

Page 1 of 17

Text on page 2
OWNER'S MANUAL
RSC-LS/LSH/CW/HW SERIES Laminators
Read all instructions carefully before use.
For any Customer Support needs please choose the Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
Page 2 of 17

Text on page 3
TABLE OF CONTENTS
TOPIC
PAGE
2. Safety Precautions............................................................................................... 3
4. Included with Laminator....................................................................................... 5
5. Product Identification............................................................................................ 6
6. Control Panel....................................................................................................... 7
7. Roller Nip Settings............................................................................................... 8
8. Using Foot Pedal and Remote Control................................................................ 8
9. Using Cross Cutter .............................................................................................. 9
10. Loading Film...................................................................................................... 9
11. Threading Film 11.1. Decaling............................................................................................. 10-11 11.2. Mounting................................................................................................. 12
12. Installation of the Front Feed and Rear Rewind Options................................ 13
Page 3 of 17

Text on page 4
RSC-LS/LSH/CW/HW SERIES
- INTRODUCTION
Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your laminator, please inspect the box, the machine and all other contents for shipping damage. Damage should be brought to the immediate attention of the delivering carrier (See page 5 for list of shipment elements).
- SAFETY PRECAUTIONS
Failure to comply with any of the following safety procedures could result in serious injury. Please read the instructions carefully and keep for future reference.
- Only a licensed electrician should install wiring and outlet for the laminator.
- Ensure the unit is plugged into a properly grounded outlet with the correct voltage.
- Keep hands and clothing (i.e. Neckties) away from rollers. The rollers have pinch points that can trap body parts or clothing and cause serious injury.
- Keep flammable and wet objects away from the machine.
- Place machine on a level surface.
- Avoid excessive sunlight, humidity and extreme temperatures.
- Ensure the unit is turned off, cooled, and unplugged from the outlet prior to moving and/ or repairing.
- Keep out of reach of children.
- Only Royal Sovereign authorized maintenance and service technicians should make repairs.
- Do not attempt to laminate items that exceed total recommended material thickness for the unit
- When cleaning the machine, don't use flammable sprays or materials.
- Do not touch the rollers when they are hot or place foreign objects inside the machine.
- Do not cover the surface of the machine until the machine has completely cooled.
- If emergency happen, press emergency switch immediately.
- Temperature of circumstance: 20°C ± 5°C; humidity of circumstance: < 95%(20°C ± 5°C).
Warning - Hazardous Moving Parts – Keep Fingers And Other Body Parts
Page 4 of 17

Text on page 5
- INSTALLATION
Note: The laminator should be installed by a trained service technician.
The laminator comes fully assembled, except for the feed table and paper guide to avoid shipping damage. Upon arrival, thoroughly inspect the unit. It is imperative that any shipping damage is reported and a claim is filed with the delivering carrier immediately upon receipt.
The laminator should be located in an area with adequate work space for feeding graphics and lamination materials.
Avoid placing the laminator in a dusty area or near sources of extreme heat or cold.
Once the laminator is in place, lock the casters into position(“ON” position). Always unlock the casters (“OFF” position) when moving to a different location.
ELECTRICAL REQUIREMENTS
Royal Sovereign recommends that a licensed electrician ensures proper power installation to your laminator in accordance with electrical codes in your area.
The laminator should have a dedicated power line.
120V UL
230V UL
220V EU
220V AU
240V UK
Page 5 of 17

Text on page 6
RSC-LS/LSH/CW/HW SERIES
- INCLUDED WITH LAMINATOR
Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment.
3´´ (76mm) / 2" (57mm) Auto Grip 3´´ (76mm) Auto Grip(America. Canada.Mexico) L-wrench 2.5 ( Stand Assemble ) or
L-wrench 2.5/6 (Stand Separate )
Spare Motor Fuse - FUSE(50T) (6.3A) Spare Main Power Fuse - FUSE(65TS) 5A( RSC-LS/C SERIES )/15A( RSC-LSH/H SERIES )
1/4"Hexa head Bolt (M6 * 20mm) Spring Washer(¢ 6.1) (Included with option only)
3/16"screw (M5 * 12mm). Spring Washer(¢ 5.1) (Included with option only)
Front Feeder and Rear Rewinder Kit (Included with option only))
Page 6 of 17

Text on page 7
- PRODUCT IDENTIFICATION
PART NAME
EMERGENCY SWITCH
FEED TABLE
MAIN ROLLER
ASSEMBLY STAND
FOOT PEDAL
TENSION CONTROL KNOBS
PRESSURE LEVER
CONTROL PANEL
UPPER IDLE BAR
RELEASE LINER TAKE UP
LASER SYSTEM FOR SAFETY
REMOTE CONTROL
FILM SUPPORT
REAR-REWINDER
Page 7 of 17

Text on page 8
RSC-LS/LSH/CW/HW SERIES
- CONTROL PANEL
When the machine is initially turned on, the LED display window will show the speed set at 1.
RSC-LSH/HW SERIES
RSC-LS/CW SERIES
- SPEED DISPLAY: Display’s current Speed.
- SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button.
- HEAT BUTTON : To select HEAT(122℉,50℃) or COLD mode.
- REV: To reverse the rollers, press and hold the REV button.
- RUN: To start the rollers.
- STOP: To stop the rollers.
Page 8 of 17

Text on page 9
- ROLLER NIP SETTING
It is important to adjust the roller nip settings to the appropriate thickness of the board being used. Use the guide below to adjust to the correct position.
Metric (mm)
Laminating
m 13m 10- .5 in 0.4-0
15-18mm 0.6-0.7 in
If you don't want to laminate, please place the pressure leverto the "Open position(NO.7)".
- USING FOOT PEDAL AND REMOTE CONTROL
USING FOOT PEDAL
Place the foot pedal on the floor in front of the
machine. Once all correct settings are displayed, you
may use the foot pedal to operate the laminator for
“Hands Free Operation.” To activate the machine,
press the foot pedal once and then release. Repeat to
USING REMOTE CONTROL
Located on the rear left side of the laminator.
- PRESS REV – To reverse the rollers. Press and
hold the button (useful for jams or misted media).
- PRESS STOP – To stop the rollers from turning.
- PRESS FWD – To activate the rollers.
Page 9 of 17

Text on page 10
RSC-LS/LSH/CW/HW SERIES
- USING CROSS CUTTER
The cross cutter is located on the rear exit table of the machine.
1. After lamination, move the cutter approximately to the center of the completed application at the desired point of detachment (Figure 1).
2. Grasp film with one hand, press the cutter downward into the application and slide it first to one end of the application, then to the other end to complete the cut (Figure 2 & 3).
10. LOADING FILM
Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in).
Loading films to upper and lower film shafts: (See page 5 for assistance with parts identification.)
- Adjust the auto grip to fit to the film and tighten the auto grip screw (Figure 1).
- Remove the upper and lower film shafts from the machine and load the films (Center the upper and lower films on the shaft). Note the direction of the adhesives on the lower and upper films (Figure 2).
- Load the upper and lower film shafts on the machine (Figure 3).
Page 10 of 17

Text on page 11
- THREADING FILM
TAKE UP DEVICE
COLD FILM
PAPER BACK
HOT ROLLER
UPPER IDLE BAR
BACKING PAPER
BASE FILM
LOEWER IDLE BAR
11.1. Decaling
- Turn the power switch on (“I” position). The Power switch is located on the rear left side of the unit.
- C omplete the steps as in the “LOADING FILM” section (see page 10).
- Set the top roller to the desired temperature .
- Take off the Frame-Paper Guide and the Feed Table.
- Pull the top film down over the Safety Cover to the bottom of the craft paper/mounting film.
- Align and center the craft paper/mounting film to the top film and tighten the two lower core screws (Figure 1).
- Thread the top film underneath the Upper Idle Bar. (Figure 2)
- Tape the top film on to the Release Liner Take-Up. (Figure 2)
Page 11 of 17

Text on page 12
RSC-LS/LSH/CW/HW SERIES
9. C ut and separate the release liner and the film. (Figure 3)
10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4)
11. R einstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover.
12. Adjust the nip setting to appropriate gap.
13. Insert and push the leader board until they reach the front nip point.
14. Push the Run button.
15. Push the leader board into the rollers. (Figure 5)
16. Adjust the top and bottom tension knob by rotating it clockwise or counterclockwise. Turn it until the top and bottom roll films have some resistance (The tension varies depending on the film thickness; the thicker the film the more tension is required). (Figure 6)
7. Press the Stop button when the leader board has completely exited from the rollers.
18. Use the Cross Cutter to cut the leader board from the web (see page 9).
19. Set the nip setting to the appropriate position for the Over-lamination / Decaling application.
Page 12 of 17

Text on page 13
11.2 Mounting
- Lay the decaled image face down on a flat surface. Carefully peel back and put a crease along the edge of the release liner (Approximately 1 inch or 25mm, Figure 1).
- With the image facing up, align the image onto the board. Press firmly from the center out (Figure 2).
- Adjust the pressure lever to ensure the proper opening (Figure 3).
- Flip the image over the upper roller and hold on to the release liner (Figure 4).
- Press the foot pedal once, and then let it go while slowly pulling the release liner as the board enters the main roller nip (Figure 5).
Press the foot pedal once again when the board has completely exited from the rear of the unit. Trim the board if necessary.
Page 13 of 17

Text on page 14
RSC-LS/LSH/CW/HW SERIES
- INSTALLATION OF FRONT FEEDER and REAR REWINDER
OPTIONS
NOTE: Below options are to be installed by an authorized RS reseller.
Installation of the Front Feeder Option (Includes 2 brackets, one spindle, and mounting hardware).
- Install the Front Feeder to the inside of the front frames using four 1/4" (M6) hexagon bolts on each side (Figure 1).
Installing the Rear Rewinder Option (Includes motorized winder, bracket, one spindle, and mounting hardware).
- Remove the left and right covers by using a screwdriver (four screws on each side cover) (Figure 2 & 3).
- Remove the lever knob screw and lever (Figure 4).
- Disassemble the power switch bracket and place the left rewinder outside of the frame; fasten with round head 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 5).
- Install the right rewinder on the outside of the frame and connect the motor wire connector to the rear wire (Figure 6 & 7).
- Reinstall the rear cover.
- Reinstall the side covers.
- Reinstall the lever knob and screw.
Page 14 of 17

Text on page 15
- MAINTENANCE
Cleaning the Body of the laminator
1.To clean the machine body, dampen a cloth with water only and gently wipe the
machine clean.
Removing Adhesive Build Up
- Remove the film from the laminator.
- Use a damp (water only) cloth and a rubber gum eraser to remove the adhesive on the Teflon (metal) and silicone rollers.
Note: Rub firmly but do not scrub the rollers vigorously as this may scratch the surface. Do not use sharp metal objects, steel wool, or abrasives, as these may also damage the rollers.
1. Drive chain and sprockets should be lubricated with either a light coat of gear lube or heavy grease (lithium grease) after 6 months or 1000 hours of operation, whichever comes first.
14. TROUBLESHOOTING
Machine will not turn on:
There is power, but the rollers are not turning after the “RUN” button is pressed:
a. P ower plug is not plugged in.
b. P ower switch is in “0” (Off) position.
c. T ripped circuit breaker.
d. B lown main power fuse.
a. Emergency switch(es) is (are) engaged.
b. Paper guide is not installed correctly.
c. Blown motor fuse.
a. Plug the power cord into appropriate outlet.
b. Put the power switch to the “I” (On) position.
c. Reset the circuit breaker.
d. Replace the fuse.
a. Disengage the emergency switch(es).
b. Properly install the paper guide so that the micro switch is activated.
d. Replace the motor fuse.
The unit is not heating up:
a. Did not raise the temperature.
a. Raise the temperature.
Curled lamination:
a. Upward curl.
b. Downward curl.
a. Loosen the top roll film tension.
b. Loosen the bottom roll film tension.
Page 15 of 17

Text on page 16
RSC-LS/LSH/CW/HW SERIES
- SPECIFICATIONS
DESCRIPTION
RSC-1401LS/LSH
RSC-1402CW/HW
AC100V, 200V, 220~240V 50/60Hz
100W(Others) 160W(US,CA)
RSC-1651LS/LSH
Laser system for safety
Thickness of substrated (Paper)
Chain link to main motor
YES
2"&3"Auto Grip or 3"Auto Grip(America. Canada. Mexico)
Take of Main Motor
Foot S / W
Page 16 of 17

Text on page 17
- WARRANTY
Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the customer’s sole and exclusive remedy under this warranty shall be, at Royal Sovereign’s option, to repair or replace any such defective part or product. These remedies are only available if Royal Sovereign’s examination of the product discloses to Royal Sovereign’s satisfaction that such defects actually exist and were not caused by misuse, neglect, attempt to repair, unauthorized alternation or modification, incorrect line voltage, fire, accident, flood or other hazard.
All warranty claims must be filed through the authorized Royal Sovereign dealer or reseller through which the equipment was originally purchased. Model, serial number and date of delivery are required for all claims.
The warranty made herein is in lieu of all other warranties, expressed or implied, including any warranty or merchantability or fitness for a particular purpose. Royal Sovereign will not be liable for personal damage or personal injury (unless primarily caused by its negligence), loss of profit, or other incidental or consequential damages arising out of the use or inability to use this equipment.
LIMITED WARRANTY
This warranty specifically does not cover damage to laminating rollers caused by knives, razor blades, or any sharp objects or abrasives, or failure caused by adhesives, or damage caused by lifting, tilting or improper use of the machine. Warranty repair or replacement by Royal Sovereign or its authorized Reseller(s) does not extend the warranty beyond the initial one year period from the date of installation. Unauthorized customer alterations will void this warranty.
RS EUROPE LIMITED.
CORPORATE HEADQUARTERS
Royal Sovereign International Inc.
2 Volvo Drive, Rockleigh, NJ 07647 U.S.A. TEL : +1) 800-397-1025 FAX : +1) 201-750-1022 E-mail : info@royalsovereign.com
66 SALISBURY ROAD, WORCESTER PARK, SURREY KT4 7DE UK TEL : +44) 2082243633 E-mail : rseu@royalsovereign.com
RS International Australia PTY. LTD.
5610 Timberlea Blvd, Mississauga Ontario L4W 4M6 CANADA TEL : +1) 905-461-1095 FAX : +1) 905-461-1096 TF : +1) 866 961-6673 E-mail : info-ca@royalsovereign.com
30 Prime Drive, Seven Hills, NSW 2147, Australia TEL : +61) 2-9674-2127 FAX : +61) 2-9674-2027 E-mail : salesaust@royalsovereign.com
Page 17 of 17 ยท End of manual
Quick start
- Place and lock: Set the RSC-1402HW on a level surface with room to feed material. Lock the casters in the "ON" position. Use a dedicated power line installed by a licensed electrician.
- Load the films: Royal Sovereign film is wound adhesive in. Adjust the auto grip to fit the film and tighten its screw. Center the films on the shafts, then put the shafts back in the machine.
- Power on: Turn the power switch to "I" on the rear left of the unit. Set the top roller to the desired temperature.
- Thread it: Take off the Frame-Paper Guide and the Feed Table. Pull the top film down over the Safety Cover, thread it under the Upper Idle Bar and tape it to the Release Liner Take-Up. Reinstall the feed table and paper guide and close the Safety Cover.
- Set the nip and feed: Adjust the roller nip to match the board thickness. Push the leader board to the front nip point, press Run and push it into the rollers. Turn the tension knobs until the films have some resistance.
- Control the rollers: Press the foot pedal once to start and again to stop. The remote control has FWD, STOP and REV. Hold REV to back out a jam. Press the emergency switch in an emergency.
- Finish and cut: Press Stop when the board clears the rollers. Cut it from the web with the cross cutter. Put the pressure lever in the open position when you are not laminating.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine will not turn on | Not plugged in, power switch at "0", tripped breaker, or blown main power fuse | Plug in, switch to "I", reset the breaker, or replace the main fuse. Page 15 |
| Power is on but rollers do not turn after pressing RUN | Emergency switch engaged, paper guide not installed correctly, or blown motor fuse | Disengage the emergency switch, install the paper guide so its micro switch is activated, or replace the motor fuse. Page 15 |
| Unit is not heating up | Temperature was not raised | Raise the temperature (select heat mode). Page 15 |
| Lamination curls upward | Top roll film tension too high | Loosen the top roll film tension. Page 15 |
| Lamination curls downward | Bottom roll film tension too high | Loosen the bottom roll film tension. Page 15 |
Frequently asked questions
How hot does the RSC-1402HW get?
In heat mode the top roller runs at 122°F (50°C). You can also run it in cold mode (page 8).
How do I use the remote control?
The remote is on the rear left side: hold REV to reverse the rollers (useful for jams), press STOP to stop and FWD to run (page 9).
What spare fuses come with the laminator?
A 6.3A motor fuse and a 15A main power fuse for the RSC-1402HW (page 6).
How do I clean adhesive off the rollers?
Remove the film and use a damp (water only) cloth and a rubber gum eraser. Do not use sharp tools, steel wool or abrasives (page 15).
How often should the drive chain be lubricated?
Every 6 months or 1000 hours, whichever comes first, with gear lube or lithium grease (page 15).
