Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 1

Page 1 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 2
Text on page 2

Owner's Manual

Paramount 65X GRAPHIC LAMINATION PRODUCTS

Please read and retain these instructions. To register your product, please go to www.royalsovereign.com

Royal Sovereign International Inc.

Page 2 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 3
Text on page 3

CONTENTS

2. Safety Precautions∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 4

6. Control Panel∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8

7. Using Foot Pedal∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9

8. Loading Film∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9

9. Threading Film∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9

9.1 Decaling∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10 9.2 Mounting∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10

Page 3 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 4
Text on page 4

Graphic Lamination Products

Model Paramount 65X

  1. INTRODUCTION

Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all other contents for shipping damage. Damage should be brought to the immediate attention of the delivering carrier

Page 4 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 5
Text on page 5
  1. SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference.

  1. Only a licensed electrician should install wiring and outlet for the laminator.
  2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
  3. Make sure the pressure value is less than 0.6 MPa (87PSI) which can be adjusted it by the regulating valve which is located in the body on the right hand side then connect the air pipe to the air intake.
  4. Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points that can trap body parts or clothing and cause serious injury.
  5. Keep flammable and wet objects away from the machine.
  6. Place machine on a level surface,then set the moveable feet down to floor to keep the machine steady.
  7. Avoid excessive sunlight, humidity and extreme temperatures.
  8. Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/or repairing.
  9. Keep out of reach of children.
  10. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
  11. Do not attempt to laminate items that exceed total recommended material thickness for the unit
  12. When cleaning the machine, don't use flammable sprays or materials.
  13. Do not touch the rollers when they are hot or place foreign objects inside the machine.
  14. Do not cover the surface of the machine until the machine has completely cooled.
  15. In the event of an emergency, press emergency switch immediately.
  16. Temperature of circumstance: 20°C ± 5°C; humidity of circumstance < 95% (20°C ± 5°C)

Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts Away.

Page 5 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 6
Text on page 6

Paramount 65X

  1. INSTALLATION

Note: The laminator should be installed by a trained service technician.

The laminator comes fully assembled, except for the feed table and paper guide to avoid shipping damage. Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damage is reported and a claim is filed with the delivering carrier immediately upon receipt. The laminator should be located in an area with adequate work space for feeding graphics and lamination materials. Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.

Once the laminator is in place, lock the casters into position. Always unlock the casters when moving to a different location.

ELECTRICAL REQUIREMENTS

Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance with electrical codes in your area.

The laminator should have a dedicated power line.

120V UL

230V UL

220V EU

220V AU

240V UK

Page 6 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 7
Text on page 7
  1. INCLUDED WITH LAMINATOR

Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment.

Spare Motor Fuse - FUSE(50T) (6.3A)

Spare Main Power Fuse - FUSE(65TS) 10A/20A

Page 7 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 8
Text on page 8

Paramount 65X

  1. PRODUCT IDENTIFICATION

Film Tension Knob Shaft Release Liner Emergency Switch Roller Safety Sensor Table Front Foot Foot Switch

Shaft Feeder Air Intake Knob Speed Control Button Pressure Gauge Pressure Regulating Valve Pneumatic Toggle Door Lock

Page 8 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 9
Text on page 9
  1. CONTROL PANEL

To change the mode from cold to heat assist. Temperature for heat assist on upper roller is max 122°F/50°C.

To reverse the rollers, press and hold the button.

Rotate the knob to control the roller’s speed from 0 to 19.7 ft/min.

Run/Stop To start or stop the rollers.

Pressure gage: To indicate the pressure of top roller from 0 to 1Mpa (145Psi) pressure value

Pressure regulating valve: To change the pressure of top roller from 0 to 0.6Mpa (87Psi) pressure value

Pneumatic Toggle: To make the top roller go up and down

Page 9 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 10
Text on page 10

Paramount 65X

  1. USING FOOT PEDAL

Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for “Hands Free Operation.” To activate the machine, press the foot pedal once and then release. Repeat to stop the rollers.

  1. LOADING FILM

Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in).

Loading films to upper and lower film shafts: Remove the upper and lower film shafts from the machine and load the films (Center the upper and lower films on the shaft). Note the direction of the adhesives on the lower and upper films

  1. THREADING FILM

Page 10 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 11
Text on page 11

9.1. Decaling

  1. Turn the power switch on (“I” position). The Power switch is located on the rear left side of the unit.
  2. Complete the steps as in the “LOADING FILM” section
  3. Pull the top film down to the bottom of the craft paper/mounting film.
  4. Align and center the craft paper/mounting film to the top film
  5. Peel the top film off

9.2. Mounting

Please adjust the wheel to change the roller pressure with different material for the best laminating quality.

  1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner
  2. With the image facing up, align the image onto the board. Press firmly from the center out.
  3. Adjust the pressure lever to ensure the proper opening.
  4. Flip the image over the upper roller and hold on to the release liner.
  5. Press the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip.

Press the foot pedal once again when the board has completely exited from the rear of the unit. Trim the board if necessary.

  1. MAINTENANCE

Cleaning the Body of the laminator

  1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean.

Removing Adhesive Build Up

  1. Remove the film from the laminator.
  2. Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers.

Note Rub firmly but do not scrub the rollers vigorously as this may scratch the surface. Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.

Lubrication

  1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever comes first.

Page 11 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 12
Text on page 12

Paramount 65X

11. TROUBLESHOOTING

a. Power plug is not plugged in.

Machine will not turn on:

Curled lamination:

a. Plug the power cord into appropriate outlet.

b. Power switch is in “0” (O position.

c. Tripped circuit breaker.

b. Put the power switch to the “I” (On) position.

d. Blown main power fuse.

d. Replace the fuse.

a. Emergency switch(es) is (are) There is power, but the engaged. roller are not turning after

b. Laser safety sight is tripped the “RUN” button is pressed:

The unit is not heating up:

c. Reset the circuit breaker.

a. Disengage the emergency switch(es).

b. Remove obstacles or reposition media

c. Blown motor fuse.

b. Replace the motor fuse.

a. Did not raise the temperature.

a. Raise the temperature.

a. Loosen the top r

b. Loosen the bottom roll film tension

Page 12 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 13
Text on page 13
  1. SPECIFICATIONS

Unit Dimension (w × d × h)

83” x 30” x 50” (2100×750×1250 mm)

Page 13 of 14

Royal Sovereign Paramount 65X 65" Pneumatic Heat Assist Roll Laminator Instruction Manual, page 14
Text on page 14

Paramount 65X

  1. WARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective part or product. These remedies are only available if Royal Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.

All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the equipment was originally purchased. Model, serial number and date of delivery are required for all claims.

The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising out of the use or inability to use this equipment.

LIMITED WARRANTY

This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void this warranty.

CORPORATE HEADQUARTERS

RS International Canada Inc.

2 Volvo Drive, Rockleigh, NJ 07647 U.S.A. TEL : +1) 800-397-1025 FAX : +1) 201-750-1022 E-mail : info@royalsovereign.com

5610 Timberlea Blvd, Mississauga Ontario L4W 4M6 CANADA TEL : +1) 905-461-1095 FAX : +1) 905-461-1096 TF : +1) 866 961-6673 E-mail : info-ca@royalsovereign.com

Royal Sovereign International Inc.

Suite 9, Fitzroy House, Lynwood Drive, Worcester Park, KT4 7AT, United Kingdom Tel. +44 20 3754 5637 Email: rseu@royalsovereign.com & simonkim@royalsovereign.com

www.royalsovereign.com

Page 14 of 14 ยท End of manual

Quick start

  1. Have the laminator installed by a trained technician on a dedicated power line, then lock the casters.
  2. Set the air supply below 0.6 MPa (87 PSI) with the regulating valve on the right side, then connect the air pipe to the air intake.
  3. Turn on the power switch ("I" position) on the rear left side.
  4. Load the upper and lower film shafts, centering the film with the adhesive side facing out from the roll as noted for each shaft.
  5. Choose cold or heat assist on the control panel and set roller speed with the speed knob (0 to 19.7 ft/min).
  6. Use the pneumatic toggle to raise or lower the top roller, and press the foot pedal once to start and again to stop the rollers.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine will not turn onNot plugged in, power switch at "0", tripped circuit breaker, or blown main power fusePlug in, set the switch to "I", reset the breaker, or replace the main power fuse. Page 12
Power is on but rollers do not turn after pressing RUNEmergency switch engaged, safety sensor tripped, or blown motor fuseDisengage the emergency switch, remove obstacles or reposition media, or replace the motor fuse. Page 12
Unit is not heating upTemperature not raisedSwitch to heat assist and raise the temperature. Page 12
Curled laminationFilm tension too highLoosen the top and bottom roll film tension. Page 12

Frequently asked questions

What air pressure does the Paramount 65X need?

Keep the supply under 0.6 MPa (87 PSI), set with the regulating valve on the right side of the machine (page 5).

How hot does the Paramount 65X get?

Heat assist on the upper roller reaches a maximum of 122°F (50°C) (page 9).

How fast does the Paramount 65X run?

Roller speed is adjustable from 0 to 19.7 ft/min with the speed knob (page 9).

How do I remove adhesive from the rollers?

Remove the film, then use a damp (water only) cloth and a rubber gum eraser. Rub firmly but do not scrub, and never use sharp tools, steel wool or abrasives (page 11).

How often should the drive chain be lubricated?

Lubricate the drive chain and sprockets with gear lube or lithium grease every 6 months or 1000 hours, whichever comes first (page 11).