Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 1

Page 1 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 2
Text on page 2

Teilung Pitch Paso Pas de division

ERW

Bedienungsanleitung für kombinierte, elektrische Stanz- und Hand-Bindemaschine Operation Manual for combined, electrical Punch and Binding Machine Instrucciónes de uso de la máquina combinada perforadora-encuadernadora Instructions de service pour la machine à relier et perforer combinée

Meßscala Measuring scale Escala de medición Echelle de mesure

Druckstücke Pins Anulación de punzones Presseur

Papieranschlag DIN A5 Paperguide DIN A5 Tope del papel DIN A5 Butée DIN A5

Papieranschlag DIN A4 mit Klemmschraube Paper guide A4 with attachment screw Tope del papel DIN A4 con tornillo de sujeción Butée du papier DIN A4 Bindehebel avec vis de serrage Binding lever Palanca de encuadernación Stanzschacht Levier de reliure Punching shaft Hueco de perforado Arbre de base

Luftschlitze Air Slots Respiraderos de ventilaciòn Grilles d'aération

Hauptschalter Main switch Interuptor principal Interrupteur principal

Klemmschraube für Maßstab Attachment screw for adjusting slider Tornillo de sujeción de la escala Vis de serrage pour échelle graduée

Sicherung Fuse Fusible Fusible

Maßstab Adjusting scale Escala Graduatión

Fußschalter Pedal Conmutador de pedal Pédale de démarrage

Klemmleiste Wire comb clamping fixture Regleta de sujeción Réglette de serrage

Einsatzgebiet:

max. 25 Seiten 70-80 g/m

Schließbalken Closing bar Barra de cierre Berre de fermeture

Abfallschublade Waste drawer Cajón de desperdicios Tiroir à rognures

Field of Application: Punching of paper

max.25 pages 70-80 g/m

Punching of card stock

max. thickness: 1,5 mm

Punching of plastic foil

max. 2 pages for 0,3 mm

max. 2 Seiten á 0,3 mm

max. Bindedicke 12 mm

ca. 120 Blatt 70-80 g/m

max. binding thickness 12 mm (1/2")

approx. 120 pages 70-80 g/m

Do not punch any other material or metal!

• Vorsicht: Bei starkem Tempearaturwechsel erst nach 2 h einschalten

• Caution: In case of major change of temperature turn on the machine only after 2h.

Wenn das Gerät aus einem kalten Raum kommt, kann sich Kondenswasser gebildet haben.

• Vor dem ersten Einsatz: Einige Probestanzungen durchführen.

Damit wird der Rostschutz von den Stanzstempeln entfernt. So oft wiederholen, bis Stanzlöcher ohne Flecken sind.

• Empfindliche Möbeloberflächen schützen

Das Gerät steht auf weichen Kunststoffüßen. Manche Oberflächen können sich auf Dauer verfärben.

If the machine has been in a cold room, condensation water may be possible.

• Before first use:

Punch scrap paper to clean the rust preventative from the punch dies.

•Protect sensitive furniture surface.

The machine stands on plastic feet. Some surface may become discoloured after time.

Radeinstellung Adjusting scale Edge adjustment Ajuste de profundidad de perforación Alignement échelle graduée

Áreas de utilización: Perforado de papel máx. 25 páginas de 70-80 g/m Perforado de cartón máx. 1,5 mm Perforado de hojas de plastico máx. 2 hojas de 0,3 mm Prosor máximo de encuadernación 12 mm Aprox. 120 hojas de 70-80 g/m No perfore ningún otro material o métal

Domaine d’utilisation: Perforation du papier : 25 feuilles maxi 70 à 80 g/m Perforation du carton : ép. 1,5 mm maxi. Perforation de feuilles de plastique : 2 feuilles de 0,3 mm. Épaisseur de perforation maxi : 12 mm env. soit 120 feuilles de 70 à 80 g/m . Ne perforer aucune autre matière ou métal u

• Precaución: En caso de un cambio brusco en la temperatura, encienda la máquina depués de 2 horas.

• Attention: Lors d'un grand changement de température ne faire fonctionner la machine que 2 heures apres avoir laissé reposer.

Si la máquina ha estado en una habitación fria, puede producirse condensación del agua.

• Antes de su primer uso:

Hacer algunas perforaciónes de prueba. De esta forma se limpian las cuchillas de perforación del aceite que tiene la máquina. Repetir la operación hasta que los punzones queden limpios.

• Proteger las superficies delicades.

Algunas superficies pueden perder color con el tiempo .

Luftschlitze immer frei halten

Keep air slots free

Abgedeckte Luftschlitze führen zu Wärmestau und beschädigen das Gerät.

Covered air slots lead to head accumulation an damage the machine.

Netzanschluß Voltage Conexion a la red Branchement au réseau

Mantener despejados los respiraderos de ventilación.

Si se cubren, la maquina se puede ~ danar.

Si la machine était dans une pièce froide, de l`eau condensèepeut se former.

• Avant la premièren utilisation:

exécuter quelques perforations d’essai. Ainsi, la protection anti-rouille du poinçon sera enlevée. Recommencer jusqu’à ce que le poinçon ne comporte plus de taches.

• Protéger les supports de meuble fragiles.

L'appareil se trouve sur des pieds en matière synthétique. Certains supports peuvent se décolorer avec le temps.

Laisser les grilles d'aération libre.

Des grilles d'aération bloquées entraînent une surchauffe et endommagent l'áppareil.

Page 2 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 3
Text on page 3

Aufstellen und Anschließen Setup and Connect Colocación Mise en place

Einstellen Adjust Ajuste Régler

Schutzkartons entfernen Lieferumfang prüfen

  • Combi-Gerät
  • Fußschalter
  • Elektrokabel
  • Bedienungsanleitung

Gerät aus dem Karton heben. Nicht am Bindehebel hochheben. Gewicht: 38,0 kg, deshalb mit 2 Personen am Maschinenboden anfassen und herausheben.

Stabilen Standort wählen. Der Standort muß voll abgestützt sein. Vorstehende Arbeitsplatten sind ungeeignet.

Remove protective packing and check contents of the box. You should have...

  • Combi-machine
  • Foot Pedal
  • Electrical Plug

Lift the machine out of the box. Choose a stable surface. Do not lift using the binding Place the machine on a stable levers. surface. Shelves are not Weight: 38,0 kg recommended. It is recommend that 2 persons are used to lift the machine.

Connect cable and pedal Connect the machine only to plugs wich are grounded.

Abra el embalaje quitando el cartón de protección y revise el contenido. Vd. debería de tener: Encuardernadora Combi, -Pedal,

  • Cable con el enchufe, Instrucciónes de uso.

Saque la máquina del embalaje. Elija un emplazamiento No la levante por las palancas. estable Peso: 38,0 kg Colocar la encuadernadora en un lugar de trabajo sólido y bien apoyado. No se recomienda colocar la sobre una estanteria.

Conecte el cable y el pedal. Conecte la máquina sólo a enchufes que tengan toma de tierra.

Enlever les cartons de protection Vérifier le contenu:

  • la machine
  • la pédale de démarrage
  • le câble d'alimentation
  • le mode d'emploi

Sortir la machine du carton. Ne pas soulever en tenant le levier de serrage. Poids: 38,0 kg

Choisir un emplacement stable Les plans de travail en porte-àfaux ne conviennent pas.

Elektrokabel anschließen. Nur an Steckdosen mit Schutzkontakt anschließen.

Brancher le câble. Ne brancher que sur des prises d'alimentation terre et neutre.

Durchmesser der Bindeelemente ermitteln Buchblock auf die Kante neben der Maßskala legen. Durchmesser der Bindeelemente ablesen (z.B. 3/8").

Determination of the diameter Put the back on the edge against the measuring scale. Read the diameter of the binding element. (e.g. 3/8")

Determinación del diametro Colocar el bloque de hojas en la escala de medidas para saber el diametro correcto del encuadernador. p. ej. 3/8”

Rechercher le diamètre des éléments de reliure. Mettre le livre non relié sur le bord, à côté de l’échelle graduée. Lire le diamètre des éléments de reliure (p. ex. 3/8").

Maßstab auf Durchmesser einstellen Klemmschraube lösen, Maßstab ermitteln, Durchmesser einstellen, Klemmschrauben anziehen.

Randabstand auf Durchmesser einstellen. Knopf drehen Zeiger des Knopfes auf den passenden Durchmesser drehen (z.B. 3/8") größerer Ø = größerer Rand

Scale for adjusting the diameter Release attachment screw, determine scale, adjust diameter, tighten attachment screw.

Adjust distance edge to according diameter turn knob Turn knob index to the according diameter (e.g. 3/8") bigger Ø = bigger edge. Ajuste al diámetro la

Escala para ajustar el diámetro. Desenrroscar la rosca de ajuste,colocar en el diametro correspondiente y apretar la rosca.

Profundidad de margén. Gire el boton. Ajustar el margen segun diámetro girando el botón. A Mayor diámetro mayor margen.

Régler un diamètre sur l’échelle graduée Desserrer la vis de serrage. Régler le diamètre. Serrer la vis de serrage.

Calibrer le diamètre. Tourner le bouton de l’écartement des bords. Amener l’aiguille sur le diamètre qui convient (p. ex. 3/8"). Ø maxi = bord plus grand.

A4-Format einstellen: Anschlag rechts festschrauben,

  1. Druckstück von links ziehen (34 Schlaufen) A5-Format einstellen:

Anschlag links festschrauben,

  1. Druckstück von links und 10.

Druckstück von rechts ziehen (24 Schlaufen)

Adjust format A4 paper: Screw down the right paper guide, pull 4th pin from left (34 loops). Adjust format A5 paper: Screw down the left paper guide, pull 4th pin from left and 10th pin from the right (24 loops).

Ajuste el formato A4: Atornille el tope a la derecha. Levantar el 4º compresor por la izquierda (34 anillas). Atornille el tope a la izquierda. Levantar el 4° punzon de la izquierda y el 10° por la derecha (24 anillas).

Réglage du format A4: Serrer la butée de droite, Tirer la 4e pièce de pression de gauche (34 boucles). Réglage du format A5: Serrer la butée gauche. Tirer la 4e pièce de pression de gauche et la 10e pièce de pression de droite (24 boucles).

Page 3 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 4
Text on page 4

Einlegen Insert Colocación Mise en place

Bindeelemente vor die Klemmleiste legen Kammzähne nach oben.

Klemmleiste drücken Hinterkante nach unten drücken, Vorderkante öffnet sich.

Bindeelemente unter die Klemmleiste schieben Klemmleiste hält das Bindeelement fest, wenn gestanztes Papier eingekämmt wird.

Klemmleiste loslassen, ggf. Bindeelement senkrecht ausrichten

Lay binding element in front of the clamping fixture Small loops on top, facing rear.

Press down clamping fixture Press back edge and front side will open.

Push binding element under the clamping fixture Clamping fixture holds binding element during insertion of the punched paper.

Release clamping fixture possibly adjust binding element vertically

Coloque el encuadernador frente a la bandeja de sujección

Oprima la regleta de sujeción Presionar la bandeja de sujección en su parte trasera y se levantará la parte delantera

Colocar el encuadernador debajo de la bandeja de sujección. Esta mantendra sujeta el encuadernador para introducir al papel perforado.

Suelte la regleta de sujeción y si es preciso ponga en línea verticalmente el elemento de encuadernación Si es preciso, adapte la regleta de deslizamiento

Appuyer sur la réglette de serrage. Appuyer sur la partie arrière de la règle, la partie avant s’ouvre.

Pousser la réglette de reliure sous la réglette de serrage. La réglette de serrage maintient l’élément de reliure si le papier perforé est introduit dans le peigne.

Relâcher la réglette de serrage ; redresser éventuellement l’élément de reliure verticalement. Si nécessaire, ajuster la réglette de poussée.

Verschluß der Drahtkammbindung soll innen liegen Kammverschluß muß innen liegen.

Buchblock aufstellen Heftrücken nach oben. Rückseite nach vorn klappen Deckblatt und Rückseite liegen jetzt hintereinander.

Buchblock drehen. Deckblatt und Rückseite liegen unten. Seiten von oben abnehmen.

The seam of the closed binding element should be inside the book Not outside the covers.

Set the book upright, binding side to the top, place theback cover in front.The front cover should be behind the back cover.

Turn the book over, covers are underneath. Take pages from the top.

El cierre del encuadernador debe quedar por dentro y no por fuera de las cubiertas.

Colocar el bloque con la parte a taladrar hacia arriba, con la contraportada al principio. La portada debe estar detrás de la contraportada.

Iguale el bloque de hojas

Colocar el bloque a encuadernar con las cubiertas hacia abajo. Tome las hojas por arriba

La fermeture de la reliure en fil doit se trouver à l’intérieur. La fermeture à peigne doit se trouver à l’intérieur.

Répartir le livre non relié. Faire butter les feuilles vers le haut. Rabattre la couverture vers l’avant. Couverture et dos se trouvent maintenant l’un derrière l’autre.

Égaliser le livre non relié.

Retourner le livre non relié. Couverture et dos se trouvent au-dessous. Retirer les feuilles par le haut.

Mettre les éléments de reliure devant la réglette de serrage, les dents du peigne vers le haut.

Vorbereiten Prepare Preparación Préparation

Page 4 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 5
Text on page 5

Stanzen Punch Perforación Perforation

max. 25 Seiten (80 g/m dicke Buchblocks in Lagen stanzen Plastik und dickere Deckblätter nur einzeln stanzen.

Papierlage in Stanzschacht einführen und am Anschlag anstellen DIN A4 rechts anstellen, Papier muß plan stehen, evtl. noch einmal ausrichten.

DIN A5 links am Anschlag anstellen.

Stanzhebel nach vorn bis zum Anschlag drücken und wieder ganz zurückführen Maschine mit der anderen Hand halten.

Punch max. 25 pages 80 g/m punching: 15 – 20 pages Punch plastics and thicker covers separately.

Insert paper into punching slot, slide the paper against the paper guide Adjust A4 format at the right side, paper must stand evenly, if not align it again.

Adjust A5 format at the left side.

Press punching lever forward until it stops, then return to original position Hold the machine with the other hand.

Max. capacidad de perforación: 25 hojas de 70/80 r´gr./m² Es aconsejable perforar 15 - 20 hojas cada vez. Perforar el plastico y tapas gruesas separadamente

Introduzca el bloque de papel en la cavidad de perforado y llévelo al tope Ajuste a la derecha del tope el tamaño DIN A4, el papel debe estar plano y debe alinearse de nuevo si fuera preciso

Ajuste a la izquierda del tope el tamaño DIN A5

Presionar la palanca hacia delante hasta el fin y vuelvala a su posisión original. Sujete la maquina con la otra mano

Perforer des livres non reliés par paquets d’un maximum de 25 feuilles (80 g/m) Ne perforer les couvertures en plastique et plus épaisses qu’à l’unité.

Introduire les paquets de papier dans le puits de perforation et mettre en place la butée. Mettre les A4 contre la butée à droite. Le papier doit être à plat. Régler à nouveau éventuellement.

Mettre en place gauche, contre la butée, les DIN A5.

Appuyer sur le levier de perforation vers l’avant jusqu’à ce qu’il bute et ramener à fond en arrière. Maintenir la machine avec l’autre main.

Einkämmen Insert Introducción Introduction dans les peignes

Bei dickeren Buchblocks Schritte 5 und 6 wiederholen, bis alle Seiten gestanzt sind

For thicker books, repeat steps five and six until all pages are punched

gestanztes Papier beidhändig entnehmen

gleich in das Bindeelement einkämmen

Remove punched paper from the punching slot

Insert paper onto the binding element

Tome el papel perforado con ambas manos

e introdúzcalo en el elemento de encuadernación

Enlever le papier perforé avec les deux mains.

Introduire immédiatement dans les peignes de l’élément de reliure.

Para bloques de hojas de mayor grosor, repita las operaciones 5 y 6 hasta que todas las hojas estén perforadas

Pour les livres non reliés épais, recommencer les opérations 5 et 6 jusqu’à ce que toutes les feuilles soient perforées.

Page 5 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 6
Text on page 6

Anlegen Adjust Colocación Mise en place

Bindeelement unter der Klemmleiste herausheben, mit Buchblock entnehmen Papier so anfassen, daß es nicht aus dem Bindeelement rutscht.

Bindeelement unter den Schließbalken schieben

Bindeelement muß senkrecht an der Rückwand des Schließbalkens stehen Öffnung des Bindeelements zeigt zur Rückwand.

After the paper has been placed on the binding element, remove the paper with the element from the clamping fixture Hold the paper that it does not slide out of the binding element.

Put binding element under the closing bar

Binding element must stand vertically at the back of the closing bar With opening of the binding element to the back.

Oprima la regleta de sujeción

Levante el elemento de encuadernación debajo de la regleta y sáquelo con él. Tome con las manos el papel de modo que no se deslice fuera del elemento de encuadernación

Deslice el elemento de encuadernación debajo de la barra de cierre

El elemento de encuadernación debe estar perpendicular respecto a la barra de cierre. La abertura del elemento de encuadernación mira hacia la cubierta posterior

Appuyer sur la réglette de serrage

Soulever l’élément de reliure sous la réglette de serrage, l’enlever avec le livre non relié. Saisir le papier de façon telle qu’il ne glisse pas de l’élément de reliure.

Pousser l’élément de reliure sous la barre de fermeture.

L’élément de reliure doit se trouver verticalement contre la paroi arrière de la barre de fermeture. L’ouverture de l’élément de reliure est dirigé vers la paroi arrière.

Bindehebel bis zum Anschlag nach vorn drücken und wieder zurückführen Bei größerem Bindedurchmesser mehr Kraft einsetzen.

Bindung zu offen: Schließbalken etwas tiefer einstellen Klemmschraube lösen und etwas nach links schieben. Klemmschraube festziehen. Bindehebel noch einmal drücken.

Bindung zu eng: Schließbalken etwas höher einstellen Klemmschraube lösen und etwas nach rechts schieben, Klemmschraube festziehen. Nächstes Exemplar richtig schließen.

Press binding lever forward until it stops and back again For bigger diameters use more force.

Binding under closed: Adjust closing bar a little deeper Release attachment screw and move it slightly to the left. Fix attachment screw. Press binding lever again.

Binding over closed: Adjust closing bar a little higher Release attachment screw and move it slightly to the right. Fix attachment screw. Close next book.

Presione la palanca de encuadernación hacia delante hasta el tope y devuélvala hacia atrás. A mayor diámetro de encuadernación, mayor fuerza se necesita

Unión demasiado abierta: ajuste la barra de cierre algo más abajo Afloje el tornillo de sujeción desplázandolo un poco hacia la izquierda. Apriételo. Presione de nuevo la palanca de encuadernación

Unión demasiado estrecha. Ajuste algo más alta la barra de cierre Afloje el tornillo de sujeción desplázandolo un poco hacia la derecha. Apriételo. Cierre correctamente el siguiente ejemplar.

Appuyer sur le levier de reliure jusqu’à ce qu’il butte et le ramener. Pour les gros diamètres de reliure, recourir à plusieurs opérations.

Reliure trop ouverte : régler la barre de fermeture un peu plus profond. Desserrer la vis de serrage et pousser un peu vers la gauche. Serrer la vis de serrage ; appuyer à nouveau sur le levier de reliure.

Reliure trop serrée: régler la barre de fermeture un peu plus haut. Desserrer la vis de serrage et pousser un peu vers la droite. Serrer la vis de serrage. L’exemplaire suivant fermera convenablement.

Schliessen Close Cierre Fermeture

Page 6 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 7
Text on page 7

Fertig Ready Acabado Terminé

Teilung/Pitch/Paso/Pas

Rückseite nach hinten klappen

Turn back cover over

Gire hacia atrás la hoja posterior

Rabattre le dos vers l’arrière.

mm

Zoll - mm Inch - mm

Pulgadas - mm

Pouce - mm

Technische Daten 230 V 50 Hz /250 W Sicherung 5 x 20 4 A träge Gewicht 38 kg

Technical data 230 V 50 Hz / 250 W Fuse 5 x 20 4 A slow Weight 38 kg

Datos técnicos 230 V 50 Cc /250 W Fusible 5 x 20 4 A lento Peso 38 kg

Données techniques 230 V 50 Hz / 250 W Fusible 5 x 20 4 A lent Poids 38 kg

Bindelänge

Binding length Longitud de encuadernación Longuer à relier

Loops Loops Anillas Anneaux

Bindelänge Binding length

Longitud de

encuadernación Longuer à relier

Loops Loops

Anillas

Anneaux

63 mm 76 mm 89 mm 102 mm 114 mm 127 mm 140 mm 152 mm 165 mm 178 mm 190 mm

210 mm 216 mm 229 mm 241 mm 254 mm 267 mm 280 mm 297 mm 305 mm 317 mm 330 mm

für ca. Blätter 70-80 g/m²

maximum sheets 70-80 g/m²

Nº aprox. de hojas de 70 - 80 g/m²

Nº approx. de feuilles 70 - 80 g/m²

Page 7 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 8
Text on page 8

Warten Maintenance Limpieza Entretien

Nur trocken reinigen Mit trockenem oder feuchtem Tuch abwischen. Keine Lösungsmittel verwenden, Aufdrucke können sich lösen.

Cleaning Wipe with a dry or moist cloth. Do not use solvents, sticker may detach.

Limpieza sólo en seco Limpie con un paño seco o humedecido. No utilice disolventes. Las huellas se pueden borrar.

Ne nettoyer qu’à sec Essuyer avec un chiffon sec ou humide. Ne pas utiliser de solvant. Les empreintes peuvent s’effacer.

Schublade regelmäßig leeren Schublade herausziehen und Papierabfall ausschütten.

Empty drawer from time to time Pull out drawer and empty out the papershavings.

Vaciar la bandeja del desperdicio del papel periodicamente

Vider le tiroir régulièrement Sortir le tiroir et jeter les rognures de papier.

Gerät nicht öffnen Gerät darf nur vom Fachpersonal geöffnet werden.

Do not open the machine The machine is only to be opend and serviced by an authorized service center.

No abra la máquina La máquina sólo la puede abrir y reparar la empresa de servicios autorizada.

Ne pas ouvrir l'apparail Seul un technicien doit ouvrir l'appareil.

Page 8 of 9

Renz ERW 3:1 Wire Binding Machine with Electric Punch Instruction Manual, page 9
Text on page 9

Sicherung wechseln Change of Fuse Cambio de fusible Changer le fusible

Unplug the machine Desenchufar la máquina

Retirer la prise de courant

Sicherungshalter mit Schraubendreher herausdrücken Pry out fuse holder with screw driver Desenroscar la tapa del fusible con un destornillador Enlever la couverture du fusible avec un tourne-vis

Sicherung kontrollieren Wenn Sicherung defekt.... Check fuse If fuse is defective.... Comprobar el fusible.... Controller le fusible. Si le fusible est defectueux....

Ersatzsicherung anstelle der defekten Sicherung einsetzen Ersatzsicherung kaufen Get a new replacement fuse Put in replacement fuse Si está fundido Colocar un fusible nuevo Asegurese de de tener un fusible de repuesto Acheter un fusible de rechange Remplacer le fusible défectueux

Sicherungshalter einsetzen und eindrücken Netzstecker einstecken Put in fuse holder and press it in. Connect main plug Meter el fusible en su tapa y presionar Conectar el enchufe principal Insérer la couverture du fusible et brancher la prise de courant.

Page 9 of 9 ยท End of manual

Quick start

  1. Lift the machine (38 kg) out of the box with two people, holding it by the base, not the binding lever. Place it on a stable surface and connect the cable and foot pedal to a grounded outlet.
  2. If the machine came from a cold room, wait 2 hours before switching it on. Before first use, punch scrap paper to clean rust preventative from the dies.
  3. Lay the book against the measuring scale to read the wire diameter, set the scale with the attachment screw, then turn the edge-distance knob to the same diameter.
  4. For A4, screw down the right paper guide and pull the 4th pin from the left (34 loops). For A5, screw down the left guide and pull the 4th pin from the left and 10th from the right (24 loops).
  5. Press the back edge of the clamping fixture, slide the wire under it with the small loops on top facing the rear, and release.
  6. Punch 15–20 sheets at a time against the paper guide and hang each stack on the wire.
  7. Lift the book and wire out of the fixture, place the wire vertically under the closing bar with the opening to the back, and push the binding lever forward to the stop and back.

Troubleshooting

ProblemLikely causeFix (from the manual)
Wire binding is closed too loosely (too open)The closing bar on the ERW is set too high for the book thickness.Loosen the clamping screw and slide the closing bar slightly to the left to set it a little deeper. Tighten the screw and press the binding lever again. Page 6
Wire binding is closed too tightThe closing bar is set too deep.Loosen the clamping screw, slide the closing bar slightly to the right to set it a little higher, and tighten the screw. Close the next book correctly. Page 6
Punch lever is hard to push or pages will not punchThe stack is too thick, or plastic or heavy covers are punched with the paper.Punch no more than 25 pages of 80 g/m paper at a time. The manual advises 15 to 20 pages per punch. Punch plastic and thicker covers one at a time. Page 5
Punched holes sit off-center on A4 or A5 paperThe paper is not flat or not against the stop.Slide A4 paper to the stop on the right and A5 to the stop on the left. Keep the paper flat and realign it if needed. Page 5
Pages slip out of the binding element when it is movedThe paper is not held while the element is lifted from under the clamping fixture.Hold the paper so it cannot slide out as you lift the element and book out. Then slide the element under the closing bar with its opening toward the back. Page 6
The wire seam shows outside the coversThe closed binding element is placed with its seam on the outside.Set the binding element so the seam ends up inside the book. Load it with the small loops up, facing the rear. Page 4

Frequently asked questions

How many sheets can the Renz ERW punch?

Up to 25 sheets of 70–80 g/m² paper, 1.5 mm card stock or two 0.3 mm plastic sheets. 15–20 sheets per punch is recommended. See page 2 and page 5.

What is the maximum binding thickness?

12 mm (1/2"), about 120 sheets of 70–80 g/m² paper. See page 2.

How many loops does it punch?

34 loops on A4 and 24 loops on A5 (3:1 pitch). See page 3.

How heavy is the ERW?

38 kg. Renz recommends two people lift it. See page 3.

How do I maintain it?

Wipe with a dry or damp cloth, no solvents, and empty the waste drawer from time to time. Do not open the machine. See page 8.