Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 1

Page 1 of 6

Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 2

Page 2 of 6

Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 3

Page 3 of 6

Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 4

Page 4 of 6

Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 5

Page 5 of 6

Tamerica TCC 2700 27" Roll Laminator Instruction Manual, page 6

Page 6 of 6 · End of manual

Quick start

  1. Place the machine: Set it on a flat work surface. Leave room at the back for the finished laminate to feed out.
  2. Load the film: Remove the feed tray. Slide the roll of film onto the upper and lower rods, with equal rod length showing at each end. Put the rods in the laminator.
  3. Thread the film: Follow the threading card that comes with the film. Pull the handle forward to release roller pressure, then push the film through the rollers. Keep the film aligned top and bottom, then replace the feed tray.
  4. Heat up: Turn on the power switch and set the temperature with the TEMP/SET keys. The lowest setting is 90°C (194°F). Press the HOT key to start heating.
  5. Set the speed: Use the MOTOR keys to set the speed. For 3 mil film the manual lists 110°C (230°F) at speed 3.
  6. Check the tension: Turn each supply roll by hand. Use the adjusting knob so the top and bottom rolls feel equally tight.
  7. Finish up: Press the COOL key when done. Keep the motor running until the rolls are below 50°C (122°F), then turn the machine off.

Troubleshooting

ProblemLikely causeFix (from the manual)
Film leaves residue on the hot roll and pull rollsThe top and bottom film overlapped when it was threaded.Re-thread with the handle pulled forward. Make sure the film is perfectly aligned top and bottom. Follow the threading card. Page 2
Laminated sheets curl up or downThe top and bottom supply rolls have unequal tension. Curling up usually means the top roll is tighter. Curling down usually means the bottom roll is tighter.Turn the adjusting knob clockwise to increase tension or counter clockwise to decrease it, until both rolls are even. Page 4
A document is jamming or may be damaged in the machineThe document is stuck in the rollers.Press the REVERSE key to pull the document back out. Page 4
Screen shows ER1The thermometer inside the machine is damaged. The machine shuts off to protect itself.Contact your vendor or dealer. The manual says a PC board replacement may be needed. Page 4
Screen shows ER2The machine kept heating for over 12 minutes. It shuts off automatically.Contact your vendor or dealer. The manual says a PC board replacement may be needed. Page 4
Screen shows ER3 and the buzzer soundsThe machine temperature went above 200°C (392°F). It shuts off automatically.Contact your vendor or dealer. The manual says a PC board replacement may be needed. Page 5

Frequently asked questions

What is the lowest temperature I can set?

The lowest setting is 90°C (194°F). The display shows your set temperature for 3 seconds, then the actual temperature. See page 3.

What size film roll does it take?

It uses roll film with a 1 inch core and a maximum width of 690mm (27 inches). See page 4.

Why did the machine stop on its own?

If the motor speed is not adjusted and the machine is left alone, it stops after about 3 minutes. This protects the hot rollers, which must keep turning while heated. See page 3.

How do I pause laminating without turning the machine off?

Push the handle forward to release the hot and pull rolls, and the film stops running. Pull the handle back to start laminating again. See page 4.

How do I clean the laminator?

Unplug it and wipe it with a soft cloth. Do not use scouring powders or hand implements, and do not put it in water. See page 5.