

Page 1 of 17

Text on page 2
Owner's Manual
RBW-1500
BANNER WELDER
Please read and retain these instructions. To register your product, please go to www.royalsovereign.com USA. Click the Customer Support Tab then Registration Tab.
Royal Sovereign International, Inc.
Page 2 of 17

Text on page 3
CONTENTS
- INTRODUCTION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3
- SAFETY PRECAUTIONS∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3
- PRODUCT IDENTIFICATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 5
- INSTALLATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6
4.1 Electrical requirements∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6
4.2 Box contents∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6
4.3 Assembly∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 8
- Control Panel∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 9
- OPERATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 10
- MAINTENANCE∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 11
- TROUBLESHOOTING∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14
- SPECIFICATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15
- RECOMMENDED SETTING∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15
- WARRANTY∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 16
Page 3 of 17

Text on page 4
RBW-1500
- INTRODUCTION
Thank you for choosing a Royal Sovereign RBW -1500. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your Banner Welder, please inspect the box, the machine and all other contents for shipping damage. Damage should be brought to the immediate attention of the delivering carrier (See page 6 for list of shipment elements).
- SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read all instructions carefully and keep for future reference. Royal Sovereign International Inc. cannot be held responsible for any damages to people, animals or objects due to noncompliance with the safety norms and recommendations of these documents.
1. Only a licensed electrician should install wiring and outlet for the Banner Welder.
2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
3. During operation, keep hands away from heating blocks and avoid inserting foreign objects into the machine.
4. Keep flammable and wet objects away from the machine.
5. Place machine on a level surface.
6. Avoid excessive sunlight, humidity and extreme temperatures.
7. Ensure the unit is turned off and unplugged from the outlet prior to moving and/or repairing.
8. Keep out of reach of children.
9. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
10. Do not attempt to weld items that exceed total recommended material thickness for the unit.
13. Tampering with the protections and safety devices is dangerous for the people using the machine and for those exposed to it. Royal Sovereign International Inc. cannot be held responsible for any damages to people, animals or objects due to tampering with the protections.
14. Pay attention to the danger notices on the Banner Welder.
Page 4 of 17

Text on page 5
Dangerous areas and residual risks
To avoid the risk of injury or health problems avoid all moving parts.
Pay attention to hands when operating the Banner Welder.
During certain intervention procedures on the machine, which are pointed out each time in this manual, residual risks for the operator may arise. Residual risks can be avoided by carefully complying with the procedures of this manual and using the personal protection devices indicated. such as:
- Carefully positioning the power cord so that it cannot be stepped on or damaged.
- Maintenance and service operations must be carried out only by the engineers authorized by the manufacturer.
- Pay attention to the danger notices on the Banner Welder.
Banner Welder should only be operated by trained personnel
DO NOT PLACE HANDS NEAR THE HOT ZONE !
Page 5 of 17

Text on page 6
RBW-1500
- PRODUCT IDENTIFICATION
NO
PART NAME
Guide Plate Feed Table Top Cover Speed Knob Body Emergency Switch Rear Cover
NO
PART NAME
Main Switch Adjustable Stand Support Bar
Base
Caster Leveling Legs
Page 6 of 17

Text on page 7
- INSTALLATION
Note: The Banner Welder should be installed and assembled by a trained service technician
The Banner Welder should only be used in an area with the following characteristics:
- Protection from atmospheric agents.
- Proper illumination.
- Normal ambient operating conditions.
4.1 Electrical requirements
Royal Sovereign recommends that licensed electrician ensures proper power installation to your Banner Welder in accordance with electrical codes in your area.
4.2 Box contents
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment.
Page 7 of 17

Text on page 8
RBW-1500
5/16 Hexa Head Bolt Screw (M8*80) Star Washer (Ø8.2)
5/16 Hexa Head Bolt Screw (M8*30)
Wood Screw Washer Plain Fuse (AC250V 10A Lanbao) (100-120V) Fuse (AC250V 6.3A Lanbao) (220-240V)
Fuse (AC250V 4A 5*20)
Page 8 of 17

Text on page 9
4.3 Assembly
- Open the box carton and remove all parts.
- Open the tool-box.
- Attach the caster to the base.(Fig. 4-1)
- Attach the support bar to the base using the supplied screws (M8x80).(Fig. 4-2)
- Attach the adjustable stand to the support bar with a suitable height using the supplied screws (M8x80).(Fig. 4-3)
- Place the Banner Welder body on the adjustable stand and secure it with the supplied screws(M8x30). Adjusting the leveling legs to keep it level and solid.(Fig. 4-4)
- Attach the guide plate to the feed table using the KNOB-BOLT GUIDE. And then fasten the feed table to the work table (Note: work table is not supplied by manufacturer) using the supplied screws.(Fig. 4-5) Attach the second feed table as needed.
Page 9 of 17

Text on page 10
RBW-1500
- The machine is now ready for Operation(Fig. 4-6). Note the recommended component spacing.
2" to 4" gap
6" to 8" gap
5.CONTROL PANEL
- Speed: To adjust the speed of the welding belt, turn the speed knob clockwise to increase speed or counter-clockwise to decrease the speed.
- Temperature: To change the temperature use the up arrow to increase temperature or the down arrow to decrease temperature.
- ST/BY: To switch to stand-by mode (temperature will be automatically set to 176°F) press the ST/BY button.
If the machine is in Stand by Mode and no activity is made for 5 minutes the machine will automatically power off.
- Power: Power button will power the belts and heater on/off. (Note: To completely power the unit on/off, toggle the main switch located near the power cord)
Page 10 of 17

Text on page 11
- OPERATION
The Banner Welder must only be used by trained and qualified personnel.
The Banner Welder must be used only for welding material for which it has been designed.
For recommended maximum welding thickness see page 15.
Welding:
NOTE: When you feed the banner into the machine, you should guide the banner by the hand or by Banner Guide to keep it move in a straight line.
- The Banner Welder should be positioned on a level surface in an area with adequate lighting and enough work space for feeding materials. Connect the power cord to the AC outlet and turn the Power Switch to the on position. Depress the power button on the control panel. The machine should only be operated from the front (control side) of the machine. Welding line
- Before welding, first determine the folded area to be welded, adjust the guide plate and set it to the proper position. Set the temperature and speed referencing the Recommended Temperature and Speed section. (Note: Due to varying manufacturing processes of banner material fine tuning may be required).
- Fold over material to allow for a minimum of 1/2" weld.
- The point of the arrow is the middle of the weld. Align the outer edge Fig. 6-1 of the fold over to the inner edge of the arrow.(Fig. 6-1)
- Guide the banner into machine. The drive belts will grab banner and pull the banner through machine.(Fig. 6-2)
- Welded banner will exit machine.
- Test the weld for tight seal.
- For best results rotate the banner 90° in a clock wise direction. Fold over the short side and guide the banner into the machine with the 4 layer fold entering last. (Note: Turn the speed down 1 to 2 positions to compensate for the extra layers of material). Fig. 6-2
Page 11 of 17

Text on page 12
RBW-1500
- Turn the speed back up and rotate the banner again and fold the longer side of the Sample Pocket Configurations banner and guide the banner into the machine with the 4 layer fold entering last. (Note: Turn the speed back down 1 to 2 positions to compensate for the extra layers of material).
- Turn and weld last end of banner. (Turning the speed down accounting for the extra layers of material).
Pole Pockets:
- Weld all unpocketed sides first. (If you weld pockets before regular sides, your pockets will be sealed closed).
- Loosen the Knob-Bolt Guide on the guide plate on the bottom of the table. Slide guide out to desired depth of pocket. Tighten the knobs on the guide plate
- Weld pocket at slower speed than regular weld side.
Rope Pockets:
- Weld banner the same as with pole pockets only making a smaller rope pocket.
- Insert an electrician's fish tape through pocket and hook on end of rope using a large paper clip. Pull rope through pocket.
Joining Two Pieces Togeather:
1. Cut two pieces to size.
2. Weld one outside edge on each piece.
3. Lay the two pieces together FACE to FACE.
4. Run through machine welding center seam.
7. MAINTENANCE
The banner welding machine has all sealed bearings which do not need any additional lubrication. The only maintenance you may need to perform is replacing the worn out or ripped welding belts, or if you run a printed banner at too high heat, you may need to clean your welding belts.
This is a simple procedure you do while the machine is running.
Page 12 of 17

Text on page 13
- Run a piece of scrap material 2-3 times through the unit. This should clean belts sufficiently.
If you need a more in depth cleaning go to step 2.
- Power the unit off and unplug the unit from the outlet. Once the unit has sufficiently cooled remove the top and bottom cover (as needed) and use a rubber sand belt cleaner to remove residual adhesive from the belts.
DON’T TRY TO REPLACE BELTS WHEN MACHINE IS HOT
Unplug the unit and allow it to sufficiently cool.
- Remove the top/board covers. Unscrew the Philips head screws on the top cover and bottom cover.(Fig. 7-1)
- Remove the drive belt and the three wheels. Push the adjustable base and take off the worn out welding belts.(Fig. 7-2)
Page 13 of 17

Text on page 14
RBW-1500
- To increase or decrease tension on the heating blocks use the adjustment screw, one for the heating block and one for the cooling block.(Fig. 7-3)
- Replace the worn out belts with new belts.
- Loosen the adjustment screw. If the banner is too thick, please tight the adjustment screw.
- Replace the drive belt and three wheels.(Fig. 7-4)
Page 14 of 17

Text on page 15
- Adjust the upper and lower screws to ensure the belts run in the proper position.(Fig. 7-5)
Close to the machine
To move the belts closer to the machine loosen the upper screw and tighten the lower screw.
(To move the belts away from the machine tighten the upper screws and loosen the lower screw).
8.TROUBLE SHOOTING
Symtom
Machine will not turn on
The display show “E0”
The display show “E1”
The display show “E2”
Cause
Possible solution
a. Power switch is in “off”position.
a. Put the power switch to the “on “position
b. Blown main power fuse.
b. Replace the fuse
The emergency switch is in “on” position
Put the switch in “off” position
a. The wire of the upper sensor is abnormal a. Check the wire
b. The upper sensor is broken
b. Replace the upper sensor
a. The wire of the lower sensor is abnormal a. Check the wire
b. The lower sensor is broken
b. Replace the lower sensor
The display show “E3”
The upper sensor is overheated
Check the wire and pcb
The display show “E4”
The lower sensor is overheated
Check the wire and pcb
Page 15 of 17

Text on page 16
RBW-1500
- SPECIFICATION
Model Name
RBW-1500
16 ft./min. ( 0-5m/min)
29"-42" (735 ~ 1055mm)
LED
24" x 15" x 9" (600 x 366 x 216 mm)
Unit Dimensions with Stand
24" x 15" x 42" (600 x 366x 1133 mm )
- RECOMMENDED SETTING
No
Media Thickness
Temperature
Speed
Page 16 of 17

Text on page 17
- WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation. This warranty is valid only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective part or product. These remedies are only available if Royal Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard. All warranty claims must be filed through Royal Sovereign or the authorized Royal Sovereign dealer or reseller through which the equipment was originally purchased. Model, serial number and date of delivery are required for all claims. The obligation to this warranty shall not extend to the following. The adjustment or replacement which are the normal responsibility of the owner. Example Welding Belts, loosened fasteners (bolts, screws etc.) Chipped paint or other items such as fuses that show wear under normal use. Normal operating adjustments to heat, speed or tension. Parts that are not manufactured by Royal Sovereign International Inc. The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising out of the use or inability to use this equipment.
ROYAL SOVEREIGN INTERNATIONAL, INC. 2 Volvo Drive Rockleigh, NJ 07647 USA TEL : +1) 800-397-1025 FAX : +1) 201-750-1022 www.royalsovereign.com
RS INTERNATIONAL CANADA INC. 5610 Timberlea Blvd, Mississauga Ontario L4W 4M6 CANADA TEL: +1) 905-461-1095 FAX: +1) 905-461-1096 TF: +1) 866 961-6673 www.royalsovereign.ca
Page 17 of 17 ยท End of manual
Quick start
- Have the welder assembled by a trained technician: casters to base, support bar and adjustable stand (M8x80 screws), then the body on the stand (M8x30 screws), and level the legs.
- Attach the guide plate and feed table to your work table.
- Plug in, turn on the main switch, then press Power on the control panel; operate only from the front.
- Set the guide plate for the fold, then set temperature with the arrow buttons and belt speed with the speed knob.
- Fold over at least a 1/2" weld, align the outer edge of the fold to the inner edge of the arrow, and guide the banner in straight.
- Test the weld for a tight seal. Turn the speed down 1 to 2 positions when welding over 4-layer corner folds.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine will not turn on | Power switch off or blown main power fuse | Turn the power switch on, or replace the fuse. Page 15 |
| Display shows "E0" | Emergency switch is engaged | Release the emergency switch to the off position. Page 15 |
| Display shows "E1" | Upper sensor wire abnormal or upper sensor broken | Check the wire, or replace the upper sensor. Page 15 |
| Display shows "E2" | Lower sensor wire abnormal or lower sensor broken | Check the wire, or replace the lower sensor. Page 15 |
| Display shows "E3" or "E4" | Upper (E3) or lower (E4) sensor overheated | Check the wire and PCB. Page 15 |
| Adhesive residue on welding belts | Printed banner run at too high a heat | Run scrap material 2 to 3 times through the machine. For deeper cleaning, unplug, let it cool, remove the covers and use a rubber sanding belt cleaner. Page 12 |
Frequently asked questions
How wide a weld should I make with the RBW-1500?
Fold the material over for a minimum 1/2" weld (page 11).
How do I make pole pockets on the RBW-1500?
Weld all unpocketed sides first, slide the guide plate out to the pocket depth, and weld the pocket at a slower speed than a regular hem (page 12).
What does standby mode do?
Pressing ST/BY sets the temperature to 176°F. After 5 minutes of no activity in standby, the machine powers off (page 10).
Does the RBW-1500 need lubrication?
No. It uses sealed bearings. Maintenance is limited to cleaning or replacing worn welding belts, always with the machine unplugged and cool for replacement (page 12).
How fast does the RBW-1500 weld?
Speed is adjustable up to 16 ft./min (0 to 5 m/min) (page 16).
