

Page 1 of 47

Text on page 2
PC-45
PAPER CUTTER
Important Information
- This manual is designed to help you to install, operate and maintain Paper Cutter, PC-45.
Read, understand and keep this manual in a safe and convenient place.
- Do not operate PC-45 until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages resulting from : improper or inadequate maintenance by customer; unauthorized modification or misuse; operation outside of the environmental specifications for the product.
- Horizon International Inc. pursues a policy of continuing improvement in design and performance of the product. Therefore, the product design and specifications are subject to change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or translated to another language without the prior written consent of Horizon International Inc.
071114/PC45/09E/DV
Page 2 of 47

Text on page 3
Safety Precautions
- The signal word WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
- The signal word CAUTION indicates a potentially hazardous situation which, if not avoided, may result in damage on machines. It may also be used to alert against unsafe practices.
- Read and understand all safety instructions with signal word such as WARNING and CAUTION. If safety instructions are ignored, personal injury may result.
- Horizon International Inc. cannot anticipate every possible situation that might involve a potential hazard. The instructions in this manual and warning labels on the machine are therefore not all inclusive.
- All equipment shall be locked out or tagged out to protect against accidental or inadvertent operation when such operation could cause injury to personnel. Do not attempt to operate any switch, valve, or other energy isolating device where it is locked or tagged out.
- Do not operate the machines when any covers are removed.
- Some of the drawings in this manual show the machine uncovered for explaining the detail or inside of machine.
Page 3 of 47

Text on page 4
CONTENTS
Important Information ............................................................................................ I
Safety Precautions .................................................................................................... II
- Before You Begin
1-1 Purpose of PC-45 ............................................................................................... 2
1-2 Specifications ...................................................................................................... 2
1-3 Machine Descriptions ........................................................................................ 3
1-3-1 Safety Functions ............................................................................................. 3 1-3-2 Main Parts Descriptions ................................................................................. 4
1-4 Accessories .......................................................................................................... 5
1-5 Consumables ...................................................................................................... 6
- Safety Function Check
2-1 Check on Table .................................................................................................. 8
2-2 Check on Power ................................................................................................. 8
2-3 Check on Safe Functions ................................................................................... 9
2-3-1 Check on Standby Button ............................................................................... 9 2-3-2 Check on Front Cover .................................................................................... 9
2-3-3 Check on Automatic Return of Knife ............................................................. 10 2-3-4 Check on One Cycle ....................................................................................... 10
2-3-5 Check on Unworkable Knife with One Hand ................................................ 11 2-3-6 Check on Stop during Working ...................................................................... 11
- Operation Procedure
3-1 Operation Procedure ......................................................................................... 14
- After Cutting
4-1 Original Condition ............................................................................................. 18
4-2 Power off ............................................................................................................. 18
4-3 Cleaning Table ................................................................................................... 19
Page 4 of 47

Text on page 5
- Troubleshooting
5-1 Cut Sheets Are Not Square ............................................................................... 22
5-2 Cut Surface Has Diagonal Lines ...................................................................... 23
5-3 Sheets Are Not Cut Equally .............................................................................. 23
5-4 Sheets Are Not Cut Even After the Power Is Turned On .............................. 24
- Maintenance
6-1 Cutting Stick Replacement ............................................................................... 26
6-2 Knife Replacement ............................................................................................. 28
6-2-1 Knife Removal ............................................................................................... 28 6-2-2 Knife Installation ............................................................................................ 31
6-3 Knife Height Adjustment .................................................................................. 34
6-3-1 Cutting Depth Adjustment.............................................................................. 34
6-4 Cutting Depth Balance Adjustment ................................................................. 35
6-5 Test Cutting ........................................................................................................ 36
6-6 Lubrication (Monthly) .......................................................................................37
- Installation
7-1 Installation .......................................................................................................... 40
Page 5 of 47

Page 6 of 47

Text on page 7
- Before You Begin
1-1 Purpose of PC-45
Horizon PC-45 is a machine for cutting printed sheets, wrapping paper, writing paper, or booklets.
1-2 Specifications
(Clamp Opening) 70 mm (2.7")
120 V 60 Hz 13 A,
220 V 50/60 Hz 4.0 A,
240 V 50 Hz 2.3 A
Machine Dimensions (L) x (W) x (H)
790 x 805 x 1,170 mm (31.1" x 31.7" x 46")
Height from the floor level to table top
158 kg (348 lb)
The machine design and specifications are subject to change without any notice.
Page 7 of 47

Text on page 8
- Before You Begin
1-3 Machine Descriptions
Cut Button B Knife works when cut buttons A and B are pressed at the same time. Knife stops immediately when either cut button A or B is released.
Page 8 of 47

Text on page 9
- Before You Begin
1-3 Machine Descriptions
1-3-2 Main Parts Descriptions
Clamper Hand Wheel This wheel is used to raise/lower clamper.
Clamper This clamper presses sheets not to move during cutting. Back Gauge Locking Screw This screw locks the back gauge not to move after the back gauge is fit to position cutting width.
Back Gauge Dial This dial is used to measure cutting width.
Back Gauge Handle This handle is used to move back gauge either forward or backward. Back gauge is moved by 5 mm when this handle makes one turn. Scales are used to adjust cutting position. Scales are marked in 0.5 mm intervals. When this handle is pulled, it is free to move.
Back Gauge This gauge is used to position cutting width.
Side Gauge and Back Gauge Scale This gauge is used to square-up both sides of sheets.
Page 9 of 47

Text on page 10
- Before You Begin
1-4 Accessories
Spare Knife and Knife Case
Allen Wrench 3mm, 4 mm, 6mm, 8mm
Page 10 of 47

Page 11 of 47

Text on page 12
2. Safety Function Check
2. Safety Function Check
2-1 Check on Table ........................................................................................ 8
2-2 Check on Power ....................................................................................... 8 2-3 Check on Safe Functions ......................................................................... 9
Page 12 of 47

Text on page 13
- Safety Function Check
2-1 Check on Table
Table must be clean.
- Check that trimmings, adhesive, or grease
is not on table.
NOTE
- Clean table referring to "4-3 Cleaning table" if table is dirt.
2-2 Check on Power
Check that power turns on.
- Insert key into power switch and turn key
clockwise to switch on power.
CUTT
- Power pilot lamp will illuminate.
POW
ER B
OFF
Page 13 of 47

Text on page 14
- Safety Function Check
2-3 Check on Safe Functions
WARNING
- Do not put your hands under knife while power is on.
- Assign only "ONE" operator to operate PC-45.
If your PC-45 do not work as shown in this book, ask your local dealer to fix the PC-45.
2-3-1 Check on Standby Button
Check that knife work only when Standby button is pressed.
Check that the lamp on Standby button is turned off.
- Lower clamper to the bottom with clamper
- Check that knife does not work in spite of
pressing cut buttons A and B at the same time.
- Press the Standby button.
- Check that the Standby button lights.
2-3-2 Check on Front Cover
Check that knife do not work while front cover is open.
- Lower clamper to the bottom with clamper
- Open front cover.
- Check that knife does not work in spite of
pressing cut buttons A and B at the same time.
- Close front cover.
Page 14 of 47

Text on page 15
- Safety Function Check
2-3 Check on Safe Functions
2-3-3 Check on Automatic Return of Knife
Check that knife at bottom position returns to home position automatically and then stops.
- Press cut buttons A and B at the same
- Release your hands from cut buttons when
knife is on the way to home position.
- Check that knife returns to home position without stopping and then stops at home position.
2-3-4 Check on One Cycle
Check that knife remains stationary if cut buttons are continued to press after knife returns to home position.
- Continue pressing to cut buttons about 5
seconds after knife returns to home position. Check that knife does not work again.
Next, check that knife remains stationary unless both hands are released from cut buttons.
- Release your hand from cut button B with
cut button A pressed.
- Press cut button B again. Check that knife
Page 15 of 47

Text on page 16
- Safety Function Check
2-3 Check on Safe Functions
2-3-5 Check on Unworkable Knife with One Hand
Check that knife work only when both cut buttons A and B are pressed at the same time.
- Check that knife does not work by press-
ing only cut button A.
- Check that knife does not work by press-
ing cut button B with cut button A pressed.
NOTE
- Knife works only when both cut buttons A and B are pressed at the same time (within 5 seconds).
- Release your hands from cut buttons.
- Check that knife does not work by repeat-
ing procedure 1 to 3, exchanging A with B.
2-3-6 Check on Stop during Working
WARNING
- Do not raise clamper when knife is stopped during cutting. Otherwise knife gets bare and, as a result, your fingers might be cut with knife.
NOTE
- Knife can return to home position by pressing cut button A and B separately with the interval of 0.5 seconds or more when knife is stopped on the way to bottom.
- Repeat procedure 1, exchanging A with B.
Check that knife is stopped when you release your hand from even one cut button during lowering knife.
- Check that knife is stopped immediately
when you release your hand from cut button A while knife is lowering after you press cut button A and B at the same time.
- Release your hands from cut buttons.
- Press cut button A and B separately with
the interval of 0.5 seconds or more to return the knife to the home position.
Page 16 of 47

Page 17 of 47

Page 18 of 47

Text on page 19
3-1 Operation Procedure
This section shows how to operate PC-45.
WARNING
- Do not put your hands under knife while power is on.
- Assign only "ONE" operator to operate PC-45.
- It is dangerous to remain knife on half position for fear of cutting hands or fingers. Make sure to return knife to home position.
CAUTION
- Cut only paper sheets. Otherwise PC- 45 may be broken.
- Turn on power with key switch.
- Press the Standby button.
- Check that the Standby button lights.
- Turn clamper hand wheel counterclock-
wise to raise clamper.
Back Gauge Locking Screw
- Loosen the back gauge locking screw.
- Adjust back gauge according to cutting
with back gauge handle.
NOTE
- Move back gauge from rear side to front side. Otherwise, it errs in cutting width.
- Cutting line helps to see cutting position.
Cutting line is the beam that is reflected on sheets.
- Tighten the back gauge locking screw.
Page 19 of 47

Text on page 20
3-1 Operation Procedure
- Open front cover and pile sheets on table.
- Square-up sheets with back gauge and side
- Turn clamper hand wheel, and clamper
will press sheets to fix them.
NOTE
- Be careful not to shift sheets when fixing sheets.
- Close front cover.
- Continue to press cut button A and B at
the same time, and knife lowers and cuts sheets. You may release cut buttons when knife begins to rise because knife returns to home position automatically.
NOTE
- If you fail to press both cut buttons at the same time, release your hands from buttons and try it again 2 seconds later.
- If you release your hand(s) from cut button(s) while knife is lowering and cutting operation is stopped, press cut button A and B separately with the interval of 0.5 seconds or more, and knife returns to home position.
Page 20 of 47

Text on page 21
- Make sure knife has returned to home
- Release your hands from cut buttons.
- Turn off power with key switch.
- Open front cover and remove trimmings on
- Loosen clamper hand wheel by turning it
- Take cut sheets out of table.
- Repeat procedure 1 to 14. Back gauge is
not required to adjust in the case of the same cutting width.
Page 21 of 47

Page 22 of 47

Text on page 23
4-1 Original Condition
Clamper must be lowered to the bottom after finishing operation.
- Lower clamper to the bottom by turning
clamper hand wheel clockwise.
- If knife remains on half way, press cut
button A and B separately with the interval of 0.5 seconds or more to return the knife to the home position.
4-2 Power off
Power is turned off.
WARNING
CUTT
POW
- Only authorized operators should have access to key switch.
ER B
OFF
- Turn off power by turning key switch
- When turning on the power again, turning it on after the Standby button completely goes out.
- Pull out key and keep it.
Page 23 of 47

Text on page 24
4-3 Cleaning Table
Clean table after operating PC-45.
- Make sure power is off.
CUTT
POW
ER B
OFF
- Lower clamper to the bottom by turning
clamper hand wheel clockwise.
- Wipe trimmings off table with soft cloth.
Page 24 of 47

Page 25 of 47

Text on page 26
- Troubleshooting
5-1 Cut Sheets Are Not Square ..................................................................... 22
5-2 Cut Surface Has Diagonal Lines ............................................................ 23 5-3 Sheets Are Not Cut Equally.................................................................... 23 5-4 Sheets Are Not Cut Even After the Power Is Turned On ................... 24
Page 26 of 47

Text on page 27
5-1 Cut Sheets Are Not Square
(Cause) Back gauge is not parallel to knife.
Length A and B is different.
Tools:
- Wrench 5 mm
- Wrench 4 mm
Back Gauge Fix Screws
- Turn off power with key switch.
- Remove transparent cover in back gauge
- Loosen back gauge fix screws and adjust
back gauge with adjust screw.
Fasten Screw B
- Back gauge moves clockwise by loosening screw A and fastening screw B. Length B is shortened by moving back gauge clockwise.
- Fasten back gauge fix screw after adjust-
ing of back gauge.
- Turn on power and check that edges are
Back Gauge Fix Screws
parallel by test cutting.
- Repeat procedure 1 to 4 until one edge
Loosen Screw B
Page 27 of 47

Text on page 28
5-2 Cut Surface Has Diagonal Lines
(Cause) Knife is worn or nicked.
(Remedy) Replace knife with new one referring to "6-2 Knife Replacement".
Cut Surface
5-3 Sheets Are Not Cut Equally
(Cause 1) Clamper presses sheets too strongly or knife moves forward slightly as knife moves down.
(Remedy) Weaken clamper pressure or replace knife with new one.
(Cause 2) Weak clamper pressure sometimes causes bow-shaped section. Less than 20˚ angle of knife sometimes also causes knife to cut inward sheets.
(Remedy) Tighten clamper or replace knife with new one.
Page 28 of 47

Text on page 29
5-4 Sheets Are Not Cut Even After the Power Is Turned On
(Cause) The Standby button is not pressed.
(Remedy) Press the Standby button.
Page 29 of 47

Text on page 30
- Maintenance
6-1 Cutting Stick Replacement ..................................................................... 26 6-2 Knife Replacement .................................................................................. 28 6-3 Knife Height Adjustment ........................................................................ 34
6-4 Cutting Depth Balance Adjustment ...................................................... 35 6-5 Test Cutting .............................................................................................. 36
6-6 Lubrication (Monthly) ............................................................................ 37
Page 30 of 47

Text on page 31
6-1 Cutting Stick Replacement
When the groove on cutting stick gets deep, last sheet is left uncut or torn off. Replace cutting stick with new one.
WARNING
- Do not touch knife. Otherwise you may be injured.
NOTE
- If knife remains on half way, press cut button A and B separately with the interval of 0.5 seconds or more to return the knife to the home position.
CUTT
POW
OFF
Tool:
- Turn off power by turning key switch
- Turn clamper hand wheel counterclock-
wise to raise clamper fully.
- Insert Straight Screwdriver into the bot-
tom of cutting stick and remove cutting stick.
ER B
Page 31 of 47

Text on page 32
6-1 Cutting Stick Replacement
- Replace face of cutting stick with new
NOTE
- One face of cutting stick provides two working line. Replace face with another new face after both two lines on the same face are used.
Two Lines on One Face
- Turn clamper hand wheel clockwise to
lower clamper to the bottom.
Page 32 of 47

Text on page 33
6-2 Knife Replacement
This section shows how to replace knife.
CAUTION
- Replace knife in the following conditions;
- Some sheets are left uncut.
- Cutting noise gets louder.
- Trimmed sheets are not separated smoothly.
- Knife stops during cutting.
- When some sheets are left uncut, knife does not need to be replaced by adjusting cutting depth, but use of worn knife cause some troubles. Replace knife with new one when knife cuts sheets about 500 times.
Remove knife to replace it with new one.
WARNING
- Wear gloves when knife is replaced.
- Be careful of knife. Do not touch knife.
- Knife may cause serious injury.
- Be careful of removed knife. Do not put it on unstable place with knife bare.
Tools;
1. Felt Pen
2. Box Wrench
3. Two Knife Holder
1. Turn off power with key switch.
2. Turn clamper hand wheel to lower
clamper to the bottom.
- Make sure knife is on home position.
- Open front cover.
- Mark knife position on clamper with felt
NOTE
- This mark is used to adjust knife position.
- Close front cover.
Page 33 of 47

Text on page 34
6-2 Knife Replacement
- Turn on power with key switch.
- Press cut buttons A and B to lower knife
until all four knife securing bolts appear.
NOTE
- Do not lower knife too low. Otherwise knife cannot be removed.
Cut Button A Key Switch
- Turn off power with key switch.
- Press the Standby button.
- Check that the Standby button lights.
- Open front cover.
- Remove the center two of four knife secur-
ing bolts with box wrench.
- Fasten knife holders enough.
WARNING
- Fastening knife holder insufficiently may cause knife to fall and severe injury to operators as a result. Do fasten knife holder completely as shown in the drawing below.
Page 34 of 47

Text on page 35
6-2 Knife Replacement
- Loosen the rest of two knife securing bolts
15 Remove knife securing bolts with box
wrench turning knife holder clockwise not to fall knife.
- Slide knife to the left and remove it slowly.
WARNING
- Knife may cause serious injury if you touch it lightly. Take care knife is not touched by other persons or falls.
- Put knife on safe place, remove knife
holder, put knife in knife case, and request to sharpen knife to your local dealer or knife resharping shop.
Page 35 of 47

Text on page 36
6-2 Knife Replacement
This section shows how to install knife.
WARNING
- Wear gloves when knife is replaced.
- Be careful of knife. Do not touch knife directly.
- Knife may cause serious injury.
- Be careful of removed knife. Do not put it on unstable place with knife bare.
NOTE Sharpening Specifications
- Knife must be grounded to an angle of 20˚.
- Grind knife as little an necessary.
- Sharpened knife must have at least 65 mm height. Replace knife whose height is less than 65 mm with new one.
- Turn off power with key switch.
CUTT
POW
OFF
- Make sure all four knife securing holes
ER B
Page 36 of 47

Text on page 37
6-2 Knife Replacement
- Fasten two knife holders in center two
holes in the right drawing.
NOTE
- Be careful not to mistake the right side of knife.
The Right Side of Knife
WARNING
- Fastening knife holder insufficiently may cause knife to fall and severe injury to operators as a result. Do put screw section of knife holder completely as shown in the drawing below.
- Open front cover.
- Raise knife holders fitting knife securing
groove and slide knife holders to the right.
- Fasten knife securing bolts with box
wrench, lifting knife with knife holder.
- Remove knife holder and fasten two knife
securing bolts there with box wrench.
Page 37 of 47

Text on page 38
6-2 Knife Replacement
- Close front cover.
- Turn on power with key switch.
- Press the Standby button.
- Check that the Standby button lights.
- Press cut button A and B separately with
the interval of 0.5 seconds or more to return the knife to the home position.
WARNING
CUTT
- Do not lower knife until knife adjustment is finished. Otherwise PC-45 may be broken.
POW
OFF
- Turn off power with key switch.
ER B
Page 38 of 47

Text on page 39
6-3 Knife Height Adjustment
6-3-1 Cutting Depth Adjustment
Cutting depth must be adjusted after knife replacement.
WARNING
- Operating PC-45 before cutting depth is adjusted may cause some troubles.
- Turn clamper hand wheel to lower pres-
- Unplug power cord.
- Open knife adjust cover.
NOTE
- Turn lock nut clockwise to loose lock nut.
- Loosen two lock nuts of knife height
adjust screws with spanner.
- Turn turnbuckle with adjust bar into adjust
screws hole to fit knife with the mark with felt pen.
NOTE
- 1/6 turn of knife height adjust bolts raise/ lower knife about 0.6 mm. Excessive cutting pressure does harm to PC-45. Maximum cutting depth is 0.5 mm.
- Fasten two locknuts.
- Close knife adjust cover on the bottom.
Page 39 of 47

Text on page 40
6-4 Cutting Depth Balance Adjustment
Cutting depth balance adjustment is required when cutting pressure is not the same in left and right sides.
Left Adjustment Section Cover
WARNING
- Handle knife with utmost care. Do not touch knife.
CAUTION
- After adjusting cutting depth balance, knife height adjustment is required in some case.
- Open left adjustment section cover.
- Loosen lock bolt with allen wrench.
- Insert allen wrench into balance adjust
shaft hole and adjust knife height.
NOTE
- The left side of knife rises/lowers by turning balance adjust shaft.
- Fasten lock bolt with allen wrench.
- Close cover of adjustment section.
Balance Adjust Shaft Hole
Page 40 of 47

Text on page 41
6-5 Test Cutting
Check on knife cutting condition.
WARNING
- Do not put your hands and fingers under knife. Otherwise you may be injured seriously.
- Do not put your hands under knife while power is on.
- Assign only "ONE" operator to operate PC-45.
- It is dangerous to remain knife on half position for fear of cutting hands or fingers. Make sure to return knife to home position.
- Place sheets on both edge of table one by
- Turn power on with key switch.
- Press the Standby button.
- Check that the Standby button lights.
- Operate PC-45 referring to "3-1 Operation
- If both sheets are left uncut partially,
adjust knife height again. (Page 32)
- If either paper is left uncut partially, adjust
Page 41 of 47

Text on page 42
6-6 Lubrication (Monthly)
Lubricate the following sections to maintain PC-45 in the best condition.
- Turn on power with key switch.
- Press the Standby button.
- Check that the Standby button lights.
- Turn clamper hand wheel to lower
clamper to the surface of table.
- Press cut buttons A and B to lower knife.
Release cut buttons when clearance between knife and cutting stick is about 5 mm, and knife will stop.
- Turn off with key switch.
- Open adjustment section covers (right and
- Lubricate sliding faces between marks.
- Close tops of lubricate section.
Page 42 of 47

Text on page 43
6-6 Lubrication (Monthly)
- Open knife adjust cover and apply grease
on driving and rotating section. (Arrow marks)
- Close knife adjust cover.
- Turn on power with key switch.
- Press cut button A and B separately with
the interval of 0.5 seconds or more to return the knife to the home position.
Page 43 of 47

Page 44 of 47

Text on page 45
7-1 Installation
Place PC-45 properly according to its machine dimensions.
WARNING
- PC-45 weighs about 160 kg/332 lb totally. Move it with utmost care.
- Do not grip back gauge handle or clamper hand wheel when PC-45 is moved because serious injury may be caused and back gauge and clamper may lack in precision.
CAUTION
- Select flat floor considering the machine weight (about 160 kg/332 lb).
- Select a place free from extremely high temperature and humidity.
- Unpack the machine and remove four
locking plates (at the front and rear).
Page 45 of 47

Text on page 46
7-1 Installation
Assembling the pedestal for PC-45.
- Insert one end of the prop (3 pcs) into the
large holes at the right leg and fix the props with the spring washers and the hexagon head bolts with using of the supplied box wrench.
- Put the back panel on the props and
secure them to the left leg.
Hook Back
- Place the both semi-assembled legs on the
flat floor and secure firmly the hexagon head bolts at the left leg.
- Fit a top lid on the top panel and mount it
on the leg assembly as shown in the right drawing.
- Mount the PC-45 machine on the top
panel so that the hooks on the right leg are fitted in the bottom notches of the PC-45 machine.
2 Top Panel 1 Hexagon 3 Top Lid 1 Bolts
Page 46 of 47

Text on page 47
- Place PC-45 on the stand in correct direc-
NOTE
- Make sure PC-45 is not placed on hook.
- Install clamper hand wheel.
- Install back gauge handle.
- Connect ground wire. (Contact electrical
- Plug power plug into outlet.
Page 47 of 47 ยท End of manual
Quick start
- Turn on the power with the key switch and press the Standby button so it lights.
- Turn the clamper hand wheel counterclockwise to raise the clamper.
- Loosen the back gauge locking screw, set the cutting width with the back gauge handle (moving from rear to front) and retighten the screw.
- Open the front cover, stack the sheets and square them against the back gauge and side gauge.
- Turn the clamper hand wheel to clamp the sheets without shifting them, then close the front cover.
- Press cut buttons A and B together and hold them until the knife starts to rise; it returns home automatically.
- Turn off the key switch, open the cover, remove trimmings, loosen the clamper and take out the cut sheets.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Cut sheets are not square | The back gauge is not parallel to the knife. | Turn off power, remove the back gauge transparent cover, loosen the fix screws, adjust with the adjust screws, retighten and test cut. Page 27 |
| Cut surface has diagonal lines | The knife is worn or nicked. | Replace the knife. Page 28 |
| Sheets are not cut equally | Clamper pressure is too strong or too weak, or the knife is worn or ground below a 20 degree angle. | Adjust the clamper pressure or replace the knife. Page 28 |
| Sheets are not cut after power is turned on | The Standby button has not been pressed. | Press the Standby button. Page 29 |
| Last sheet is left uncut or torn | The groove on the cutting stick is too deep. | Turn the cutting stick to a new line or face, or replace it. Page 31 |
| Knife stopped partway down | A cut button was released during the cut. | Do not raise the clamper. Press cut buttons A and B separately, at least 0.5 seconds apart, to return the knife home. Page 16 |
Frequently asked questions
What is the clamp opening of the PC-45?
The clamp opening is 70 mm (2.7") (page 7).
How often should the PC-45 knife be replaced?
Replace it after about 500 cuts, or when sheets are left uncut, cutting gets louder, trimmed sheets do not separate smoothly or the knife stops during cutting (page 33).
What are the knife sharpening specifications?
Grind to a 20 degree angle, removing as little as needed. A sharpened knife must be at least 65 mm high (page 36).
How do I adjust the cutting depth?
Unplug the machine, open the knife adjust cover, loosen the two lock nuts and turn the adjust screws. A 1/6 turn moves the knife about 0.6 mm; maximum cutting depth is 0.5 mm (page 39).
What power does the PC-45 need and how heavy is it?
120 V 60 Hz at 13 A (220 V and 240 V versions also listed). It weighs 158 kg (348 lb) and measures 790 x 805 x 1,170 mm (page 7).
