

Page 1 of 2

Text on page 2
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
INSTRUCTIONS FOR:
EUROPA Cutter rail
Models: 4010,11,12,13,14,15,16,17,18,19
Thank you for purchasing a SSM product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT WAS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. ONLY LIFT OR MOVE THE EUROPA CUTTER RAIL USING THE CIRCULAR GRIP ON THE TOP OF THE RAIL. IF YOU NEED TO HANDLE THE CUTTER IN ANY OTHER WAY OR IF YOU NEED TO MOVE IT AWAY FROM ITS CUTTING TABLE, THE BLADE MUST BE REMOVED FIRST.
CONTENTS
After unpacking the EUROPA Cutter rail, check to make sure that you have all the parts and that there is no damage to the machine. 1.1 EUROPA Cutter rail components: Rail and cutting head already assembled One (1) blade cartridge Box of 100 utility blades One (1) scoring blades One (1) textile blade cartridge One (1) textile blades One (1) allen key (2mm) OPERATION 2.1 It is important that the EUROPA Cutter rail is used on a flat surface. A warped or bowed table top can induce a twist in the rail resulting in a curved cut. Always use a cutting mat or other sacrificial material. 2.2 Loosen the BLADE CLAMP THUMB SCREW (See 1 below) and insert a cartridge. The utility blade and scoring blade cartridges are inserted from the rear of the holder (See 2 below), the textile blade cartridge is inserted from the front (See 3 below). 2.3 UTILITY BLADE - The utility blade can be located in any one of 4 positions depending on the thickness of material being cut (See 4 below). Fine adjustment can be carried out by undoing the BLADE CLAMP THUMB SCREW (See 1 below) and moving the cartridge itself. To cut lightweight materials, place your right hand on the cutter head, depress the cutter and pull the cutting head towards you (See 8 below). To cut heavyweight materials, place your left hand on the circular grip and apply downward pressure, place your right hand on the cutter head, depress the cutter with the palm of your hand and push away from you to cut (See 9 below). Multiple passes may be needed for thicker materials. SCORING BLADE - The scoring blade should be located in the cartridge as shown in 5 below. To score fracture sensitive plastics such as acrylic use the same technique as used for cutting heavyweight materials (see above). To break, move the material so that the score line runs along the font edge of the table and using the cutter as a clamp, apply downward pressure to the overhanging plastic to break. (SAFETY GLASSES AND GLOVES
SHOULD BE WORN)
TEXTILE BLADE - To cut, use the same technique as used for cutting lightweight materials (see above). Blades can be replaced by undoing the knurled brass knob on the rear of the unit.
GENERAL MAINTENANCE
3.1 Regularly clean the EUROPA Cutter rail using a dry cloth, stubborn stains can be removed with a cloth dampened with a little water/detergent. 3.2 Silicon spray can be used to lubricate the cutting head slideway. NEVER USE OIL OR SPIRITS TO LUBRICATE OR CLEAN THE EUROPA CUTTER RAIL, SOME OF THE PLASTIC COMPONENTS AND BEARINGS MAY BE DAMAGED.
ADJUSTING THE CUTTING HEAD BEARINGS
4.1 The bearings used to control the CUTTING HEAD are made from a high quality polymer and under normal use will last for an extremely long time. As they settle into position you may find a slight amount of side play, this can be removed by tightening the two adjustment screws (See 7 below).
Spare parts can be obtained by calling 763-755-1600
1. Blade Clamp Thumbscrew
2. Inserting From The Rear
3. Inserting From The Front
7. Bearing Adjustment Screws
4. Blade Positions
9. Push To Cut
Page 2 of 2 · End of manual
Quick start
- Place the cutter on a flat table and always cut onto a cutting mat or other sacrificial material.
- Loosen the blade clamp thumb screw and insert a cartridge: utility and scoring cartridges from the rear, the textile cartridge from the front.
- Set the utility blade in one of 4 positions to suit the material thickness; fine-tune by moving the cartridge.
- Lightweight materials: hand on the cutter head, depress the cutter and pull the head towards you.
- Heavyweight materials: left hand on the circular grip pressing down, right palm depressing the cutter, and push away from you. Use multiple passes for thick material.
- Scoring acrylic: score using the heavyweight technique, then align the score line with the table edge and press down on the overhang to break (wear safety glasses and gloves).
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Curved cut | A warped or bowed table top twisting the rail | Use the cutter on a flat surface with a cutting mat. Page 2 |
| Slight side play in the cutting head | Polymer bearings settling into position | Tighten the two bearing adjustment screws. Page 2 |
Frequently asked questions
What blades come with the Europa?
A utility blade cartridge with a box of 100 utility blades, a scoring blade, and a textile blade cartridge with a textile blade, plus a 2mm Allen key. See page 2.
Can it cut acrylic?
Yes, by scoring with the scoring blade and then breaking the sheet over the table edge, using the cutter as a clamp. See page 2.
How do I lubricate the cutting head?
Use silicone spray on the slideway. Never use oil or spirits, which can damage plastic parts and bearings. See page 2.
How do I change the textile blade?
Undo the knurled brass knob on the rear of the unit. See page 2.
