

Page 1 of 11

Page 2 of 11

Text on page 3
Important Safety Notice! ....................................................................................................................................3
Placing the Looper in the Proper Location .........................................................................................................4
Preparing the Looper for Use .............................................................................................................................4
Turning on the Looper ........................................................................................................................................4
Installing the Side Tables and Waste Drawer .....................................................................................................5
Placing the Preloaded Wire-O on Strips into the Wire Holder ...........................................................................5
Adjusting the Wire-O Holder ..............................................................................................................................6
Wire-O Plate Strip Adjustment .......................................................................................................................6
Wire-O Gap Adjustment .................................................................................................................................6
Wire-O Holder Pusher Adjustment.................................................................................................................7
Wire-O Hanger Adjustment ............................................................................................................................7
Closing Bar Adjustment ......................................................................................................................................8
Closing Bar Height Adjustment .......................................................................................................................8
Closing Bar Skew Adjustment: ........................................................................................................................8
Book Placement Prior to Closing ....................................................................................................................8
Closing Bar Safety System ..............................................................................................................................9
- Troubleshooting .............................................................................................................................................. 10
Page 3 of 11

Text on page 4
This manual contains very important safety information and must be read!
Looper Operators Training Manual
Issue 1 October 2015
The Looper will greatly increase productivity by use of a Wire-O dispensing device which will automatically dispense a wire during the closing process. The wire is loaded into the machine preloaded on cardboard strips which holds around 20 pieces at a time. This reduces the handling, tangling as well as increasing productivity. It makes use of a sophisticated adjustable wire hanger which helps the operator during the insertion process. After the book is loaded onto the Wire-O, the operator removes the book from the wire holder and places it into the closing bar area. By pressing the foot pedal, the wire will be closed into the book as a new wire is released from the dispensing device. An in-depth look at set up procedures is necessary to achieve maximum results follows.
- Important Safety Notice!
Make sure you read this section very carefully! Learn to recognize this Safety Alert Symbol. The Looper has been designed to provide a very high level of protection to an operator. Follow the guidelines below while installing, operating and maintaining your machine.
Always replace fuses or circuit breakers with the correct amperage and type.
If the machine cycles erratically, call dealer immediately for service.
Never bypass Safety devices.
Turn power switch off before performing maintenance.
Page 4 of 11

Text on page 5
- Placing the Looper in the Proper Location
Locate a clear work area 37” wide x 31” deep with a duplex outlet within 5 feet of the machine that provides a 125vac / 15-amp service (230vac / 16-amp European) which is protected by the customer’s circuit breaker box. The work area must be a solid and firm with a flat level surface.
- Preparing the Looper for Use
Some items may be packed inside waste drawer! Remove the machine from the crate by lifting it off the platform with the handles located on each side of the machine. The machine weighs 154 pounds so two people are required.
If the optional stand has been purchased, then place the machine on the stand. If not, purchase a suitable table which can hold at least 200 pounds. Figure 1
Plug one end of power cord into the machine socket located on the lower right side next to the main On / Off switch. The other end can be plugged into a suitable wall outlet. Also plug in the foot pedal which is also located in the same location. Figure 2
- Turning on the Looper
Push the main power switch to the ”I” position which will turn on the machine and illuminate the switch. This switch is located on the lower right side when facing the front of the machine. The main fuse is also located within this switch housing. For some reason if the machine is plugged in and the switch does not illuminate when in the on position, this fuse should be checked.
Isolator Switch and Power Cord Location
Page 5 of 11

Text on page 6
Installing the Side Tables and Waste Drawer
Install both side tables by placing them on the handles located on each side of the machine. They are held in place under their own weight. The waste drawer is attached by two hangers located on the back of the machine. If the waste drawer adds too much depth to the machine then you can remove the drawer and move it closer to the wall. Either a bag or empty box placed on the floor will catch the waste. Figure 4
- Placing the Preloaded Wire-O on Strips into the Wire Holder
Note: You will need to move the blue wire holder up out of the way before setting up for a new size Wire-O. Pull both spring loaded handles out from both sides of machine and bring the blue wire holder all the way up away from the clear plastic guide. This needs to be all the way up to perform the next adjustment. Figure 5
Page 6 of 11

Text on page 7
7. Adjusting the Wire-O Holder
a. Wire-O Plate Strip Adjustment: Adjust the three plates so the slots of each plate line up with each cardboard strip. These plates are moved easily with your fingers. Make sure the strips are in the middle of each slot. Figure 6
Card board Strip Slot
- Wire-O Gap Adjustment: Pull both handles out away from machine and move the blue wire holder down until it just touches the loaded wire. Leave about 1/16” to 1/8” gap between the wire and blue guide. Figure 7
Page 7 of 11

Text on page 8
- Wire-O Holder Pusher Adjustment: The Wire-O pusher is used to push each individual wire from the machine and drop it onto the wire holder. The pusher can be turned off or on using the lever on the left side of the machine. If it is turned off, the machines closing bar will still function but not the dispenser. Loosen the locking knob on the left side of the machine and turn the knob on the right side of the machine so that the 0 mark is lined up with the wire size being used. Figure 8
- Wire-O Hanger Adjustment: There are two setting for the wire holder. You can move it laterally to the left or right for 3-1 or 2-1 sizes. It also is adjustable in and out to stabilize the wire as the book is being loaded. Figure 9
Page 8 of 11

Text on page 9
- Closing Bar Adjustment
The closing bar has several adjustments which need to be made to achieve a quality close. There is a height adjustment as well as a skew adjustment in case one side is closing more than the other side. There also is a built in safety system which will stop and reverse the motor if someone should have their hand or finger on top of the book.
- Closing Bar Height Adjustment: Turn the hand wheel until the indicator matches the correct wire size being closed. Figure 10
- Closing Bar Skew Adjustment: If the wire is closed more on one side compared to the other side, this can be adjusted by turning the knob located next to the hand wheel. You will first have to loosen both locking handles before the knob is moved. Figure 10
- Book Placement Prior to Closing: After the book is removed from the wire-o hanger and then placed into the closing mechanism. Make sure the book is all the way against the backstop before pressing the foot pedal. The book will move toward you as it closes which is normal. Figure 11
Page 9 of 11

Text on page 10
d. Closing Bar Safety System: There is a built in safety system located just under the closing bar which prevents the bar coming all the way down if the book is either too thick for the setting of the wire size or if some ones finger or hand was on top of the book. Figure 12 Do not operate this machine if the safety device is not working!
9. Wire-O Size Parameters
The following sizes can be closed on the Looper: 3-1 Wire-O sizes: 3-1 on cardboard strips are common from 3/16” to 9/16” 2-1 Wire-O sizes: 2-1 on cardboard strips are not common and will have to be specially ordered. The Wire-O dispenser can only hold up to 1” Wire-O. You can still close the 2-1 sizes by utilizing the wire hanger for easy loading. Closing Size: The closing bar height can be adjusted up to 1-1/2” Wire-O size. Book Size: Books up to 14” wide can be closed as well as dispensed.
Page 10 of 11

Text on page 11
Problem Machine does not turn on when main power switch is in its on position and not illuminated.
Cause
- Power cord not plugged in or power outlet not working.
- Blown Fuse.
Solution Make sure power cord is plugged into to the machine with voltage present at outlet. Replace fuse with correct voltage and type. Move blue wire holder away from wire. Move metal plates so card board strips line up with each slot.
The preloaded Wire-O does not fall down into holder. Wire-O strips do not line up with slots in metal plates.
1) Holder too tight against wire.
1) Plates not set in line with wire cardboard strips.
Wire-O doesn’t push out and fall into wire hanger.
1) Pusher not set correctly.
2) Pusher knob set to the off position.
1) Adjust Wire-O pusher knob so wire pushes and drops freely onto wire hanger.
2) Make sure pusher knob is set to the on position.
The Wire-O does not rest on wire hanger correctly.
1) Wire hanger is either too far in or not out enough.
2) Lateral adjustment not set correctly.
1) Move the wire hanger out enough to support the Wire-O but not too far so there is not enough room to load the thickness of the book.
2) Set the wire hanger to the correct position; 3-1 or 2-1.
Wire-O closes too tight or not tight enough.
1) Hand wheel setting is not set to the correct size.
1) This setting may have to be moved from the exact Wire-O size marks. The marks are for reference only.
Wire-O closes tighter on one end compared to opposite end.
1) Skew adjustment not set correctly.
1) Set Skew adjustment so both ends of Wire-O closes the same.
Closing bar stops halfway down or not in correct position.
1) Book too thick for Wire-O setting.
2) Safety guard is stuck in the up position.
1) Make sure the closing bar isn’t set too low for wire size being closed.
2) Turn off main power switch and check to make sure safety guard moves up and down freely.
Page 11 of 11 ยท End of manual
Quick start
- Set the Looper on its optional stand or a table that holds at least 200 lbs, within 5 feet of a 125vac / 15-amp outlet. It weighs 154 lbs, so use two people.
- Plug in the power cord and foot pedal on the lower right side, hang the side tables on the handles and attach the waste drawer to the rear hangers.
- Pull both spring-loaded handles and raise the blue wire holder, load the preloaded Wire-O strips, and line up the three plate slots with the cardboard strips.
- Lower the blue holder until it just touches the wire, leaving a 1/16" to 1/8" gap.
- Turn the pusher knob so the 0 mark matches the wire size, and set the wire hanger for 3-1 or 2-1 and in/out to support the wire.
- Turn the closing bar hand wheel to the wire size, place the loaded book fully against the backstop, and press the foot pedal to close.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not turn on and the power switch does not light | Power cord not plugged in, dead outlet, or blown fuse. | Check the cord and outlet voltage. Replace the fuse in the switch housing with the correct type. Page 11 |
| Preloaded Wire-O does not drop into the holder | Holder too tight against the wire, or plates not lined up with the cardboard strips. | Move the blue wire holder away from the wire and line up the metal plate slots with the strips. Page 11 |
| Wire-O does not push out onto the wire hanger | Pusher set incorrectly or switched off. | Adjust the pusher knob so the wire drops freely onto the hanger and make sure the pusher is on. Page 11 |
| Wire-O does not rest on the hanger correctly | Hanger too far in or out, or lateral setting wrong. | Move the hanger out just enough to support the wire and set it to the correct 3-1 or 2-1 position. Page 11 |
| Wire-O closes too tight or too loose | Hand wheel not set to the correct size. | Adjust the hand wheel; the size marks are for reference only. Page 11 |
| Wire-O closes tighter on one end | Skew adjustment set incorrectly. | Loosen both locking handles and turn the skew knob until both ends close the same. Page 11 |
| Closing bar stops halfway down | Book too thick for the wire setting, or the safety guard is stuck up. | Check the closing bar is not set too low for the wire size; turn off power and make sure the safety guard moves freely. Page 11 |
Frequently asked questions
What Wire-O sizes can the Looper close?
The closing bar adjusts up to 1-1/2" Wire-O. The dispenser holds up to 1" Wire-O; 3-1 strips are common from 3/16" to 9/16", while 2-1 strips must be specially ordered (page 10).
How wide a book can the Looper handle?
Books up to 14" wide can be closed and dispensed (page 10).
How much space and power does it need?
A clear area 37" wide x 31" deep, and a 125vac / 15-amp outlet (230vac / 16-amp in Europe) within 5 feet (page 5).
Can I close wire without using the dispenser?
Yes. Turn the pusher off with the lever on the left side; the closing bar still works but the dispenser does not (page 8).
What does the closing bar safety system do?
A sensor under the closing bar stops it from coming all the way down if the book is too thick for the setting or a hand or finger is on the book. Do not operate the machine if it is not working (page 10).
