

Page 1 of 2

Text on page 2
EPS8RBLK
size: 140X101mm ( 5.5”x4”)
HOW TO USE YOUR BOSTITCH ® QUIETSHARP EXECUTIVE™ ELECTRIC PENCIL SHARPENER
- Insert the AC plug into the nearest, easily-accessible 120-volt outlet.
- Insert pencil into the opening, Motor will start automatically.
- The TipSaver™ feature indicates that your pencil is sharpened by a change in motor sound and by decreased resistance. Do not force the pencil any further.
- Remove sharpened pencil from unit to prevent motor damage.
MAINTENANCE & SAFETY INSTRUCTIONS. To ensure smooth, trouble-free sharpening: .Make sure the receptacle is in place and tightly closed before operating your sharpener. .Empty the receptacle on a regular basis. The pencil sharpener will not operate properly when full. .Always unplug the sharpener before cleaning or emptying the receptacle. .Do not sharpen writing instruments such as crayons, chalk, or soft waxy pencils as they will clog your sharpener’s cutters. .Clean the cutters if they become clogged. First unplug your sharpener, then remove and empty the receptacle. Clean the cutter blades by wiping them off with a dry cloth to remove the residue. Do not use grease, oil or abrasive cleansers. .Never submerge your sharpener in water, plugged or unplugged. .Never pull on the cord to turn the sharpener off. Instead, take hold of the plug and pull it slowly out of the outlet. .As with all electrical appliances, keep out of the reach of small children. .This power unit is intended to be correctly orientated in a vertical or floor mount position.
7 Year Limited Warranty - U.S.A. and Canada Only Effective December 1, 2005 Bostitch ® L.P. warrants to the original retail purchaser that the product purchased is free from defects in material and workmanship, and agrees to repair or replace, at Bostitch’s option, any defective Stanley Bostitch ® branded office product (7) years from date of purchase. Warranty is not transferable. Proof of purchase date required. This warranty covers only damage resulting from defects in material or workmanship; it does not cover conditions or malfunctions resulting from normal wear, neglect, abuse, accident or repairs attempted or made by other than our national repair center or authorized warranty service centers. Driver blades, sharpener cutters, punch heads, and cutting discs are considered normally wearing parts. You are responsible for the costs of shipping the defective product to Stanley Bostitch ® or its designated repair center. For optimal performance of your Stanley Bostitch ® products, always use genuine Stanley Bostitch ® staples and replacement parts. THIS WARRANTY IS THE EXLCUSIVE WARRANTY OF BOSTITCH ® L.P., AND IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. BOSTITCH ® L.P. SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and countries do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state and country to country. For information on our warranty claim procedure please visit us at www.BostitchOffice.com or contact us at 1-800-343-9329. In Canada, please contact us at 1-800-567-7705.
Page 2 of 2 · End of manual
Quick start
- Plug in: Insert the AC plug into the nearest, easily accessible 120-volt outlet.
- Check the receptacle: Make sure the receptacle is in place and tightly closed before you use the sharpener.
- Insert a pencil: Put the pencil into the opening. The motor starts on its own.
- Listen for the change: The TipSaver feature shows the pencil is sharp by a change in motor sound and less resistance. Do not force the pencil further.
- Remove the pencil: Take the sharpened pencil out to prevent motor damage.
- Empty the receptacle: Unplug the sharpener first, then empty the receptacle on a regular basis.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Sharpener does not work properly | The receptacle is full. | Unplug the sharpener, then empty the receptacle. Empty it on a regular basis. Page 2 |
| Sharpener does not run or stops | The receptacle is not in place or not tightly closed. | Make sure the receptacle is in place and tightly closed before you use the sharpener. Page 2 |
| Cutters are clogged | Crayons, chalk, or soft waxy pencils were sharpened. | Unplug the sharpener, remove and empty the receptacle, and wipe the cutter blades with a dry cloth. Do not use grease, oil, or abrasive cleansers. Page 2 |
| Risk of motor damage | The pencil was left in the unit or forced in too far. | Do not force the pencil further once the motor sound changes. Remove the sharpened pencil. Page 2 |
| Cord or plug damage risk | The cord was pulled to turn the unit off. | Take hold of the plug and pull it slowly out of the outlet. Never pull on the cord. Page 2 |
Frequently asked questions
How do I know the pencil is sharp?
The TipSaver feature changes the motor sound and the pencil meets less resistance. Do not force the pencil any further. See page 2.
What power does this sharpener use?
It plugs into a 120-volt outlet. See page 2.
Can I sharpen crayons or soft waxy pencils?
No. Crayons, chalk, and soft waxy pencils clog the cutters. See page 2.
How do I clean the cutters?
Unplug the sharpener, remove and empty the receptacle, then wipe the cutter blades with a dry cloth. Do not use grease, oil, or abrasive cleansers. See page 2.
How long is the warranty?
The warranty is 7 years from the date of purchase, for the U.S.A. and Canada only. Proof of purchase date is required. See page 2.
