

Page 1 of 49

Text on page 2
IDEAL 4815
IDEAL 4850
Page 2 of 49

Text on page 3
- Safety precautions •
IDEAL 4815 • IDEAL 4850
FIN
Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein. Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available. Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine, et attirons votre attention sur les consignes de sécurité. Les instructions d'utilisation et les consignes de sécurité doivent toujours être disponibles. Les instructions d'utilisation et les consi. Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en de veiligheids-voorschriften moeten altijd binnen handbereik zijn. Per favore legga questo manuale di istruzione prima di mettere in funzione il distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono essere sempre disponibili. Le recomendamos lea las instrucciones antes de poner en funcionamiento esta máquina y cumpla las normas de seguridad. Las instrucciones de servicio y seguridad deben estar siempre disponibles. Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig. Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen ! Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla. Lees gjennom denne bruksannvisningen før De tar i bruk maskinen Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen må alltid være tilgjengelig. Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być zawsze dostępne.
RUS Ïîæàëóéñòà, ïðî÷èòàéòå èíñòðóêöèþ ïî ýêñïëóàòàöèè ïåðåä óñòàíîâêîé
A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie. TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý her zaman kullanýma hazýr olmalýdýr. DK Før installation af maskinen bedes De venligst læse brugervejledningen og være opmærksom på sikkerhedsanvisningerne. Brugervejledningen skal altid være tilgængelig. CZ Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní upozornění. Návod k obsluze musí být vždy dostupný. P Por favor leiam o manual de instruções antes de colocar a máquina em operação e vejam as precauções de segurança. As instruções de operação deverão estar sempre disponíveis. GR ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ. ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ. SLO Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila preden zaženete naparavo. Navodila naj bodo vedno pri roki. SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na dostupnom mieste. EST Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige ohutusnõudeid. Kasutusjuhend peab alati käepärast olema. CHI
UAE
Page 3 of 49

Text on page 4
- Safety precautions •
D Keine Bedienung durch Kinder! GB Children must not operate the machine! F Pas d‘utilisation par un enfant! NL Geen bediening door kinderen! Non lasciare utilizzare il tagliacarte a bambini! E No dejar que la utilicen los niños! S Installera maskinen utom räckhåll för barn! FIN Asentakaa laite lasten ulottumattomiin ! N Installer maskinen utenfor rekkevidde for barn! PL Dzieciom nie wolno obsługiwać urządzenia ! RUS Íå äîïóñêàéòå äåòåé ê ïîëüçîâàíèþ àïïàðàòîì! H Gyerekek a gépet nem kezelhetik TR Makinayý Çocuklar Kullanmamalýdýr. DK Må kun betjenes af voksne CZ Stroj nesmí být obsluhován dětmi! P As crianças não devem trabalhar com a máquina! GR ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ. SLO Otroci ne smejo uporabljati naprave SK So strojom nesmú pracovat deti! EST Lapsed ei tohi masinat kasutada! CHI UAE
D Nicht unter das Messer fassen! GB Do not reach beneath the blade! F Ne pas passer les mains sous la lame! NL Niet met de handen onder het mes komen! Non toccare la lama nella parte inferiore! E ¡No tocar debajo de la cuchilla! S Sträck inte in handen under kniven! FIN Älä laita kättäsi terän alle ! N Plasser aldri hender ol. under kniven ! PL Nie wkładać rąk pod noże! RUS Èçáåãàéòå ïîïàäàíèÿ ðóê ïîä ëåçâèå! H Ne nyúljon a kés alá! TR Elinizi býçaðýn altýna sokmayýnýz! DK Stik ikke hænderne ind under knivbladet! CZ Nesahejte pod ostří nože! P Não tocar na parte inferior da faca! GR ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ! SLO Ne segajte z roko pod rezilo! SK Nevkladajte ruky pod nôž! EST Ärge pange kätt tera alla! CHI UAE
Page 4 of 49

Text on page 5
- Safety precautions •
IDEAL 4815 • IDEAL 4850
Messer nie lose liegen lassen! Messer nur mit Messerwechselvorrichtung oder im Messertransportkasten befördern! (siehe Seite 27 und 29). Warnung! Verletzungsgefahr! GB Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 27 and 29). Danger! Risk of injury! F Ne jamais laisser la lame sans protections ! Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf. page 27 et 29), ou transportée dans son étui en bois ! Danger! Risques de coupures ! NL Laat nooit de messen alleen achter. Transporteer de messen niet zonder de houten bescherming (zie pagina 27 en 29). Waarschuwing! Opgelet voor ongevallen! Non lasciare mai la lama incustodita. Non rimuovere o trasportare la lama senza protezione. (Vedi pagina 27 e 29). Attenzione! Rischio di infortunio! E ¡No quitar la cuchilla sin prestar atención. No desmontar no transportar la cuchilla sin protección! (vérase pág. 27 y 29) ¡Advertencia! ¡Peligro de hacerse daño! S Lämna aldrig maskinen obemannad. Ta inte ur eller transportera kniven utan skydd. (se sid 27 och 29). Skaderisk! FIN Käsittele terää aina varoen. Älä siirrä tai kuljeta terää ilman suojaa ! (katso sivu 27 ja 29 Loukkaantumisen vaara ! N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller transporter den uten beskyttelse (Se side 27 og 29) FARE ! Muligheter for skade ! PL Nigdy nie pozostawiać noży bez nadzoru. Nie wyciągać lub transportować noży bez osłon! (zobacz strona 27 i 29). Ryzyko skaleczenia sie! RUS Íå îñòàâëÿéòå îòêðûòîå ëåçâèå áåç ïðèñìîòðà! Íå
Soha ne hagyja a kést őrizetlenül! Ne vegye ki vagy ne szállítsa a kést védőtok nélkül! (Lásd 27. és 29. oldal) Veszély! Sérülésveszély! Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz! Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya taþýmayýnýz! (Sayfa 27 ve 29’e bakýnýz) Dikkat! Yaralanma riski!
Page 5 of 49

Text on page 6
- Safety precautions •
Knivbladet må aldrig efterlades uden opsyn. Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 27 og 29) FARE! Risiko for legemlig beskadigelse. CZ Nikdy nenechávejte nůž bez krytu. Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 27 a 29) Nebezpecí! Riskujete zranení P Deixar a faca sempre em local seguro! Não retirar ou transportar a faca sem protecção! (Ver pág. 27 e 29) Perigo! Risco de dano! GR ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ! ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 27 & 29) ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ ! SLO Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte rezilo brez zaščite. ( glej stran 27 in 29). Pozor! Nevarnost poškodbe. SK Nenechávajte nôž nechránený (nezabezpecený)! Nevyberajte alebo netransportujte nôž bez ochrany (vid s. 27 a 29 ! Riziko úrazu ! EST Ärge jätke lõiketera kunagi järelevalveta! Ärge pikendage ega teisaldage tera kaitseseadmeteta! (Vt lk 27 ja 29) Oht! Vigastuste oht! CHI
UAE
Page 6 of 49

Text on page 7
- Safety precautions •
IDEAL 4815 • IDEAL 4850
D GB F
Keine harten und splitternden Materialien schneiden! Do not cut hard materials or materials which may splinter! La coupe de matériaux trop durs ou risquant des projections est interdite ! NL Snij geen harde materialen of materiaal dat kan splinteren! Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi! E ¡No cortar materiales duros o materiales que puedan astillarse! S Förstör inte hârt material eller material som kan splittras! FIN Asentakaa laite lasten ulottumattomiin ! N Ikke kutt hardt metall eller materiale som kan splintre ! PL Nie ciąć twardych materiałów lub materiałów, które mogą ulec odpryśnięciu! RUS Äàííûé ðåçàê íå ïðåäíàçíà÷åí äëÿ ðåçêè òâåðäûõ
H TR DK
Ne vágjon kemény vagy olyan anyagot, amely repedhet! Sert veya parçalanabilecek malzemeleri kesmeyiniz! Der må ikke skæres i hårde materialer eller i materialer, der kan splintre! CZ Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré úlomky! P Não cortar materiais duros ou materiais que possam lascar! GR ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ! SLO Nikoli ne režite trdih materialov ali materialov, ki se lahko razcepijo. SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu vystrelovat ostré úlomky. EST Ärge lõigake kõvasid materjale ega materjale, mis võivad pilbasteks puruneda! CHI UAE
Page 7 of 49

Text on page 8
- Safety precautions •
The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation" only! Warning! Clips or similar damage the cutting blade.
Disconnect from the mains before starting any service work or before removing the panels!
Replacement of blade and cutting stick may be performed only when the main switch is switched off!
Page 8 of 49

Text on page 9
- Safety precautions •
IDEAL 4815 • IDEAL 4850
All components which could endanger the operator are covered by a guard!
Operating the machine without safety device is forbidden! (Front safety guard (A), rear screwed safety guard (B) and panel (C).
Page 9 of 49

Text on page 10
- Safety precautions •
The dangerous cutting movement is safeguarded by a movable guard (A) and a safety two-handed control system! (B)
Before working with the machine and after every blade replacement the automatic cut-off function of safety guard (A),(correct if distance between cover and table is < 20 mm) main switch (B) and control panel (C) must be checked.
Page 10 of 49

Text on page 11
- Safety precautions •
IDEAL 4815 • IDEAL 4850
Protect mains cable against heat, oil and sharp edges!
230V / 10A min 115V / 15A min
Connect the power cord to a single phase socket.
Ensure free access to mains!
Page 11 of 49

Text on page 12
- Safety precautions •
When not in use for a longer period switch off. (Main switch to "0").
Warning by IDEAL 4815 Danger! Blade must always be covered by the pressing bar.
OK
OK
Page 12 of 49

Text on page 13
IDEAL 4815 • IDEAL 4850
Remove the stand from the wooden pallet.
4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set (C).
Page 13 of 49

Text on page 14
Tools can be kept in the holder provided .
Cutting sticks (A) can be put in the tool holder
Page 14 of 49

Text on page 15
IDEAL 4815 • IDEAL 4850
Tighten the backgauge crank (A). Parts and tools are in the tool set (C).
Only IDEAL 4815 Attach the enclosed hand-wheel for clamping. Parts and tools are in the tool set (C).
Page 15 of 49

Text on page 16
Side tables (A), left and right are available as an option (Nr. 9000 528).
Plug into socket. The machine must be connected directly to the socket.
Page 16 of 49

Text on page 17
IDEAL 4815 • IDEAL 4850
It is forbidden to operate the machine if the operating and safety instructions have not been understood. Please check the safety devices are functioning and complete before use.
- All covers have to be mounted (A).
- The release for cutting is allowed only if the cover is closed and the two-hand safety device is operated at the same time (B)
- If the front cover closes by itself the gas spring (X) needs replacing.
We recommend you keep a record of your test results.
Page 17 of 49

Text on page 18
two-handed control system A - Safety Pre-clamping (only IDEAL 4850)
Overload switch
B - Blade
drive IDEAL 4815
Blade drive, clamp drive, IDEAL 4850
C - Display cutting size (cm or inch) D - Main switch handle for backgauge E - Crank setting
F - Key switch G - Paper clamp (only IDEAL 4815) H - Backgauge I - Side lay left and right J - Front safety guard K - Measuring unit (cm or inch) L - Display cutting size (cm or inch) M - Changeover (cm/inch)
Warning! Before cutting a measurement please check that the measurement scale (cm or inch) is adjusted correctly. See left picture.
Cutting activation Warning!
- Run backgauge to the front for turning the paper stack.
- Do not interrupt the upward movement of the blade by performing switching procedures.
- Close the front safety guard .
- Blade must always be at the top and be covered by the clamp. Do not touch the blade. (see safety information on page 32). Risk of injury!
Page 18 of 49

Text on page 19
IDEAL 4815 • IDEAL 4850
Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). Open the safety guard (C). The machine is now ready for use.
Page 19 of 49

Text on page 20
The measurement is set with the backgauge crank.(A) The symbol – rotary direction – moves to the right on the display (B) (see picture C). The rotary direction of the backgauge crank (A) is indicated on the right. Keep turning the backgauge crank to the right until a measurement appears (see picture E). The reference position is reached. The cutting size can now be set with the handle (A). If the backgauge is right at the front the symbol – rotary direction – will move to the left (see picture D). Turn the backgauge crank to the left until the rotary direction appears on the right in the display (see picture C). Afterwards turn the backgauge crank to the right until a measurements appears (see picture E). The reference position is reached. The cutting size can now be set with the handle (A). Proceed to position from the rear.
Measurement is shown on the display in inches or cm (B).
Information: When the machine is only switched off by the Key switch (main switch is still ON) it is not necessary to advance to the reference point.
Page 20 of 49

Text on page 21
IDEAL 4815 • IDEAL 4850
Cut according to markings Optical cutting line (A) that indicates the exact position of the cut. Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required).
- Adjust the backgauge with the crank handle to the back.
- Insert paper and move by means of the stacking angle to the backgauge and side lay on the left
- Turn the crank handle to the right until the marking on the paper to be cut is below the cutting line indicator.
Pull out the handle to avoid the measurement being wrongly adjusted.
Page 21 of 49

Text on page 22
Position the paper on the backgauge (A) and side lays left or right (B). To move paper stacks, please use the paper knock-up block (C) provided. (Run backgauge to the front for turning the paper stack).
Only 4815 Clamping is released by the hand-wheel. Before every cut lower the clamp by turning the hand-wheel to the right and tighten with a light twist.
IDEAL 4815
Press both actuators of the two-handed control system activation (A) simultaneously and them pressed until the paper is completely cut.
Page 22 of 49

Text on page 23
IDEAL 4815 • IDEAL 4850
IDEAL 4850
The clamp moves automatically when cutting is activated. The paper can also be pressed in advance. Clamping and cutting is activated by pressing actuators (A) on the front table.
IDEAL 4850
The actuator has 2 switching steps:
- pre-clamping
- automatic clamping and cutting
IDEAL 4850
Pre-clamping Press down both actuators to step 1
Clamp returns Press down completely one of the actuators
Cutting sequence with automatic clamping Press down both actuators to step 2
Page 23 of 49

Text on page 24
Close the safety guard.
Cutting activation: Press both buttons of the two-handed control system activation (A) simultaneously and them pressed until the paper is completely cut.
To interrupt or stop cutting: To interrupt or stop cutting, release both buttons (A) of the two-hand control.
Page 24 of 49

Text on page 25
- Blade and cutting stick replacement •
IDEAL 4815 • IDEAL 4850
If the cutting quality decreases:
- Check the cutting depth (see page 32).
- Check the cutting stick (see page 28).
- Replace or grind the blade (see page 24 - 32). The blade cannot be ground if the blade height is less than 83 mm/3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen.
Danger! Risk of injury! The blade is extremely sharp. Do not extract or transport the blade without protection. Changing the blade may only be performed by trained staff.
Page 25 of 49

Text on page 26
- Blade and cutting stick replacement •
Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set (A).
Close the safety guard (1.). Lower the blade by pressing both cutting actuators (2.). Keep one actuator pressed and turn off the main switch (3.).
Page 26 of 49

Text on page 27
- Blade and cutting stick replacement •
IDEAL 4815 • IDEAL 4850
The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B). Unscrew the blade screws (C) on the right hand side.
Remove the special wrench and turn on the main switch until the blade returns to the home position.
Warning by IDEAL 4815 Do not turn main switch to position "0" whilst blade is moving upwards! The clamp must always overlap the blade! Danger! Risk of injury!
Page 27 of 49

Text on page 28
- Blade and cutting stick replacement •
Position the main switch to "0" (1.) Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool (A) into place and fasten it to the blade (3.).
Remove 2 blade screws (1.). Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4).
Page 28 of 49

Text on page 29
- Blade and cutting stick replacement •
IDEAL 4815 • IDEAL 4850
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).
Replacing the cutting stick (not the blade).
- Turn the blade adjusting screw (A) to the left until it stops. (Otherwise the first cut will be too deep).
- Remove the cutting stick according to top picure.
- Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt. Danger! Risk of injury!
Cutting test after replacing the cutting stick (not the blade)
- Insert the paper and release the cut.
- If the last sheet of paper is not cut along the entire length turn the blade adjusting screw
- ¼ turn to the right.
- If the last sheet is still not completely cut repeat this process until the last sheet is cut along the entire length.
Page 29 of 49

Text on page 30
- Blade and cutting stick replacement •
Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A).
- Make sure there is a space ot 11 mm or 0.43 inches! (B).
- Blade must be covered! (C). Danger! Risk of injury!
11 mm 0.43 inch
Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).
Page 30 of 49

Text on page 31
- Blade and cutting stick replacement •
IDEAL 4815 • IDEAL 4850
Lightly tighten 2 of the 5 blade screws with washers (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws with washers (3.). Lightly screw in the right blade screw with the washer (A) when the blade is lowered.
Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position "I" (2.).
Page 31 of 49

Text on page 32
- Blade and cutting stick replacement •
Close the safety guard (1.) Lower the blade by pressing both cutting buttons (2.). Keep one button pressed and turn off the main switch (3.).
Open the safety guard (4.). With the special wrench (B) the 3 eccentrics should be screwed down (5.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).
Tighten the blade screws (A) on the right hand side. Turn main switch to position "I" (1.). Blade will return to upper position. Tighten the blade screws (2.) firmly.
Warning by IDEAL 4815 Do not turn main switch to position "0" whilst blade is moving upwards! The clamp must always overlap the blade! (see page 32). Danger! Risk of injury!
Page 32 of 49

Text on page 33
- Blade and cutting stick replacement •
IDEAL 4815 • IDEAL 4850
Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
Warning by IDEAL 4815 Danger! Blade must always be covered by the pressing bar (see picture below at the left).
OK
Clamping
Blade
OK
Page 33 of 49

Text on page 34
- Maintenance and cleaning •
Maintenance work may only be performed by trained staff.
Danger! Disconnect the mains before starting any service work or before removing the cover.
Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease). Grease the remaining parts twice a year (see picture). The main switch must be on "0" (B). Remove panel (C). Tools in tool set.
- Remove any paper.
- Grease the machine.
- Check the 4 joining bolts and 2 pushing bars for wear (D). If necessary inform your service personnel.
- Mount the machine.
= Greasing points on the machine.
Page 34 of 49

Text on page 35
- Maintenance and cleaning •
IDEAL 4815 • IDEAL 4850
Safety test The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.
Page 35 of 49

Text on page 36
- Possible malfuntions •
Machine does not function!
Is the machine plugged in?
Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Check the units fuse and the on-site circuit breaker! Release a cut see page 21 and 22.
Page 36 of 49

Text on page 37
- Possible malfuntions •
IDEAL 4815 • IDEAL 4850
Cut cannot be made.
- If cover is open: close it.
- If cover is closed: open and re-close it. (Security check).
Page 37 of 49

Text on page 38
- Possible malfuntions •
Machine turns off:
- Machine overloaded. Safety button (A) ejects. (Allow 1 minute cooling time and reset the safety button (A).
- Machine blocked.
- Blade is blunt. Eliminate the cause, and push the safety button (A).
Only IDEAL 4850
- Clamping drive blocked Safety button (B) ejects. Eliminate the cause, and push the safety button (B).
Safety button for:
A = Blade drive
B = Clamping drive
Page 38 of 49

Text on page 39
- Possible malfuntions •
IDEAL 4815 • IDEAL 4850
Does not cut through the last sheet:
- Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B) (see page 32).
Poor cutting quality or blade stays in the paper stack.
- Change the blade (C) (see pages 24 - 32.
Page 39 of 49

Text on page 40
- Possible malfuntions •
Motor runs but blade does not move downwards.
- Security brake has been activated! Inform the Service Team!
- www.ideal.de "Service" service@krug-priester.com
Display illumination off
- Machine is plugged in? (A)
- Main switch on position "I"? (B)
- Push in the safety button! (C)
- Check the units fuse and the on-site circuit breaker!
Page 40 of 49

Text on page 41
- Possible malfuntions •
IDEAL 4815 • IDEAL 4850
None of the above mentioned methods helped to solve the problem: Contact Service Team under
- www.ideal.de "Service" service@krug-priester.com
Page 41 of 49

Text on page 42
Recommended accessories:
Blade
- Nr. 9000 021
Cutting stick (6 pieces)
- Nr. 9000 022
Blade changing tool 1
- Nr. 9000 518
Paper knock-up block 1
- Nr. 9000 521
Side tables left and right
- Nr. 9000 528
Page 42 of 49

Text on page 43
- Technical data •
IDEAL 4815 • IDEAL 4850
Technical data:
- Power supply: 230V/50Hz/1~,120V/60Hz/1~
- Cutting height: 80 mm
- Sound level EN 13023: < 70 dB (A)
- Leakage current < 3,5mA
- Power cord gauge min. 1,5mm 2 (230V).
- Power cord gauge AWG 14 (15A) (120V) (IDEAL 4815)
- Power cord gauge AWG 12 (20A) (120V) (IDEAL 4850)
The exact technical specifications can be found on the technical specifications sticker (A) on the machine. A wiring diagram is found in the electrical switch box. To claim under guarantee, the machine must still carry its original identification label.
IDEAL 4815
IDEAL 4850
Cuttinglength mm
Tabledepth mm
Minimum space requirement (BXTXH) mm
Weight kg
- with side tables: 1365 mm
- * with side tables: IDEAL 4815 / 221 kg
- ** with side tables:IDEAL 4850 / 234 kg
Page 43 of 49

Text on page 44
- Technical data •
This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and 2004/108/EG.
Sound level information: The sound level is < 70 db (A) as defined by EN 13023.
Subject to alteration without notice.
Page 44 of 49

Text on page 45
- Technical data •
IDEAL 4815 • IDEAL 4850
Krug + Priester has a certified quality management system according to DIN EN ISO 9001:2008 and a certified environmental management system according to DIN ISO 14001:2009.
Page 45 of 49

Text on page 46
D GB F
EG-KONFORMITÄTSERKLÄRUNG
EC-declaration of conformity Déclaration de conformité CE
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
GS- IDENT. Nr. 11481001 11485001
UL- IDENT. Nr. 10481001 10485001
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
2006/42/EG: Maschinenrichtline, EC Machinery directive, EC Directives machines. 2004/108/EG: EMV Richtline, EMV Electromagnetic compatibility directive, EMV directives compatibilité électromagnétique 2011/65/EU RoHS Richtlinie, RoHS directive, RoHS directives.
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3; EN ISO 12100; EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1
29.12.2009 Datum
Bevollmächtigter für technische Dokumentation Authorized representative for technical documentation Représentant autorisé pour la documentation technique
Krug & Priester GmbH u. Co KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany)
Page 46 of 49

Page 47 of 49

Page 48 of 49

Text on page 49
IDEAL • Made in Germany
- Document Shredders •
- Trimmers and Guillotines •
Page 49 of 49 Β· End of manual
Quick start
- Set up: remove the stand from the wooden pallet. Four strong people are needed to lift the machine onto the stand. Secure it with the 4 screws, put the shelf on the stand, and tighten the backgauge crank.
- Connect power: plug the power cord directly into a single phase socket (230V / 10A min or 115V / 15A min) and keep free access to the mains.
- Check safety devices: before use, make sure all covers are mounted and check that the safety guard, main switch and control panel cut-off functions work.
- Start the machine: set the main switch to "I", insert the control key and turn it to the right, then open the safety guard.
- Find the reference position: turn the backgauge crank to the right until a measurement appears on the display. Check that the display is set to the correct scale (cm or inch).
- Position the paper: set the cutting size with the crank, then place the paper against the backgauge and the left or right side lay. Use the paper knock-up block to move stacks.
- Cut: close the safety guard, then press both buttons of the two-handed control at the same time and keep them pressed until the paper is completely cut. The clamp moves automatically.
- Shut down: when the machine will not be used for a longer period, set the main switch to "0".
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not function | Not plugged in, main switch off, control system not activated, or a fuse or breaker has tripped | Check the plug, set the main switch to "I", turn the control key to the right, and check the unit fuse and the on-site circuit breaker. Page 36 |
| A cut cannot be made | The front cover is open, or the cover security check has not reset | If the cover is open, close it. If it is closed, open and re-close it. Page 37 |
| Machine turns off and safety button A pops out | Machine overloaded, blocked, or the blade is blunt | Allow 1 minute cooling time, eliminate the cause, and push safety button A back in. Page 38 |
| Safety button B pops out | Clamping drive blocked | Eliminate the cause and push safety button B back in. Page 38 |
| The last sheet is not cut through | Worn cutting stick or blade depth set too high | Turn or turn around the cutting stick, then turn the blade depth adjustment knob ΒΌ turn to the right at a time until the last sheet is cut along the entire length. Page 39 |
| Poor cutting quality, or the blade stays in the paper stack | Blade is blunt | Change the blade. A blade with a height under 83 mm/3.29 inches cannot be ground and must be replaced. Page 39 |
| Motor runs but the blade does not move down | The security brake has been activated | Inform the service team. Page 40 |
| Front cover closes by itself | Worn gas spring | Have the gas spring replaced. Page 17 |
Frequently asked questions
How high a stack can the 4850 cut?
The cutting height is 80 mm. See page 43.
Does the 4850 clamp the paper automatically?
Yes. The clamp moves automatically when cutting starts. The actuators have 2 steps: press both to step 1 to pre-clamp, and both to step 2 for automatic clamping and cutting. See page 23.
Can I cut to printed marks?
Yes. An optical cutting line shows the exact position of the cut, and the blade cuts on its front edge. Turn the crank until the mark on the paper is below the line. Use it only when an exact cut is not required. See page 21.
How often can the cutting stick be used?
Each cutting stick can be used eight times by turning it. Replacement cutting sticks come 6 pieces per pack (Nr. 9000 022). See page 29, page 42.
