We're sorry, but we no longer offer this item.
Call us at 1-800-944-4573 for personalized recommendations
check out these similar items that may be a good fit
Product Description
This Mactac Permacolor Enhancers Clear 54" x 50' Silver Metallic Gloss Overlaminate is a 3.0 mil cast laminating film with a high concentration of light refracting silver metallic flakes for a glistening and sparkling appearance on the surface of your substrate or to use as an overlaminating film to greatly enhance your high quality graphics. This film is designed for high profile applications over flat to slightly curved surfaces. It is coated with a high-performance permanent, clear solvent acrylic adhesive protected with 78# bleached white kraft liner for good stability and layflat. Add sparkle to your graphics and wraps with Mactac Permacolor Enhancers 3mil Clear 54" x 50' Silver Metallic Gloss Overlaminate.
Product Details
- Features and Benefits:
- Five year outdoor durability
- Two enhancers finishes
- Typical Uses:
- Overlaminate - flat, slightly curved applications
- Vehicle, fleet and marine graphics
- Colored vinyl enhancement
- General signage
- Use with: B•free Gruv GVC929, B•free Gruv GV729, MACmark 6600, MACmark 9800 and Any graphic print for special effects finish
- Typical Applications
Logos Equipment identification Automotive applications Container decals Fleet marking General signage - Physical Properties
Property Typical Values Test Method Thickness, inches (µm)
Film plus adhesive
Crystal
Silver
0.0037 (94)
0.0042 (107)ASTM D-645 Peel Adhesion
180° on Stainless Steel
-20 min
- 24 hrs.
2.8 (12.7)
4.0 (17.8)ASTM D-903 Face Material Data, 68°F (20°C)
Tensile strength lb. /in. (N/m)
Elongation %
>7.5 (1300)
>120%DIN 53455 Dimensional Stability
(shrinkage) in Percent< 0.10 10" x 10" Sample
Bonded on aluminumTemperature Ranges
Application:
End Use:
40° to 104°F (5° to 40°C)
-50° to 225°F (-45° to 107°C) - Shelf Life
Two years when stored between at 60- 80°F (15 - 25°C) and 50% relative humidity or less. - Durability
This product is good for 5-year in outdoor durability. This use-life estimate is based upon accelerated age studies based on vertical applications under “normal” temperate climates. Please note that exposure to severe temperatures, ultra-violet light and also tropical, sub-tropical or desert regions will cause more rapid deterioration. This also applies to polluted areas, high altitude and south facing exposure. - Chemical Resistance
A sample is prepared in the same manner as for the Chemical Resistance Test and is immersed in the test fluid followed by drying at each stage.
Test Fluid Observation Gasoline (30min) No Effect Distilled Water (24 hrs.) No Effect SAE 20 Motor Oil (1 hr.) No Effect 10% HCL (10min) No Effect 10% NH4OH (10 min) No Effect - Limitations
1) The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
2) If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
3) If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
- Recommendations
1. Where exposure to moisture, chemicals, solvents or high pressure wash is anticipated, Mactac recommends sealing the edges with varnish, silicone or other sealant to prevent penetration by these liquids.
2. Overlaminates should not be applied onto dusty or dirty prints.
3. The mounting board must be properly prepared prior to mounting the image. This may include wiping with alcohol, light sanding or surface sealing depending on the board. Contact your board supplier for their recommendation.
4. Mactac's pressure sensitive mounting films are intended for "Cold Roll Lamination" (40°F - 104°F). The addition of heat while simultaneous mounting with Thermal Overlaminates may result in curl or have other detrimental effects on the finished product.
5. Whenever possible, always test first to ensure end-use capability.
- Application Tips
Used as cut vinyl - Application of 6300 when used as cut-vinyl is made easier if Mactac prespacing tape is used, or can be applied as an overlaminating film with a standard laminator. Where exposures to chemical and solvent spills are likely to occur, edge sealing of decals with a varnish or clear coat will prevent edge lift. Correct varnishing of decals gives greater protection and longer end-use life against any prolonged effect of weathering, abrasion and other erosive effects such as frequent cleaning.
Used as an Overlaminate for Vehicle Wraps - Because this is a much thicker overlaminate Mactac offers a limited warranty on flat to slightly curved surfaces. There is no warranty for Enhancers on motor vehicle wraps, over rivets and corrugations, through complex surfaces or for marine graphics. - Values given are typical and are not necessarily for use in specification.
Specifications
- Adhesive Type: Permanent Acrylic
- Color: Clear
- Films: Cast Vinyl (PVC)
- Finish: Crystal High Gloss
- Length: 50'
- Width: 54"
- Liner Category: 78# White Kraft
- Outdoor Durability: 5 Years
- Precise Program: N
- Thickness: 3.0 mil
Technical Assistance Guide
Cleaning Overlaminated ImagesCold Roll Lamination Procedure
Rolling And Shipping Laminated Images
Surface Preparation
Bfree Watercraft Application
Subscribe to Get Exclusive Offers!
Receive a 10% off coupon for just signing up.
Partners
Copyright © 2026 MyBinding
