Page 1 of 3
Text on page 2
OPERATOR’S MANUAL
Standard Jog-Fast Jogger
Read this manual, and thoroughly familiarize yourself with its contents before operating or servicing this equipment.
JOGFAST/OP/PAR
Revised 7/99
Standard Duplicating Machines Corporation 10 Connector Road, Andover, MA 01810 (978) 470-1920 Fax (978) 470-2771
JOGFAST/OP/PAR
Revised 7/99
Page 2 of 3
Text on page 3
INTRODUCTION:
Thank you for selecting the Standard Jog-Fast TM Jogger. The Standard Jog-Fast TM Jogger has been developed for ease of operation and maintenance, however, we recommend that you familiarize yourself with the machine by carefully reading these instructions.
WARNING: THIS MACHINE CONTAINS MOVING PARTS THAT CAN CATCH HAIR OR LOOSE CLOTHING AND PINCH FINGERS. DURING OPERATION AND MAINTE- NANCE KEEP HANDS, HAIR AND LOOSE CLOTHING CLEAR OF MOVING PARTS. SERVICE OR DISASSEM- BLY SHOULD BE DONE WITH POWER CORD DISCON- NECTED.
INSTALLATION:
Remove Jog-Fast TM Jogger from carton. Remove 2 bolts at bottom which secure packing material to jogger.
PARTS LIST
Plug unit into any 115V 60HZ/A.C. outlet. Turn Switch “ON”. (a light will indicate “ON” position.) Load paper.
MAINTENANCE:
Lubricate bearings with light oil every 6 months. Occasionally, if necessary, remove any debris from bearings with a brush or an air jet stream. See parts list for bearing locations.
KEY DESCRIPTION
PART NO. QUAN. KEY DESCRIPTION
14. Motor Base
1. Base W-0400001
15. Counter Shaft
2. Top Cover-R.H.
W-0400002
16. Bearing-Flange
3. Top Cover-L.H.
W-0400003
17. Set Collar
4. Switch M-S033051
18. Washer-Nylon
5. Bumpers M-S030045
19. Thrust Washer
6. Side Panel-R.H.
W-0400008
20. Counterweights
7. Side Panel-L.H.
W-0400009
21. Spring Washer
8. Side Bckt.-R.H.
W-0400010
22. Bearing
9. Side Bckt.-L.H.
W-0400011 1
23. Motor Base Bckt.
10. Wood Tray-Bottom W-0400006
24. Motor Coupling
11. Wood Tray-Back W-0400007
25. Clamps
12. Springs M-S031074
26. Suction Cups
13. Motor M-S021030
PART NO. W-0400014 W-0400005 M-S013010 M-S037302 M-S019024 M-S008088 W-0400004 M-S008086 M-S013047 W-0400013 W-0400012 M-S037314 M-S030048
QUAN.
Page 3 of 3 · End of manual
Quick start
- Remove the jogger from the carton and take out the 2 bolts at the bottom that secure the packing material.
- Plug the unit into a 115V 60Hz AC outlet.
- Turn the switch on; a light shows it is on.
- Load the paper.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Hair, clothing or fingers caught in the machine | The machine has moving parts that can catch hair or loose clothing and pinch fingers. | Keep hands, hair and loose clothing clear of moving parts during operation and maintenance. Page 3 |
| Machine is being serviced or taken apart | Power is still connected. | Disconnect the power cord before any service or disassembly. Page 3 |
| Machine does not run after unpacking | The packing bolts or power connection may be missed. | Remove the 2 bolts at the bottom that hold the packing material. Plug into a 115V 60HZ AC outlet and turn the switch ON. A light shows the ON position. Page 3 |
| Bearings are dirty or not moving freely | Debris has built up in the bearings, or they are not lubricated. | Brush off debris or use an air jet if needed. Lubricate the bearings with light oil every 6 months. Page 3 |
Frequently asked questions
How do I maintain the Jog-Fast jogger?
Lubricate the bearings with light oil every 6 months and remove debris from the bearings with a brush or air jet if needed. Always disconnect the power cord before service (page 3).
What power does the Jog-Fast need?
Any 115V 60Hz AC outlet (page 3).
What is the part number for the Jog-Fast motor?
The parts list gives the motor as M-S021030 (page 3).
What are the part numbers for the switch and springs?
Switch M-S033051 and springs M-S031074 (page 3).
