RhinoTuff CI3000 Manual, page 1
Text on page 1

RhinoTuff CI-3000 Coil Inserter

Setup & Operation Manual

Provided By

Page 1 of 10

RhinoTuff CI3000 Manual, page 2
Text on page 2

CI 3000 Coil Inserter

Setup & Operator Manual

Issue 1 April 02 Performance Design Inc.

The CI 3000 plastic spiral inserter will bind books up to 1-1/8” (28.6mm) thick using coil diameters from 3/16” (5mm) up to 1-1/4” (30mm). Any pitch coil can be inserted with this machine.

Table of contents Topic:

  1. Installation Instructions.
  2. Determine the correct coil size.
  3. Determine the correct size mandrel.
  4. Installing the mandrel on the machine.
  5. Adjusting the mandrel bracket.
  6. Adjusting the book guides.
  7. Adjusting the front table / coil guide.
  8. Forward / off / reverse switch.
  9. Inserting a coil.
  10. Drive wheel stop screw.
  11. Cutting a coil.
  12. Troubleshooting

Page 2 of 10

RhinoTuff CI3000 Manual, page 3
Text on page 3

Installation Instructions: Diagram 1 & 2

Keep all clothing and jewelry away from rotating drive wheel.

Power cord shall be certified for the country where the machine will be installed!

♦ Place the CI 3000 on a sturdy table at a good working height. ♦ Use two knobs and washers for each guide and table installed. ♦ Place the right side book guide (spare mandrel holder) (1) next to the drive wheel. ♦ When setting the rear book guide (2) in place, use the set of mounting holes that allow the edge of the book to hang over the edge of machine. (See adjusting book guide section) ♦ The left side extension table (3) will only need to be attached when binding long books. The added support of the table will help the binding process. ♦ Attach the book table / coil guide (4) to the front of the CI 3000.

Page 3 of 10

RhinoTuff CI3000 Manual, page 4
Text on page 4

♦ Place stop screw & spring (5) into front of CI 3000. ♦ Use the large winged knob and washer to install the coil chute / mandrel holder (6) to side of CI 3000. ♦ Thread Motor handle (7) into motor mount. ♦ Plug one end of the power cord into the back of the CI 3000 and the other end into the wall outlet.

  1. Determine the correct coil size.

Use a coil that is at least 3/32” (2.5mm) larger than the book thickness for coil sizes up to 3/4” (20mm). After 3/4”, use a coil size of at least 1/8” over the book size. The larger the coil compared to the book, inserting will become much easier.

  1. Determine the correct size mandrel.

There are a total of nine mandrels, which are used for coil sizes 3/16” (5mm) up to 1-1/4” (30mm). Use the table below, to choose the correct mandrel size to coil size.

3-16” to 1/4” 5/16” 3/8” 7/16” to 1/2” 9/16” 3/4” 7/8” 1” 1-1/8” to 1-1/4”

(5mm-6mm) (7mm-8mm) (9mm-10mm) (11mm-12mm) (13mm-16mm) (17mm-19mm) (20mm-23mm) (24mm-27mm) (28mm-30mm)

Page 4 of 10

RhinoTuff CI3000 Manual, page 5
Text on page 5
  1. Installing the mandrel on the machine. Diagram 3

Keep all clothing and jewelry away from drive wheel during coil insertion!

♦ Place the mandrel (8) into the mandrel holder bracket (9) making

sure the beveled edge of the mandrel is facing the right side of the machine. Both guide posts located on the mandrel need to line up with both slots on the mandrel bracket. Use the black knob (10) to tighten the mandrel in place. ♦ Adjust the height of the mandrel so the center of the mandrel is the same height as the center of the book.

  1. Adjusting the mandrel bracket. Diagram 4

♦ The coil chute / mandrel holder adjustment knob (11) is located on the right side of the CI 3000. Move the assembly toward the drive wheel for small mandrels and away from the drive wheel for the larger mandrels.

Page 5 of 10

RhinoTuff CI3000 Manual, page 6
Text on page 6
  1. Adjusting the book guides. Diagram 5

The right side book guide (12) can be adjusted slightly to the left or the right so the leading edge of the coil lines up with the first hole of the book.

Place the book on top of the CI 3000 with the right side of the book against the right side book guide. Adjust the rear book guide (13) so the holes of the book hang over the edge of the CI 3000. The holes should hang over the edge just enough for the coil to clear the edge of the machine. Tighten all four knobs at this time. It may be necessary to finetune this after a few books are bound for exact placement.

  1. Adjusting the front table / coil guide. Diagram 6

The front table/ coil guide (14) has two purposes. When the coil guide is rotated on top of the coil, it helps assist the coil into the book. Use the coil guide with all book sizes (thickness) until you notice a problem with the coil slipping on the drive wheel or entering the holes in the book. When the coil guide is in the open position, rotated away from the machine, it acts as a support table (15) for larger books. For books over 9/16”, it may be necessary at times to split the book in half using the table to support one half of the book, then finish the inserting of the coil. This method improves productivity.

Page 6 of 10

RhinoTuff CI3000 Manual, page 7
Text on page 7
  1. Forward / off / reverse switch. Diagram 7

The forward / off / reverse (16) switch has three positions. The center position of this switch is the off position and should be placed in this position when not using the machine. Press the front (forward) of the switch and the coil will rotate into the book. Press the back (reverse) of the switch and the coil will exit the book. The reverse feature allows the coil to be removed from the book. Sometimes this will be necessary when the leading edge of the coil misses a hole of a single sheet.

  1. Inserting a coil. Diagram 7 & 8

Place the coil on the mandrel by sliding the open end of the coil onto the beveled end of the mandrel. Turn the coil so it threads onto the mandrel post (17) and is in front of the drive wheel by one coil. Make sure the forward / reverse switch is in the forward position. Pull the motor handle

  1. down to start the motor and engage the drive wheel (19) to the coil.

Rotate the coil so it comes close to the edge of the book, but not past the book. With your right hand, hold the leading edge of the coil and thread it though the first two holes of the book. This helps align the holes of the book. Rotate the coil guide on top of the coil. Pull the handle down gently at first making sure the coil is rotating into the book without missing holes in the sheets or covers. Continue until the coil is past the left side of the book by about one or two coils.

Page 7 of 10

RhinoTuff CI3000 Manual, page 8
Text on page 8
  1. Drive wheel stop screw. Diagram 8

The drive wheel stop screw (20) will prevent the wheel from pressing to hard on the mandrel. It is very important not to have too much pressure on the mandrel when inserting the larger coils. If the leading edge of the coil stops on a misaligned sheet, the coil wants to tie itself into a knot between the book and the end of the mandrel. Setting the stop screw will prevent this from happening most of the time. To set the stop screw, turn it clockwise to push the wheel away from the mandrel. Load the coil onto the mandrel and turn the stop screw counter clockwise while holding down on the motor handle until the drive wheel touches the coil. Try a few books and readjust if necessary.

If the coil chute / mandrel holder is moved after the stop screw has been adjusted, it will be necessary to readjust the stop screw.

Page 8 of 10

RhinoTuff CI3000 Manual, page 9
Text on page 9
  1. Cutting a coil. Diagram 9 & 10

There are, special cutter crimper pliers (ordered separately) that are used to terminate the ends of the coil. After the coil is cut, the sharp end of the coil will tuck itself under the inside of the coil opening. To use the cutter, make sure the red dot (21) is facing up. Place the cutter on the edge of the right hand side of the book. Open the cutter enough so that the end of the cutter enters the coil by about a 1/4”. Make sure the cutter is level with the book before you cut. As you squeeze the cutter you may notice the coil wants to twist. You can support the coil with your fingers as you cut to help stabilize the coil. Turn the book over and repeat these steps on the opposite end of the book. Always make sure to close crimping cutters completely.

Page 9 of 10

RhinoTuff CI3000 Manual, page 10
Text on page 10

Only qualified personnel should attempt to work on this equipment.

Most of the problems you may encounter are due to setup errors. There is one fuse located at the rear of the CI 3000 inserter that can be replaced by the customer. Below is a troubleshooting guide to help you through most of the problems that may be encountered.

Symptom Drive wheel does not rotate. (There is a thermal overload built inside of the motor. Wait several minutes before checking the fuse)

Possible Cause

  1. Machine is off. (Switch is in center position)
  2. Machine not plugged in.
  3. Blown Fuse.

Coil tightens on the mandrel when inserting.

  1. Mandrel is too large for coil.

Coil stops before it is completely through the book.

  1. The holes in the book are misaligned.
  2. The coil is beyond drive wheel.

CI 3000 Electrical Schematic

Action

1) Place switch in either Forward or Reverse position.

2) Check both ends of power cord.

3) Check Fuse 1. (5amp)

1) Select proper size mandrel. (See page 3)

1) This is normal. Try moving the book around so the coil rotates in the holes.

2) Coil length may need to be longer for that particular book. Note: Larger coils can wind themselves open so the length is actually less.

NOTE: The motor is protected by a thermal overload located in the motor. It will reset automatically after the motor cools.

(115 volt AC)

Page 10 of 10 ยท End of manual

Quick start

  1. Set up the machine: Place the CI 3000 on a sturdy table at a good working height. Attach the right side book guide, rear book guide and book table, using two knobs and washers for each.
  2. Connect parts and power: Fit the stop screw and spring, the coil chute and mandrel holder, and the motor handle. Plug the power cord into the machine and a wall outlet.
  3. Pick the coil: Use a coil at least 3/32 inch (2.5mm) larger than the book thickness for coils up to 3/4 inch. Above 3/4 inch, use a coil at least 1/8 inch larger.
  4. Pick the mandrel: There are nine mandrels. Choose the one that matches your coil size from the table in the manual.
  5. Fit the mandrel: Place it in the bracket with the beveled edge facing the right side. Line up both guide posts with the slots. Tighten the black knob. Set its center at the same height as the center of the book.
  6. Set the book guides: Put the book on top with its right side against the right guide. Adjust the rear guide so the holes hang just past the edge. Tighten all four knobs.
  7. Insert the coil: Thread the coil onto the mandrel and put the switch in forward. Pull the motor handle down gently so the coil rotates into the book without missing holes.

Troubleshooting

ProblemLikely causeFix (from the manual)
Drive wheel does not rotateThe switch is in the center off position, the machine is unplugged, or the fuse is blown.Put the switch in Forward or Reverse. Check both ends of the power cord. Check the 5 amp fuse. The motor has a thermal overload, so wait several minutes before checking the fuse. Page 10
Coil tightens on the mandrelThe mandrel is too large for the coil.Select the proper size mandrel. Page 10
Coil stops before it is through the bookThe holes in the book are misaligned, or the coil is beyond the drive wheel.This can be normal. Move the book around so the coil rotates in the holes. The coil may need to be longer for that book. Page 10
Coil ties itself in a knotThe drive wheel presses too hard on the mandrel, especially with large coils.Set the drive wheel stop screw so the wheel just touches the coil. Try a few books and readjust. Readjust it if the coil chute is moved. Page 8
Coil misses a hole in a single sheetThe leading edge of the coil missed a hole.Press the switch to reverse to take the coil back out of the book. Page 7
Coil slips on the drive wheel or does not enter the holesThe coil guide is not on top of the coil.Rotate the coil guide on top of the coil to help it into the book. Page 6

Frequently asked questions

What book thickness can the CI 3000 bind?

It binds books up to 1-1/8 inch (28.6mm) thick with coil diameters from 3/16 inch (5mm) to 1-1/4 inch (30mm). Any pitch coil can be used. See page 2.

How big should the coil be compared to the book?

For coils up to 3/4 inch, use a coil at least 3/32 inch (2.5mm) larger than the book. Above 3/4 inch, use at least 1/8 inch larger. A larger coil is easier to insert. See page 4.

How many mandrels are there?

There are nine mandrels for coil sizes from 3/16 inch (5mm) to 1-1/4 inch (30mm). See page 4.

How do I cut and finish the coil ends?

Use the cutter crimper pliers, which are ordered separately. Make sure the red dot faces up and close the pliers completely. The sharp end tucks under the inside of the coil. See page 9.

What if the coil misses a hole?

Use the reverse position on the forward, off, reverse switch to take the coil back out of the book. See page 7.