Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 1

Page 1 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 2

Page 2 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 3
Text on page 3

OD4012, OD4000 and OD4800 Setup & Operator Manual

Issue 3 June 09 Performance Design LLC.

These punches have been designed to punch most any job that may pass through your office. No matter what type of binding you need to carry out, these punches can handle the job. The maximum single punching length for the OD4012, OD4000 and OD4800 is a 11” (297mm) format. The OD4012 and the OD4000 are electrically operated punches and the OD4800 is manually operated. All three machines utilize a simple two knob die lock system to retain the die punch assemblies.

OD4012

OD4000

OD4800

Page 3 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 4
Text on page 4

OD4012 Contents S/N:____________

___Punch (1) ___Oil (1) ___Foot Pedal (1) ___Reversing Tool (1)

___Instruction Book (1) ___Brush (1) ___Power Cord (1)

OD4000 Contents S/N:____________

___Punch (1) ___Knob Kit (1)

  1. ¼-20 x 1 ½” Knob (2) ___Foot Pedal (1)

___Instruction Book (1) ___Oil (1) ___Brush (1) ___Power Cord (1)

OD4800 Contents S/N:____________

___Punch (1) ___Knob Kit (1)

  1. ¼-20 x 1 ½” Knob (2) ___Brush (1)

___Instruction Book (1) ___Handle with bolt (1) ___Oil (1)

Page 4 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 5

Page 5 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 6
Text on page 6

Table of Contents

Topic:

Page Number:

Die installation / Maintenance

Setting the paper stop/guide

Page 6 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 7
Text on page 7

Safety Alert Symbols

Make sure you read this section very carefully! Learn to recognize these Safety Alert Symbols. The OD4012, OD4000 and OD4800 have been designed to provide a high level of protection to an operator. Follow the guidelines below while installing, operating and maintaining your machine.

! CAUTION

CAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. It may also be used without the safety alert symbol as an alternative to "Notice".

! WARNING

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

! DANGER

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.

Safe Operating Guidelines

Always keep this instruction manual with the machine for reference to safe operating guidelines and correct operation of the machine.

The OD4012 and OD4000 need to be plugged into a wall outlet that provides a 15-amp, 120 volt service (16-amp, 220 volt for European installations) and is protected by a fuse or circuit breaker at the main electrical panel.

Always replace any fuse with the same type and amperage fuse as indicated on the machine.

If machine cycles on its own, turn off power switch, unplug machine from the wall outlet and call your dealer immediately for service.

! WARNING

Hazardous voltage inside. Disconnect power before servicing.

Page 7 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 8
Text on page 8

Turn power switch off before maintaining or changing die assembly.

! WARNING

Keep hands away from moving parts.

Lockout and disconnect power before servicing.

Use of appropriate hand protection should be utilized to avoid injury from handling of materials.

! CAUTION

Injury to fingers and hands.

Follow all recommended workplace procedures for repetitive activities.

Placing your machine in the proper location:

Before lifting machine, turn power off and remove the power cord from the wall outlet. The machine is very heavy! Never attempt to lift the machine by yourself. Two people will be needed to lift the machine.

! CAUTION

Single person lift could result in injury.

Two person lift required.

Place the machine on a hard level surface, place the foot pedal on the floor in front of the machine. Ensure the placement of machine allows for ergonomic work flow (separate locations for un-punched books and punched books).

! CAUTION

u Connect the foot-pedal into the foot-pedal Tripping Hazard receptacle on the back of the machine, do not Bodily injury could occur from fall. attempt to connect foot-pedal into anything other than the foot-pedal receptacle. u Optional paper activated switches are available for these punches. These switches replace the foot-pedal and plug into the foot-pedal receptacle on the back of the machine.

Route cables away from walkways

Page 8 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 9
Text on page 9

Attach Handle to OD4800:

The OD4800 manual punch is shipped with the handle removed from the punch. You will need two 3/8” wrenches (not supplied) to tighten the handle bolt. ? Locate the handle and remove the nut, washer and bolt from the handle.  Orientate the handle so the black handle grip extends to the right of the machine as seen on front cover of this book. ? Slide handle onto exposed crankshaft of machine and align the holes in the handle with the hole in the crankshaft.  Insert the bolt completely through the handle and install the washer and nylock nut. See photo below left.  Tighten the nut securely so there is not play between the handle and the crankshaft. ? Open the top grey lid of the punch and remove the styrofoam block. See photo below right.

Front of Machine

Diagram 1 (Image of OD4800)

Page 9 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 10
Text on page 10

Providing power to the machine:

Power cord shall be certified for the country where the machine will be installed. Plug one end of the power cord into the power cord receptacle on the back of the machine. The other end goes into the wall outlet.

! DANGER

Use only approved power cord assemblies.

Die Installation:

OD4012 Diagram 2. Make sure the machine ! WARNING is turned off before installing the die . Crush hazard. Keep hands away u Make sure there is no paper dust or paper chips from moving parts. in the machine die slot before installing the die. u Install the die by sliding it into the opening located on the left hand side of the machine. Make sure the punch pin retainer slides into the slot on the backside of the opening. u Install die until right side of die is flush to exterior of right side of machine. u Thread both retained die lock knobs into the die and tighten evenly until the die can not move.

Lockout and disconnect power before servicing.

Punch Pin Retainer

Diagram 2. (Image of OD4012)

Page 10 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 11
Text on page 11

OD4000/OD4800: Diagram 3. Make sure the ! WARNING Crush hazard. machine is turned off before installing the Keep hands away die. from moving parts. u Make sure there is no paper dust or paper chips in the machine die slot before installing the die. u Install the die by sliding it into the opening of the machine located on the left hand side of the machine. Make sure the punch pin retainer slides into the slot of the pusher bar. u Install die until right side of die is flush to exterior of right side of machine. u Locate the two supplied die lock knobs and insert them into the left and right sides of the machine. Thread both die lock knobs into die assembly and tighten evenly until die assembly can not move.

Lockout and disconnect power before servicing.

Punch Pin Retainer

Diagram 3. (Image of OD4000)

Comb Die Backspace (Margin) Adjustment

The comb die assemblies for the OD4012, OD4000, and OD4800 have a four position adjustable backspace. The positions are changed by pulling the adjustor bar to the left for deeper settings (commonly used for average to thicker sized books) and pushing the adjustor bar to the right for shallower settings (commonly used for thinner sized books).

Page 11 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 12
Text on page 12

Turn machine power off and remove die assembly from the machine.

On the opposite side of the die assembly from the die handle, push

Pull the pin capture away from the pin retainer to expose the punch pins.

Remove the desired punch pin or pins.

Replace the pin capture by pressing down on the pin retainer and placing the pin capture back into place.

Install die assembly into machine as described earlier and turn machine power back on.

Die maintenance should be performed with the die removed from the machine. To perform the die maintenance, remove the die assembly from the machine (see die installation section). Apply enough oil to lightly coat each pin. u Remove any excess oil with a disposable cloth. After oiling, always punch some scrap paper to remove excess oil.

Saturate a small section of a cloth with oil and using that portion of the cloth, wipe the punch pins to apply a light coating of oil.

Page 12 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 13
Text on page 13

Setting the paper stop/guide:

OD4012, OD4000 and OD4800 u Locate the paper stop on the front cover of the machine. Loosen the knob counterclockwise, so that the guide can be adjusted to the left or the right. Move the paper stop until the desired position is reached and tighten the knob clockwise until tight to lock the paper stop in place. Repeat this procedure until the punch pattern is centered on the paper.

The OD4012, OD4000 and OD4800 punch machines allow for viewing of Paper Stop the common size paper position markings on the die assemblies. Aligning the paper stop with these marks will result in the punch pattern being centered on the paper and need only small adjustments if at all.

Punching Paper:

Select an appropriate number of sheets to be punched and slide the sheets down vertically into the opening of the die assembly. When the paper is fully inserted, slide it to the left so it comes in contact with the paper stop. Make sure all the edges of the sheets are flush by tapping the top and the right hand sides of the sheets then activate the punch by depressing the foot-pedal. OD4800 users pull handle toward front of machine.

If a paper activated switch is being used, tap the sheets flush before sliding the paper to the paper stop.

Removing Paper Waste:

The paper waste drawer is located conveniently on the front of the punch. The paper waste drawer is removed by lifting up on the front and pulling out away from the machine. This drawer should be checked frequently while punching and emptied as necessary.

Page 13 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 14
Text on page 14

Paper Jam:

The OD4012 and OD4000 punches use a circuit board for controlling the punch cycle, this circuit board also has the ability to automatically reverse the pusher bar and punch pins to their starting position if the machine takes too much time to complete a punch cycle. This condition could happen if too much material has been attempted to be punched at one time. If this condition occurs, allow the machine to attempt to reset itself back to its home position.

Turn the machine power switch off and remove some or all of the material in the punch.

! WARNING

Keep hands away from moving parts.

Lockout and disconnect power before servicing.

It is easier to remove one or two sheets at a time from the backside of the material in the punch.

If the punch does not reset itself back to its home position, the punch will need to be reversed manually.

OD4012 Manual Reverse utilizes a reversing tool supplied with the punch. Turn the

machine power switch off and unplug the power cord from the wall. Locate the

! WARNING

Keep hands away from moving parts.

Lockout and disconnect power before servicing.

silver plug on the rear of the left side panel of the machine. Remove the silver plug by prying it out gently with a small flat tool. Insert the end of the reversing tool into the open hole and engage the tool with the end of the motor shaft. Rotate the tool counterclockwise 5-10 revolutions, until the punch pins have been retracted back to the starting position. Remove most or all of the material from the punch. Remove the reversing tool from the punch and replace the small silver plug. Plug the power cord back into the wall outlet and turn the power switch on. Test cycle the machine by punching with no material in the punch, the machine will reset itself back to its home position. Reduce the amount of material being punched and continue working.

Page 14 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 15
Text on page 15

OD4000 Manual Reverse Turn the machine

power switch off and unplug the power cord from the wall. Locate the silver plug

! WARNING

Keep hands away from moving parts.

Lockout and disconnect power before servicing.

on the rear of the left side panel of the machine. Remove the silver plug by prying it out gently with a small flat tool. Insert the end of a large flat blade screwdriver into the open hole and engage with the end of the motor shaft. Rotate the screwdriver counterclockwise 5-10 revolutions, until the punch pins have been retracted back to the starting position. Remove most or all of the material from the punch. Remove the screwdriver from the punch and replace the small silver plug. Plug the power cord back into the wall outlet and turn the power switch on. Test cycle the machine by punching with no material in the punch, the machine will reset itself back to its home position. Reduce the amount of material being punched and continue working.

It is easier to remove one or two sheets at a time from the backside of the material in the punch.

Page 15 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 16
Text on page 16

! DANGER

Only qualified personnel should attempt to work on this equipment. There are no user serviceable parts inside of the machine.

Hazardous voltage inside. Disconnect power before servicing.

Your machine has been designed for years of trouble free operation. The following is a troubleshooting guide to help you through some of the problems that may be encountered.

Troubleshooting

Possible Cause

Action

Machine does not cycle

1) Machine is off

2) Machine is not plugged in

3) Foot-pedal is not plugged into machine

4) Die lock handle is not locked

5) Reversing tool is in machine

1) Check power switch

2) Check both ends of power cord

3) Make sure foot-pedal cable is attached to machine.

4) Lock the die lock handle

5) Remove reversing tool and store properly

Die does not go into machine

1) Pin retainer interference

2) Punch is stopped in mid cycle

3) Die lock handle is in lock position

1) Make sure pin retainer enters slot in pusher-bar.

2) Restart machine by turning power off and back on

3) Move handle to unlock position

Symptom

NOTICE The OD4012 and OD4000 have been tested with a

duty cycle of 25 cycles per minute with a 1 minute rest period after 2 minutes of run time. Operating outside of these limits could result in machine damage.

The OD4012 has earned the UL Listing Mark. E179574.

Page 16 of 17

Rhino 4012PC Medium Duty Electric ProClick Punch System Manual, page 17
Text on page 17

! IMPORTANT

Be sure to fill out and return your Product Warranty Registration Card or Register online at: www.Rhin-O-Tuff.com/warranty_registration.asp

Part Number 001172 Rev. 3 Aug 2010

Page 17 of 17 ยท End of manual

Quick start

  1. Place the punch: with two people, set the machine on a hard level surface and put the foot pedal on the floor in front of it. Route cables away from walkways.
  2. Connect: plug the foot pedal into the foot-pedal receptacle on the back, then plug the power cord into the machine and into a wall outlet with 15-amp, 120 volt service.
  3. Install the die: with the power off, clear any paper chips from the die slot, slide the die in from the left side with the punch pin retainer in its slot, and push it flush with the right side. Tighten both die lock knobs evenly.
  4. Set the margin: pull the adjustor bar to the left for deeper backspace on thicker books, or push it to the right for shallower settings on thinner books.
  5. Set the paper stop: loosen the knob, line the paper stop up with the paper size marks on the die, and tighten it so the punch pattern is centered.
  6. Punch: slide the sheets down into the die opening, slide them left against the paper stop, tap the top and right edges flush, then press the foot pedal.
  7. Empty waste: check the paper waste drawer on the front often. Lift up on the front and pull it out to empty it.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not cycleMachine is off, not plugged in, or the foot pedal is not plugged inCheck the power switch, both ends of the power cord, and that the foot-pedal cable is attached to the machine. Page 16
Machine does not cycleDie lock handle not locked, or reversing tool left in the machineLock the die lock handle, and remove the reversing tool and store it properly. Page 16
Die does not go into the machinePin retainer interference, punch stopped mid cycle, or die lock handle in lock positionMake sure the pin retainer enters the slot in the pusher-bar, restart the machine by turning power off and back on, and move the handle to the unlock position. Page 16
Punch reverses itself during a cycleToo much material punched at one timeLet the machine reset to its home position, turn the power off, and remove some of the material, one or two sheets at a time from the backside. Page 14
Punch jams and does not reset to homeToo much material in the punchTurn off and unplug the machine, remove the silver plug on the rear of the left side panel, and turn the reversing tool counterclockwise 5-10 revolutions until the pins retract. Replace the plug and test cycle with no paper. Page 14
Machine cycles on its ownMachine faultTurn off the power switch, unplug the machine from the wall outlet and call your dealer immediately for service. Page 7
Oil marks on punched sheets after die maintenanceExcess oil on the punch pinsWipe off excess oil with a disposable cloth and punch some scrap paper. Page 12

Frequently asked questions

What is included with the OD4012?

The punch, oil, a foot pedal, a reversing tool, the instruction book, a brush and a power cord. See page 4.

How long a sheet can it punch?

The maximum single punching length is an 11" (297mm) format. See page 3.

What is the duty cycle?

The OD4012 was tested with a duty cycle of 25 cycles per minute with a 1 minute rest period after 2 minutes of run time. Operating outside these limits could damage the machine. See page 16.

What power does it need?

A wall outlet with a 15-amp, 120 volt service (16-amp, 220 volt for European installations), protected by a fuse or circuit breaker. See page 7.

Can I use it without the foot pedal?

Yes. Optional paper activated switches replace the foot pedal and plug into the foot-pedal receptacle on the back. See page 8.

How do I maintain the dies?

Remove the die from the machine, wipe the punch pins with an oil-saturated cloth to apply a light coat, wipe off any excess, and punch some scrap paper. See page 12.