

Page 1 of 15

Text on page 2
Sterling Digipunch ®
Operator’s Training Manual
Issue 3 May 2016
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
1 | P age
Page 2 of 15

Text on page 3
Important Safety Notice! .................................................................................................................................. 3
Placing the Digipunch in the Proper Location ................................................................................................... 3
Preparing the Digipunch for Use ...................................................................................................................... 4
Turning on the Digipunch ................................................................................................................................. 4
Installing and Removing a Die .......................................................................................................................... 5
Disengaging a Punch Pin in a Die ...................................................................................................................... 5
Changing Format and Die type on Touch Screen .............................................................................................. 6
Custom Sizes ................................................................................................................................................. 6
Die Type ........................................................................................................................................................ 7
Loading Paper ................................................................................................................................................... 7
In-feed Table Up / Down Buttons ................................................................................................................. 7
Exit Table Up / Down Buttons: ..................................................................................................................... 7
Rear Cover Exit Guide ................................................................................................................................... 8
Paper Separator for Cover Material ................................................................................................................. 8
- Starting the Punching Process .......................................................................................................................... 8
Number of Sheets ......................................................................................................................................... 8
Speed Select & Setup Speed ......................................................................................................................... 9
- Waste Removal ................................................................................................................................................ 9
- Paper Jam ......................................................................................................................................................... 9
- Paper Parameters ........................................................................................................................................... 10
- Message Help Screens .................................................................................................................................... 11
- Die & Machine Maintenance .......................................................................................................................... 12
Die lubrication: ........................................................................................................................................... 12
Machine maintenance ................................................................................................................................ 12
- Troubleshooting ............................................................................................................................................. 13
- Machine Specifications ................................................................................................................................... 14
2 | P age
Page 3 of 15

Text on page 4
This manual contains very important safety information and must be read!
Digipunch Operators Training Manual
Issue 3 May 2016
The Digipunch will greatly increase productivity by removing the manual punching process by automation. An indepth look at the set up procedures is necessary to achieve maximum results follows.
The paper specifications for punching are between 12” un-punched x 14” punched side (maximum) down to 5- 1/2” x 5-1/2” (4-1/4” is also possible on the un-punched side using our small format option). It will also punch mixed stock including tabs and cover material. See paper specifications section for more information.
Tool Required: Two allen keys provided with machine.
- Important Safety Notice!
Make sure you read this section very carefully! Learn to recognize this Safety Alert Symbol. The Digipunch has been designed to provide a very high level of protection to an operator. Follow the guidelines below while installing, operating and maintaining your machine.
Always replace fuses or circuit breakers with the correct amperage and type.
If the machine cycles erratically, call dealer immediately for service.
Never bypass Safety devices.
Turn power switch off before performing maintenance.
- Placing the Digipunch in the Proper Location
Locate a clear work area 72” wide X 48” deep with a duplex outlet within 5 feet of the machine that provides a 125vac / 15-amp service (230vac / 16-amp European) which is protected by the customer’s circuit breaker box. The work area must be a solid and firm with a flat level surface.
3 | P age
Page 4 of 15

Text on page 5
- Preparing the Digipunch for Use
Some items may be packed inside waste drawer! Remove the machine from the crate by rolling it off the platform provided with the machine. Align one side of the platform on the pallet and the other end on the floor. Gently roll the machine off the pallet and onto the inclined platform until the machine is resting on the floor. The machine can be rolled into position resting on its wheels.
Remove the packing material located under the two upper feed belts located under the top clear cover.
Install the pile guides by inserting the black handle through the hole and into the nut located inside the channel. Do not over tighten! See figure 1.
Plug one end of power cord into machine socket located on the lower cabinet next to the main On / Off isolator switch. The other end can be plugged into a suitable wall outlet.
- Turning on the Digipunch
Turn the main power switch to the ”On” position. This switch is located on the lower left side of machine facing the operator’s display. The operator’s display will take about one minute to come up. You may hear and see the pile guides moving to the last saved position. This is normal and will not happen if a guard is open, die not installed or if the emergency switch is pressed down. See figure 2 & 3.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
4 | P age
Page 5 of 15

Text on page 6
Installing and Removing a Die
When the main screen comes up, you will see two menu choices. Enter the setup screen and press the "Die Removal" button. After a few seconds a message will appear "Die Is Ready for Removal". Open the rear cover and locate the die locking lever located on the machine frame closest to the operator. Pull the spring-loaded lever away from the die while pulling on the black die handle. Reinstall a different die into the opening lining up the die with the opening of the machine. Sometimes it may be necessary to raise or lower the upper channel of the die so it slides in to the movable holder. There are two notches cut into the die for odd or even hole patterns. Use the notch closest to the punch pins for an even amount of holes and the notch furthest away for an odd amount of holes. (If the holes are not centered within the sheet, please refer to the troubleshooting section of this manual). See figure 4, 5 & 6. Notches
- Disengaging a Punch Pin in a Die
It may be necessary to disengage two punch pins so the sheet edge, does not have a partial hole cut into each side. For 3-1, 2-1 and Comb dies, there are pin pulls located directly in front of the pin to be disengaged. These levers can be disengaged while the die is still in the machine. For all 4-1 pitch dies or any other die which does not have a pin pull, remove the 5 screws from the top plate of the die using a 1/8” allen wrench provided with the machine. Remove the appropriate punch pins and reassemble the die. It may be necessary to remove punch pins from a die which do have disengagement levers for non-standard size sheets. Follow the same procedure listed above. See figure 7 & 8.
5 | P age
Page 6 of 15

Text on page 7
7. Changing Format and Die type on Touch Screen
a. Format: There are several standard format sizes as well as one custom sizes to choose from located in the "Format Screen". The "Format Screen" button is located on the "Setup Screen". Locate the number next to the format you wish to punch. By pressing the black numbered box directly above the “Select Paper” a keypad will appear. Enter the number into the keypad and press enter key. If you enter a number outside of the range, the pop-up menu will remain until you escape or press a number in the correct range. Then press the “Set” button and the guides will automatically move to the correct position for the size chosen.
b. When choosing a standard size: (8-1/2" x 11" Landscape), means the guides will be set for punching on
the landscape side of the sheet (the long side). (8-1/2" x 11" Portrait) means the guides will be set for punching on the portrait side of the sheet (the short side). See figure 9 & 10.
- Custom Sizes: The custom size screen gives the operator the ability to choose any format from 12” x 14” down to 5-1/2” x 5-1/2” in small increments. There are 4 custom sizes which can be programmed as well as 4 custom metric sizes. You also have the ability to make small adjustments to standard sizes if the sheets are cut a fraction over or undersize.
To access this screen press the “Setup” button then “Format Change Screen” button. Then press “Custom Size” button and finally the “Next” button. Select the area just to the right of the custom size #9 thru #12 and press the number you need to change. A pop-up screen will appear to select a size. Select the size for the un-punched side as well as the punched side. Press the enter key after each selection. You do need to enter the decimal place when programming. If you enter a number outside of the range, the pop-up menu will remain until you escape or press a number in the correct range. Press the “Set” button when finished. Both rear and side guides will move to their new positions. See figure 11.
6 | P age
Page 7 of 15

Text on page 8
- Die Type: You can access these settings in the “Format Change”
screen. To change the die type selected in the touch screen, locate the number of the die next to the description. (For example, 4-1 round = #4). By pressing the black box directly above “Select Die” a keypad will appear. Enter the number into the keypad and press the enter key. If you enter a number outside of the range, the popup menu will remain until you escape or press a number in the correct range. Then press the “Set” button and the guides will automatically move to the correct position for the die type chosen. The Comb die is the only die with adjustable back stops. There are three positions which correspond to the three sizes preprogrammed into the die choices. Small, Medium & Large. See figure 12.
Always make sure you choose the correct format before loading paper!
Lower the in-feed table by pressing the "Load Paper" button located on the auto screen. Load the paper on the table between both lateral pile guides. Make sure the pile is all the way up against the front panel located under the paper separator. Loosen the rear pile guide assembly using the black handle. Move vertical pile guides up against the pile leaving about 1/16" between guides and pile. When punching tabs, loosen the two black round knobs and move each vertical pile guide to the outside edge of the pile next to the indent of the tab. If the paper pile contains heavy cover material it may be necessary to use the paper separator option. (See section 9 in this manual.) See figure 13.
- In-feed Table Up / Down Buttons: You can also move the In-feed up or down manually. These buttons are located in the “Setup Screen”. See figure 14.
- Exit Table Up / Down Buttons: You can also move the Exit Table up or down manually. These buttons are located in the “Setup Screen”. See figure 14.
7 | P age
Page 8 of 15

Text on page 9
c. Rear Cover Exit Guide: The exit guide will need to be removed for sheets longer than 9” or extended down for shorter sheets. This guide helps direct the paper into the exit table. See figure 15.
9. Paper Separator for Cover Material
When punching heavy cover material, you may notice covers that are marked or split because of the separating process or you may even have a paper jam associated with separating. When this happens, it will be necessary to engage the cover separator. Using a 5/32” allen key provided, loosen the adjustment setscrew located just under the paper separator and move it to the right to engage the cover separator mechanism. It is recommended that you return this feature to the left when not encountering problems with cover material. See figure 16.
- Starting the Punching Process
To start the punching process, go to the auto screen and press the "Start" button. The in-feed table will move up until the top of the paper pile is detected. The exit table will also move to its start position. Sometimes the pile may stop some distance from the separator, this is normal. The punch may cycle up to 15 times before taking the first lift of paper, only then will the punching process begin. To stop the punching process, press the "Punch / In-feed Stop" button. The paper in process will finish punching and unload automatically. Only use the "Emergency Stop" switch to stop the machine when an immediate stop is required. Paper joggers will normally reset after the emergency stop is released. If not, please reset joggers located in the "Format Change Screen". (If the machine stops cycling before the first lift of paper is punched, refer to the troubleshooting section of this manual). See figure 17.
- Number of Sheets: You can control the number of sheets to be punched for each lift from the “Auto” screen. By pressing the black numbered box directly below “Enter the Number of Sheets to Feed” a keypad will appear. Enter a number between 1-17 into the keypad and press enter. If you enter a number outside of the range, the pop-up menu will remain until you escape or press a number in the correct range. Normal punching is between 8 to 12 sheets. Lower numbers are used when punching only cover material or acetate. Higher numbers are for 3 hole punching and Velobind. (Because acetate is clear, the machine thinks there is no paper in the feed table and will shut down. Please refer to the troubleshooting section of this manual for correct settings).
8 | P age
Page 9 of 15

Text on page 10
- Speed Select & Setup Speed: Setup speed is used when encountering registration problems or paper jams. Go to the setup screen and press “Setup Speed On”. The machine will run at 75% of low speed. The speed select Button located on the “Auto Screen” will toggle between low running speed, (60 strokes per minute or high speed which is 72). You can stop the punching process by pressing “Setup Speed Off” button or turning the machine off from the auto screen. See figure 17.
- Sheet Counter or Paper amount: The sheet counter is located on the “Auto Screen” and provides an estimate of your production. If the job contains various thickness materials, as many do, it will not reflect the actual number of sheets but provides a means of measuring production throughout a given shift. You can also monitor how many inches of paper punched instead of sheets. This can be changed in the operator’s “Help Screen”. This number can be reset by pressing the black reset button located to the right of the number. See figure 17.
Unloading Paper: The exit table can be manually moved up or down using the two buttons located on the “Setup Screen”.
When the paper waste tray is full, a message will appear “Paper Waste Tray Full” letting the operator know it is time to empty the tray. To remove paper waste, locate the paper waste tray directly under the in-feed table. Pull the drawer all the way out to discard paper waste. Make sure the tray is pushed all the way in before starting the punching process! See figure 18.
There are two paper jam sensors which are located at the die station as well as the exit station.
Die Area: When a paper jam occurs inside the die area, the machine will stop and display the following message: “Paper Jam, Die Area”. Go to the setup screen and press the “Paper Jam Screen” button and then press the “Clear Jam” button. Wait for the punch die to reverse the pins out of the jammed paper. When the pins are clear of the paper the belts will automatically bring the paper out of the die for easy removal. Open the cover and remove the paper. (Sometimes the paper will show no signs of damage and can be placed in the exit tray as long as the holes were punched). Close the cover and wait for the machine to reset the paper joggers. Be careful not to bend the rear jogger brackets when removing paper! See figure 19.
9 | P age
Page 10 of 15

Text on page 11
Exit Area: If a jam occurs in the exit area, the machine will stop and display the following message: “Paper Jam, Exit Table). Please make sure you have the rear cover exit guide set correctly. See the loading paper section of this manual for setup procedure. After this jam is cleared, another message will be displayed that there is a jam in the die area. This is normal. You will need to remove the lift of paper in the die area before proceeding. See figure 20.
The following sizes can be punched on the Digipunch: 12” x 14” (14” is the punched side of the sheet) 5-1/2” x 5-1/2” (4-1/4 on the un-punched side is possible when using the small format option) Tabs ½” (Tabs must have a ¼” minimum indent to allow for stacking at the in-feed table) Covers 160lb Index max (Covers must be the same size of the body of the book) Acetate (Acetate should be punch separately. Set the number of sheets on “3”. You will also have to make a change in the maintenance screen, see troubleshooting)
When punching material with a curl, always place the open side of the curl down on the in-feed table. If there is toner buildup on the paper where one side of the pile is higher than the other, you will have to load smaller stacks. (If the machine stops cycling before the first lift of paper is punched, refer to the troubleshooting section of this manual). Always stack warm paper on a flat surface while cooling!
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 11 of 15

Text on page 12
- Message Help Screens
The below messages will be displayed in several screens alerting the operator of a certain condition. See figure 21.
“Machine Ready” “Please Wait” “Emergency Stop Push Button” “Die Not Locked in correct Position” “Top Cover Open” “Die Cover Open” “Die Not Installed Properly” “Paper Jam Die Area” “Paper Waste Tray Full” “Exit Table Full” “Paper Jam Exit Table “Press Help, Then Press Status”
(Machine is ready to punch paper) (Wait for joggers to move to their correct location) (Twist the red emergency stop knob to reset) (Check die locking lever is engaged properly into die notch) (Close the top cover) (Close the die cover) (Make sure die is in position) (Go to setup screen and press the “Paper Jam Screen” Button) (Empty paper waste tray) (Remove paper) (Clear jam, check to make sure exit guide are set properly) (Die may need to be lubricated or sharpened. Also, machine may need maintenance) (Main motor drive has faulted, try restarting machine)
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 12 of 15

Text on page 13
- Die & Machine Maintenance
Unplug the machine before going forward with maintenance!
The following items should be maintained every six months or when a message is displayed on the status screen “Call Dealer for Service”, “Lubricate Die” or “Sharpen Die” whichever comes first. Always clean the paper dust off of the items to be lubricated before proceeding.
a. Die lubrication: A message will appear after 100,000 sheets on a specific die to let you know it is time to maintain the die. Using lightweight machine oil, lubricate the die by running oil on the white felt strip located next to the row of punch pins. Press the clear message button located in the status screen to clear this message. (Dies may have to be lubricated more often depending on the material being punched).
b. Die sharpening: A message will appear after 5 million sheets on a specific die to let you know it is time to sharpen the die. Please call your dealer for more information on how to have your die sharpened. (Dies may have to be sharpened more often depending on material being punched)
c. Machine maintenance:
1. Lubricate the following items with white lithium grease or equivalent: Linear bearings, cams and cam followers.
2. Lubricate the following items with lightweight machine oil: All three lead screws for format change guides, pivot points and bronze bushings.
3. Open the electrical cabinet door and vacuum the paper dust in the electrical cabinet, the tops of the electrical components, and inside the machine.
4. Clean off the paper dust from all of the sensors and reflectors.
5. Make note of total cycle count located in maintenance screen. It is useful to know your service intervals. User; Password (call dealer for password)
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 13 of 15

Text on page 14
Problem Machine stops after 15 cycles without feeding paper. Feed table and exit table move down.
Cause
- Paper has toner buildup or curl which causes sensor to stop pile below the separator.
- Number of sheets selected is set low.
Paper skews when fed into belts.
1) Toner buildup causes uneven pile height which then drags on leaf spring brackets.
1) Wrong size selected.
2) Paper is smaller or larger than standard size selected.
The side joggers are away from edge of sheets or buckling the sheets.
The rear joggers are away from edge of sheets or buckling the sheets.
- Wrong size selected.
- Paper is smaller or larger than standard size selected.
The operator panel says “Machine Ready” but does not run when pressing start. (This can happen even though the display says everything is ok)
- Guard or cover switch may need adjustment.
- Die not pushed all the way into machine.
- Die interlock not engaged
Machine stops punching in the middle of a cycle. Display reads” Paper Jam Die Area”.
- Paper curled beyond specification.
- Too many sheets were fed into die.
- Jam actually caused in the exit area and then fell away from exit sensor.
- Die locking lever not adjusted properly.
Cover material is split or jams when being fed.
- Cover separator not engaged.
- Cover separator sticking.
Several sheets left behind on feed table. After punching, paper jams when exiting into exit tray.
1) Sheets being pushed under pile guide.
1) Adjustable cover guide in wrong position.
Paper interferes with side joggers when feeding.
- Lateral In-feed guides out of adjustment.
Solution
1) Go into maintenance screen and change the default 15 to a higher number IE. (25). Need password & username.
2) Increase the amount of sheets selected. (3-17)
1) Reduce the size of pile.
1) Check size chosen in setup screen.
2) Use custom size if sheet size is not standard.
1) Check size chosen in setup screen.
2) Use custom size if sheet size is not standard.
1) Make sure there is full travel with the guard & cover interlocks.
2) Check die installation.
3) Make sure the die locking lever is not sticking on side frame.
1) Let paper cool before running. Also stack your paper on a flat surface while cooling.
2) Punch fewer sheets. Can be an issue with the gripper.
3) If the paper falls slowly in exit area, this will cause the machine to stop with paper under the die jam sensor.
4) During punching, there is a lot of vibration which causes die locking lever to trip safety. Adjust switch.
1) Engage cover separator located on stainless steel caliper.
2) Make sure cover separator pivots up and down freely.
1) Make sure pile guides move freely up and down.
1) The adjustable paper guide should be set above edge of sheets so they fall freely onto pile.
1) Guides must be centered between side plates.
Page 14 of 15

Text on page 15
Holes not Centered in sheet.
- Die adjustment block not adjusted properly.
Rear jogger is behind the paper ½” or more.
1) Wrong size selected.
2) Rear jogger stays in clear jam position.
3) Die removal button pressed but die was not removed.
1) Loosen two allen screws on adjustment block. Move block until holes are centered.
1) Check size chosen on setup screen.
2) Go to clear jam screen and repeat clear jam. Open cover and then close to reset to chosen size.
3) Open any cover and close to reset jogger.
Electrical: 115 volt AC / 2 amp (230 volt AC / 1.5 amp) Uncrated Weight: 510 lbs. / 231Kg Floor Space: 47” x 30” x 48” / 119cm x 76cm x 122cm Crate size: 63” x 51” x 59” / 160cm x 130cm x 159cm Shipping Weight: 860 lbs. / 391Kg
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 15 of 15 ยท End of manual
Quick start
- Place the Digipunch in a clear 72" x 48" area within 5 feet of a 125vac / 15-amp outlet, remove packing from under the upper feed belts and install the pile guides.
- Turn on the main power switch on the lower left side and wait about one minute for the display.
- To change dies, press Die Removal on the Setup screen, open the rear cover, pull the locking lever and slide the die out. Use the die notch nearest the pins for an even number of holes, the far notch for odd.
- In the Format screen, enter the format number and die type number and press Set so the guides move into position.
- Press Load Paper, load the pile between the guides against the front panel, and bring the rear guides to about 1/16" from the pile.
- Enter the number of sheets per lift (1-17; 8-12 is normal) and press Start. Use Punch / In-feed Stop to finish and stop.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| "Paper Jam, Die Area" message | Paper jammed in the die station. | On the Setup screen press Paper Jam Screen, then Clear Jam. Wait for the pins to reverse and the belts to bring the paper out, then open the cover and remove it without bending the rear jogger brackets. Page 10 |
| "Paper Jam, Exit Table" message | Jam in the exit area, often from an incorrectly set rear cover exit guide. | Clear the jam, check the exit guide (remove it for sheets longer than 9", extend it for shorter sheets), then clear the lift remaining in the die area. Page 11 |
| Heavy covers marked, split or jamming during separation | Cover separator not engaged. | Loosen the setscrew under the paper separator with the 5/32" allen key and move it right to engage the cover separator. Return it left when not needed. Page 9 |
| Machine shuts down when punching acetate | Clear acetate is not detected as paper. | Punch acetate separately with sheets set to 3 and make the change in the maintenance screen. Page 11 |
| Holes not centered in the sheet | Die adjustment block not adjusted properly. | Loosen the two allen screws on the adjustment block and move it until the holes are centered. Page 15 |
| Rear jogger sits 1/2" or more behind the paper | Wrong size selected, jogger left in clear jam position, or Die Removal pressed without removing the die. | Check the selected size, repeat Clear Jam and open/close a cover to reset the jogger. Page 15 |
| "Press Help, Then Press Status" message | The die may need lubrication or sharpening, or the machine needs maintenance. | Check the status screen and lubricate or sharpen the die or service the machine as indicated. Page 12 |
Frequently asked questions
What paper sizes can the Digipunch punch?
From 12" x 14" (14" punched side) down to 5-1/2" x 5-1/2", or 4-1/4" on the un-punched side with the small format option. Covers up to 160 lb index and tabs with at least 1/4" indent are supported (page 11).
How fast does it punch?
Low speed is 60 strokes per minute and high speed is 72. Setup speed runs at 75% of low speed (page 10).
How often do the dies need lubrication and sharpening?
A message appears after 100,000 sheets to lubricate a die with lightweight machine oil on the felt strip, and after 5 million sheets to sharpen it (page 13).
What are the Digipunch's power and size specs?
115 volt AC / 2 amp (230 volt / 1.5 amp), 510 lbs uncrated, and a floor space of 47" x 30" x 48" (page 15).
How many sheets are punched per lift?
You can set 1-17 sheets; 8-12 is normal, fewer for covers or acetate and more for 3-hole and Velobind (page 9).
