

Page 1 of 2

Text on page 2
Installation Instructions
WallTac ™ and ReTac Wall
Print Media
To ensure proper usage of WallTac™ and ReTac® Wall printable media, please follow the recommendations listed below.
- The wall where the graphic is to be installed must be a clean, painted surface, free of chips and defects. Dust, dirt and oil will prevent proper adhesion. Defects and dirt on the surface may show through the image. A damp sponge and lint-free cloth can be used to clean the surface before applying the graphic. The wall must be clean and dry before the graphic can be installed.
- WallTac™ and ReTac® Wall graphics are recommended for indoor use on fl at wall surfaces. WallTac™ and ReTac® Wall are not recommended for use on outdoor or textured surfaces.
- Allow at least 10 days for freshly painted surfaces to cure. Outgassing of freshly painted surfaces may contribute to failure of adhesion.
- Always consider the location of the graphic when applying it to the wall. Small children may pick at the graphics, causing failure and potentially creating a choking hazard.
Application and Removal Instructions
- The size of the WallTac™ or ReTac® Wall graphic aff ects the method of application.
- For smaller graphics, remove the release liner found on the rear of the print to expose the adhesive. For larger graphics, pull back 3” of the release liner on the top of the graphic to expose a small amount of adhesive. Crease the release liner to create a hinge that holds the exposed adhesive away from the wall in order to line up the top edge.
- Position the graphic in the intended location, using a squeegee to apply the top of the graphic and working down to remove the air as the graphic is applied from the center outward.
- Remove any air bubbles that may remain by pushing them out toward the edges of the graphic with the squeegee. Ensure the wall graphic is attached fi rmly to the wall surface, especially around the edges.
- The WallTac™ or ReTac® Wall graphic can be removed by pulling an edge back between 120° and 180° and using a smooth continuous motion.
IMPORTANT NOTE:
Please refer to the WallTac™ and ReTac® Wall TDS and MSDS for more information.
The technical information, recommendations and other statements contained in this document are based upon testing and experience Drytac believes to be reliable, but the accuracy and or completeness is not guaranteed. Drytac recommends a small test be performed to determine suitability beforehand. This document does not constitute a warranty of any kind.
Drytac Corporation Drytac Canada Inc. Drytac Europe Ltd.
5601 Eastport Boulevard 105 Nuggett Court Filwood Road
Richmond, VA 23231 Brampton, Ontario L6T 5A9 Fishponds, Bristol BS16 3RY
United States Canada United Kingdom
customerservice@drytac.com toronto@drytac.com bristol@drytac.com
Rev October 2014
Recommendations for Installation
- Non-porous painted walls provide optimal surfaces for WallTac™ and ReTac® Wall adhesion. Any cracks or chips must be repaired beforehand. Semi-gloss and gloss paint fi nishes are recommended.
Page 2 of 2 · End of manual
Quick start
- Make sure the wall is clean, dry and painted, free of chips and defects; clean it with a damp sponge and lint-free cloth.
- Let freshly painted walls cure for at least 10 days.
- For small graphics, peel off the whole release liner. For large graphics, pull back 3" of liner at the top and crease it into a hinge.
- Line up the top edge, squeegee the top in place, then work down and from the center outward to remove air.
- Push any remaining bubbles to the edges with the squeegee and press the edges down firmly.
- To remove, pull an edge back at 120° to 180° in a smooth, continuous motion.
Frequently asked questions
Can WallTac or ReTac Wall be used outdoors or on textured walls?
No. They are recommended for indoor use on flat wall surfaces only. See page 2.
How long should fresh paint cure before applying?
At least 10 days, since outgassing from fresh paint can cause adhesion failure. See page 2.
What paint finish works best?
Non-porous painted walls with semi-gloss or gloss finishes. Repair cracks or chips first. See page 2.
How do I remove a WallTac or ReTac Wall graphic?
Pull an edge back between 120° and 180° using a smooth, continuous motion. See page 2.
