T300 Total Trimmer 40" Material Cutter from Logan Graphics Instruction Manual, page 1

Page 1 of 5

T300 Total Trimmer 40" Material Cutter from Logan Graphics Instruction Manual, page 2
Text on page 2

General Purpose Trimmer

The Logan Trimmer offers many unique features and durability that make it the best value trimmer/cutter available. Capable of handling your most demanding trimming needs, the Total Trimmer is the versatile work-horse trimmer you have been looking for. Ideal for trimming difficult materials like PVC foamboard and vinyl, it also easily cuts common materials such as films, paper and almost any flexible or rigid materials. Easy to use, ergonomic design, safety features and inexpensive cost makes the Total Trimmer a cutter with great features at a great price.

For advice, assistance or replacement parts please contact us at www.logangraphic.com

For best results use only authentic Logan blades

CAUTION!!

MAT CUTTING BLADES ARE SHARP

Page 2 of 5

T300 Total Trimmer 40" Material Cutter from Logan Graphics Instruction Manual, page 3
Text on page 3

Identification Board

  1. Squaring Arm
  2. Squaring Arm Stop
  3. Lifter
  4. Cutting Head
  5. Cutting Bar
  6. Handle Bar

Head

  1. Blade Knob
  2. Depth Adjustment Knob I. Plunger Pin J. Blade Holder

CAUTION!!

MAT CUTTING BLADES ARE SHARP

Safety

  • Remove blades when servicing machine.
  • Do no place your fingers near blade when using machine.
  • Be sure lifter bar is down when cutting.
  • Do not force cutting head if stuck.

Attaching Squaring Arm & Stop

  1. Use two screws to attach squaring arm to board.
  2. Slide stop on to squaring arm. (Fig. 1)

Blade Installation

  1. With handle bar in down position, pull out plunger pin & rotate blade holder back. Loosen blade holding screw (Fig. 2)
  2. Slide blade into slot under “Blade” label. (Fig. 3)
  3. Tighten screw & rotate blade holder back until plunger pin releases to safety position.

BLADE DEPTH SETTINGS

1 1/8” 3mm 2 3/16 - 1/4” 5-6mm 3 3/8 - 1/2” 9-12mm

Depth Setting

  1. Determine desired depth setting using Blade Depth Settings chart. (Fig. 4)
  2. Rotate depth adjustment knob to desired number setting. (Fig. 5)

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 3 of 5

T300 Total Trimmer 40" Material Cutter from Logan Graphics Instruction Manual, page 4
Text on page 4
  1. Raise cutting bar using lifter arm or raise to full open position. (Fig. 6)
  2. Slide material onto board and against squaring arm. (Fig. 7)
  3. Adjust Stop to desired dimension. (Fig. 8)
  4. Lower Cutting Bar
  5. Slide Cutting Head beyond end of material.
  6. Pivot blade down fully until it locks. (Fig. 9)
  7. Place hand on to cutting handle & pull cutting head down through material until head reaches support bar. (Fig 10)
  8. Upon contact with support bar, the blade holder will automatically release to safety position. (Fig. 11)

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 4 of 5

T300 Total Trimmer 40" Material Cutter from Logan Graphics Instruction Manual, page 5
Text on page 5

Cutting Head Bearings If cutting head is loose or wobbling, tighten three adjustment screws to eliminate the play and improve cut accuracy. (Fig. 12)

Resquare Squaring Arm

  1. Place a carpenter’s square against cutting bar first. Slide against squaring arm and look for gaps between square and squaring arm. (Fig. 13)
  2. Notice which way squaring arm would have to move to eliminate gap.
  3. Remove squaring arm and locate two screws inside side slots. (Fig. 14)
  4. To adjust, move each screw equal but opposite directions. Only adjust a small amount. DO NOT ADJUST Tension Screw - Single screw on opposite side
  5. Retest squareness.

Logan Graphic Products, Inc. (“Logan”) warrants the T300 and T360 Total Trimmer to be free from defects in parts and workmanship for a period of two years from the date of original purchase. Logan warrants that it will either repair or replace, at its sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied. Be advised that any Logan products purchased as “new” from an unauthorized dealer, such as an online auction site or similar, may be void of their warranty.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 5 of 5 · End of manual

Quick start

  1. Attach the squaring arm to the board with two screws and slide the stop onto the arm.
  2. With the handle bar down, pull out the plunger pin, rotate the blade holder back, loosen the screw and slide a blade into the slot under the Blade label. Tighten and rotate back until the pin releases.
  3. Set the depth adjustment knob using the blade depth chart.
  4. Raise the cutting bar, slide the material against the squaring arm and set the stop.
  5. Lower the cutting bar, slide the cutting head past the end of the material and pivot the blade down until it locks.
  6. Pull the cutting head down through the material; the blade holder releases to the safety position at the support bar.

Troubleshooting

ProblemLikely causeFix (from the manual)
Cutting head is loose or wobblesPlay in the cutting head bearingsTighten the three adjustment screws to remove play and improve cut accuracy. Page 5
Cuts are not squareSquaring arm out of squareCheck with a carpenter's square, remove the squaring arm and move the two screws in the side slots equal but opposite amounts. Do not adjust the single tension screw. Retest. Page 5

Frequently asked questions

What blade depth setting should I use?

Setting 1 is for 1/8" (3mm), setting 2 for 3/16-1/4" (5-6mm) and setting 3 for 3/8-1/2" (9-12mm) materials (page 3).

What materials does the T300 cut?

It is designed for PVC foamboard and vinyl and also cuts films, paper and most flexible or rigid materials (page 2).

What warranty does the Logan T300 have?

Logan warrants the T300 and T360 against defects in parts and workmanship for two years from the original purchase date (page 5).

Which blades should I use?

Logan recommends using only authentic Logan blades for best results (page 2).