Renz PBS 340 Manual, page 1

Page 1 of 3

Renz PBS 340 Manual, page 2
Text on page 2

Bedienungsanleitung Manuelle Handbindemaschine für Plastikbindung Operation manual Manual binding machine for plastic comb binding Mode d´emploi Relieuse manuelle pour la reliure à baguettes plastiques Instrucciónes de servicio Máquina encuadernadora manual para canutillos plasticos

RENZ PBS 340

Die Maschine und ihre Teile La machine et ses éléments

The machine and its parts La maquina y sus componentes

Haltekamm Comb holder Peigne de retenue Peine de retención

Bindehebel binding lever levier de reliure palanca de encuadernado

Rändelschraube knurled screw vis moletée tornillo moleteado

Halterung für MBS Module Holding device for MBS moduls Dispositif de serrage pour modules MBS Dispositivos para los módulos MBS

Aufziehhaken opening hooks crochets d´écartement ganchos de expansión

Länge Lenghts Longeur Largo 50 cm / 19,7“

Breite Höhe Width Height Largeur Hauteur Ancho Altura 19 cm / 7,5“ 17 cm / 6,7“

Gewicht / Weight / Poids / Peso 4,3 kg / 9,5 lbs.

Page 2 of 3

Renz PBS 340 Manual, page 3
Text on page 3

Wird das Modul als Einzelgerät verwendet , ist die Modulhalterung notwendig. Gerät dann wie oben gezeigt in die Halterung einsetzen.

Bei Einsatz mit der Stanzmaschine DTP 340 M, Gerät direkt an die Stanzmaschine anbauen. Anwendung DTP 340 M , siehe separate Gebrauchsanleitung.

If the module is used as a single unit the holding device is necessary. Insert unit holding device as shown above.

If the module is used together with the punch machine DTP 340 M, install the unit directly at the punch machine. For application on DTP 340 M, see separate operation manual.

Si le module est utilisé comme appareil individuel, il faudra le fixer par l’intermédiaire d’un dispositif de serrage. Dans ce cas, posez l’appareil sur ce dispositif selon l’illustration ci-dessus.

S’il est utilisé avec la machine à perforer DTP 340 M, rapportez l’appareil directement sur cette machine. Pour l’exploitation de la DTP 340 M, voir le mode d’emploi séparé.

Si se utiliza el módulo como aparato individual, se necesitará el dispositivo fijador. Inserte entonces el aparato en dicho dispositivo según la ilustración arriba indicada.

Si se lo utiliza con la troqueladora DTP 340 M, adose el aparato directamente a esta troqueladora. Para la explotación de la DTP 340 M, véase el modo de empleo separado.

Bindehebel muß ganz am hinteren Anschlag stehen. Binderücken in Haltekamm einlegen, Zähne müssen nach hinten unten zeigen. Binderücken mit Bindehebel ca. 2/3 öffnen.Rändelschraube öffnen, nach rechts bis zum Anschlag schieben und wieder festziehen. Aufziehweite ist so für weitere Bindvorgänge fixiert

Das perforierte Papier senkrecht in den Binderücken einkämmen und nach vorne ablegen. Bei dickeren Blocks Vorgang wiederholen. Sind alle Blätter eingekämmt, Bindehebel ganz nach hinten bis zum Anschlag drücken und gebunden Block nach oben herausnehmen. Fertig!

Push binding lever back until it really stops. Lay plastic comb behind the comb holder so that the prongs of the plastic comb binding face downwards. Open plastic comb by pulling the binding lever forward until the comb is about two-thirds open. Loose the knurled screw and push it to the right until it stops. So the screw sets the opening widht for further binding.

Insert the punched paper vertically onto the fingers of the open plastic comb and lay it down towards you. For thicker books repeat this process. Close plastic comb by returning the binding lever to the stop. Lift the completed ´book upwards to remove. Ready!

Il faut que le levier de reliure soit collé contre la butée arrière. Placez le dos de reliure dans le peigne de retenue de manière à ce que ses dents soient orientées vers le bas arrière. Ouvrez le dos de reliure d’env. 2/3 à l’aide du levier de reliure. Desserrez la vis moletée, poussez-la vers la droite jusqu’à la butée, puis resserrez-la. Ainsi, l’amplitude d’écartement sera fixée pour les opérations de reliure suivantes.

Insérez le papier perforé perpendiculairement dans les dents du dos de reliure et déposez-le vers l’avant. Répétez cette opération s’il s’agit de blocs épais. Lorsque toutes les feuilles sont insérées, poussez le levier de reliure entièrement en arrière jusqu’à la butée, puis retirez le bloc relié vers le haut. Ça y est!

La palanca de encuadernado debe estar pegada al tope trasero. Cargue el lomo encuadernador en el peine de retención de manera que los dientes apunten hacia abajo atrás. Abra el lomo encuadernador de aprox. 2/3 mediante la palanca de encuadernado. Suelte el tornillo moleteado, empújelo hacia la derecha hasta el tope, luego apriételo de nuevo. Así la amplitud de expansión estará fijada para los encuadernados ulteriores.

Entre las hojas perforadas perpendicularmente en el lomo encuadernador y deposítelas hacia delante. Repita está operación si se trata de bloques gruesos. Cuando todas las hojas están entradas en el lomo encuadernador, empuje la palanca de encuadernado enteramente hacia atrás hasta el tope y retire el bloque encuadernado hacia arriba. ¡Ya está! 08 / 2002 - 971 000001

Page 3 of 3 · End of manual

Quick start

  1. Used alone, insert the module into its holding device. Used with the DTP 340 M punch, mount it directly on the punching machine.
  2. Push the binding lever all the way back until it stops.
  3. Lay the plastic comb behind the comb holder with the prongs facing down and to the rear.
  4. Pull the binding lever forward until the comb is about two-thirds open.
  5. Loosen the knurled screw, push it right to the stop and retighten it. This fixes the opening width for further binding.
  6. Hang the punched paper vertically on the open comb and lay it toward you. Repeat for thicker books.
  7. Push the binding lever fully back to close the comb and lift the bound book out.

Troubleshooting

ProblemLikely causeFix (from the manual)
Comb does not sit right in the holderComb is turned the wrong wayLay the plastic comb behind the comb holder with the prongs facing down. Push the binding lever fully back first. Page 3
Comb opens too little or too much on repeat jobsOpening width is not setOpen the comb about two thirds with the binding lever. Loosen the knurled screw, push it right to the stop, and tighten it. This sets the opening width for later jobs. Page 3
Thick book will not fit on the combAll pages inserted at onceInsert the punched paper vertically onto the comb fingers and lay it forward. Repeat for thicker books. Page 3
Bound book will not come offComb is not fully closedPush the binding lever fully back to the stop to close the comb, then lift the book up and out. Page 3
Unit is not steady when used aloneUsed as a single unit without the holding deviceUse the holding device when the module is used as a single unit. Insert the unit into it. Page 3

Frequently asked questions

Can the PBS 340 be used without the DTP 340 M?

Yes. Used as a single unit it needs the holding device; with the DTP 340 M it mounts directly on the punch. See page 3.

How far should I open the plastic comb?

About two-thirds open, using the binding lever. See page 3.

How do I keep the same comb opening for every book?

Loosen the knurled screw, push it to the right until it stops and retighten it; this fixes the opening width for further binding. See page 3.