The Sterling Digibinder Plus Operator's Manual, page 1
Text on page 1

The Sterling Digibinder ®

Operator’s Training Manual

Issue 1 October 1, 2013

This manual is for both versions of the Sterling Digibinder and Sterling Digibinder Plus.

The Digibinder Plus sits on its own stand/cabinet which houses both the air compressor and the dust extractor. To turn on the Dust Extractor, locate the toggle switch on the front of the machine.

You can bypass the safety hood’s sensor by using the supplied key(s) located near the Dust Extractor switch.

Page 1 of 53

The Sterling Digibinder Plus Operator's Manual, page 2
Text on page 2

Table of Contents

GETTING STARTED .................................................................................................................. 3

POWERING UP ........................................................................................................................ 7

CONTROL PANEL ..................................................................................................................... 7

SETTING UP THE DIGIBINDER ................................................................................................. 8

SETTING THE CLAMP LIMITER ......................................................................................................... 9

ALIGNING THE COVER STOCK ......................................................................................................... 10

BOOK THICKNESS WHEEL & NIPPER ADJUSTMENT KNOB ............................................................. 10

SIDE GLUE ADJUSTMENT ................................................................................................................ 11

ADJUSTING THE STRENGTH OF THE BIND ..................................................................................... 12

GETTING INTO PRODUCTION ............................................................................................... 13

MAKING PADS ...................................................................................................................... 13

DRAINING THE GLUE ............................................................................................................. 13

DAILY MAINTENANCE ........................................................................................................... 14

WEEKLY MAINTENANCE ....................................................................................................... 14

TROUBLESHOOTING ............................................................................................................. 15

UNEVEN OR INCONSISTENT SIDE GLUE ........................................................................................... 15

ADJUSTING SIDE GLUE BETWEEN HEAD AND FOOT OF BOOK ......................................................... 15

ADJUSTING SIDE GLUE ON OPERATOR AND NON‐OPERATOR SIDES OF THE BOOK ......................... 16

PAGES NOT BINDING WELL............................................................................................................. 16

ROUGHING BLADE AND NOTCHING PINS ADJUSTMENT .................................................................. 17

UNEVEN CORNERS ON THE BOOK SPINE ......................................................................................... 18

LEVELING THE NIPPER TABLE .......................................................................................................... 18

MACHINE DOES NOT CYCLE ............................................................................................................ 19

MACHINE BEEPS TWICE IN RAPID SUCCESSION AND DOES NOT CYCLE............................................ 19

CLAMP IS STUCK / ERROR MESSAGE ............................................................................................... 19

Page 2 of 53

The Sterling Digibinder Plus Operator's Manual, page 3
Text on page 3

GETTING STARTED

Congratulations on your purchase of THE STERLING DIGIBINDER or DIGIBINDER PLUS. This machine will allow you to perfect bind any book up to 2 ¼” or 55mm thick.

For the Tabletop version: Before removing the machine from the shipping crate, have a table ready that will support 330 LBS (150 kg). Uncrate the machine and inspect it for any damage that may have occurred during transport. Place the Sterling Digibinder on the table. Use of a lift truck is recommended. Be careful to avoid injury.

Remove the compressor from the box and stand it on a solid surface. Do not place the compressor in an enclosed area such as a cabinet unless it is well ventilated. The air filter should already be installed on the compressor but if not, locate it within the compressor box and install it onto the fitting. (FIG #1) Do not over tighten.

Plug the Digibinder’s power cord and the Air Compressor’s power cord into the back of the Digibinder. (FIG #2)

Page 3 of 53

The Sterling Digibinder Plus Operator's Manual, page 4
Text on page 4

Install the exhaust fan, Start by attaching the connectors. Press the connectors back into the cavity along with any slack of the cord and screw in the exhaust fan. Flip the exhaust box power switch on. (FIG #3)

Plug the Digibinder’s blue air tube and the supplied air gun into the “Y” air splitter then plug the air splitter’s tube into the compressor. (FIG #4)

Page 4 of 53

The Sterling Digibinder Plus Operator's Manual, page 5
Text on page 5

Open the valve on the compressor’s pressure gauge (FIG #5) and flip the toggle switch to the on position. Make sure the bleed valve at the bottom of the compressor is closed (not shown). (FIG #5 ‐ Arrow)

Attach the Tall Book Guide on top of the clamp. (FIG #6)

Install The Front Book Support. (FIG #7)

Page 5 of 53

The Sterling Digibinder Plus Operator's Manual, page 6
Text on page 6

Install the Rear Table Cover Support behind the Nipper Table. (FIG #8)

Screw in the Nipper Adjustment Knob on the front of the Nipper Table. (FIG #9)

Page 6 of 53

The Sterling Digibinder Plus Operator's Manual, page 7
Text on page 7

For the DIGIBINDER PLUS: Use a fork lift to lift the machine off the skid. Keep the machine steady, it is top heavy. Make sure all four wheels have the stops in the up position before placing it on flat level ground. Once the machine has been moved to its final position, lower the stops to prevent the machine from rolling. To install the accessories, follow the previous set of instructions for the Table Top Digibinder. Some parts may already be installed.

POWERING UP

Have your electrician check that your incoming power is 220 volts, single phase, 15 amps. Have your electrician attach a plug onto the end of the Digibinder’s Power Cord that matches your socket.

The Power Switch is located on the right side of the Digibinder. Turn on the Digibinder and check that the screen lights up along with a red LED indicating the gluepot heater is on and working. Make sure the Emergency Stop button is in the up position. If not, give it a gentle twist clockwise to release it.

CONTROL PANEL

(FIG #10)

The keypad controls the functions of the Digibinder for operation, set up or troubleshooting. The following is a list of the control buttons and switches. See the figure below.

  1. START: This will cycle the Digibinder fully through the binding process. This will not function unless there is a book in the clamp and cover stock on the nipper table.
  2. CLAMP: Opens and closes the clamp. Use this feature for setting the clamp to the thickness of your book by utilizing the clamp limiter bar (more on that later).
  3. Green LED: The machine will not cycle until the glue has fully melted and this LED is lit.
  4. UP: Raises the glue temperature or increases the nipper’s finish time.
  5. DOWN: Lowers the glue temperature or decreases the nipper’s finish time.
  6. Red LED: Indicates that the glue heater is on.
  7. X: Clears the functions of the glue rollers, drops and opens the nipper table (if in the up and closed position), resets the batch count and toggles the padding feature on or off.
  8. O: Stand by. Lowers the glue temperature to 130 and prevents any function of the Digibinder.
  • *Also cycles the roughing motor if the Digibinder is in the SET UP Mode.
  1. NIPPER CLOSE: Closes the nipper table. Press X to open.
  2. NIPPER UP: Raises the nipper table. Press X to drop.

Page 7 of 53

The Sterling Digibinder Plus Operator's Manual, page 8
Text on page 8
  1. LEFT: Moves the clamp to the left.
  2. RIGHT: Moves the clamp to the right.
  3. CYCLE GLUE ROLLERS: Use when adding glue. Glue should be approximately ¾” below the top of the gluepot.
  4. SET: Pressing the UP or DOWN arrows on the 1 st screen changes the glue pot temperature. The counter on this screen cannot be reset.

Press SET once for the Padding Mode screen. Press X to toggle padding on or off. Press SET again For the Finish Time. Use the UP or DOWN arrows to set the Nipper Table dwell time. If padding is on, each increment would add 10 seconds. 15 would equal 150 seconds. If padding is off, 15 would equal 4 seconds. Press SET a third time to get to the batch counter. This counter can be reset using the X button. Press SET once more to return to the main screen.

  1. POWER SWITCH: Located on the right side of the machine.
  2. TOGGLE SWITCH: Turns the roughing motor on or off. The toggle switch is located below the Main Power Switch. Leave up for perfect binding or down for making pads.

SETTING UP THE DIGIBINDER

Turn on the Digibinder to warm up the glue pot. The machine will not cycle until the glue has thoroughly melted. This should not take longer than 45 minutes. During this time, the green LED will remain off and you cannot change the settings from the control panel. The temperature will rise above the set value then gradually lower to the set temperature. When the machine is ready, the glue rollers will cycle, the machine will give 3 audible beeps and the green LED will light indicating it is now ready for use. At this time, you may adjust the temperature if needed. We recommend 160 degrees centigrade. The machine will not cycle if the green LED is off (FIG #10, item 3), without a book in the clamp (FIG #11) or cover stock on the nipper table (FIG #12).

Page 8 of 53

The Sterling Digibinder Plus Operator's Manual, page 9
Text on page 9

Put a cover in position on the nipper table placing it square to the right stops with the rear edge tucked under the top stop guide. Loosen the top stop guide and adjust accordingly, depending on the size of the book. The rear of the book’s spine will line up with the scored line in the nipper table. (FIG #13)

SETTING THE CLAMP LIMITER

Place the book block in the open clamp and jog it to the right, then press the CLAMP button. After the clamp closes, move the Limiter Bar’s Pin into the second closest hole to the front, outside of the clamp. This will limit how wide the clamp opens so placing books of the same thickness will be easier and quicker. Press CLAMP again to open the clamp. Check that the clamp’s opening is approximately ¼” wider than the book’s thickness. This will ensure the clamp will not drag the book back after it has been bound. (FIG #14)

Page 9 of 53

The Sterling Digibinder Plus Operator's Manual, page 10
Text on page 10

It is not necessary to continue to use the CLAMP button once the clamp opening is set. Simply place the book inside the clamp and jog it down and to the right so the pages are even. Check that the cover is against both right stops and tucked under the back stop. Make sure the toggle switch below the main power switch is up. Also check that your compressor is on and up to pressure and the pressure gauge’s valve is in the open position.

Keep your hand above the book to prevent any of the pages from “floating” up. The clamp may squeeze air out from between the pages as it closes. Press START to cycle the machine. Lift the book off the nipper table as the clamp retreats. Inspect the book for proper alignment of the cover, even corners of the spine and adequate glue for both sides of the book. Do not open the pages yet. Allow time for the glue to cool and harden.

ALIGNING THE COVER STOCK

To adjust the cover left or right, loosen and move the right stops left or right using caution. THE RIGHT STOPS ARE VERY HOT! Only loosen the hex screw in the center of each stop with the supplied 4mm T‐handle Hex Key. Do not over tighten! To adjust the cover forward or back, loosen and adjust the Top Stop Guide (knob). (FIG #13)

BOOK THICKNESS WHEEL & NIPPER ADJUSTMENT KNOB

The Book Thickness Wheel (Fig #15) adjusts the upward pressure of the nipper table to help produce a flatter spine. For thinner books, turn it left. For thicker books, turn it right. Normally books under ¼” would require a setting of 100 or higher. Half inch books should be set at 70. One inch or thicker should be set at 50 or slightly lower. These are average settings. You may require more or less pressure depending on your stock and covers. You may also make use of the Nipper Adjustment Knob to help produce squarer/sharper corners using the chart on the top plate of the nipper table (Fig #9).

Page 10 of 53

The Sterling Digibinder Plus Operator's Manual, page 11
Text on page 11

Note, setting the nipper adjustment knob too tight may cause some sheets of the book to fold over. Simply open the nipper table further if this occurs. (FIG # 9 and #15)

SIDE GLUE ADJUSTMENT

Keep in mind that the glue pot and everything on it is extremely hot.

Make sure the glue level is within ¾” from the top of the glue pot. Add glue chips as needed. Then try another book before making the following adjustments.

For more side glue on the non‐operator side, loosen and move the Side Glue Wire closer to the rear side of the book. For less side glue, move it further away from the rear side of the book. (FIG #16)

Page 11 of 53

The Sterling Digibinder Plus Operator's Manual, page 12
Text on page 12

For more side glue on the operator side, you may need to adjust the Glue Pot’s Metering roller down. Adjust the metering roller by loosening the set screw with the supplied 3mm t‐handle hex key then placing the tip of the hex key into any of the holes in the nut located near the glue pot’s drive chain. Rotate it towards the left (lower) to apply more glue or towards the right (higher) for less. The Book Thickness Wheel also affects the amount side glue that gets squeezed up. (FIG # 17)

You may want to adjust the Nipper table’s dwell time by pressing the SET button twice until you reach FINISH TIME then press the up or down arrows on the right side of the screen to increase or decrease how long the nipper squeezes the cover on the book. NOTE: If the Padding mode is on, 15 would equal 150 seconds. If the padding mode is off, then 15 would equal 4 seconds. We recommend setting the Finish Time to 15 for perfect binding books and 4 for pads. (More information for making pads is on page 13.)

Allow the book to cool a bit before inspecting it. Check that the side gluing is to your satisfaction inside the front and rear covers. Refer to the troubleshooting section starting on page 14 if these adjustments do not produce side glue to your satisfaction.

ADJUSTING THE STRENGTH OF THE BIND

Before making adjustments to the roughing wheel and/or notching pins, turn off the roughing motor by flipping the toggle switch off. Locate it below the main power switch.

Paper grain direction should follow along the length of the spine. This will add strength to your bind. After the book has sat for an hour, you may check the binding strength. If the pages pull straight out easily, you may need to raise the notching pins or add more glue to the spine by lowering the Metering Roller or adjusting the Book Thickness Wheel. The Roughing Wheel should not need to be adjusted. They are set to rough, not cut the pages. The Notching Pins can be set higher for certain heavier/glossier stock that tends to repel the glue. When raising the Notching Pins, do not allow them to cut more than 1/16 ” into the

Page 12 of 53

The Sterling Digibinder Plus Operator's Manual, page 13
Text on page 13

book. Also make sure they do not hit the guards. Please refer to the troubleshooting section starting on page 14 for more details.

GETTING INTO PRODUCTION

Once the settings are to your satisfaction place the next book body into the clamp, jog it down and toward the right. Place the cover stock squarely on the nipper table with the rear edge tucked under the Top Stop Guide. Then simply press START.

If you have a DIGIBINDER PLUS, turn on the Vacuum motor by flipping the green toggle switch on the front of the machine.

MAKING PADS

If you are making pads, be sure to flip the toggle switch below the main power switch down to turn off the roughing motor. Press the SET button for the PADDING MODE screen then press X to toggle it on or off. Padding On will disable the Nipper Table and the cover stock sensor. Press SET again then Up or DOWN arrows to set the length of the finish time. NOTE: If the Padding mode is on, 15 would equal 150 seconds. If the padding mode is off, then 15 would equal 4 seconds. Press SET twice to return to the temperature screen. TIP: If you prefer using the nipper table for pads, leave the padding feature off and block the sensor on the nipper table. Use of any non‐stick spray is recommended to prevent glue from sticking to the table. *Do not make pads while using iGlue.*

DRAINING THE GLUE

After a period of time, the glue may get dirty or burnt or you may need to change the type of glue you are using. To drain the glue, remove the front panel, being careful not to damage the control panel wires, to locate the drain. Place a box under the drain chute and remove the Allen screw. USE CAUTION: Drain chute, Allen screw and glue are extremely hot! When the glue has been drained you may melt wax in the glue pot to remove any excess glue and clean out any paper dust at the bottom. (FIG #18)

Page 13 of 53

The Sterling Digibinder Plus Operator's Manual, page 14
Text on page 14

DAILY MAINTENANCE

The glue level in the pot will go down as books are bound. Glue chips should be used to replenish the pot as needed. If you see a dry spot or large air pocket on the center glue roller, add more glue. The level of the glue should rise to about 3/4” below the top of the glue pot.

Do not leave the machine powered on when not in use. This will cause the glue to burn and darken. If reheating is too time consuming, press the O button on the control panel to put the machine into Stand‐By mode. This will lower the glue temperature to prevent burning. Press O again to resume.

Use the supplied air gun to blow paper dust away from the glue pot.

The front and rear shafts must be cleaned regularly to allow smooth operation of the clamp. Solvents or penetrating oils may be used to remove any glue residue. The shafts must be clean and slick so the clamp doesn’t get bogged down or stuck during operation.

WEEKLY MAINTENANCE

Check that the Notching Pins are sharp to avoid straining of the roughing motor and to ensure clean notching for adequate glue penetration. When replacing dull Notching Pins, follow the instructions in the Troubleshooting Section of this manual under ROUGHING BLADE & NOTCHING PIN ADJUSTMENT.

Page 14 of 53

The Sterling Digibinder Plus Operator's Manual, page 15
Text on page 15

Air Compressor: The compressor should be bled weekly to remove moisture build up inside the tank. The bleed valve is located at the bottom of the compressor tank. Check the oil level in the sight glass of the compressor motor. If oil is not visible or low, add air compressor oil into the motor’s tube by removing the rubber cap (opposite side from the filter). Also check that the filter isn’t clogged. To avoid overheating, do not operate the compressor in an enclosed area and check for air leaks periodically. Make sure the compressor is off when not in use.

TROUBLE SHOOTING

Some adjustments require the Digibinder to be in the SETUP mode. This is done by turning off the Digibinder then, while holding down the CLAMP button, turn the power back on.

  • *Note: The machine will cycle continuously if the START button is pressed. Press and hold the X button while the clamp is traveling to the right to stop the cycling or press the Emergency Stop button. Also, while in Setup Mode, the O (Stand By) button will turn on the roughing motor. Pressing the X button will stop the motor. Flip the toggle switch below the Main Power Switch to turn off the Roughing Motor. CAUTION: Pressing the RIGHT arrow button will close the roughing blade guard. To reset the machine back to normal operation, simply turn the machine off then on again.

UNEVEN OR INCONSISTENT SIDE GLUE

Make sure the glue pot has enough glue. While the rollers aren’t cycling, the glue level should be about ¾” below the top of the glue pot. Check that the Air Compressor is on and up to pressure. There should be between 90 – 110 psi. You may also need to level your nipper table. See Leveling the Nipper Table on page 16.

ADJUSTING SIDE GLUE BETWEEN HEAD AND FOOT OF BOOK

  1. Put the Digibinder in SETUP Mode. The clamp will close and the roughing blade's guard bracket will open.
  2. Open the clamp and place a cover sheet in it, making sure the bottom doesn’t curl as the clamp closes. Close the clamp then jog it, using the left and right arrow buttons, back and forth over the Glue Pot’s Metering roller. Check the distance from the bottom of the cover stock to the roller. The cover stock must be the same distance above the roller from the leading edge to the trailing edge.

Page 15 of 53

The Sterling Digibinder Plus Operator's Manual, page 16
Text on page 16
  1. Locate the screws on the topside of the register table where you place the books. Level one end of the register table by turning the screws clockwise to lower or counterclockwise to raise it using a 5mm hex key.
  2. Reset the machine back to normal operation simply by turning the machine off then on again after completing adjustments, then test by binding a book. If the table is leveled but the side gluing still isn't even, you may need to level the nipper table. See Leveling the Nipper Table below.

ADJUSTING SIDE GLUE ON OPERATOR AND NON‐OPERATOR SIDES OF THE BOOK CAUTION: Burn Hazard.

Because the rear nipper table comes in before the front table does, more glue is channeled towards the front of the book. Adjust the Metering roller until you have enough side glue between the cover and the 1st page of the book (operator side). Then locate the side glue wire on top of the far right glue roller. Press the Emergency Stop button. Loosen the screw then, using a pair of needle nose pliers, move the Side Glue Wire slightly closer to the book to apply more or further away for less side glue between the cover and last page (non‐ operator side) of the book. Release the Emergency Stop button by giving it a gentle twist clockwise.

PAGES NOT BINDING WELL

The glue needs time to cool and harden. Let them sit an hour before checking the binding strength. If the pages still come out too easily then it may need deeper roughing and/ or notching, more glue, more nipper pressure, a longer nipper dwell time or special glue for your product.

TIP: The grain direction of the paper and cover stock should follow the length of the book’s spine. This will improve the binding strength by as much as 25%. Fold the stock in half, length wise then width wise, and see which fold looks cleaner/smoother. The smoother fold is the grain direction. You may also try one of these other solutions:

  1. Increase the nipper finish time. Press the SET button twice to get to the Finish Time screen. Use the UP arrow button to increase the Finish Time.
  2. Increase the nipper pressure by slightly turning the book thickness wheel to the left. Be sure not to use too much pressure. This will squeeze out the glue from the spine or cause “nail heading”.
  3. Increase the amount of glue being applied by lowering the far left glue metering roller.

The glue level in the pot will go down as books are bound. Glue chips should be used to

Page 16 of 53

The Sterling Digibinder Plus Operator's Manual, page 17
Text on page 17

replenish the pot as needed. If you see a dry spot or large air pocket on the center glue roller, add more glue. The level of the glue should rise to about 3/4” below the top of the glue pot.

  1. Pull a page out of the book and check the depth of the notches. If they are barely visible then you need to raise the notching pins. Adjust the roughing and notching. (See Roughing Blade and Notching Pin Adjustment below) Heavier stock or coated materials need deeper notching and a longer nipper finish time. *Note: Notching pins must be sharp!

ROUGHING BLADE AND NOTCHING PINS ADJUSTMENT

  1. Remove the operator side guard from the top of the roughing blade.
  2. Put the Digibinder in SETUP mode as described at the beginning of this Troubleshooting section. Turn off the Roughing motor by flipping the toggle switch below the main power switch.
  3. Remove the front panel/guard. Be careful not to pull the wires of the display/control panel board.
  4. Open the clamp and place a cover sheet in it, making sure the bottom doesn’t curl as the clamp closes. Close the clamp then jog it over the roughing blade using the left and right arrow buttons. Press the Emergency Stop Button.
  5. Loosen the setscrews locking the roughing blade assembly to the motor's shaft (under the blade assembly) with the supplied T‐handle hex key. (FIG #18)
  6. Adjust the roughing blade's height so that the tips of each tooth just lightly touch the pages. Lock the setscrews once the correct height is set.

Page 17 of 53

The Sterling Digibinder Plus Operator's Manual, page 18
Text on page 18
  1. Adjust the notching pins so that it goes no more than 1/16" into the pages. Loosen setscrews on the outside of the roughing blade assembly with a 2.5mm hex key. You may need to raise it a bit more for heavier or coated stock. *Note: The notching pins may fall out once the setscrews are loosened. (FIG #19)
  2. Install the blade’s guard and check that the roughing blade and notching pins do not interfere with the guards by turning the blade by hand.
  3. When you are done making adjustments, turn the machine off then on again to return it to normal operation. Install all guards and release the Emergency Stop button.

UNEVEN CORNERS ON THE BOOK SPINE

Make sure the compressor is turned on, up to pressure and the Air Compressor’s valve where the machine's air hose is connected is in the fully open position. Make sure the bleed valve at the bottom is fully closed. The pressure gauge's needle should point approximately .75 MPa or 110 PSI (between 11 and 1 o’clock). Make sure the air hose isn't pinched or kinked.

If you have the correct air pressure and the corners still aren't even, then you may need to level the nipper table. If one or both ends of the book have very sharp corners, try lowering the book thickness wheel a bit.

LEVELING THE NIPPER TABLE

  1. Press the 1st and 2nd buttons on the control panel (top left buttons) to raise and close the nipper table. Remove the small front white cover stock support tray.
  2. Remove Rear Table Cover Support only if you need to adjust the rear right side of the nipper table. You can adjust the rear setscrew on the left side without removing this tray.

Page 18 of 53

The Sterling Digibinder Plus Operator's Manual, page 19
Text on page 19
  1. Loosen 2 locking screws at the corner you want to adjust with the supplied 4mm T‐handle hex key.
  2. Turn the adjustment setscrew with a 2.5mm hex key clockwise to raise or counterclockwise to lower that corner. *Note: You should adjust the front and rear (operator and non‐operator side) set screws the same amount on either the left or right side of the nipper table. When lowering a corner, press down slightly on that corner while tightening the two 4mm locking screws. (FIG #19)

MACHINE DOES NOT CYCLE

Make sure the machine is up to temperature and the green lamp on the control panel is lit. It takes approximately 45 minutes to reach operating temperature before it will allow you to operate.

Check that the Set temp and actual temp are over 130 degrees Celsius.

MACHINE BEEPS TWICE IN RAPID SUCCESSION AND DOES NOT CYCLE

Make sure the book is in the clamp and a cover sheet is on the nipper table and both are jogged all the way to the right and blocking the sensors. Some dark stocks may not activate the sensor(s).

CLAMP IS STUCK / ERROR MESSAGE

Most problems can be solved over the phone but you may need to schedule a service call. Write down the error message and machine serial number and call your dealer.

The front and rear shafts must be clean and slick or the clamp will get stuck. It is recommended that you clean the shafts daily. You may use solvents or penetrating oil to clean any paper dust or glue residue from the shafts. CLEAN THE SHAFTS DAILY.

Page 19 of 53

The Sterling Digibinder Plus Operator's Manual, page 20

Page 20 of 53

The Sterling Digibinder Plus Operator's Manual, page 21

Page 21 of 53

The Sterling Digibinder Plus Operator's Manual, page 22

Page 22 of 53

The Sterling Digibinder Plus Operator's Manual, page 23

Page 23 of 53

The Sterling Digibinder Plus Operator's Manual, page 24

Page 24 of 53

The Sterling Digibinder Plus Operator's Manual, page 25
Text on page 25

Tachoplus Code 77.1010 77.1015 77.1020 77.1030 77.1040

Description Screw for outlet Outlet nut Glue outlet Heater Plate Temperature sensor cpl.

Page 25 of 53

The Sterling Digibinder Plus Operator's Manual, page 26
Text on page 26

Tachoplus Code 77.1080 77.1090 77.1100 77.1120

Description Main chain Glue pot chain Height control handle chain Main chain connecting supporter

Page 26 of 53

The Sterling Digibinder Plus Operator's Manual, page 27
Text on page 27

Tachoplus Code 77.1130 77.1140 77.1150 77.1160 77.1165 B770820

Description EL 1/8-6(ROHS) Filter Solenoid valve Sensor clamp Sensor clamp cable 196cm Solenoid valve Set

Page 27 of 53

The Sterling Digibinder Plus Operator's Manual, page 28
Text on page 28

Tachoplus Code 77.1170 77.1190 77.1200 77.1310

Description Slide bearing cpl. Nipping plate front Right vice cylinder Nipping plate back

Page 28 of 53

The Sterling Digibinder Plus Operator's Manual, page 29

Page 29 of 53

The Sterling Digibinder Plus Operator's Manual, page 30

Page 30 of 53

The Sterling Digibinder Plus Operator's Manual, page 31
Text on page 31

Tachoplus Code 77.1250 77.1260 77.1270 77.1280 77.1290 77.1300 77.1350

Description Doctor roller scraper Middle glue roller scraper cpl. Side glue guide First glue roller Middle glue roller Doctor roller Relay, high voltage

Page 31 of 53

The Sterling Digibinder Plus Operator's Manual, page 32

Page 32 of 53

The Sterling Digibinder Plus Operator's Manual, page 33

Page 33 of 53

The Sterling Digibinder Plus Operator's Manual, page 34
Text on page 34

Tachoplus Code 77.1601 77.1611 77.1630

Description LCD panel Display data cable(NEW) Gear f. table height adjustment

Page 34 of 53

The Sterling Digibinder Plus Operator's Manual, page 35
Text on page 35

Tachoplus Code 77.1725 77.1730 77.1740

Description Panel unit (new Ver) Set of end Step Switches Main motor(S9R40GXH-CE)

Page 35 of 53

The Sterling Digibinder Plus Operator's Manual, page 36

Page 36 of 53

The Sterling Digibinder Plus Operator's Manual, page 37
Text on page 37

Tachoplus Code 77.1830 77.1840 77.1850 77.1860 77.1865 B771940

Description Sensor cover (left) Back stop assy cpl. Air pistol Paper guide plate Power cord Wrench Set

Page 37 of 53

The Sterling Digibinder Plus Operator's Manual, page 38

Page 38 of 53

The Sterling Digibinder Plus Operator's Manual, page 39
Text on page 39

Tachoplus Code 77.1971 77.1980 77.2020 B770910

Description Main switch Switch for slitting tool End stop spring cpl. Main Switch tool

Page 39 of 53

The Sterling Digibinder Plus Operator's Manual, page 40
Text on page 40

Tachoplus Code 77.2050 77.2070 77.2080 77.2090 77.2120 77.2170

Description Exhauster Safety device sensor bar Safety device PCB Connection sensor Bar to PCB On/off-switch for exhauster Safety hood

Page 40 of 53

The Sterling Digibinder Plus Operator's Manual, page 41

Page 41 of 53

The Sterling Digibinder Plus Operator's Manual, page 42

Page 42 of 53

The Sterling Digibinder Plus Operator's Manual, page 43

Page 43 of 53

The Sterling Digibinder Plus Operator's Manual, page 44

Page 44 of 53

The Sterling Digibinder Plus Operator's Manual, page 45
Text on page 45

When ordering notching pins or a roughing blade, indicate the model and serial number of your machine.

Tachoplus Code 77.7140 77.7150 77.7160

Description Slit/fan housing box Slit tool Dusty filter

Page 45 of 53

The Sterling Digibinder Plus Operator's Manual, page 46

Page 46 of 53

The Sterling Digibinder Plus Operator's Manual, page 47

Page 47 of 53

The Sterling Digibinder Plus Operator's Manual, page 48
Text on page 48

Tachoplus Code 77.7260 77.7270 77.7280

Description Dusty gear board Brush fixing board Scarping cover cylinder fixing bracket

Page 48 of 53

The Sterling Digibinder Plus Operator's Manual, page 49

Page 49 of 53

The Sterling Digibinder Plus Operator's Manual, page 50

Page 50 of 53

The Sterling Digibinder Plus Operator's Manual, page 51

Page 51 of 53

The Sterling Digibinder Plus Operator's Manual, page 52
Text on page 52

Tachoplus Code 77.8120 77.8130 77.8140 77.8150

Description Safety cover handle Cover fixing pin (right) Cover fixing pin (left) Safety cover sensor

Page 52 of 53

The Sterling Digibinder Plus Operator's Manual, page 53
Text on page 53

Tachoplus Code 77.8240 77.8250 77.8500 77.8510

Description Main chain gear fixing board Safety key switch Front cover case Front cover case fixing ring

Page 53 of 53 ยท End of manual

Quick start

  1. Have an electrician confirm 220 volts, single phase, 15 amps and fit a matching plug. Connect the compressor and air splitter and open the compressor valve.
  2. Turn on the power switch on the right side and make sure the Emergency Stop is released.
  3. Wait for the glue to melt (up to 45 minutes). When ready the machine beeps 3 times and the green LED lights. 160°C is recommended.
  4. Place a cover on the nipper table square to the right stops with the rear edge under the top stop guide, lined up with the scored line.
  5. Put the book block in the clamp, jog it right, press CLAMP, and set the limiter pin so the clamp opens about 1/4" wider than the book.
  6. Set the Book Thickness Wheel (about 100+ for books under 1/4", 70 for 1/2", 50 or lower for 1" and up).
  7. With the roughing toggle switch up and the compressor at pressure, hold the pages down and press START. Let the glue cool before opening the book.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not cycleThe glue is not up to temperature, so the green LED is off.Allow about 45 minutes to reach operating temperature and check that set and actual temperatures are over 130°C. Page 19
Machine beeps twice rapidly and does not cycleThe book or cover sheet is not blocking its sensor; some dark stocks may not activate the sensors.Make sure a book is in the clamp and a cover is on the nipper table, both jogged fully right over the sensors. Page 19
Clamp is stuck or shows an error messageDirty front and rear shafts, or a machine fault.Clean the shafts daily with solvent or penetrating oil. If the error persists, note the message and serial number and call your dealer. Page 19
Uneven or inconsistent side glueLow glue level, low air pressure, or an unlevel nipper table.Keep glue about 3/4" below the top of the pot, make sure the compressor is at 90-110 psi, and level the nipper table. Page 15
Too little side glue on the non-operator sideSide glue wire is too far from the book.Loosen the side glue wire and move it closer to the rear side of the book. Page 11
Pages pull out easilyNotches too shallow or not enough glue on the spine.Raise the notching pins (no more than 1/16" into the pages), lower the metering roller, or adjust the Book Thickness Wheel. Keep the notching pins sharp. Page 12
Sheets fold over at the spineNipper adjustment knob set too tight.Open the nipper table further. Page 11

Frequently asked questions

How thick a book can the Sterling Digibinder Plus bind?

Up to 2 1/4" (55mm) thick (page 3).

What power does the Digibinder need?

220 volts, single phase, 15 amps. The tabletop version needs a table that supports 330 lbs (150 kg) (page 3, page 7).

What glue temperature should I use?

160°C is recommended. Warm-up takes up to 45 minutes, and the O button puts the machine in stand-by to keep glue from burning (page 8, page 14).

How do I make pads?

Flip the roughing motor toggle switch down, turn padding mode on with SET then X, and set Finish Time to 4 for pads (15 for perfect bound books) (page 8, page 12).

What weekly maintenance is required?

Check that the notching pins are sharp, bleed moisture from the compressor tank, check the compressor oil level and filter (page 14, page 15).