Rhin-O-Tuff HD4102 Manual, page 1
Text on page 1

HD-4101Book Former and HD-e4100 Coil Inserter

“HD-4102 Docking Kit” Instruction Sheet

For 11” to 14” binding edges.

www.RHIN-O-TUFF.com

Initial Setup:

Shown in Figure A: Insert the HD-4102 Docking Kit mount pins (1) into the two holes in the front bar of the HD-e4100 Coil Inserter until completely down and flush.

Shown in Figure B: Attach the Clips (2) to the HD- 4101 Book Former with supplied screws using supplied Allen wrench.

HD-4102 Docking Kit

Shown in Figure C: Mount the HD-4101 Book Former to the “HD-4102 Docking Kit”.

Operation:

See Figure D & E: When Coiling 32MM and above, set the Small Roller (3) to the lower position and the Clips (4) to the Bottom position. With 32MM and below, use the Small Roller (3) middle position and the Clip (4) Top position. With the book loaded and coil started, rotate the HD-4101 Book Former (6) upward while holding the book in place (5). The setup is correct when your coil engages both the lower roller and larger roller almost simultaneously (7). These are general rules for coiling. When you have become comfortable with the system, alternate setups work well also.

Hint: While learning to coil with the larger sizes of coil, using a simple trick will speed up your job. Use the size coil you’re binding, cut a piece into a half circle (½ coil). When you enter your binding coil into the first 4 holes, also put the ½ coil into the last hole. This aligns the book much better and must be removed just as the binding coil enters the last hole.

Page 1 of 1 · End of manual

Quick start

  1. Mount the pins: Insert the HD-4102 Docking Kit mount pins into the two holes in the front bar of the HD-e4100 Coil Inserter, until completely down and flush.
  2. Attach the clips: Fix the Clips to the HD-4101 Book Former with the supplied screws and Allen wrench.
  3. Dock the former: Mount the HD-4101 Book Former on the HD-4102 Docking Kit.
  4. Set the rollers: For coil 32MM and above, put the Small Roller low and the Clips at Bottom. For 32MM and below, use the middle roller and Top clip position.
  5. Start the coil: Load the book and start the coil. Rotate the book former upward while you hold the book in place.
  6. Check engagement: The coil should engage the lower roller and larger roller almost at the same time.

Troubleshooting

ProblemLikely causeFix (from the manual)
Docking kit does not sit right on the inserterMount pins are not seated.Push the HD-4102 pins fully down, flush in the two front bar holes. Page 1
Coil does not engage both rollers togetherRoller and clip positions do not fit the coil size.Use Small Roller lower and Clips Bottom for 32MM and above. Use middle and Top for 32MM and below. Page 1
Book lines up poorly at the last hole with large coilThe book is not aligned near the last hole.Cut a piece of the same coil into a half circle and put it in the last hole while the first 4 holes are coiled. Remove it as the coil enters the last hole. Page 1
Book former wobbles on the docking kitThe clips are not firmly attached.Attach the clips to the HD-4101 with the supplied screws and Allen wrench. Page 1

Frequently asked questions

What binding edge size does the HD-4102 Docking Kit cover?

It is for 11 inch to 14 inch binding edges. See page 1.

What does the HD-4102 attach to?

It joins the HD-4101 Book Former to the HD-e4100 Coil Inserter. See page 1.

How do I set the small roller for 32MM coil?

For 32MM and above, set the Small Roller lower and clips Bottom. Below 32MM, use the middle roller and Top clip. See page 1.

What is the half coil trick on the HD-4102?

Cut a piece of your coil into a half circle and place it in the last hole while starting the coil. Remove it just as the coil reaches the last hole. See page 1.