W-500L User's Manual, page 1

Page 1 of 4

W-500L User's Manual, page 2
Text on page 2

L- BAR IMPULSE SEALER

TROUBLESHOOTING

MALFUNCTIONS

REASONS

SUGGESTIONS

No sealing Power lamp is off

Disconnected plug Power cord is broken Transformer is broken

Check or change the plug Replace or repair the cord Replace the transformer

No sealing Power lamp is on Sealing lamp is on

Heater (heating element) is broken Spring hook our mounting spring is loose or in poor contact Terminals of the heating element are in poor contact

Replace the heater Clean or tighten spring hook connection Clean the terminals and adjust if needed

No sealing Power lamp is on Sealing lamp is off

Microswitch is activated Defective microswitch

Adjust the microswitch lever Adjust the microswitch position Replace the microswitch

Timer malfunction Prolonged heating time

Replace timer or relay Decrease the timer setting

Replace the Teflon adhesive

Heating timer is set too high Cooling time is not enough

Lower the timer setting Continue pressing the upper lever for 1-2 seconds after the light goes off

Worn Teflon cloth Worn silicone rubber

Replace Teflon cloth Replace silicone rubber

Sealing time is too short

Dirty Teflon cloth Dirty sealing bar

Clean the Teflon cover Clean the silicone rubber sealing bar

OPERATING INSTRUCTIONS MODEL

W-350L, W-500L, W-650L

Page 2 of 4

W-500L User's Manual, page 3
Text on page 3

IMPORTANT POINTS TO REMEMBER

SPECIFICATIONS

Model Power Sealing Length Seal Type Weight (lbs)

W-350L 110V/1000W 14" x 20" Round 80, 18

W-500L 110V/1900W 20" x 26" Round 98, 21

W-650L 110V/2800W 26" x 31" Round 116, 22

OPERATING INSTRUCTIONS

Read all instructions before use. Save these instructions for later use.

Follow all warnings and instructions marked on the product.

Unplug this product from the power source before cleaning and/or changing any parts

Do not rest anything on the power cord. Do not place the machine where the power cord may be stepped on or pulled.

Always keep out of reach of children and pets.

This sealer should only be in use with an operator in attendance.

Before operating, check the heating element, Teflon cover, Teflon adhesive and sealing pad (silicone rubber).

Never insert clothing, hands, fingers between the sealing jaws of sealers.

Set the Power Switch to the ON position.

Adjust the timer setting according to the thickness of the sealing material. Note: Always start with the lowest setting and gradually increase to the correct setting.

Never touch the heating elements with bare hands while the sealer is plugged into a power source, or in operation, or just finished operation. It will be HOT.

Pull the film to be sealed in between the base and sealing jaw.

Place the object to be sealed between the sheets of film.

Press the sealing bar down and seal.

Wait 2-3 seconds to allow the seal to set and lift the handle.

Seal the opening of the film.

Use the heat gun to shrink the film evenly.

Be sure to check for worn parts before starting operation.

Do not operate with a damaged power cord or plug.

Always keep the unit clean. Do not use water. Silicone spray may be used to clean the unit. Be sure the unit is unplugged from the power source before cleaning.

When changing blade (for sealers with cutters), be careful of the sharp edge.

When changing the teflon adhesive, be sure the entire surface under the heating element is covered with a teflon adhesive. Bend down the excess teflon adhesive on both ends. This prevents the heating element from breaking and the machine from grounding.

When replacing the fuse, be sure the exact voltage and ampere is used.

Be sure to keep a record of your model number. Specify this number when ordering parts.

When replacing any parts, be sure to mark down the exact locations of the connections.

Page 3 of 4

W-500L User's Manual, page 4
Text on page 4

ADDITIONAL INFORMATION

Always unplug the unit from the power source before attempting any maintenance.

Always keep the sealing platform clean and remove any residue found on the platform and Teflon tape. Silicone spray may be used for this purpose.

When replacing the Heating Element, always check the condition of the Teflon Tape.

Occasionally check the condition of the Silicone Rubber for wear and burn. A damaged or worn Silicone Rubber will affect the quality of the seal.

CONNECTION DIAGRAM

PARTS DIAGRAM

Contact your distributor for spare parts diagram.

Page 4 of 4 · End of manual

Quick start

  1. Check the heating element, Teflon cover, Teflon adhesive and silicone rubber pad before use.
  2. Set the power switch to ON.
  3. Set the timer for the material thickness, starting at the lowest setting and increasing gradually.
  4. Pull the film between the base and sealing jaw and place the object between the film sheets.
  5. Press the sealing bar down, wait 2–3 seconds for the seal to set, then lift the handle.
  6. Seal the opening of the film, then shrink the film evenly with a heat gun.

Troubleshooting

ProblemLikely causeFix (from the manual)
No sealing, power lamp offDisconnected plug, broken power cord or broken transformer.Check or change the plug, replace or repair the cord, or replace the transformer. Page 2
No sealing, power lamp and sealing lamp onBroken heating element, loose spring hook or mounting spring, or poor contact at the heating element terminals.Replace the heater, clean or tighten the spring hook connection, and clean and adjust the terminals. Page 2
No sealing, power lamp on but sealing lamp offMicroswitch is not activated correctly or is defective.Adjust the microswitch lever or position, or replace the microswitch. Page 2
Poor seal qualityWorn Teflon cloth or worn/burned silicone rubber.Replace the Teflon cloth or silicone rubber. Page 2

Frequently asked questions

What are the W-500L specifications?

110V/1900W with a 20" x 26" sealing length and round seal type. The W-350L is 110V/1000W, 14" x 20", and the W-650L is 110V/2800W, 26" x 31". See page 3.

How do I set the sealing time?

Adjust the timer to the thickness of the material. Always start at the lowest setting and increase gradually. See page 3.

How do I clean the sealer?

Unplug it first. Do not use water; silicone spray may be used to clean the unit, sealing platform and Teflon tape. See page 4.

What should I check before each use?

Check the heating element, Teflon cover, Teflon adhesive and silicone rubber sealing pad for wear. See page 3.

How do I replace the Teflon adhesive?

Cover the entire surface under the heating element with Teflon adhesive and bend the excess down at both ends to keep the element from breaking or grounding. See page 3.