Page 1 of 21
Text on page 2
PC-64II
PAPER CUTTER
Important Information
- This manual is designed to help you to install, operate and maintain Paper Cutter, PC- 64II. Read, understand and keep this manual in a safe and convenient place.
- Do not operate PC-64II until you read and understand the instructions in this manual.
- Horizon International Inc. shall not be liable for incidental consequential damages resulting from : improper or inadequate maintenance by customer; unauthorized modification or misuse; operation outside of the environmental specifications for the product.
- Horizon International Inc. pursues a policy of continuing improvement in design and performance of the product. Therefore, the product design and specifications are subject to change without prior notice and without our legal obligation.
- All rights are reserved. No part of the manual may be photocopied, reproduced or translated to another language without the prior written consent of Horizon International Inc.
090617/PC64II/04E/DV
Page 2 of 21
Page 3 of 21
Page 4 of 21
Page 5 of 21
Page 6 of 21
Page 7 of 21
Text on page 8
IMPORTANT:
- Knife will come to a stop instantly when one or both buttons are released before knife reaches its lowest point. To reverse movement of knife depress cut buttons A & B separately with the interval of 0.5 seconds or more. Knife will reverse direction. Hold cut button until knife stops at home position (upper position).
- If knife is past it's lowest position it should return automatically to home position even if cut buttons are released.
ADDITIONAL INFORMATION
- If the front cover is opened while the knife is moving, the buzzer beeps and the knife lamp lights.
In this case, follow the steps below to move the knife to the home position.
- Close the front cover.
- In case that the knife stops during raising because the front cover is opened, the knife returns to the home position automatically after closing the cover.
If the knife still stay there, go to the next step.
- Press the cut button A first, and then press the cut button B after 0.5 seconds or more.
- The knife returns to the home position automatically.
f
- Cut cycle complete.
- Ensure knife stops at home position (upper position).
- Turn off power switch.
- Remove trimmings. (Fig. 2-4)
- Turn paper clamp hand wheel (Fig. 2-4) counterclockwise until paper lift is released.
- Remove lift of paper.
- Job complete.
- Turn key switch off and remove key. (Fig.
2-4)
- Unplug power cord.
IMPORTANT:
Keep key switch at safe place by an authorized operator.
Page 8 of 21
Page 9 of 21
Page 10 of 21
Page 11 of 21
Text on page 12
- Turn on power.
- Cycle knife by depressing cut buttons A and B separately with the interval of 0.5 seconds or more to return the knife to the home position.
(Fig. 4-5)
Page 12 of 21
Page 13 of 21
Page 14 of 21
Page 15 of 21
Page 16 of 21
Page 17 of 21
Page 18 of 21
Text on page 19
Table Fix Bolt Back Table
Backgauge Screw
Backgauge Handle Shaft
Position the back table so that the tip of this screw hits against the casting frame.
- Side Guide (C) on front table should be aligned with side guide (B) on back table.
Page 19 of 21
Text on page 20
120V 60Hz 14A 220V 50Hz 5.6A 220V 60Hz 6.8A 240V 50Hz 5.9A
990 mm (W) (38.9") 1120 mm (D) (44.1") 1280 mm (H) (50.4")
Distance from floor up to table top
290 kg (638 lb)
- Back Gauge Dial at Front Table
- Counter
- Automatic Knife Return to Home Position
- Illuminated Cutting Line
Page 20 of 21
Page 21 of 21 ยท End of manual
Quick start
- Align the tables: position the back table so the tip of the backgauge screw hits against the casting frame. The side guide (C) on the front table should be aligned with side guide (B) on the back table.
- Power on and home the knife: turn on power, then press cut buttons A and B separately with an interval of 0.5 seconds or more to return the knife to the home position.
- Cut: use cut buttons A and B. The knife stops instantly if one or both buttons are released before it reaches its lowest point.
- Finish the cycle: make sure the knife stops at the home position (upper position), turn off the power switch, and remove trimmings.
- Release and shut down: turn the paper clamp hand wheel counterclockwise until the lift is released and remove it. Turn the key switch off, remove the key and unplug the power cord.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Knife stops before finishing the cut | One or both cut buttons were released before the knife reached its lowest point | To reverse the knife, press cut buttons A and B separately with an interval of 0.5 seconds or more, and hold until the knife stops at home position. Page 8 |
| Buzzer beeps and the knife lamp lights | The front cover was opened while the knife was moving | Close the front cover. The knife returns to the home position automatically. Page 8 |
| Knife stays put after the front cover is closed | The knife stopped while raising because the cover was opened | Press cut button A first, then press cut button B after 0.5 seconds or more. The knife returns to home automatically. Page 8 |
| Knife is not at home position on power up | Knife is away from the home position | Turn on power and cycle the knife by pressing cut buttons A and B separately with an interval of 0.5 seconds or more. Page 12 |
| Cannot remove the paper lift after cutting | Paper clamp is still holding the lift | Turn the paper clamp hand wheel counterclockwise until the paper lift is released. Page 8 |
| Back table does not line up with the front table | Back table is not positioned correctly | Position the back table so the tip of the screw hits the casting frame, and align side guide (C) on the front table with side guide (B) on the back table. Page 19 |
Frequently asked questions
What power does the PC-64II need?
It is listed at 120V 60Hz 14A, 220V 50Hz 5.6A, 220V 60Hz 6.8A, and 240V 50Hz 5.9A. See page 20.
How big and heavy is the PC-64II?
It is 990 mm (W) x 1120 mm (D) x 1280 mm (H) (38.9" x 44.1" x 50.4") and weighs 290 kg (638 lb). See page 20.
How do I reverse or return the knife?
Press cut buttons A and B separately with an interval of 0.5 seconds or more, and hold until the knife stops at home position. See page 8.
What features does the PC-64II have?
It has a back gauge dial at the front table, a counter, automatic knife return to home position, and an illuminated cutting line. See page 20.
