

Page 1 of 53

Text on page 2
IDEAL 4860
IDEAL 5260 IDEAL 6660
Page 2 of 53

Text on page 3
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
DE Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitung und beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeit verfügbar sein. EN Please read these operating instructions before putting the machine into operation and observe the safety precautions. The operating instructions must always be available. FR Nous vous prions de lire attentivement le mode d’emploi avant d’utiliser la machine, et attirons votre attention sur les consignes de sécurité. Les instructions d‘utilisation et les consignes de sécurité doivent toujours être disponibles. Les instructions d‘utilisation et les consi. NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzing goed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing en de veiligheids-voorschriften moeten altijd binnen handbereik zijn. IT Per favore legga questo manuale di istruzione prima di mettere in funzione il distruggidocumenti e osservi le regole di sicurezza. Le istruzioni d’uso devono essere sempre disponibili. ES Le recomendamos lea las instrucciones antes de poner en funcionamiento esta máquina y cumpla las normas de seguridad. Las instrucciones de servicio y seguridad deben estar siempre disponibles. SV Läs igenom denna bruksanvisning innan ni startar maskinen. Var noga med säkerhetsföreskrifterna. Instruktionsmanualen måste alltid finnas tillgänglig. FI Lue nämä käyttö-ohjeet läpi ennenkuin käynnistät laitteen ! Noudata turvaohjeita. Käyttöohjeiden on oltava aina saatavilla. NO Lees gjennom denne bruksannvisningen før De tar i bruk maskinen Vær oppmerksom på sikkerhetsforskriftene. Opperatørmanualen må alltid være tilgjengelig. PL Proszę uważnie przeczytać instrukcję obsługi przed uruchomieniem urządzenia i stosować się do przepisów bezpieczeństwa. Instrukcje obsługi muszą być zawsze dostępne. RU Пожалуйста, прочитайте инструкцию по эксплуатации перед установкой
HU A gép üzembe helyezése elott figyelmesen olvassa el a kezelési utasítást és tartsa be a biztonsági eloírásokat.Kezelési utasításnak mindig elérhetonek kell lennie. TR Lütfen makineyi çalýþtýrmadan önce bu kullanma talimatlarýný dikkatli bir þekilde okuyunuz ve belirtilen güvenlik önlemlerine uyunuz. Kullanma Talimatlarý her zaman kullanýma hazýr olmalýdýr. DA Før installation af maskinen bedes De venligst læse brugervejledningen og være opmærksom på sikkerhedsanvisningerne. Brugervejledningen skal altid være tilgængelig. CS Prosím přečtěte si instrukce k obsluze a dodržujte bezpečnostní upozornění. Návod k obsluze musí být vždy dostupný. PT Por favor leiam o manual de instruções antes de colocar a máquina em operação e vejam as precauções de segurança. As instruções de operação deverão estar sempre disponíveis. EL ÐÁÑÁÊÁËÙ ÄÉÁÂÁÓÔÅ ÔÉÓ ÏÄÇÃÉÅÓ ×ÑÇÓÅÙÓ ÊÁÉ ÔÉÓ ÐÑÏÖÕËÁÎÅÉÓ ÁÓÖÁËÅÉÁÓ ÐÑÉÍ ÂÁËÅÔÅ ÔÏ ÌÇ×ÁÍÇÌÁ ÓÅ ËÅÉÔÏÕÑÃÉÁ. ÏÉ ÏÄÇÃÉÅÓ ×ÑÇÓÇÓ ÐÑÅÐÅÉ ÍÁ ÅÉÍÁÉ ÐÁÍÔÁ ÄÉÁÈÅÓÉÌÅÓ. SL Prosimo preberite navodila za uporabo ter upoštevajte varnostna opozorila preden zaženete naparavo. Navodila naj bodo vedno pri roki. SK Starostlivo si preštudujte tento návod na obsluhu pred uvedením stroja do prevádzky a najmä bezpecnostné predpisy. Držte tento návod na obsluhu na dostupnom mieste. ET Palun lugege enne masina käivitamist käesolevat kasutusjuhendit ning järgige ohutusnõudeid. Kasutusjuhend peab alati käepärast olema. ZH
Page 3 of 53

Text on page 4
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
DE In der Nähe der Schneidemaschine keine Spraydosen mit entzündbaren Stoffen benutzen! EN Do not use any spray cans with flammable content near to the cutting machine! FR Ne pas utiliser d’aérosols de substances inflammables à proximité du massicot ! NL Gebruik in de buurt van de snijmachine geen spuitbussen met ontvlambare stoffen! IT Non utilizzare bombolette spray in prossimità del tagliacarte! ES ¡No utilizar aerosoles con sustancias inflamables cerca de la guillotinas! SV Använd inga sprayburkar med brandfarliga ämnen i närheten av skärmaskiner! FI Paperileikkurit lähellä ei saa käyttää syttyviä aineita sisältäviä suihkepulloja! NO Ikke bruk noen spraybokser med antennelige stoffer i nærheten av skjæremaskiner! PL W pobliżu niszczarki do gilotyne nie używać aerozoli zawierających palne substancje! RU Не пользоваться вблизи режущих машин аэрозольными
HU Az szeletelők közelében nem szabad gyúlékony anyagokat tartakmazó spray dobozokat használni! TR Giyotinler yakınlarında yanıcı madde içeren sprey kutuları kullanmayınız! DA Nær skæremaskine eller aerosol brug med brandfarlige stoffer! CS V blízkosti stohový řezací stroje nepoužívejte spreje s hořlavými látkami! PT Não usar latas de aerossóis com substâncias inflamáveis na proximidade do cisalhas e guilhotinas! EL Κοντά στον φέτες δεν επιτρέπεται να υπάρχουν δοχεία σπρέι με εύφλεκτες ουσίες! SL V bližini giljotine ne uporabljatirazpršilnih sprejev z vnetljivimi snovmi! SK V blízkosti rezačka papiera nepoužívajte spreje s horľavými látkami! ET Mitte kasutada giljotiinid lähedal süttivaid aineid sisaldavaid aerosoole! ZH 不得在切片機附近使用装有易燃物质的喷雾罐! AR ! يتعين عدم استخدام الرذاذ مع المواد القابلة للاشتعال بالقرب من تقطيع
Page 4 of 53

Text on page 5
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
DE Keine entzündbaren Reinigungsmittel verwenden. EN Do not use any flammable cleaning agents. FR Ne pas utiliser de détergents inflammables. NL Gebruik geen ontvlambare reinigingsmiddelen. IT Non utilizzare detergenti infiammabili. ES No utilizar productos limpiadores inflamables. SV Använd inga brandfarliga rengöringmedel. FI Älä käytä syttyviä puhdistusaineita. NO Ikke bruk noen antennelige rengjøringsmidler. PL Nie stosować palnych środków czyszczących. RU Не использовать воспламеняющиеся средства для
HU Ne használjon gyúlékony tisztítószereket. TR Yanıcı temizlik maddeleri kullanmayınız. DA Brug ikke brændbare rengøringsmidler. CS Nepoužívejte hořlavé čisticí prostředky. PT Não utilizar produtos de limpeza inflamáveis. EL Μη χρησιμοποιείτε εύφλεκτα καθαριστικά μέσα. SL Ne uporabljati vnetljivih čistilnih sredstev. SK Nepoužívajte horľavé čistiace prostriedky. ET Mitte kasutada süttivaid puhastusvahendeid. ZH 请勿使用易燃清洁剂。 AR ينبغي عدم استعمال مواد التنظيف القابلة للاشتعال.
Page 5 of 53

Text on page 6
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
DE Keine Bedienung durch Kinder! EN Children must not operate the machine! FR Pas d‘utilisation par un enfant! NL Geen bediening door kinderen! IT Non lasciare utilizzare il tagliacarte a bambini! ES No dejar que la utilicen los niños! SV Installera maskinen utom räckhåll för barn! FI Asentakaa laite lasten ulottumattomiin ! NO Installer maskinen utenfor rekkevidde for barn! PL Dzieciom nie wolno obsługiwać urządzenia ! RU Не допускайте детей к пользованию аппаратом! HU Gyerekek a gépet nem kezelhetik TR Makinayý Çocuklar Kullanmamalýdýr. DA Må kun betjenes af voksne CS Stroj nesmí být obsluhován dětmi! PT As crianças não devem trabalhar com a máquina! EL ÁÐÁÃÏÑÅÕÅÔÁÉ Ç ×ÑÇÓÇ ÁÐÏ ÐÁÉÄÉÁ. SL Otroci ne smejo uporabljati naprave SK So strojom nesmú pracovat deti! ET Lapsed ei tohi masinat kasutada! ZH AR
DE Nicht unter das Messer fassen! EN Do not reach beneath the blade! FR Ne pas passer les mains sous la lame! NL Niet met de handen onder het mes komen! IT Non toccare la lama nella parte inferiore! ES ¡No tocar debajo de la cuchilla! SV Sträck inte in handen under kniven! FI Älä laita kättäsi terän alle ! NO Plasser aldri hender ol. under kniven ! PL Nie wkładać rąk pod noże! RU Избегайте попадания рук под лезвие! HU Ne nyúljon a kés alá! TR Elinizi býçaðýn altýna sokmayýnýz! DA Stik ikke hænderne ind under knivbladet! CS Nesahejte pod ostří nože! PT Não tocar na parte inferior da faca! EL ÌÇÍ ÁÃÃÉÆÅÔÅ ÔÏ ÊÁÔÙ ÌÅÑÏÓ ÔÇÓ ËÅÐÉÄÁÓ! SL Ne segajte z roko pod rezilo! SK Nevkladajte ruky pod nôž! ET Ärge pange kätt tera alla! ZH AR
Page 6 of 53

Text on page 7
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
DE Messer nie lose liegen lassen! Messer nur mit Messerwechselvorrichtung oder im Messertransportkasten befördern! (siehe Seite 33 und 35). Warnung! Verletzungsgefahr! EN Never leave the blade unattended! Do not extract or transport the blade without protection! (See page 33 and 35). Danger! Risk of injury! FR Ne jamais laisser la lame sans protections ! Elle ne doit être démontée qu’à l’ aide du dispositif de changement de lame (cf. page 33 et 35, ou transportée dans son étui en bois ! Danger! Risques de coupures ! NL Laat nooit de messen alleen achter. Transporteer de messen niet zonder de houten bescherming (zie pagina 33 en 35). Waarschuwing! Opgelet voor ongevallen! IT Non lasciare mai la lama incustodita. Non rimuovere o trasportare la lama senza protezione. (Vedi pagina 33 e 35). Attenzione! Rischio di infortunio! ES ¡No quitar la cuchilla sin prestar atención. No desmontar no transportar la cuchilla sin protección! (vérase pág. 33 y 35) ¡Advertencia! ¡Peligro de hacerse daño! SV Lämna aldrig maskinen obemannad. Ta inte ur eller transportera kniven utan skydd. (se sid 33 och 35). Skaderisk! FI Käsittele terää aina varoen. Älä siirrä tai kuljeta terää ilman suojaa ! (katso sivu 33 ja 35) Loukkaantumisen vaara ! NO La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller transporter den uten beskyttelse (Se side 33 og 35) FARE ! Muligheter for skade ! PL Nidy nie pozostawiać noży bez nadzoru! Nie wyciągać lub transportować noży bez osłon! (zobacz strona 33 i 35). Ryzyko skaleczenia się! RU Не оставляйте открытое лезвие без присмотра! Не
HU Soha ne hagyja a kést őrizetlenül! Ne vegye ki vagy ne szállítsa a kést védőtok nélkül! (Lásd 33. és 35. oldal) Veszély! Sérülésveszély! TR Býçaðý hiçbir zaman gözetimsiz býrakmayýnýz! Býçaðý muhafazasýz olarak yerinden çýkartmayýnýz veya taþýmayýnýz! (Sayfa 33 ve 35 bakýnýz) Dikkat! Yaralanma riski!
Page 7 of 53

Text on page 8
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
DA Knivbladet må aldrig efterlades uden opsyn. Forsøg ikke at afmontere eller transportere knivbladet uden beskyttelse! (Se side 33 og 35) FARE! Risiko for legemlig beskadigelse. CS Nikdy nenechávejte nůž bez krytu. Nikdy nevyjímejte nebo neprepravujte nuz bez ochranného krytu (viz. strany 33 a 35) Nebezpecí! Riskujete zranení PT Deixar a faca sempre em local seguro! Não retirar ou transportar a faca sem protecção! (Ver pág. 33 e 35) Perigo! Risco de dano! EL ÌÇÍ ÁÖÇÍÅÔÅ ÔÇÍ ËÅÐÉÄÁ ÁÍÅÐÉÔÇÑÇÔÇ! ÌÇÍ ÁËËÁÆÅÔÅ ¹ ÌÅÔÁÖÅÑÅÔÅ ÔÇÍ ËÅÐÉÄÁ ×ÙÑÉÓ ÐÑÏÖÕËÁÎÇ (Äåßôå ó÷åôéêÜ óôéò óåëßäåò 33 & 35) ÐÑÏÓÏ×Ç ! ÊÉÍÄÕÍÏÓ ÔÑÁÕÌÁÔÉÓÌÏÕ ! SL Nikoli ne puščajte rezila nazaščitenega. Nikoli ne prenašajte rezilo brez zaščite. (glej stran 33 in 35). Pozor! Nevarnost poškodbe. SK Nenechávajte nôž nechránený (nezabezpecený)! Nevyberajte alebo netransportujte nôž bez ochrany (vid s. 33 a 35) ! Riziko úrazu ! ET Ärge jätke lõiketera kunagi järelevalveta! Ärge pikendage ega teisaldage tera kaitseseadmeteta! (Vt lk 33 ja 35) Oht! Vigastuste oht! ZH
Page 8 of 53

Text on page 9
- Sicherheitshinweise • Safety precautions •
- Consignes de sécurité • Veiligheidsvoorschriften •
- Misure di Sicurezza • Normas de Seguridad •
- Säkerhetsföreskrifter • Turvallisuusohjeita • Sikkerhetsforskriftene •
- Środki bezpieczeństwa • Ìåðû ïðåäîñòîðîæíîñòè •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
DE Keine harten und splitternden Materialien schneiden! EN Do not cut hard materials or materials which may splinter! FR La coupe de matériaux trop durs ou risquant des projections est interdite ! NL Snij geen harde materialen of materiaal dat kan splinteren! IT Utilizzare il tagliacarte esclusivamente per il taglio di risme di carta o materiali analoghi! ES ¡No cortar materiales duros o materiales que puedan astillarse! SV Förstör inte hârt material eller material som kan splittras! FI Asentakaa laite lasten ulottumattomiin ! NO Ikke kutt hardt metall eller materiale som kan splintre ! PL Nie ciąć twardych materiałów lub materiałów, które mogą ulec odpryśnięciu! RU Данный резак не предназначен для резки твердых
HU Ne vágjon kemény vagy olyan anyagot, amely repedhet! TR Sert veya parçalanabilecek malzemeleri kesmeyiniz! DA Der må ikke skæres i hårde materialer eller i materialer, der kan splintre! CS Neřežte tvrdý materiál, při kterém mohou ustřelovat ostré úlomky! PT Não cortar materiais duros ou materiais que possam lascar! EL ÌÇÍ ÊÏÂÅÔÅ ÓÊËÇÑÁ ÕËÉÊÁ ¹ ÕËÉÊÁ ÐÏÕ ÈÑÕÌÌÁÔÉÆÏÍÔÁÉ! SL Nikoli ne režite trdih materialov ali materialov, ki se lahko razcepijo. SK Nerežte tvrdé materiály, alebo materiály, z ktorých môžu vystrelovat ostré úlomky. ET Ärge lõigake kõvasid materjale ega materjale, mis võivad pilbasteks puruneda! ZH AR
Page 9 of 53

Text on page 10
- Safety precautions •
The machine is designed for cutting stacks of paper to a specified size. This machine is constructed for "one-man operation" only! Warning! Clips or similar damage the cutting blade.
Disconnect from the mains before starting any service work or before removing the panels!
Replacement of blade and cutting stick may be performed only when the main switch is switched off!
Page 10 of 53

Text on page 11
- Safety precautions •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
All components which could endanger the operator are covered by a guard!
Operating the machine without safety device is forbidden! (Rear screwed safety guard (A) and panel (B)).
Page 11 of 53

Text on page 12
- Safety precautions •
The cutting action, which is dangerous to the operator,is
- protected by a two-handed control system (A)
- and safety beam guard (B).
Protect mains cable against heat, oil and sharp edges!
Page 12 of 53

Text on page 13
- Safety precautions •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
230V / 10A min 115V / 15A min
Connect the power cord to a single phase socket.
Ensure free access to mains!
When not in use for a longer period switch off. (Main switch to "0").
Page 13 of 53

Text on page 14
- Safety precautions •
Danger! Blade must always be covered by the pressing bar.
OK
OK
Page 14 of 53

Text on page 15
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Remove the stand from the wooden pallet.
4 strong people are required to lift the machine from the pallet and place it on the stand. Secure with 4 screws (A). Put the shelf (B) on the stand. (Parts and tools are in the tool set) (C).
Page 15 of 53

Text on page 16
Tools can be kept in the holder provided.
Cutting sticks (A) can be put in the tool holder.
Page 16 of 53

Text on page 17
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Side tables (A), left and right are available as an option (No. 9000 528).
Plug into socket. The machine must be connected directly to the socket.
Page 17 of 53

Text on page 18
The machine may only be operated, if the operating instructions and the safety instructions have been understood. Before each use, check the safety equipment for completeness and functionality.
- All covers have to be mounted (A).
- Safety beam guard must be mounted (B).
- The release for cutting is allowed only if the two-hand safety device is operated at the same time (C)
- Safety light beam: If the test rod (E, tool kit) is held into the protective field (D), an activated work cycle must be stopped immediately.
We recommend you keep a record of your test results.
STOP
Page 18 of 53

Text on page 19
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Position the main switch to "I" (A). Insert the key for the control system and move it to the right (B). The machine is now ready for use.
Press START (C). Machine will automatically go to the start position.
Bright LEDs illuminate the working area (D). The LED button (E) has 4 switching steps brightness 3 Press 1 x brightness 2 Press 2 x brightness 1 Press 3 x OFF Press 4 x
The light can also be switched off by pressing symbol a few and keeping pressed the seconds.
The measurement is set either with the handwheel (A) or by programming (B) the cutting measurements. Measurement is shown on the display in inches or cm (B).
Page 19 of 53

Text on page 20
Optical cutting line (A) that indicates the exact position of the cut. Blade cuts on the front edge (B) of the light beam. (Only use when no exact cut is required).
Position the paper on the backgauge (A) and side lays left or right (B). To move paper stacks, please use the paper knock-up block (C) provided. (Run backgauge to the front for turning the paper stack).
Page 20 of 53

Text on page 21
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
The clamp moves automatically when cutting is activated.
The paper can also be pressed in advance. Clamping and cutting is activated by the actuators (A) on the front table.
The actuator has 2 switching steps:
- pre-clamping
- automatic clamping and cutting
= Pre-clamping
= Clamp returns
Press down both actuators to step 1
Press down completely one of the actuators
= Cutting sequence with automatic clamping
Press down both actuators to step 2
Page 21 of 53

Text on page 22
Cutting activation: Press both actuators of the two-handed control system (A) simultaneously and keep pressed until the paper is completely cut.
To interrupt or stop cutting: To interrupt or stop cutting, release both actuators (A) of the two-handed control.
Page 22 of 53

Text on page 23
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
A - Safety two-handed control system
B - Overload switch
(blade drive/clamp drive/ backgauge drive)
C - Backgauge control D - Main switch E - Hand-wheel for backgauge setting F - Key switch G - Backgauge H - Side lay left and right
Start machine
- Main switch to position "I", insert the key for the control panel and turn to the right. Start screen appears The following functions are changeable: Brightness CM/INCH Touchtone ON/OFF Language
- Press START J backgauge G moves
to the rear and searches for the reference position, wait until a measurement is shown in the display 4860 = 45.00 cm, 17.717 inches 5260 = 52.00 cm, 20.742 inches 6660 = 61.00 cm, 24.016 inches
- The DIN and free programmable measurements are recallable with the respective buttons . Memory 1: A2, A3, A4, A5, Memory 2: A6, A7, B3, B4 Memory 3: Memory 4: and in inch Memory 1: 4¼“, 5 ½“, 7“, 8 ½“ Memory 2: 11“, 12“, 14“, 17“ Memory 3: Memory 4: In memory 3 + 4 (mm and inch) no measurements are saved. Until a first input of data the following will be shown in the corresponding fields: . The measurements entered remain stored. They cannot be deleted but overwritten.
Page 23 of 53

Text on page 24
How to program Memory 3 and 4 to enter the Press the memory button memory platform (3 or 4). Enter the required measurements or overwrite them.Press the button and keep it pressed until an acoustic signal sounds, the measurements have been saved now.
Warning! Before storing or cutting a measurement please check if the correct measurement scale (cm or inch) see above is stored. For information on how to store see picture below left Is shown on the screen see .
After 30 minutes the screen switches to energy-saving mode The screen is reactivated by touching the keypad area .
Page 24 of 53

Text on page 25
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Cutting activation Warning!
- Run backgauge to the front for turning the paper stack
- Do not interrupt the upward movement of the blade by performing switching procedures
- Wait until the display is green before activating a cut
- Blade must always be at the top and be covered by the clamp. Do not touch the blade (see safety information on page 38). Risk of injury!
Cutting to specified dimensions
- Press MAN.
- Enter dimension on the numerical key pad Measurement is shown in red (If a wrong dimension is entered this can be corrected by pressing the Y button)
- Press START dimension is approached, Measurement is shown in green
- Insert paper and move by means of the to the backgauge and stacking angle side lay on the left
- Release the cut.
Cut according to markings
- Press MAN.
- Adjust the backgauge with the hand-wheel to the back
- Insert paper and move by means of the to the backgauge and stacking angle side lay on the left
- Turn the hand-wheel to the right until the marking on the paper to be cut is below the cutting line indicator
- The further the hand-wheel is turned to the right, the quicker the backgauge moves. If the hand-wheel is turned to the left the backgauge will return quicker.
Page 25 of 53

Text on page 26
Eject function If EJECT is pressed instead of START , after inserting the measurement , the backgauge will advance forwards so that paper can be removed. Finally the backgauge moves to the last setting.
- Enter the start dimension on the display L
- Advance to the measurement with the
START
- Push the paper to the backgauge
- Press multiple cut
- Multiple cut sign appears top left together with the value 00.00
- Enter multiple cut measurement (appears in red letters)
- Press START the backgauge advances by the multiple cut size
- This is repeated everytime a cut is activated.
Exiting program-mode
- Press multiple cut (yellow). Multiple cut sign and value are deleted.
Calculator function
- Press CALC , calculate the desired and measurement, e.g. 40 - 2 = the backgauge advances immediately to 38.
- With the key < can be changed to manual mode MAN. at any time.
Page 26 of 53

Text on page 27
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Programming This control system enables you to store 99 programs with 99 programmable steps. One step represents one measurement. After entering the program numbers you are able to change between several program steps with the button j and b . = program number. First figure on display = program Second figure on display step. Smallest cutting measurement: 4860 3.50 cm / 1.378 inch 5260 3.50 cm / 1.378 inch 6660 2.50 cm / 0.984 inch
Each program step corresponds to one dimension. The indicated program step can be overwritten at any time. These programs remain stored when the machine is off.
- Press EDIT "Load program no."
- Enter program number 01 ... 99, with
on display = program (Top number number)
- If measurement is shown on the display the program is reserved, select another program
- Program step "01 Step" 00.00 appears. = program step. (Second figure on display
- Enter dimension, or move the backgauge to the desired measurement with the hand-wheel
- Store the measurement ,next program step appears.
- Enter the next measurement and with Enter store the measurement etc.
- Should the entered program be required immediately press RUN
- Press Enter
- Press START
- Escape the program mode press MAN.
Cancel a program
- Press EDIT
- Scroll with PRG until "Delete program no." appears
- Enter Program number
- Press Enter
- Press Enter .
Page 27 of 53

Text on page 28
Calculator function in programming
- Press EDIT
- Enter program number
- Enter the 1st program step e.g. start-up measurement 40 cm
- Store the measurement with enter
- Press CALC , calculate the desired , the measurement e.g. 40 - 2 = calculated measurement 38 flashes.
- Pressing the Enter-key again, the calculated measurement is saved in the corresponding step.
- With the key < it can be changed to programming EDIT at any time.
Page 28 of 53

Text on page 29
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Adapting a program when the printer’s imprint deviates
- Press RUN "Load program no." appears
- Enter program number 01 ... 99, and with 2 x Enter proceed to Step 1
- Correct the cutting position of the backgauge with the hand-wheel
- MODIFY appears on the screen and the measurement flashes
- To store press MODIFY
- Release a cut and turn the paper
- If the printer’s imprint deviates it can be corrected during the first two cuts via the hand-wheel – see above
- Correction is only possible during the first two cuts
- After leaving the RUN mode the original data is stored again.
Delete a step
- Press EDIT
- Enter program number, confirm with Enter
- Select program step with the arrow keys b and j
- Scroll with STEP until "Delete step no." appears, Press 2 x Enter .
Insert a step
- Press EDIT
- Select a program, confirm with Enter
- Scroll with STEP until "Insert step no." appears
- Enter insert position e.g. 02
- Confirm with Enter
- Enter a measurement
- Store the measurement with
- The cutting position can be shown on the screen with the arrow keys b and j .
Changing a program step
- Press EDIT
- Select a program, confirm with Enter
- Scroll with STEP until "Load step no." appears
- Enter step position e.g. 03
- Confirm with Enter
- Enter a new measurement, Store the measurement with .
Page 29 of 53

Text on page 30
Eject function program
- If a short measurement e.g. 30 cm and then a long measurement e.g. 40 cm is cut at the start of a program then it is wise to insert an after the first cut so that the paper EJECT is pushed to the front.
- The EJECT function can be added each time a measurement is entered and ejects before advancing to the next measurement. When the eject function is programmed an "E" appears top right in the display.
- Inserting an Eject function subsequently in the program. Select a program and advance to the step to be changed with the arrow keys b and j Enter the new measurement and press before activating the enter button . EJECT
Example of a program eject function
- Press EDIT
- Enter program number e.g. 08
- Press Enter
- 1. Enter program Step e.g. 30 cm
- Press Enter
- 2. Enter program Step e.g. 40 cm store the Press EJECT and with Enter dimension.
How the example works
- Press RUN
- Enter program number 08
- Press Enter ,
- Press START, Measurement is approached
- Insert paper
- Release cut 1
- Eject (Ejection is completed, turn the paper)
- The backgauge moves to program step 2
- Release cut 2
Multiple cut program
- Press EDIT
- Enter program number
- Enter the 1. program step e.g. start-up measurement 40 cm
- Store the measurement with Enter
- Press the multiple cut symbol
- Enter the number of cuts with the + button (max. 15 cuts) followed by the multiple cut size (cutting width).
- Store with Enter .
Page 30 of 53

Text on page 31
- Blade and cutting stick replacement •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
If the cutting quality decreases:
- Check the cutting depth (see page 38).
- Check the cutting stick (see page 34).
- Replace or grind the blade (see page 30 - 38). The blade cannot be ground if the blade height is less than 83 mm / 3,29 inches. A new blade must be used. The blade may only be ground by a qualified supplier or from the manufacturer Krug & Priester, D-72336 Balingen.
Danger! Risk of injury! The blade is extremely sharp. Do not extract or transport the blade without protection. Changing the blade may only be performed by trained staff.
Page 31 of 53

Text on page 32
- Blade and cutting stick replacement •
Turn the blade depth adjustment screw to the left until it stops. (Screwdriver found in tool set (A)) or tool holder (B).
Lower the blade by pressing both cutting actuators (1.). Keep one actuator pressed and turn off the main switch (2.).
Page 32 of 53

Text on page 33
- Blade and cutting stick replacement •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
The 3 eccentrics are now exposed and should be turned counter clockwise to position "0" with the special wrench and attachable extension pipe (A) (in the tool set). The slot must correspond to position "0" (B).
Only 4860 Unscrew the blade screws (C) on the right hand side.
Remove the special wrench and turn on the main switch until the blade returns to the home position.
Page 33 of 53

Text on page 34
- Blade and cutting stick replacement •
Position the main switch to "0" (1.) Remove the 2 blade screws on the elongated holes (2.). Then put the blade changing tool
- into place and fasten it to the blade (3.).
Remove 2 blade screws 4860 and 3 blade screws 5260, 6660 (1.). Loosen the grips (2.) of the blade changing tool (A) lightly and allow the blade to be taken downwards out of the machine (3.). Place the blade into the blade carrier (B) and screw it into place (4).
Page 34 of 53

Text on page 35
- Blade and cutting stick replacement •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Take out the cutting stick with a small screwdriver. If needed the cutting stick can be turned or exchanged. (The cutting stick can be used eight times).
Replacing the cutting stick (not the blade).
- Turn the blade adjusting screw (A) to the left until it stops. (Otherwise the first cut will be too deep).
- Remove the cutting stick according to top picure.
- Turn the cutting stick (the non-used side must be near to the blade) and plug it into the holding bolt. Danger! Risk of injury!
Cutting test after replacing the cutting stick (not the blade)
- Insert the paper and release the cut.
- If the last sheet of paper is not cut along the entire length turn the blade adjusting screw
- ¼ turn to the right.
- If the last sheet is still not completely cut repeat this process until the last sheet is cut along the entire length.
Page 35 of 53

Text on page 36
- Blade and cutting stick replacement •
Take the exchange blade carefully out of the blade box and screw it to the blade changing tool (A).
- Make sure there is a space ot 11 mm or 0.43 inches! (B).
- Blade must be covered! (C). Danger! Risk of injury!
11 mm 0.43 inch
Place the blade to be exchanged with the blade changing tool (A) mounted (1.), into the blade carrier and push it up to the top and screw it into place with the grips (2.).
Page 36 of 53

Text on page 37
- Blade and cutting stick replacement •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Lightly tighten 3 (4860 has 2) of the 5 blade screws with washers (1.). Remove the blade changing tool (2.). Lightly tighten the remaining blade screws with washers (3.). Return blade changing tool to tool holder (B).
Only 4860 Lightly screw in the right blade screw with the washer (A) when the blade is lowered.
Remove all tools and distribute paper along the entire cutting length (1.). Turn main switch to position "I" (2.).
Page 37 of 53

Text on page 38
- Blade and cutting stick replacement •
Lower the blade by pressing both cutting buttons (1.). Keep one button pressed and turn off the main switch (2.).
With the special wrench (A) the 3 eccentrics should be screwed down (3.)until the paper is cut along the entire length of the blade (The blade must remain parallel, not too deep into cutting stick).
Only 4860 Tighten the blade screws (A) on the right hand side.
Turn main switch to position "I" (1.). Blade will return to upper position. Tighten the blade screws (2.) firmly.
Page 38 of 53

Text on page 39
- Blade and cutting stick replacement •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Paper cutting test. If the last sheet or several sheets are not completely cut, gradually turn the knob for blade depth adjustment (A) ¼ turn to the right until the paper is cut along the entire length. Do not set too low as blade will become blunt sooner.
OK
Clamping
Danger by blade replacement! Blade must always be covered by the pressing bar (see picture below at the left).
Blade
OK
Page 39 of 53

Text on page 40
- Maintenance and cleaning •
Danger! Disconnect the mains before starting any service work or before removing the cover.
Maintenance work may only be performed by trained staff.
Grease the backgauge (A) control weekly with a grease gun. Advance the backgauge as far as possible to the front. (Use non-resinous oil or grease). Grease the remaining parts twice a year (see picture). The main switch must be on "0" (B). Remove lower panel (C). Tools in tool set or tool holder.
- Remove any paper.
- Grease the machine.
- Check the 4 joining bolts and 2 pushing bars for wear (D). If necessary inform your service personnel.
- Mount the machine.
= Greasing points on the machine.
Page 40 of 53

Text on page 41
- Maintenance and cleaning •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Annual inspection To maintain the operational safety and to prevent premature wear, we recommend an annual inspection and maintenance of the machine by a qualified service technician.
Krug & Priester GmbH & Co. KG 72336 Balingen - Germany
Parts & Service HOTLINE
Germany: +49 7433 2690 France: +33 3 8820 5435 North America: +1 843 552 2700 All other countries: Please contact your local distributor www.krug-priester.com
Safety test The safety regulations are according to the regulations of the country where the cutting machine is operated. The manufacturer recommends a safety check is made every 5 years by an authorised service team.
Page 41 of 53

Text on page 42
- Possible malfunctions •
Machine does not function!
Is the machine plugged in?
Main switch to position "I"? (A) Control system activated? (B) (Turn key to the right) Release a cut see page 21.
Page 42 of 53

Text on page 43
- Possible malfunctions •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Machine turns off:
- Machine overloaded. Safety button (A) or (B) ejects. (Allow 1 minute cooling time and reset the safety button (A) or (B).
- Machine blocked.
- Blade is blunt.
Eliminate the cause, and push the safety button (A).
- Backgauge blocked
Safety button (C) ejects. Eliminate the cause, and push the safety button (C).
Safety button for:
A = Blade drive
B = Clamping drive
C = Backgauge drive
Page 43 of 53

Text on page 44
- Possible malfunctions •
Does not cut through the last sheet:
- Turn or turn around the cutting stick (A), readjust the blade by means of the blade adjusting knob (B) (see page 38).
Poor cutting quality or blade stays in the paper stack.
- Change the blade (C) (see pages 30 - 38).
Page 44 of 53

Text on page 45
- Possible malfunctions •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Display illumination off
- Machine is plugged in? (A)
- Main switch on position "I"? (B)
- Push in the safety button! (C)
- Check the units fuse and the on-site circuit breaker!
After 30 minutes the screen switches to energy-saving mode The screen is reactivated by touching the keypad area .
Trouble shooting-light beam Cut cannot be activated:
- Remove all items obstructing the safety area (A)
- Transmitter and receiver both have a display (B) Green = o.k. / ready for operation Red = light beam is interrupted or error
Page 45 of 53

Text on page 46
- Possible malfunctions •
Motor runs but blade does not move downwards.
- Security brake has been activated! Inform the Service Team!
IDEAL
"Service"
None of the above mentioned methods helped to solve the problem: Contact Service Team under
- www.krug-priester.com "Service" service@krug-priester.com
Page 46 of 53

Text on page 47
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
Recommended accessories:
Blade
- No. 9000 021
- No. 9000 130
- No. 9000 025
Cutting stick (6 pieces)
- No. 9000 022 4860
- No. 9000 024 5260
- No. 9000 026 6660
Blade changing tool 1
- No. 9000 523 4860
- No. 9000 524 5260
- No. 9000 526 6660
Paper knock-up block 1
- No. 9000 521
Side tables left and right
- No. 9000 528
Page 47 of 53

Text on page 48
- Technical data •
Technical data:
- Power supply: 230V/50Hz/1~, 120V/60Hz/1~
- Cutting height: 80 mm
- Leakage current < 3,5mA
- Power cord gauge min. 1,5mm 2 (230V)
- Power cord gauge AWG 12 (20A) (120V)
The exact technical specifications can be found on the technical specifications sticker
- on the machine. A wiring diagram is found in the electrical switch box.
To claim under guarantee, the machine must still carry its original identification label.
Safety light beam
- Total reaction time: 101 ms
- Resolution 25 mm/minimum distance: 290 mm
Ambient operating temperature 10°C - 60°C Air humidity (not condensating) 15 % - 95 %
Cuttinglength mm
Tabledepth mm
Minimum space requirement (WXDXH) mm
Weight kg
with side tables: (Width) 4860 1349 mm
- * with side tables: (Depth) 4860 992 mm
- with side tables: (Width) 5260 1436 mm
- * with side tables: (Depth) 5260 1126 mm
- with side tables: (Width) 6660 1565 mm
- * with side tables: (Depth) 6660 1220 mm
- ** with side tables: 4860, 241 kg
- ** with side tables: 5260, 266 kg
- ** with side tables: 6660, 321 kg
Page 48 of 53

Text on page 49
- Technical data •
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
This machine is approved by independent safety laboratories and is in compliance with the EC-regulations 2006/42/EG and 2014/30/EG.
Sound level information: Sound measurement to EN 13023 : 72,5 db (A)
Subject to alteration without notice.
Page 49 of 53

Text on page 50
- Technical data •
The company Krug + Priester has the following certifications:
- Quality management system according to DIN EN ISO 9001:2008
- Environmental management system according to DIN EN ISO 14001:2009
- Energy management system according to DIN EN ISO 50001:2011
Page 50 of 53

Text on page 51
IDEAL 4860 • IDEAL 5260 • IDEAL 6660
DE EN FR
EG-KONFORMITÄTSERKLÄRUNG
EC-declaration of conformity Déclaration de conformité CE
- Hiermit erklären wir, daß die Bauart von
- Herewith we declare that
- Par la présente, nous déclarons que
GS-ID Nr. 11486001 11526001 11666001
UL-ID Nr. 10486001 10522102 10655002
- folgenden einschlägigen Bestimmungen entspricht
- complies with the following provisons applying to it
- sont conformes aux dispositions pertinentes suivantes
2006/42/EG: Maschinenrichtline, EC Machinery directive, EC Directives machines. 2014/30/EU: EMV Richtline, EMV Electromagnetic compatibility directive, EMV directives compatibilité électromagnétique. 2011/65/EU RoHS Richtlinie, RoHS directive, RoHS directives.
- Angewendete harmonisierte Normen insbesondere
- Applied harmonised standards in particular
- Normes harmonisées utilisées, notamment
EN 60204-1; EN 1010-1; EN 1010-3; EN ISO 12100; EN ISO 13857; EN ISO 13849-1; EN 13023; EN ISO 11204; EN 61496-1; EN 61496-2; EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
01.11.2014 Datum
Bevollmächtigter für technische Dokumentation Authorized representative for technical documentation Représentant autorisé pour la documentation technique
Krug & Priester GmbH u. Co KG Simon-Schweitzer-Str. 34 D-72336 Balingen (Germany)
Page 51 of 53

Page 52 of 53

Text on page 53
IDEAL • Made in Germany
- Document Shredders •
- Trimmers and Guillotines •
Page 53 of 53 · End of manual
Quick start
- Set up: remove the stand from the wooden pallet. Use 4 strong people to lift the machine onto the stand, secure it with the 4 screws, and put the shelf on the stand.
- Connect power: plug the machine directly into a single phase socket (230V / 10A min or 115V / 15A min) and keep free access to the mains.
- Check the safety devices: before each use, make sure all covers and the safety beam guard are mounted. Hold the test rod in the protective field. An active work cycle must stop immediately.
- Start up: set the main switch to "I", insert the key and turn it to the right, then press START. The backgauge moves to the rear to find its reference position.
- Set the measurement: press MAN, enter the dimension on the keypad, and press START. Wait until the measurement shows in green before cutting.
- Load the paper: place the stack against the backgauge and the side lay. Use the paper knock-up block to move stacks, and run the backgauge to the front to turn the stack.
- Cut: press both actuators of the two-handed control at the same time and hold them until the paper is completely cut. Release both actuators to stop.
- Shut down: when the machine will not be used for a longer period, set the main switch to "0".
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not function | Not plugged in, main switch off, or control system not activated | Check the plug, set the main switch to "I", and turn the key to the right. Page 42 |
| Machine turns off during a cut | Machine overloaded, blocked, or the blade is blunt, so the blade or clamp safety button ejects | Eliminate the cause, allow 1 minute cooling time, and push the safety button back in. Page 43 |
| Backgauge stops and its safety button ejects | Backgauge blocked | Eliminate the cause and push in the backgauge safety button (C). Page 43 |
| The last sheet is not cut through | Worn cutting stick or blade depth too shallow | Turn or turn around the cutting stick, then turn the blade depth knob ¼ turn to the right at a time until the last sheet is cut. Page 44 |
| Poor cutting quality or the blade stays in the paper stack | Blunt blade | Change the blade. It cannot be ground if the blade height is less than 83 mm / 3.29 inches. Page 44 |
| Display is dark | No power, safety button out, or energy-saving mode | Check the plug, the main switch and the safety button, then the unit fuse and circuit breaker. After 30 minutes the screen goes into energy-saving mode. Touch the keypad to wake it. Page 45 |
| Cut cannot be activated | The safety light beam is interrupted (red display) | Remove all items from the safety area until the transmitter and receiver displays show green. Page 45 |
| Motor runs but the blade does not move down | The security brake has been activated | Contact the service team. Page 46 |
Frequently asked questions
How many cutting programs can I store?
The control stores 99 programs with 99 programmable steps each, and one step is one measurement. Programs stay stored when the machine is off. See page 27.
What is the smallest cut and the cutting height?
The smallest cutting measurement on the 5260 is 3.50 cm / 1.378 inch, and the cutting height is 80 mm. See page 27, page 48.
Does it have preset paper sizes?
Yes. Memory 1 and 2 hold DIN sizes (A2 to A7, B3, B4) and inch sizes (4¼", 5 ½", 7", 8 ½", 11", 12", 14", 17"). Memory 3 and 4 are for your own measurements, which you can overwrite but not delete. See page 23, page 24.
Can it make several equal cuts automatically?
Yes. Use the multiple cut function: after the start dimension, enter the multiple cut size and press START, and the backgauge advances by that size after every cut. In a program you can set up to 15 cuts. See page 26, page 30.
