Page 1 of 3
Text on page 2
Operating Instructions
Important Safeguards
When using clectrical appliances, basie precautions should always be followed to reduce the nisk of electrie shock and injury to pcoplc, including ihe following: I. Read all instructions.
- Always unplug the appliance when not in use or hefore cleaning.
- Do not use oultdoous.
- Extreme cautian should bc taken wlien the appliance is used by or ncar children or
- To protect against risk of electrical hazards, do not immerse cord, plugs. or appliances int walcr or other liqjuids.
- Do not operate the appliance with a danaged cord or plug. vr aier the appliance malfunelions, has heen droppcd or is damagcd in any imanmer. Return appliance to the nearest authorizcd service facility for examination, repair, or adjustment.
- IDo not use acccssory attachments not recommended or sold by thc appfiance
- Do not let cord hang over edge of counter, or touch hot surfaces.
- Do not usc the appliunee for other than intended use. This appliatcc is intcnded for Office or Houseliold use only.
Location
Please remove the laminator carefully from the transit packaging, place the machine oll a flat work surfacc. Loeate the machine in the area where it witl normally be lscd cusuning adequate room for the finishicd laminatc lo feed out at the back.
How To Use
- Plug into the nearcst Ac: ouilet and tum on the power switch.
- Tunn on thic hcaler switch and the red light will glow.
- Delermine the correct temperature setting for your document anrl pouchl comhination. The table below gives some common settings for typical uses:
Recommended Temperatlrl Sltting
Tihickness O1
Pouches
Iu Mil (2S0 Micronj
Page 2 of 3
Text on page 3
- The machine will pre-heat for approximately 3 to 5 minutes. When ready to use. the ready light (yellow light) will glow.
- Prepare your document to be laminated. Allow a minimum 3 mm (1/8") border to ensure good sealing. The machine can be used either with or without a protective
- Turn on the motor switch and the green light will glow.
- When the machine is ready, gently insert the loaded pouch (the closed end of the sleeve) into the entrance slot on the laminator until the pouch is engaged in the
- Allow the laminated item to lie flat and cool under a flat weight. If handled before the adhesive cools, the pouch may become distorted.
- If the lamination is not clear, please increase the temperature by 5~ 10°C and then process the pouch a second time. If the lamination is waved, please reduce the temperature by 5~ 10°C wait 2 minutes and then process the next lamination.
- Turn off the motor switch, heater switch and power switch after use.
Care And Cleaning
- This appliance is for Office or Household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service
- Do not immerse in water.
- To reduce the risk of fire or electric shock, do not remove the base. No user serviceable parts inside.
- Keep your hands and cord away from hot parts of the appliance during operation. . Never clean with scouring powders or hand implements. . Wipe clean with a soft cloth.
Page 3 of 3 · End of manual
Quick start
- Place the machine: Put it on a flat work surface with room at the back for the finished laminate to feed out.
- Power on: Plug it into an AC outlet and turn on the power switch. Then turn on the heater switch and the red light glows.
- Set temperature: Choose the temperature setting for your document and pouch using the table in the manual.
- Pre-heat: The machine pre-heats for about 3 to 5 minutes. The yellow ready light glows when it is ready.
- Prepare the document: Leave a minimum 3 mm (1/8 inch) border so the pouch seals well. Turn on the motor switch and the green light glows.
- Feed the pouch: Gently insert the loaded pouch, closed end first, into the entrance slot until it is engaged.
- Cool and shut down: Let the laminate cool flat under a flat weight. After use, turn off the motor, heater, and power switches.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Lamination is not clear | The temperature is too low. | Raise the temperature by 5 to 10 degrees C and run the pouch a second time. Page 3 |
| Lamination is waved | The temperature is too high. | Lower the temperature by 5 to 10 degrees C, wait 2 minutes, then run the next lamination. Page 3 |
| Laminated item is distorted | It was handled before the adhesive cooled. | Let the item lie flat and cool under a flat weight. Page 3 |
| Pouch does not seal well | The document has no border. | Leave a minimum 3 mm (1/8 inch) border. Page 3 |
| Cord or plug is damaged, or the machine was dropped | The appliance may be damaged. | Do not operate it. Return it to the nearest authorized service facility. Page 2 |
Frequently asked questions
How long does the TCC160 take to pre-heat?
About 3 to 5 minutes. The yellow ready light glows when it is ready. See page 3.
What border should I leave around the document?
Leave a minimum 3 mm (1/8 inch) border for a good seal. See page 3.
What if the lamination is not clear?
Raise the temperature by 5 to 10 degrees C and process the pouch a second time. See page 3.
What if the lamination is waved?
Lower the temperature by 5 to 10 degrees C, wait 2 minutes, then process the next one. See page 3.
How do I clean the laminator?
Wipe it clean with a soft cloth. Do not use scouring powders or hand implements, and do not immerse it in water. See page 3.
