Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 1

Page 1 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 2
Text on page 2

OWNER'S MANUAL

Read all instructions carefully before use. For any Customer Support needs please choose the Customer Support tab on www.royalsovereign.com

Royal Sovereign International Inc.

www.royalsovereign.com

Page 2 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 3
Text on page 3

TABLE OF CONTENTS

TOPIC∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ PAGE

  1. INTRODUCTION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3
  2. SAFETY PRECAUTIONS∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3
  3. PRODUCT IDENTIFICATION ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 5
  4. INSTALLATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 6 4.1 Electrical requirements∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙6 4.2 Box contents∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙7 4.3 Assembly∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙8
  5. OPERATION∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙11
  6. MAINTENANCE∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 12
  7. TROUBLESHOOTING∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 13
  8. SPECIFICATIONS∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 14
  9. WARRANTY∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 15

Page 3 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 4
Text on page 4
  1. INTRODUCTION

Thank you for choosing a Royal Sovereign trimmer. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your trimmer, please inspect the box, the machine and all other contents for shipping damage. Damage should be brought to the immediate attention of the delivering carrier (See page 7 for list of shipment elements).

  1. SAFETY PRECAUTIONS

Failure to comply with any of the following safety procedures could result in serious injury. Please read all instructions carefully and keep for future reference. Royal Sovereign International Inc. cannot be held responsible for any damages to people, animals or objects due to noncompliance with the safety norms and recommendations of these documents.

  1. Only a licensed electrician should install wiring and outlet for the trimmer.
  2. Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
  3. Keep hands away from cutting blade when in operation.
  4. Keep flammable and wet objects away from the machine.
  5. Place machine on a level surface.
  6. Avoid excessive sunlight, humidity and extreme temperatures.
  7. Ensure the unit is turned off and unplugged from the outlet prior to moving and/or repairing.
  8. Keep out of reach of children.
  9. Only Royal Sovereign authorized maintenance and service technicians should make repairs.
  10. Do not attempt to trim items that exceed total recommended material thickness for the unit.
  11. When cleaning the machine, don't use flammable sprays or materials.
  12. Do not touch the blade when in use or place foreign objects inside the machine.
  13. Tampering with the protections (rear cover, safety cover, protector plate) and safety devices is dangerous for the people using the machine and for those exposed to it. Royal Sovereign International Inc. cannot be held responsible for any damages to people, animals or objects due to tampering with the protections.
  14. Pay attention to the danger notices on the trimmer.

Page 4 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 5
Text on page 5

Dangerous areas and residual risks

All the areas around the machine in which people are at risk of injuries or health problems are considered dangerous. Pay close attention to hands when operating the trimmer. During certain intervention procedures on the machine, which are pointed out each time in this manual, residual risks for the operator may arise. Residual risks can be avoided by carefully complying with the procedures of this manual and using the personal protection devices indicated. such as:

  • Carefully positioning the power cord so that it cannot be stepped on or ruined.
  • Not putting the power cord where it can easily be damaged.
  • Maintenance and service operations must be carried out only by the engineers authorized by the manufacturer.
  • Pay attention to the danger notices on the trimmer.

Trimmer should only be operated by trained personnel

DO NOT PLACE HANDS NEAR THE CUTTING BLADE !

Page 5 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 6
Text on page 6
  1. PRODUCT IDENTIFICATION

PART NAME

Left Side Cover Power Switch Feed Table Front Fabric Holder Rod Protection Plate Foot Pedal Floor Stand Waste Catcher Right Side Cover Rear Cover Activation Bar Safety Cover

Page 6 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 7
Text on page 7
  1. INSTALLATION

Note: The trimmer should be installed by a trained service technician

The trimmer needs to be assembled by a trained installer. The trimmer should only be used in an area with the following characteristics:

  • Protection from atmospheric agents
  • Proper illumination
  • Temperatures between 64° F and 95° F
  • Amount of humidity from 30% to 80%

Royal Sovereign recommends that a licensed electrician ensures proper power installation to your trimmer in accordance with electrical codes in your area.

Page 7 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 8
Text on page 8

4.2 Box contents

Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment.

Main Box

Tool Box

Floor Stand Side Frame

Floor Stand Cross Bar

5/16 Hexa head bolt (M8*55mm)

5/32 screw (M4*8mm) (RET-1652/2002/2502)

Spring washer (Ø4.1) (RET-1652/2002/2502)

Page 8 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 9
Text on page 9
  1. Open the box carton and remove all parts.
  2. Open the tool-box. (Fig. 4-1)

This operation must be carried out by a minimum of two people

  1. Attach the lower cross bar to the left floor stand side frame and right floor stand side frame using the supplied screws (M8x55). (Fig. 4-2)
  2. Slide the holder rods into the adjacent holes of the assembly in accordance with Fig. 4-3. Using pinchers, place the E-rings into the appropriate mounting slots of the holder rods. (Fig.4-4)

Page 9 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 10
Text on page 10
  1. Screw the wastecatcher square bars into the previously inserted wastecatcher holder rods, (Fig. 4-5) putting the supplied screws through the largest drilling in the square bar, so that the head of the screw sits flush within the bar itself. (Fig. 4-6)
  2. Position the main trimmer assembly on top of the floor stand. And properly align the bolt holes. Use bolts (M8x55) to attach the main trimmer assembly to the floor stand. (Fig. 4-7)

Page 10 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 11
Text on page 11
  1. Attach the protection plate (Fig. 4-8) to the upper cross bar with the supplied screws. The protection plate must be assembled on the front part of the upper cross bar, always keeping the table adjustment pin upward.
  2. Connect the power cord in to the AC outlet and turn the Power switch to the ON position.
  3. The Trimmer is now ready for Operation. (Fig. 4-9)

Page 11 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 12
Text on page 12
  1. OPERATION

The trimmer must only be used by trained and qualified personnel. The trimmer must be used only for trimming material for which it has been designed. For recommended maximum cutting thickness see page 14.

  1. The trimmer should be positioned on a level surface in an area with adequate lighting and enough work space for feeding materials. Connect the power cord to the AC outlet and turn the Power switch to the ON position. The machine should be operated from the front of the machine only.
  2. To begin trimming material, position the material to be trimmed on the front feeding table (Fig. 5-1) and measure the cut by using the scales present at either side of the feed table or by the guideline. Do not lean against or put any object on the feeding table during trimming.
  3. When the material is properly positioned press the activation bar (Fig. 5-2) anywhere along the length of the trimmer to activate the cutting blade or step on the foot pedal (Fig. 5-3) to activate the cutting blade. The material can now be removed or repositioned for another cut.

Page 12 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 13
Text on page 13
  1. MAINTENANCE

Standard maintenance

CAUTION: Unplug the trimmer from the power outlet during any maintenance to avoid risk of electric shocks. Note: Only qualified personnel should attempt standard maintenance on the trimmer. Maintenance Procedures Follow below procedures as needed.

Frequency of execution At user's discretion

  • Clean the entire machine with a damp cloth
  • Remove the safety-cover Cleaning the scrap If there is a lot of scrap
  • Eliminate the scrap material with an material material aspirator and/or compressed air
  • Remove the left panel
  • Open the take-fuse connector
  • Remove the burnt fuse
  • Replace it with a new one (3.15A) Replace the fuse of When the fuse is burnt general wiring

Replace the fuse on the electronic board

Replace the electronic board

  • Remove the left panel
  • Remove the burnt fuse
  • Replace it with a new one (2A)

When the fuse is burnt

When the electronic board is broken

  • Remove the left panel
  • Remove the broken electronic board unscrewing the 3 screws for fixing
  • Replace it with a new one

Do not use aggressive products

Wear a pair of protection gloves

Isolate the machine from power supply sourses by unplugging the power cord

Isolate the machine from power supply sourses by unplugging the power cord

Isolate the machine from power supply sourses by unplugging the power cord

Page 13 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 14
Text on page 14
  1. TROUBLESHOOTING

Machine won't turn on. Lamp is off, and main switch is off position

a. Power cord not plugged in

b. Power switch is in “0” off position

c. P ower fuse is blown out

a. Plug the power cord into appropriate position

b. Put power switch back “1” on position

c. Replace main power fuse

a. If the 'led3' on the PCB is off, the fuse on the PCB is blown out

Though power & lamp is 'ON', but cutter won't move after pressing switch button

a. Replace the fuse on PCB

b. Replace either the right or left micro switch

b. If the 'led3' on the PCB is on, either the right or left limit switch is disconnected

For more troubleshooting Queries, please contact Royal Sovereign.

Page 14 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 15
Text on page 15
  1. SPECIFICATIONS

9.1 Technical information

MODEL

RET-1652

RET-2002

RET-2502

9.2 Recommended Trimming Materials

Trimming any material with a thickness exceeding the maximum may dull or damage the cutting blade.

Page 15 of 16

Royal Sovereign RET-2502 98" Wide Format Electric Trimmer Instruction Manual, page 16
Text on page 16
  1. WARRANTY

Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding cutting blades which are warranted for Six (6) months. This warranty is valid only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective part or product. These remedies are only available if Royal Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard. All warranty claims must be filed through Royal Sovereign or the authorized Royal Sovereign dealer or reseller through which the equipment was originally purchased. Model, serial number and date of delivery are required for all claims. The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising out of the use or inability to use this equipment.

LIMITED WARRANTY

This warranty specifically does not cover damage to cutting blade caused by attempted cutting of materials and/or thicknesses of materials other than those specified for use in the user manual, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void this warranty.

ROYAL SOVEREIGN INTERNATIONAL, INC.

RS CANADA INC.

2 Volvo Drive Rockleigh, NJ 07647 USA

1025 Westport Crescent, Mississauga On L5T 1E8 CANADA

TEL : +1) 800-397-1025 FAX : +1) 201-750-1022

TEL : +1) 905-461-1095 FAX : +1) 905-461-1096

TF : +1) 866-961-6673

RS EUROPE LIMITED.

RS INTERNATIONAL AUSTRALIA PTY. LTD.

66 Salisbury Road, Worcester Park, Surrey KT4 7DE UK

30 Prime Drive, Seven Hills, NSW 2147, AUSTRALIA

TEL.: +44) 2082243633

TEL : +61) 2-9674-2127 FAX : +61) 2-9674-2027

Page 16 of 16 ยท End of manual

Quick start

  1. Choose the location: Install the RET-2502 with a trained service technician. The area needs protection from weather, good lighting, 64 F to 95 F and 30% to 80% humidity.
  2. Fit the protection plate: Attach it to the front of the upper cross bar with the supplied screws, keeping the table adjustment pin upward.
  3. Power on: Plug the cord into the AC outlet and turn the power switch to ON. Route the cord where it cannot be stepped on or damaged.
  4. Position the material: Operate only from the front. Lay the material on the front feeding table and measure the cut with the scales on either side or the guideline.
  5. Keep the table clear: Do not lean on the feeding table or put objects on it during trimming. Keep hands away from the cutting blade.
  6. Cut: Press the activation bar anywhere along the trimmer or step on the foot pedal. Then remove or reposition the material for the next cut.
  7. Check thickness: Stay within the recommended maximum cutting thickness (page 14), or the blade can dull or be damaged.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine will not turn on, lamp offThe power cord is unplugged, the power switch is at "0", or the main power fuse is blown.Plug in the cord, set the switch to "1", or replace the main power fuse. Page 14
Power and lamp are on but the cutter will not move when the switch is pressed (LED3 off)With LED3 on the PCB off, the fuse on the PCB is blown.Replace the fuse on the PCB. Page 14
Cutter will not move and LED3 is onThe right or left limit switch is disconnected.Replace either the right or left micro switch. Page 14
Scrap builds up inside the trimmerCut scrap has collected under the safety cover.Unplug the trimmer, remove the safety cover and clear the scrap with an aspirator or compressed air. Page 13
Blade dulls or is damagedMaterial thicker than the maximum for the model is being trimmed.Stay within the recommended maximum thickness for the RET-2502. Page 15
Fuse keeps blowing on the wiring or boardThe general wiring fuse (3.15A) or the electronic board fuse (2A) has burnt.Unplug the machine, remove the left panel and replace the burnt fuse with the same rating. Only qualified personnel should do this. Page 13

Frequently asked questions

How do I start a cut on the RET-2502?

Press the activation bar anywhere along the trimmer or step on the foot pedal once the material is positioned. See page 12.

What room conditions does the trimmer need?

Protection from weather, proper lighting, temperatures from 64 F to 95 F and humidity from 30% to 80%. See page 7.

What fuse sizes does the RET-2502 use?

The general wiring fuse is 3.15A and the fuse on the electronic board is 2A. See page 13.

How long is the warranty?

One year for parts and labor from the installation date. Cutting blades are warranted for six months. See page 16.

Can I clean the trimmer myself?

Cleaning the whole machine with a damp cloth is at the user's discretion. Unplug the trimmer first and avoid aggressive products. See page 13.