RhinoTuff 3250CL Manual, page 1

Page 1 of 11

RhinoTuff 3250CL Manual, page 2
Text on page 2

Pro Series 3250CL

Features: 11” Punching Edge 25 Sheet Capacity** Book Former Easy to Use Coiler 3-Year Limited Warranty

Page 2 of 11

RhinoTuff 3250CL Manual, page 3
Text on page 3

Features

Roller Start

Roller Button

Page 3 of 11

RhinoTuff 3250CL Manual, page 4
Text on page 4

Capabilities & Specifications

Important Safety Notice

  • Always replace fuses or circuit breakers with the correct amperage and type.
  • Never bypass safety devices.
  • Hazardous voltages inside of machine.
  • No user serviceable parts inside of machine. Machine should only

be opened by qualified repair personnel.

Max Coil Size Recommended

4:1 .2475" spacing [.172" dia.]

2 Min. Run / 1 Min Rest

Shipping weight / Machine weight

Page 4 of 11

RhinoTuff 3250CL Manual, page 5
Text on page 5

Setup

Back of Machine

Power Cord

  • Position machine on solid surface
  • Plug power cord into wall outlet

Unpackage machine

On-Off Switch

Turn power switch on

Punch

  • Insert paper, slide left, press punch button
  • Punch no more than 25 sheets of paper at one time
  • Punch no more than 2 sheets of plastic at one time

Prepare book to be coiled by placing the Front Cover on top and the Back Cover on the bottom of the Book Body

Page 5 of 11

RhinoTuff 3250CL Manual, page 6
Text on page 6

Coil

Determine the coil size needed by mm s 15 heet measuring the book thickness s with guide on right side of the mm s 12 heet s accessory tray. mm s Move book from larger to smaller 10 heet s sizes until book just fits between m 8m heets s guides. m 6m eets The number associated with the h s slot (i.e. 8mm) signifies what size of coil to use.

mm s 15 heet s

mm s 12 heet s mm s 10 heet s m

8m heets

s m 6m eets h s

Identify the size of coil by sliding coils over the circular pegs starting from small to large. Use the coil that fits on the peg found by measuring the book thickness in previous step.

Page 6 of 11

RhinoTuff 3250CL Manual, page 7
Text on page 7

Coil

  • Manually start Coil into the first 3-4 holes on right hand side of book
  • Press Coil Button to start roller spinning
  • Gently bring the coil into contact with the front side of the spinning roller while holding the book in a horizontal plane as shown above
  • Allow coil to spin into the book

Crimping

  • Position pliers with the RED dot facing up, to the ceiling as shown
  • Holding pliers horizontally, insert the plier tips around the last coil of the book on the right hand side of the book
  • Close pliers completely; this will cut and crimp the coil

Page 7 of 11

RhinoTuff 3250CL Manual, page 8
Text on page 8

Crimping

Flip the entire book over so that the back cover is now on top

  • Position pliers with the RED dot facing up, to the ceiling as shown
  • Holding pliers horizontally, insert the plier tips around the last coil of the book on the right hand side of the book
  • Close pliers completely; this will cut and crimp the coil

Page 8 of 11

RhinoTuff 3250CL Manual, page 9
Text on page 9

Troubleshooting

Symptom

Solution

Machine will not punch holes in paper

  • Plug power cord into wall outlet
  • Check wall outlet has power
  • Switch machine power switch to the “on” position

Holes punch on the edge of paper

  • Clear paper chips from the throat of the punch die
  • Seat paper completely into the bottom of the punch die

Holes punch off center of page

  • Move paper to the left, against the paper stop, prior to pressing the punch button

Punch will not punch through completely

  • Remove a couple of sheets from the back side of the lift of paper and press the punch button again
  • Only punch 25 sheets of 20lb copy paper at one time and only 2 sheets of plastic at one time

Punch has stopped with punch pins still in the paper and will not retract on its own

  • Turn machine power switch to the “off” position and unplug power cord from the wall.

Remove the black cap from the right side plate of the machine. Use a flat blade, standard screwdriver to rotate the shaft counter-clockwise. This will manually retract the punch pins from the paper, continue until all pins have retracted completely.

Page 9 of 11

RhinoTuff 3250CL Manual, page 10
Text on page 10

Troubleshooting

Symptom

Solution

Coil will not spin into book

  • Align pages of book such that the holes in the pages are all evenly aligned
  • Use book former to shape book to the contour of the coil

Pliers will not crimp coil

  • Make sure that the RED dot is pointing up, to the ceiling and the right hand side of the book is being cut/crimped
  • Hold pliers horizontally
  • Grasp coil being cut firmly between thumb and forefinger will operating pliers

Warranty

The 3250CL coil binding system is covered by a 3 Year Limited Warranty against defects in materials and workmanship, and is limited to the replacement of the defective system or the repair of the defective system at the manufacturing facility. Modifications or intentional abuse of the system will not be covered under this warranty. The punching die assembly will be covered for 1 year to be free of manufacture defects.

To obtain warranty repair of 3250CL coil binding system:

  1. Obtain serial number of machine from decal on back of machine as shown below.
  2. Call 1-800-390-5782 to arrange for a Return Merchandise Authorization number. Please have the symptom(s) of the machine failure, the machine serial number, as well as shipping and contact information at the time of the call.

Performance Design LLC Boise, ID. Web: www.rhin-o-tuff.com E-mail: pdi@pdibind.com

  • *25 sheet punching capacity is based upon 25 sheets of 20lb copy paper, punching 44 holes on an 11” paper edge.

9/9/2008 3250CL Rev 3

Page 10 of 11

RhinoTuff 3250CL Manual, page 11
Text on page 11

STRONG • SIMPLE • HONEST • CAPABLE

TUFF AND BUILT TO LAST

EASY TO USE & MAINTAIN

TRUSTWORTHY & SOUND

NEVER LETS YOU DOWN

Page 11 of 11 ยท End of manual

Quick start

  1. Set up: Put the machine on a solid surface, plug the power cord into a wall outlet, and turn the power switch on.
  2. Punch: Insert the paper, slide it left, and press the punch button. Punch no more than 25 sheets of paper or 2 sheets of plastic at a time.
  3. Prepare the book: Put the front cover on top and the back cover on the bottom of the book body.
  4. Pick the coil size: Measure the book thickness with the guide on the right side of the accessory tray. The number on the slot tells you the coil size. Match it by sliding coils over the pegs.
  5. Start the coil: Start the coil by hand in the first 3 to 4 holes on the right side. Press the Coil Button to spin the roller. Gently bring the coil to the roller and let it spin into the book.
  6. Crimp: Hold the pliers horizontally with the RED dot facing up. Put the tips around the last coil on the right side and close the pliers completely to cut and crimp.
  7. Crimp the other end: Flip the book over so the back cover is on top and crimp the same way.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine will not punch holes in paperNo powerPlug the power cord into the wall outlet, check that the outlet has power, and switch the machine on. Page 9
Holes punch on the edge of the paperPaper chips in the throat or paper not fully seatedClear paper chips from the throat of the punch die. Seat the paper completely into the bottom of the die. Page 9
Holes punch off centerPaper not against the paper stopMove the paper to the left, against the paper stop, before pressing the punch button. Page 9
Punch will not go through completelyToo many sheetsRemove a couple of sheets from the back of the stack and punch again. Punch only 25 sheets of 20 lb paper or 2 sheets of plastic at a time. Page 9
Punch stopped with pins still in the paperPins did not retractTurn the power off and unplug. Remove the black cap on the right side plate. Turn the shaft counter-clockwise with a flat blade screwdriver until all pins retract. Page 9
Coil will not spin into the bookHoles not aligned or book not shapedAlign the pages so the holes line up. Use the book former to shape the book to the contour of the coil. Page 10
Pliers will not crimp the coilPliers held wrong or coil not heldPoint the RED dot up, hold the pliers horizontally, cut the right side of the book, and hold the coil firmly while closing the pliers. Page 10

Frequently asked questions

How many sheets can the 3250CL punch?

It punches up to 25 sheets of 20 lb copy paper at a time, or 2 sheets of plastic. See page 5.

How do I choose the right coil size?

Measure the book thickness with the guide on the right side of the accessory tray. Move the book from larger to smaller sizes until it just fits. The number on that slot is the coil size. See page 6.

How do I crimp the coil?

Hold the pliers horizontally with the RED dot facing up. Put the tips around the last coil on the right side of the book and close the pliers completely. See page 7.

What do I do if the punch pins stay in the paper?

Turn the power off and unplug the machine. Remove the black cap on the right side plate and turn the shaft counter-clockwise with a flat blade screwdriver until the pins retract. See page 9.

What warranty does the 3250CL have?

It has a 3 year limited warranty against defects in materials and workmanship. The punching die assembly is covered for 1 year. See page 10.