

Page 1 of 8

Text on page 2
BEDIENUNGSANLEITUNG \ OPERATION MANUAL \ INSTRUCCIÓNES \ INSTRUCTIONS
SRW 360
KOMBINIERTE STANZ- UND HANDBINDEMASCHINE
COMBINED PUNCH AND BINDING MACHINE
Teilung / pitch / paso / pas
MÁQUINA COMBINADA PERFORADORA-ENCUADERNADORA
MACHINE À RELIER ET PERFORER COMBINÉE
Klemmschraube für Maßstab Attachment screw for adjusting slider Tornillo de sujeción de la escala Vis de serrage pour échelle graduée
Meßscala Measuring scale Escala de medición Echelle de mesure
Druckstücke Pins Punzones Presseur
Papieranschlag mit Klemmschraube Paper guide with attachment screw Tope del papel con tornillo de sujeción Butée du papier avec vis de serrage
Stanzhebel Punching lever Palanca de perforado Levier de perforation
Stanzschacht Punching shaft Hueco de perforado Puits de perforation
Randeinstellung Adjusting scale Edge adjustment Ajuste de profundidad de perforación Alignement échelle graduée
Bindehebel Binding lever Palanca de encuadernación Levier de reliure
Haltevorrichtung für Bindeelemente Holding fixture for binding elements Dispositif d‘insertion des éléments métalliques Dispositivo de retención de elementos de alambre
Abfallschublade Waste drawer Cajón de desperdicios Tiroir à rognures
Schließbalken mit abnehmbarer Schließleiste Closing bar with removable closing rail Barra de cierre con regleta desmontable Barre de fermeture avec protection amovible
Einsatzgebiet: Papier stanzen max. 22 Seiten 70-80 g/m Karton stanzen max. 1,5 mm Kunststoff-Folien stanzen max. 1 Seite á 0,3 mm max. Bindedicke 13,5 mm ca. 135 Blatt 70-80 g/m Keine anderen Materialien oder Metalle stanzen!
Field of application: Punching of paper max. 22 pages 70/80 g/m - 20 # stock Punching of card stock max. thickness: 1,5 mm Punching of plastic foil max. 1 page for 0,3 mm thickness max. binding thickness 13,5 mm(9/16“) appr. 135 pages 70/80 g/m-20 # stock Do not punch any other material or metal!
Áreas de utilización: Perforado de papel máx. 22 páginas de 70-80 g/m Perforado de cartón máx. 1,5 mm Perforado de hojas de plastico máx. 1 hoja de 0,3 mm Grosor máximo de encuadernación 13,5 mm Aprox. 135 hojas de 70-80 g/m No perfore ningún otro material o métal!
Domaine d’utilisation: Perforation du papier : 22 feuilles maxi. 70 à 80 g/m Perforation du carton : épaisseur 1,5 mm maxi. Perforation de feuilles de plastique : 1 feuille de 0,3 mm. Épaisseur de relier maxi. 13,5 mm soit environ 135 feuilles de 70-80 g/m . Ne perforer aucune autre matière ou métal!
- Vor dem ersten Einsatz:
Einige Probestanzungen durchführen. Damit wird der Rostschutz von den Stanzstempeln entfernt. So oft wiederholen, bis Stanzlöcher ohne Flecken sind.
- Before first use:
Punch scrap paper to clean the rust preventative from the punch dies.
- Antes de su primer uso:
Hacer algunas perforaciónes de prueba. De esta forma se limpian las cuchillas de perforación del aceite que tiene la máquina. Repetir la operación hasta que los punzones queden limpios.
- Avant la premièren utilisation: exécuter quelques perforations d’essai. Ainsi, la protection anti-rouille du poinçon sera enlevée. Recommencer jusqu’à ce que le poinçon ne comporte plus de taches.
- Empfindliche Möbeloberflächen schützen.
Das Gerät steht auf weichen Kunststofffüßen. Manche Oberflächen können sich auf Dauer verfärben.
- Protect sensitive furniture surface.
The machine stands on plastic feet. Some surface may become discoloured after time.
- Proteger las superficies delicades.
Algunas superficies pueden perder color con el tiempo.
- Protéger les supports de meuble fragiles.
L‘appareil se trouve sur des pieds en matière synthétique. Certains supports peuvent se décolorer avec le temps.
Page 2 of 8

Text on page 3
AUFSTELLEN UND ANSCHLIESSEN \ SETUP AND CONNECT \ COLOCACIÓN \ MISE EN PLACE
Schutzkartons entfernen Lieferumfang prüfen
- kombinierte Stanz- und Bindemaschine
- Bedienungsanleitung
Gerät aus dem Karton heben. Nicht am Bindehebel hochheben. Gewicht: 15,5 kg
Stabilen Standort wählen. Der Standort muß voll abgestützt sein. Vorstehende Arbeitsplatten sind ungeeignet.
Remove protective packing and check contents of the box. You should have:
- combined punch and binding machine
- operating manual
Lift the machine out of the box. Do not lift using the binding levers. Weight: 15,5 kg / 34,10 lbs.
Choose a solid surface. Place the machine on a solid surface. Shelves are not recommended.
Abra el embalaje quitando el cartón de protección y revise el contenido. Vd. debería de tener:
- encuardernadora combinada
- instrucciónes de uso.
Saque la máquina del embalaje. No la levante por las palancas. Peso: 15,5 kg
Elija un emplazamiento estable Colocar la encuadernadora en un lugar de trabajo sólido y bien apoyado. No se recomienda colocar la sobre una estanteria.
Enlever les cartons de protection Vérifier le contenu:
- la machine combinée pour perforation et reliure
- le mode d‘emploi
Sortir la machine du carton. Ne pas la soulever en tenant le levier de serrage. Poids: 15,5kg
Choisir un emplacement stable. Les plans de travail en porte-àfaux ne conviennent pas.
EINSTELLEN \ ADJUST \ AJUSTE \ RÉGLER
Durchmesser der Bindeelemente ermitteln. Buchblock auf die Kante neben der Maßskala legen. Durchmesser der Bindeelemente ablesen (z.B. 3/8“).
Maßstab auf Durchmesser einstellen. Klemmschraube lösen, Maßstab ermitteln, Durchmesser einstellen, Klemmschrauben anziehen.
Randabstand auf Durchmesser einstellen. Knopf drehen. Zeiger des Knopfes auf den passenden Durchmesser drehen (z.B. 3/8“) größerer Ø = größerer Rand
A 4 Format einstellen: (34 Loops)
35. Druckstück ziehen A 5 Format einstellen: (24 Loops)
25. Druckstück ziehen
Determination of the diameter. Put the back on the edge against the measuring scale. Read the diameter of the binding element (e.g. 3/8“).
Scale for adjusting the diameter Release attachment screw, determine scale, adjust diameter, tighten attachment screw.
Adjust distance edge to according diameter turn knob. Turn knob index to the according diameter (e.g. 3/8“) bigger Ø = bigger edge.
Adjust size A 4 paper: (34 loops). pull 35th pin. Adjust size A 5 paper:(24 loops). pull 25th pin Adjust size 11“ paper: (32 loops). pull 33th pin. Adjust size 8,5“ paper: (25 loops). pull 26th pin.
Determinación del diametro. Colocar el bloque de hojas en la escala de medidas para saber el diametro correcto del encuadernador. p. ej. 3/8”
Escala para ajustar el diámetro. Desenrroscar la rosca de ajuste,colocar en el diametro correspondiente y apretar la rosca.
Profundidad de margén. Gire el boton. Ajustar el margen segun diámetro girando el botón. (p.ej. 3/8“) A mayor diámetro mayor margen.
Ajuste el formato A 4:(34 anillas). Levantar el 35º punzon Ajuste el formato A5: (24 anillas). Levantar el 25° punzon
Rechercher le diamètre des éléments de reliure. Mettre le livre non relié sur le bord, à côté de l’échelle graduée. Lire le diamètre des éléments de reliure (p. ex 3/8“).
Régler un diamètre sur l’échelle graduée. Desserrer la vis de serrage. Régler le diamètre. Serrer la vis de serrage.
Calibrer le diamètre. Tourner le bouton de l’écartement des bords. Amener l’aiguille sur le diamètre qui convient (p. ex. 3/8“). Ø maxi = bord plus grand.
Réglage du format A4: (34 boucles). Tirer la 35e pièce de pression Réglage du format A5: (24 boucles). Tirer la 25e pièce de pression
Page 3 of 8

Text on page 4
EINSTELLEN \ ADJUST \ AJUSTE \ RÉGLER
ø mm 5,5 - 25,4 ø inch 3/16“ - 1“
ø mm 28,5 - 38 ø inch 1 1/8“ - 1 1/2“
Schließleiste aufsetzen oder abnehmen. ø 5,5 - 25,4 mm (ø 3/16 - 1“) Druckknöpfe an beiden Seiten drücken und Schließleiste nach vorne aufsetzen oder abziehen.
Schließleiste entsprechend ø drehen.
Schließleiste aufsetzen oder abnehmen. ø 28,5 - 38 mm (ø 1 1/8 - 1 1/2“) Druckknöpfe an beiden Seiten drücken und Schließbalken nach vorne aufsetzen oder abziehen.
Papieranschlag auf entsprechendes Format einstellen. Feststellschraube an der Rückseite lösen, Anschlag verschieben, Feststellschraube anziehen.
Removal or installation of the closing rail. ø 5,5 - 25,4 mm (ø 3/16 - 1“) Push buttons on both sides and pull rail or push back.
Turn the closing rail according to the ø.
Removal or installation of the closing rail. ø 28,5 - 38 mm (ø 1 1/8 - 1 1/2“) Push buttons on both sides and pull rail or push back.
Adjusting paper guide to the corresponding paper size. Release attachment screw on the rear, adjust paper guide and fasten attachment screw.
Superponga o retire la regleta de cierre. ø 5,5 - 25,4 mm (ø 3/16 - 1“) Apretar los bottones en ambos lados y retire o superponga la regleta de cierre.
Girar la regleta de cierre correspondiente al ø.
Superponga o retire la regleta de cierre. ø 28,5 - 38 mm (ø 1 1/8 - 1 1/2“) Apretar los bottones en ambos lados y retire o superponga la regleta de cierre.
Ajustar el tope del papel al tamaño correspondiente Afloje el tornillo de sujeción, ajuste el tope de papel y aprete el tornillo.
Mettre ou ôter la barre de fermeture. ø 5,5 - 25,4 mm (ø 3/16 - 1“). Presser les boutons de pression sur les deux côtés et mettre ou ôter la barre de fermeture.
Tourner la barre der fermeture selon le ø.
Mettre ou ôter la barre de fermeture. ø 28,5 - 38 mm (ø 1 1/8 - 1 1/2“). Presser les boutons de pression sur les deux côtés et mettre ou ôter la barre de fermeture.
Ajustage de la butée du papier selon le format du papier. Desserrer la vis de serrage à l‘arrière, mettre la butte du papier et resserrer la vis de serrage.
VORBEREITEN \ PREPARE \ PREPARACIÓN \ PRÉPARATION
Bindeelement in die Haltevorrichtung schieben. Haltevorrichtung hält das Bindeelement fest, wenn gestanztes Papier eingekämmt wird.
Verschluß der Drahtkammbindung soll innen liegen. Kammverschluß muß innen liegen.
Buchblock aufstellen Heftrücken nach oben. Rückseite nach vorn klappen. Deckblatt und Rückseite liegen jetzt hintereinander.
Buchblock drehen. Deckblatt und Rückseite liegen unten. Seiten von oben abnehmen.
Push binding element in the holding fixture. Holding fixture holds binding element during insertion of the punched paper.
The seam of the closed binding element should be inside the book. Not outside the covers.
Set the book upright, binding side to the top, place the back cover in front. The front cover should be behind the back cover.
Turn the book over, covers are underneath. Take pages from the top.
Colocar el encuadernador en el dispositivo de retención. Esta mantendra sujeta el encuadernador para introducir al papel perforado.
El cierre del encuadernador debe quedar por dentro y no por fuera de las cubiertas.
Colocar el bloque con la parte a taladrar hacia arriba, con la contraportada al principio. La portada debe estar detrás de lacontraportada.
Colocar el bloque a encuadernar con las cubiertas hacia abajo. Tome las hojas por arriba
Pousser la réglette de reliure sous la réglette de serrage. La réglette de serrage maintient l’élément de reliure quand le papier perforé est introduit dans le peigne.
La fermeture de la reliure en fil doit se trouver à l’intérieur. La fermeture à peigne doit se trouver à l’intérieur.
Répartir le livre non relié. Faire butter les feuilles vers le haut. Rabattre la couverture vers l’avant. Couverture et dos se trouvent maintenant l’un derrière l’autre.
Retourner le livre non relié. Couverture et dos se trouvent au-dessous. Retirer les feuilles par le haut.
Page 4 of 8

Text on page 5
STANZEN \ PUNCH \ PERFORACIÓN \ PERFORATION
max. 22 Seiten (80 g/m) dicke Buchblocks in Lagen stanzen. Empfohlene Stanzstärke 15 - 20 Blatt. Plastik und dickere Deckblätter nur einzeln stanzen.
Papierlage in Stanzschacht einführen und am Anschlag anstellen. Papier muß plan stehen, evtl. noch einmal ausrichten.
Stanzhebel nach vorn bis zum Anschlag drücken und wieder ganz zurückführen. Maschine mit der anderen Hand halten.
Punch max. 22 pages 80 g/m. Recomended punching: 15 - 20 pages. Punch plastics and thicker covers separately.
Insert paper into punching slot, slide the paper against the paper guide. Paper must stand evenly, if not align it again.
Press punching lever forward until it stops, then return to original position. Hold the machine with the other hand.
Max. capacidad de perforación: 22 hojas de 80 g/m² Es aconsejable perforar 15 - 20 hojas cada vez. Perforar elplastico y tapas gruesas separadamente.
Introduzca el bloque de papel en la cavidad de perforado y lévelo al tope El papel debe estar plano y debe alinearse de nuevo si fuera preciso
Presionar la palanca de perforar hacia delante hasta el fin y devuélvala del todo hacia atrás. Sujete la máquina con la otra mano.
Perforer des livres non reliés par paquets d’un maximum de 22 feuilles (80 g/m). Ne perforer les couvertures en plastique et plus épaisses qu’à l’unité.
Introduire les paquets de papier dans le puits de perforation et mettre en place la butée. Le papier doit être à plat. Régler à nouveau éventuellment.
Appuyer sur le levier de perforation vers l’avant jusqu’à ce qu’il bute et ramener à fond en arrière. Maintenir la machine avec l’autre main.
EINKÄMMEN \ INSERT \ INTRODUCCIÓN \ INTRODUCTION
Gestanztes Papier beidhändig entnehmen,
gleich in das Bindeelement einkämmen.
Bei dickeren Buchblocks Schritte 5 und 6 wiederholen, bis alle Seiten gestanzt sind.
Remove punched paper from the punching slot.
Insert paper onto the binding element.
For thicker books, repeat steps 5 and 6 until all pages are punched.
Tome el papel perforado con ambas manos
e introdúzcalo en el elemento de encuadernación
Para bloques de hojas de mayor grosor, repita las operaciones 5 y 6 hasta que todas las hojas estén perforadas.
Enlever le papier perforé avec les deux mains.
Introduire immédiatement dans les peignes de l’élément de reliure.
Pour les livres non reliés épais, recommencer les opérations 5 et 6 jusqu’à ce que toutes les feuilles soient perforées.
Page 5 of 8

Text on page 6
ANLEGEN \ ADJUST \ COLOCACIÓN \ MISE EN PLACE
Bindeelement von der Halteleiste herausheben, mit Buchblock entnehmen Papier so anfassen, daß es nicht aus dem Bindeelement rutscht.
Bindeelement unter den Schließbalken schieben.
Bindeelement muß senkrecht an der Rückwand des Schließbalkens stehen. Öffnung des Bindeelements zeigt zur Rückwand.
Bindehebel bis zum Anschlag nach vorn drücken und wieder zurückführen. Bei größerem Bindedurchmesser mehr Kraft einsetzen.
After the paper has been placed on the binding element, remove the paper with the element from the holding fixture. Hold the paper that it does not slide out of the binding element.
Put binding element under the closing bar.
Binding element must stand vertically at the back of the closing bar with opening of the binding element to the back.
Press binding lever forward until it stops and back again. For bigger diameters use more force.
Levante el elemento de encuadernación debajo del dispositivo y sáquelo con él bloque. Tome con las manos el papel de modo que no se deslice fuera del elemento de encuadernación.
Deslice el elemento de encuadernación debajo de la barra de cierre.
El elemento de encuadernación debe estar perpendicular respecto a la barra de cierre. La abertura del elemento de encuadernación mira hacia la cubierta posterior
Presione la palanca de encuadenación hacia delante hasta el tope y devuélvala hacia atrás. A mayor diámetro de encuadernación, mayor fuerza se necesita
Soulever l’élément de reliure sous la dispositif de serrage, l’enlever avec le livre non relié. Saisir le papier de façon telle qu’il ne glisse pas de l’élément de reliure.
Pousser l’élément de reliure sous la barre de fermeture.
L’élément de reliure doit se trouver verticalement contre la paroi arrière de la barre de fermeture. L’ouverture de l’élément de reliure est dirigé vers la paroi arrière.
Appuyer sur le levier de reliure jusqu’à ce qu’il butte et le ramener. Pour les gros diamètres de reliure, recourir à plusieurs opérations.
SCHLIESSEN \ CLOSE \ CIERRE \ FERMETURE
Bindung zu offen: Schließbalken etwas tiefer einstellen. Klemmschraube lösen und etwas nach links schieben. Klemmschraube festziehen. Bindehebel noch einmal drücken.
Bindung zu eng: Schließbalken etwas höher einstellen. Klemmschraube lösen und etwas nach rechts schieben, Klemmschraube festziehen. Nächstes Exemplar richtig schließen.
Binding under closed: Adjust closing bar a little deeper. Release attachment screw and move it slightly to the left. Fix attachment screw. Press binding lever again.
Binding over closed: Adjust closing bar a little higher. Release attachment screw and move it slightly to the right. Fix attachment screw. Close next book.
Unión demasiado abierta: ajuste la barra de cierre algo más abajo. Afloje el tornillo de sujeción desplázandolo un poco hacia la izquierda. Apriételo. Presione de nuevo la palanca de encuadernación.
Unión demasiado estrecha. Ajuste algo más alta la barra de cierre. Afloje el tornillo de sujeción desplázandolo un poco hacia la derecha. Apriételo. Cierre correctamente el siguiente ejemplar.
Reliure trop ouverte: régler la barre de fermeture un peu plus profond. Desserrer la vis de serrage et pousser un peu vers la gauche. Serrer la vis de serrage appuyer à nouveau sur le levier de reliure.
Reliure trop serrée: régler la barre de fermeture un peu plus haut. Desserrer la vis de serrage et pousser un peu vers la droite. Serrer la vis de serrage. L’exemplaire suivant fermera convenablement.
Page 6 of 8

Text on page 7
WARTEN \ MAINTENANCE \ LIMPIEZA \ ENTRETIEN
Nur trocken reinigen. Mit trockenem oder feuchtem Tuch abwischen. Keine Lösungsmittel verwenden, Aufdrucke können sich lösen.
Schublade regelmäßig leeren. Schublade herausziehen und Papierabfall ausschütten.
Cleaning Wipe with a dry or moist cloth. Do not use solvents, sticker may detach.
Empty drawer from time to time. Pull out drawer and empty out the papershavings.
Limpieza sólo en seco. Limpie con un paño seco o humedecido. No utilice disolventes. Las huellas se pueden borrar.
Vaciar la bandeja del desperdicio del papel periodicamente.
Ne nettoyer qu’à sec. Essuyer avec un chiffon sec ou humide. Ne pas utiliser de solvant. Les empreintes peuvent s’effacer.
Vider le tiroir régulièrement. Sortir le tiroir et jeter les rognures de papier.
TECHNISCHE DETAILS \ TECHNICAL DATA \ DATOS TECNICOS \ DONNEES TECHNIQUES
Länge x Breite x Höhe 58 x 33 x 15 cm
Length x Width x Height 58 x 33 x 15 cm / (22,8 x 13 x 5,9“)
Longitud x Ancho x Altura 58 x 33 x 15 cm
Longueur, largeur, hauteur 58 x 33 x 15 cm
Gewicht 15,5 kg
Weight 15,5 kg / 34,10 lbs.
Peso 15,5 kg
Poids 15,5 kg
Stanzstempel einzeln ausschaltbar ja (alle)
Disengageable punch pins yes (all)
Punzones desembragables sí (todos)
Poinçons de perf. débrayables oui (tous)
Stanzstärke bis zu 2,2 mm / 22 Blatt*
Punching thickness up to 2,2 mm / 22 sheets*
Espesor de perforación hasta 2,2 mm / 22 hojas*
Epaisseur de perforation jusqu‘à 2,2 mm / 22 feuilles *
verstellbarer Randabstand ja
Adjustable margin control yes
Distancía al margen variable sí
Marge de perforation réglable oui
max. Blockstärke 13,5 mm / 135 Blatt
Max. binding thickness 13,5 mm (9/16“) / 135 sheets*
Espesor máx. del bloque hasta 13,5 mm / 135 hojas*
Capacité de reliure jusqu‘à 13,5 mm / 135 feuilles*
verarbeitbare ø 3/16“ - 5/8“ (5,5 - 16,0 mm)
ø of the wire elements 3/16“ - 5/8““ (5,5 - 16,0 mm)
ø mecanizables 3/16“ - 5/8“ (5,5 - 16,0 mm)
ø des éléments métalliques 3/16“ - 5/8“ (5,5 - 16,0 mm)
max. Bindebreite bis zu 360 mm
Max. binding width up to 360 mm (14,2“)
Ancho máx. de encuadernación hasta 360 mm máx.
Largeur de travail jusqu‘à 360 mm máxi.
Number of punch pins
Schlaufenanzahl/Loops auf DIN A4 Schlaufenanzahl/Loops auf DIN A5
Number of loops A4 size 34 loops (11“ size 32 loops) A5 size 24 loops (8,5“ size 25 loops)
Número de anillas/loops en DIN A4 Número de anillas/loops en DIN A5
Boucles pour format A4 Boucles pour format A5
Page 7 of 8

Text on page 8
TEILUNG \ PITCH \ PASO \ PAS
3/16“ 5,5 mm
1/4“ 6,9 mm
5/16“ 8,0 mm
3/8“ 9,5 mm
7/16“ 11,0 mm
1/2“ 12,7 mm
9/16“ 14,3 mm
5/8“ 16,0 mm
Bindelänge Binding length Longitud de encuadernación Longuer à relier
Loops Loops Anillas Anneaux
Bestell Nr. / Order Nr. 971000061 Stand / as per 02 / 2009
Bindelänge Binding length Longitud de encuadernación Longuer à relier
Loops Loops Anillas Anneaux
für ca. Blätter* maximum sheets* No. aprox. de hojas* No. approx. de feuilles*
Ø mm
Zoll Inch Pulgadas Pouce
- 70-80 g/m² / 20# stock
Page 8 of 8 ยท End of manual
Quick start
- Unpack: lift the machine out of the box without using the binding lever (weight 15.5 kg / 34.10 lbs.) and place it on a solid, fully supported surface. Shelves are not recommended.
- Clean the punch dies: before first use, punch scrap paper to remove the rust preventative from the punch dies.
- Set the diameter: lay the book against the measuring scale to read the element diameter (e.g. 3/8"), set the scale to it, and turn the margin knob to the same diameter.
- Set the paper size: for A4 (34 loops) pull the 35th pin, for 11" paper (32 loops) pull the 33th pin. Loosen the screw at the rear, slide the paper guide to your size and tighten it.
- Punch: insert up to 22 pages 80 g/m into the punching slot against the paper guide, then press the punching lever forward until it stops and return it. Hold the machine with your other hand.
- Insert the pages: push the binding element into the holding fixture with the book prepared so the seam ends up inside, then put the punched paper onto it.
- Close: lift the book and element out, slide the element under the closing bar standing upright with its opening to the back, and press the binding lever forward until it stops, then back.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Binding is under closed (too open) | Closing bar set too high | Release the attachment screw, move it slightly to the left to set the closing bar a little deeper, fix the screw, and press the binding lever again. Page 6 |
| Binding is over closed (too tight) | Closing bar set too low | Release the attachment screw, move it slightly to the right to set the closing bar a little higher, and fix the screw before closing the next book. Page 6 |
| Punched holes show stains on first use | Rust preventative on the punch dies | Punch scrap paper until the holes come out clean. Page 2 |
| Holes are crooked or uneven | Paper not standing evenly in the punching slot | Align the paper again so it stands evenly against the paper guide before punching. Page 5 |
| Book is too thick to punch in one pass | More than max. 22 pages 80 g/m | Punch thick books in sections of 15 to 20 pages, and punch plastics and thicker covers separately. Page 5 |
| Element seam shows outside the covers | Book not prepared with the back cover in front | Set the book upright, binding side up, with the back cover in front before inserting the pages. Page 4 |
| Paper shavings build up in the waste drawer | Drawer not emptied | Pull out the drawer and empty the paper shavings from time to time. Page 7 |
Frequently asked questions
How much can the SRW 360 punch at once?
Up to 22 pages 70/80 g/m (20 # stock), up to 2.2 mm. Card stock up to 1.5 mm thick, and plastic foil 1 page of 0.3 mm. The recommended amount is 15 to 20 pages. Do not punch other materials or metal. See page 2, page 5, page 7.
What wire sizes and book thickness does it handle?
Wire elements from 3/16" to 5/8" (5.5 to 16.0 mm), with a max. binding thickness of 13.5 mm (9/16"), about 135 sheets. See page 7, page 8.
How wide a document can it punch and bind?
The max. binding width is up to 360 mm (14.2"). An A4 sheet takes 34 loops (11" size 32 loops) and A5 takes 24 loops (8.5" size 25 loops). All punch pins can be disengaged. See page 3, page 7.
What are the size and weight?
58 x 33 x 15 cm (22.8 x 13 x 5.9") and 15.5 kg / 34.10 lbs. See page 7.
How do I maintain it?
Wipe it with a dry or moist cloth, without solvents, since stickers may detach. Empty the waste drawer from time to time. See page 7.
