Safety Speed Nemesis Integrated Large Format Desktop Cutters User Manual, page 1

Page 1 of 3

Safety Speed Nemesis Integrated Large Format Desktop Cutters User Manual, page 2
Text on page 2

INSTRUCTIONS FOR:

NEMESIS Cutting system

Models: 4110,11,12,13,14,15,16,17,18,19

Thank you for purchasing a SSM product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT WAS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.

PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE. ONLY LIFT OR MOVE THE NEMESIS CUTTER RAIL USING THE CIRCULAR GRIP ON THE TOP OF THE RAIL. IF YOU NEED TO HANDLE THE CUTTER IN ANY OTHER WAY OR IF YOU NEED TO MOVE IT AWAY FROM ITS CUTTING TABLE, THE BLADE MUST BE REMOVED FIRST.

DO NOT REMOVE THE PACKAGING BANDS UNTIL INSTRUCTED (See A below)

CONTENTS

After unpacking the NEMESIS Cutting system, check to make sure that you have all the parts and that there is no damage to the machine. 2.1 NEMESIS Cutting system components: Cutter rail, base and end plates assembly RH & LH Handle assemblies One (1) blade cartridge Box of 100 utility blades One (1) scoring blades One (1) textile blade cartridge One (1) textile blades One (1) allen key (2mm)

ASSEMBLY

3.1 Position the cutter on the table in its operating position, cut the packing bands and remove them from underneath the cutter. (See B below) 3.2 Using a 17mm wrench, fit a lifting handle to each end. Once tightened, the handles should move freely without any sideways movement. (See C below) 3.3 Check that the cutter is in the correct position on the table and check that the base plate and end plates are in line. (See D below) 3.4 Attach the two end plates to the table using the pan head screws provided. (See E below) 3.5 Check that each lifting handle operates correctly. 3.6 Remove the cutter from both guide rods by lifting vertically. 3.7 Using the countersink head screws provided, fix the base plate to the table. (See F below) 3.8 Check the grip of the Nemesis cutter rail by using an A4 piece of paper (this instruction sheet is ideal). Place the paper under one end of the Cutter rail and try to pull the paper free. The weight of the Cutter rail should be enough to grip the paper. Repeat this test along the entire length of the Cutter rail and if necessary use paper, plastic or card spacers under the full width of the base to make it level. 3.9 If you want to make the table top flush with the aluminium base plate, build up the table using 6mm MDF or similar.

Page 2 of 3

Safety Speed Nemesis Integrated Large Format Desktop Cutters User Manual, page 3
Text on page 3

OPERATION

4.1 Loosen the BLADE CLAMP THUMB SCREW (See 1 below) and insert a cartridge. The utility blade and scoring blade cartridges are inserted from the rear of the holder (See 2 below), the textile blade cartridge is inserted from the front (See 3 below). 4.2 UTILITY BLADE - The utility blade can be located in any one of 4 positions depending on the thickness of material being cut (See 4 below). Fine adjustment can be carried out by undoing the BLADE CLAMP THUMB SCREW (See 1 below) and moving the cartridge itself. To cut lightweight materials, place your right hand on the cutter head, depress the cutter and pull the cutting head towards you (See 8 below). To cut heavyweight materials, place your left hand on the circular grip and apply downward pressure, place your right hand on the cutter head, depress the cutter with the palm of your hand and push away from you to cut (See 9 below). Multiple passes may be needed for thicker materials. SCORING BLADE - The scoring blade should be located in the cartridge as shown in 5 below. To score fracture sensitive plastics such as acrylic use the same technique as used for cutting heavyweight materials (see above). To break, move the material so that the score line runs along the font edge of the table and using the cutter as a clamp, apply downward pressure to the overhanging plastic to break. (SAFETY GLASSES AND GLOVES SHOULD BE WORN) TEXTILE BLADE - To cut, use the same technique as used for cutting lightweight materials (see above). Blades can be replaced by undoing the knurled brass knob on the rear of the unit.

GENERAL MAINTENANCE

5.1 Regularly clean the NEMESIS Cutting system using a dry cloth, stubborn stains can be removed with a cloth dampened with a little water/detergent. 5.2 Silicon spray can be used to lubricate the cutting head slideway. NEVER USE OIL OR SPIRITS TO LUBRICATE OR CLEAN THE NEMESIS CUTTER RAIL, SOME OF THE PLASTIC COMPONENTS AND BEARINGS MAY BE DAMAGED.

ADJUSTING THE CUTTING HEAD BEARINGS

6.1 The bearings used to control the CUTTING HEAD are made from a high quality polymer and under normal use will last for an extremely long time. As they settle into position you may find a slight amount of side play, this can be removed by tightening the two adjustment screws (See 7 below).

SPARE PARTS

7.1 Spare parts can be obtained by calling 763-755-1600.

1. Blade Clamp Thumbscrew

2. Inserting From The Rear

3. Inserting From the Front

7. Bearing Adjustment Screws

8. Pull To Cut

9. Push To Cut

4. Blade Positions

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 3 of 3 · End of manual

Quick start

  1. Position the cutter on the table, then cut and remove the packing bands.
  2. Fit a lifting handle to each end with a 17mm wrench; handles should move freely without side play.
  3. Line up the base and end plates, screw the end plates to the table, lift the cutter off the guide rods and screw the base plate down.
  4. Check grip by pulling a sheet of A4 paper from under the rail along its length; level with spacers if needed.
  5. Loosen the blade clamp thumb screw and insert a cartridge: utility and scoring cartridges from the rear, the textile cartridge from the front.
  6. Set the utility blade in one of 4 positions to suit the material thickness; fine-tune by moving the cartridge.
  7. Lightweight materials: hand on the cutter head, depress the cutter and pull the head towards you.
  8. Heavyweight materials: left hand on the circular grip pressing down, right palm depressing the cutter, and push away from you. Use multiple passes for thick material.

Troubleshooting

ProblemLikely causeFix (from the manual)
Curved cutCutter base not level or not gripping evenlyCheck grip with a sheet of paper along the rail and level the base with paper, plastic or card spacers. Page 2
Slight side play in the cutting headPolymer bearings settling into positionTighten the two bearing adjustment screws. Page 3

Frequently asked questions

What blades come with the Nemesis?

A utility blade cartridge with a box of 100 utility blades, a scoring blade, and a textile blade cartridge with a textile blade, plus a 2mm Allen key. See page 2.

Can it cut acrylic?

Yes, by scoring with the scoring blade and then breaking the sheet over the table edge, using the cutter as a clamp. See page 3.

How do I lubricate the cutting head?

Use silicone spray on the slideway. Never use oil or spirits, which can damage plastic parts and bearings. See page 3.

How do I change the textile blade?

Undo the knurled brass knob on the rear of the unit. See page 3.