Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 1

Page 1 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 2
Text on page 2
  • * * IMPORTANT . * In getting acquainted with your HEP-24OIHEPB-240, it is recommended that you use blank or useless paper before the actual job to be punch ed. That will avoid any unnecessary pressure of failure while learning an unfamiliar procedure.

Your HEP-240/HEPB-24p, have been designed for easy operation. but there are certain techniques and methods to simplify operation while improving your skill as an operator. These instructions will help you in developing your punching efficiency. Read them carefully and become familiar with them.

  • * * POWER: 11 5VAC. 90W. (or 220V, 50-60HZ).

PHASE: SINGLE PHASE.

Page 2 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 3

Page 3 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 4

Page 4 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 5

Page 5 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 6

Page 6 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 7

Page 7 of 8

Tamerica 240EPB Heavy Duty Electric Comb Binding Machine Instruction Manual, page 8

Page 8 of 8 ยท End of manual

Quick start

  1. Practice first: Use blank paper the same size as your pages to learn the machine and find the number of holes and spacing.
  2. Check the power: The machine is rated 115VAC, 90W, single phase. A 220V, 50-60Hz version is also listed.
  3. Set the side guide: Place a test sheet on the Alignment Scale, centered on the right number of white rectangles with at least a 1/8 inch margin at each end. Move the Side Guide flush with its left edge.
  4. Pull set pins: If an edge of the test sheet partly covers a white rectangle, pull out the set pin for that rectangle.
  5. Set the depth: Choose the Depth Guide position from the chart based on paper thickness and binding size. Do not choose a depth that is too deep.
  6. Punch: Insert the sheets flush against the Side Guide and Back Guide Bar, then press the Foot Pedal for one punch cycle. Punch no more than 25 sheets of ordinary stock at a time.
  7. Bind (HEPB-240 only): Pick a plastic binding 2 to 3 mm larger than the paper stack, hang it on the binding fingers, open it with the Master Arm, load the pages and pull the arm back to close.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine cannot punch all the way throughToo many sheets were inserted, or the material is unusually tough.Withdraw the material from the punch throat and reduce its thickness before punching again. Page 5
Feathered edge holes or excess stress on the machineToo many or too heavy sheets punched at once.Punch no more than 25 sheets of ordinary stock at a time and use fewer for heavy or hard to punch paper. Page 4
Partial hole at the edge of the sheetA white rectangle is partly covered by the edge of the sheet.Pull out the set pin that matches the partly covered rectangle so that punch does not engage. Page 4
Pages will not lie flat or are hard to turnThe punch depth is too deep, or the coil diameter is too small.Choose a shallower depth setting. Use a binding 2 mm to 3 mm larger than the stack, including covers. Too small a coil can make pages tear out. Page 4
Binding tips will not go through the holesThe tips of the binding are not yet through the paper holes.Hold the edges flush and move the papers gently back and forth until the tips go through. Page 6
Covers of a different size punch off centerCovers that differ in size need their own guide setting.Punch the covers separately and adjust the Side Guide slightly for the size difference. Page 4

Frequently asked questions

How many sheets can the Tamerica 240EPB punch at once?

Do not punch more than 25 sheets of ordinary stock at one time. The right number depends on paper weight and finish. See page 4.

How do I empty the punch waste?

Slide the chip tray drawer fully out from the rear of the machine, empty it, and put the drawer back. See page 5.

How do I pick the right plastic binding size?

The coil diameter should be 2 mm to 3 mm (1/16 to 1/8 inch) larger than the stack thickness including covers. The ring number should match the number of holes punched. See page 5.

What power does the machine use?

It is rated 115VAC, 90W, single phase. A 220V, 50-60Hz rating is also listed. See page 2.

Does this machine bind as well as punch?

The binding section applies to the HEPB-240 model only. The binding steps are covered in the manual. See page 5.