisation, effectuez quelques perforations d’essai. Ainsi, vous éliminerez l’antirouille des poinçons de perforation. Répétez les perforations d’essai jusqu’à ce que les trous de perforation ne présentent plus de tache.

  1. El aparato Campos de aplicación: troquelado de papel

Typ 33 EUROP-Teilung, DIN A 4 24 Ringe Papieranschlag am rechten Absatz anschlagen.

  1. Druckstück von links ziehen

DIN A 5 17 Ringe Papieranschlag am linken Absatz anschlagen.

4. Druckstück von links ziehen

7. Druckstück von rechts ziehen

Typ 34 US-Teilung, DIN A 4 21 Ringe Papieranschlag rechts anbringen

  1. Druckstück von links ziehen

DIN A 5 14 Ringe Papieranschlag links anbringen

  1. Druckstück von links ziehen

máx. 25 páginas de 70 - 80 g/m²

troquelado de cartón máx. 1,5 mm

troquelado de hojas de plástico máx. 1 página de 0,3 mm

espesor de encuadernación máx. 50 mm aprox. 500 hojas de 70 - 80 g/m²

¡no troquele otros materiales ni metales!

Efectúe algunos troquelados de ensayo antes de utilizarlo por primera vez. Así se elimina el agente antioxidante de los punzones. Repítalos hasta que las perforaciones ya no presenten manchas.

  1. Adjusting the format

Type 33 EUROP pitch, DIN A4 24 loops put paper guide to the right, pull 4th pin from left

DIN A5 17 loops put paper guide to the left, pull 4th pin from left, pull 7th pin from right Type 34 US pitch, DIN A4 21 loops put paper guide to the right, pull 3rd pin from the left

DIN A5 14 loops put paper guide to the left, pull 3rd pin from left

Type 34 pas USA, DIN A 4 21 anneaux arrêtez la butée de papier à l’épaulement droitlevez le 3 e membre de pression depuis la gauche DIN A 5 14 anneaux arrêtez la butée de papier à l’épaulement gauchelevez le 3 e membre de pression depuis la gauche

  1. Ajuste del formato

Los topes laterales para los formatos DIN A 4 y DIN A 5 se encuentran en el tope de plexiglass. Atorníllelos según el formato deseado. Tipo 33 paso EUROP, DIN A 4 24 anillas detenga el tope de papel en el escalón derecho alce la 4 a pieza de presión desde la izquierda DIN A 5 17 anillas detenga el tope de papel en el escalón izquierdo alce la 4 a pieza de presión desde la izquierda alce la 7 a pieza de presión desde la derecha

Tipo 34 paso EE.UU., DIN A 4 21 anillas detenga el tope de papel en el escalón derecho alce la 3 a pieza de presión desde la izquierda

DIN A 5 14 anillas detenga el tope de papel en el escalón izquierdo alce la 3 a pieza de presión desde la izquierda

  1. Auswahl des Plastikbinderücken- Durchmessers

Mit der am Plexiglas-Anschlag angebrachten Maßtabelle läßt sich der richtige Plastikbinderücken- Durchmesser leicht ermitteln. Den zu bindenden Block waagrecht in den Anschlag der Maßtabelle legen. Der benötigte Plastikbinderücken-Durchmesser läßt sich jetzt rechts an der Skala ablesen.

  1. Determine the binding diameter

Put the edge of the book against the measuring scale on the plexiglas. Read the diameter of the binding element.

  1. Sélection du diamètre du dos de reliure à baguettes plastiques

L’échelle de mesure placée sur la butée plexiglas permet de determiner sans problème le bon diamètre des baguettes plastiques. Placez le bloc à relier horizontalement dans la butée de l’échelle de mesure. Ainsi , vous pouvez relever le diamètre requis de la baguette plastique sur l’échelle à droite.

  1. Selección del diámetro del lomo encuadernador plástico

Es fácil determinar el buen diámetro del encuadernador plástico gracias a la escala de medida que se encuentra en la faz de la máquina. Coloque el bloque a encuadernar horizontalmente en el tope de la escala de medida. Entonces se puede leer el diámetro preciso del encuadernador plástico en la escala a la derecha.

  1. Einstellung des Randabstands

Mit seitlich angebrachtem Drehknopf den Randabstand der Perforation auf den jeweiligen Binderücken Durchmesser einstellen. Die entsprechenden Einstellwerte sind unter dem Drehknopf am Gehäuse angebracht.

  1. Adjust edge distance to selected diameter

Turn adjusting knob to the selected diameter. The index is located below the knob on the housing of the machine.

  1. Réglage de la distance à bord

Réglez la distance à bord de la perforation sur le diamètre de la baguette plastique employée en tournant le bouton placé sur le côté. Les valeurs de réglage correspondantes sont marquées sur la boîte, au-dessous du bouton tournant.

  1. Ajuste de la distancia al margen

Adapte la distancia al margen de la perforación al diámetro del lomo encuadernador utilizado girando el botón giratorio colocado lateralmente. Los valores de consigna correspondientes están puestos en la carcasa por debajo del botón giratorio.

7. Einlegen und Öffnen des Binderückens

7. Chargement et ouverture de la baguette plastique

Bindehebel bis zum Anschlag ganz nach hinten drücken. (im letzten Drittel muß dabei ein etwas stärkerer Federdruck überwunden werden).

Poussez le levier de reliure entièrement en arrière jusqu’à la butée (dans le dernier tiers de la course, il faut surmonter une pression de ressort légèrement plus élevée).

Achtung: Bindehebel muß ganz am Anschlag anliegen, da sich sonst der Binderücken nicht einlegen läßt. Den Plastikbinderücken hinter den Haltekamm so einlegen, daß die Zahnspitzen des Plastikbinderückens nach unten zeigen.

Plastikbinderücken mittels Bindehebel ca. 2/3 öffnen. Achtung: Nicht zu weit öffnen, Überdehnung Rändelschraube an der Vorderseite der Maschine öffnen und nach rechts bis zum Anschlag schieben. Aufziehweite ist so für weitere Bindungen fixiert.

  1. Inserting and opening the combs

Push the black binding handle at the right hand side of the machine to the back until the comb opening levers line up with the vertical comb retaining fingers. In the final portion of this action, additional pressure is required to reach the end of the stroke.

Lay the plastic binding element with its spine behind the vertical retaining fingers and its rings facing upwards through the gaps in the fingers. Open the binding comb by pulling the binding lever forwards until the comb is about two thirds open.

Caution: Do not open the comb too wide as there is danger of over-stretching it which may weaken the plastic.

When the comb has been opened to its desired position, loosen the kurled screw at the front of the machine and slide it to the right until it stops. This sets the opening position when binding a number of documents using the same diameter of comb, and prevents the need to adjust the element opening every time a new comb is opened.

Attention : Le levier de reliure doit coller sur la butée, sinon il est impossible de charger la baguette plastique. Placez la baguette plastique derrière le peigne de retenue de façon à ce que les pointes des dents de la baguette plastique montrent le bas, donc la machine. Ouvrez environ de 2/3 la baguette plastique par l’intermédiaire du levier de reliure . Attention : Ne l’ouvrez pas trop

  • risque d’excès d’extension.

Ouvrez la vis moletée située sur la face de la machine et poussez-la vers la droite jusqu’à la butée. Ainsi, vous aurez fixé l’amplitude d’écartement pour les opérations de reliure ultérieures.

  1. Carga y apertura del lomo encuadernador

Empuje la palanca de encuadernado enteramente hacia atrás hasta el tope (en el último tercio hay que vencer una presión un poco elevada del resorte). ¡Atención! La palanca de encuadernado debe estar adherida al tope, ya que, de lo contrario, no se puede cargar el lomo encuadernador. Emplace el encuadernador plástico detrás del peine de retención de manera que las puntas de diente del encuadernador plástico apunten hacia abajo a la máquina. Abra de aprox. 2/3 el encuadernador plástico mediante la palanca de encuadernado.

¡Atención! No lo abra demasiado - riesgo de extensión excesiva. Abra el tornillo moleteado, que está en la faz de la máquina, y empújelo a la derecha hasta el tope. Así la amplitud de expansión es fijada para los ciclos de encuadernación ulteriores.

Stanzgut plan aufstoßen, in den Stanzschacht einführen und exakt an entsprechenden Anschlag anstellen ( A 4 rechts, A 5 links).

Darauf achten, daß das Papier plan im Stanzschacht steht, evtl. nochmals ausrichten. Max. Stanzkapazität mit 80 g Papier ca. 20 Blatt. Durch Drücken des Fußschalters wird der Stanzvorgang ausgelöst.

Set the book upright, binding side to the bottom. Jog the book to align the pages. Take pages from the top, starting with the front cover. Insert paper into the punching slot (max. 25 pages 70-80g/m²). Adjust the paper guide (DIN A4 right, DIN A5 left). Paper must be centered on the punch pins. If not, align it again. Press foot pedal. Motor starts and punches the pages.

Egalisez les ouvrages à perforer, introduisez-les dans la gorge de perforation et placez-les exactement contre la butée en question (( A 4 à droite, A 5 à gauche). Veillez à ce que le papier soit à fleur dans la gorge de perforation, réalignez-le le cas échéant. Capacité de perforation max. environ 20 feuilles (papier de 80 g/m²). Appuyez sur l’interrupteur à pédale pour déclencher un cycle de perforation.

Empareje los bordes de las hojas a perforar, cárguelas en el canal de perforación y colóquelas exactamente contra el tope correspondiente ( A 4 a la derecha, A 5 a la izquierda ). Cuide de que el papel esté ras con ras en el canal de perforación, alinéelas otra vez, si hubiere necesidad. Capacidad de perforación máx. aproximadamente 25 hojas (papel de 80 g/m²). El proceso de troquelado se dispara apretando el interruptor de pie.

Perforiertes Papier beidhändig dem Stanzschacht entnehmen und sofort - senkrecht - in den Binderücken einkämmen.

Papier nach vorne ablegen. Wenn erforderlich, Stanzvorgang nochmals wiederholen, z.B. bei dickeren Blocks.

Take the punched paper with both hands and insert it directly onto the open rings of the binding element. In case of thicker books repeat these steps until all pages are punched.

Sortez les feuilles perforées de la gorge de perforation à l’aide des deux mains et insérez-les immédiatement - en position verticale - dans les dents de la baguette plastique. Déposez le papier vers l’avant. Si nécessaire, répétez l’opération de perforation, par ex. lorsque vous façonnez des blocs épais.

  1. Encuadernado
  • Saque el papel perforado con las dos manos del canal de perforación y, acto seguido, cólguelo - en posición vertical - en e encuadernador plástico.

Descarga - deposite el papel hacia delante. Si fuera necesario, repita el proceso de troquelado, p.ej. para encuadernar bloques gruesos.

Page 3 of 3 ยท End of manual

Quick start

  1. Lift the machine out of the box by the sides with two people. It weighs 38 kg (84 lbs). Do not lift it by the binding lever or the waste tray.
  2. Place it on a solid, fully supported work surface. If it has come from a cold room, wait 2 hours before switching it on.
  3. Plug the power cord into the socket on the machine, then into the wall outlet.
  4. Turn on the main switch. The fan starts running.
  5. Press the foot pedal to cycle the punch. The motor only runs while the pedal is pressed.
  6. After inserting all sheets on the comb, push the binding lever all the way back to close the comb, then lift the bound document up off the comb retaining fingers.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not runMain switch off, plug not connected correctly, or no power at the outletCheck that the main switch is on, the power cord is plugged in correctly at both ends and the outlet has power. Page 2
Machine does not run with power connectedBlown fuseUnplug the machine. Use a screwdriver to push out the fuse holder (right side, below the main switch). If the fuse is defective, replace it, press the holder back in and reconnect the power. Do not open the machine; return it to Renz if needed. Page 2

Frequently asked questions

How much does the Renz Combi E weigh?

It weighs 38 kg (83.6 lbs). Renz recommends two people lift it by the sides. See page 2.

Can I add or remove pages after binding?

Yes. With the binding lever pushed fully back, slide the document onto the comb fingers with the comb spine on the punching slot side, then pull the lever toward you to open the comb and add or remove sheets. See page 2.

How do I clean the Combi E?

Wipe it with a dry cloth only and do not use solvents, as the stickers may come off. Empty the waste drawer regularly. See page 2.

What are the electrical specifications?

The manual lists a 250 W, 2.9 A motor and a 14 W, 0.8 A fan, at 240 V 50 Hz (or 115 V 60 Hz). See page 2.