Morgana AutoFold-Pro User Manual, page 1

Page 1 of 44

Morgana AutoFold-Pro User Manual, page 2
Text on page 2

AutoFold Pro

DOCUMENT FOLDING MACHINE

OPERATORS MANUAL

ISSUE 1

MAY 2010

Page 2 of 44

Morgana AutoFold-Pro User Manual, page 3
Text on page 3

INDEX

INTRODUCTION & SPECIFICATION

The Morgana AutoFold Pro

PAGE

SAFETY Do’s & Don’ts

OPERATING THE AutoFold Pro Adjusting the Tilt of the Feed Bed Fitting the Transfer Bed Assembly to the Autocreaser and Aligning the Machines

TOUCHSCREEN OPERATION

Touchscreen Layout Paper Settings Page Roller Gap Set Page Feed Bed Fans Settings Page Fold Settings Pages Folds in ‘Set By Fold’ mode Folds in ‘Set By Position-’ mode Example of ‘Set By Position’ mode Delivery Settings Page Status Screen Running the Job Setting the machine to operate in manual sheet feed mode Store Pages Tools Menu

REMOVING PAPER JAMS

TROUBLE SHOOTING

Paper crease out of square Crease Position Inaccuracy Paper fold out of square Paper Jamming Machine will not start Paper not feeding Cracking of the printed material along the crease

FOLDING

Page 3 of 44

Morgana AutoFold-Pro User Manual, page 4
Text on page 4

AutoFold Pro

INDEX

ERROR SCREENS

01 Sheet did Not Arrive 02 Paper Crunch 09 Clip 1 NOT Clear 10 Clip 1 NOT Blocked 11 Clip 2 NOT Clear 12 Clip 2 NOT Blocked 13 Overlap 45 Sheets Too Close

DISPATCH KIT

ACCESSORIES AND OPTIONS

RECOMMENDED SPARES

MACHINE CALIBRATION HISTORY SHEET

FUSE POSITIONS & RATINGS

PRODUCT RECYCLING AND DISPOSAL

SYSTEM

Page 4 of 44

Morgana AutoFold-Pro User Manual, page 5
Text on page 5

INTRODUCTION

AutoFold Pro

INTRODUCTION AND SPECIFICATION

The AutoFold Pro is a self powered, stand alone folding machine with an innovative new vacuum controlled sheet alignment system which has been designed to take pre-creased stock from a wide range of both Morgana and 3rd party creasing machines. The AutoFold Pro features the unique Flying Knife Folding System used successfully in the much acclaimed Digifold which allows folding of most stocks from 0.1mm, reducing the possibility of scratching, marking or cracking of the substrate as is often associated with conventional folding systems. A maximum paper thickness cannot be specified, as this is governed by the hardness of the substrate and the type of fold required; but in most cases stocks up to 0.35mm should present no problems providing they are properly pre-creased. It is IMPORTANT to note that to prevent cracking, when using dry ink or toner based print engines, the material must be fully acclimatised for at least 48 hours before putting an image onto the paper. IMPORTANT the operating environment should be controlled to a temperature between 16° C and 27° C Maximum.

Specification

Feeding System ................................................ Conveyor Vacuum Sheet Alignment Input Bed Height ...............................................Adjustable from 850mm to 1000mm Max. Sheet Size ................................................600mm x 385mm (24” x 15”) Min. Sheet Size .................................................210mm x 140mm (8.3” x 5.5”) (dependant on stiffness of paper and type of fold). Max. Paper Thickness ................................... 0.40mm (varies according to hardness, type of fold, and substrate). Min. Paper Thickness ....................................... 0.11mm (varies according to hardness, type of fold, and substrate). Max. No. Folds per Sheet.................................. 2 Max. No. Stored Programmes ...........................Unlimited Min. Repeat Fold Distance ................................70 mm (2.75”) (depending on paper weight) Min. Fold Distance from Leading Edge ............. 50mm (1.96”) (depending on paper weight) Min. Fold Distance from Tail Edge .................... 50mm (1.96”) (depending on paper weight) Min. Fold Length ............................................... 70mm (2.75”) Speed per Hour (A4 in half)............................... 6240 sheets (on speed 3, Pulsed) Note: The production speed varies according to the material size and the fold type. Dimensions ....................................................... L: 1700mm H: 1220mm W: 680mm L: (66.9”) H: (48”) W: (26.8”) Weight ............................................................... 128Kgs (+50Kgs packing) Power Requirement .......................................... 1 phase 220 / 240v

  • As part of our continued product improvement plan, specifications and information published in this manual are subject to change without notice.

All specifications are dependant on application, type of stock, temperature, RH and print engine used. Specifications quoted were measured on uncoated and unprinted stock. E & OE.

FOLDING

Page 5 of 44

Morgana AutoFold-Pro User Manual, page 6
Text on page 6

AutoFold Pro

Safety Do’s & Don’ts

Safety Do’s & Don’ts

REGLES DE SECURITE : « A FAIRE » ET « A NE PAS FAIRE »

Do - read this operator manual fully before operating the machine. Lire ce mode d'emploi avant d'utiliser la machine.

Do - operate with the designated AC current only. Use an exclusive outlet, as overloading may cause fire or an electric shock. Respecter l'alimentation électrique indiquée. Brancher sur une prise séparée car une surcharge peut entraîner un incendie ou un choc électrique.

Do - install the power cord out of the way to avoid a tripping hazard. Installer le cordon d'alimentation de manière à ne pas pouvoir trébucher par dessus.

Do - make sure that the mains inlet connector is always easily accessible. Ménager un accès libre à la prise de courant.

Do not - install the machine in an unstable place such that it tilts or shakes. Ne pas installer la machine sur une surface non plane, afin d'éviter qu'elle ne penche ou ne vibre.

Do not - unplug the plug or unplug the power cord from the outlet with a wet hand, this can cause an electric shock. Ne pas installer la machine sur une surface non plane, afin d'éviter qu'elle ne penche ou ne vibre.

Do not - unscrew and remove any covers from the machine, as it can cause an electric shock or injury. Ne démonter et enlever aucun carter de la machine, par crainte de décharge électrique ou de blessure.

Do not - place receptacles containing liquids on any surface. Ne pas placer de récipient contenant un liquide sur la machine.

Do not - adjust any part of the machine whilst rollers are running N'effectuer aucun réglage pendant que les rouleaux fonctionnent.

Do not - operate the machine with loose or trailing clothing or loose hair. Ne pas porter de vêtements flottants et rassembler les cheveux longs lors de l'utilisation de la machine.

Do not - under any circumstances adjust the paper gate when the machine is switched on. En aucune circonstance, régler le séparateur de papier lorsque la machine est branchée.

SYSTEM

Page 6 of 44

Morgana AutoFold-Pro User Manual, page 7
Text on page 7

Warning Labels

Do - be aware of any finger traps and rotating parts when operating the machine. Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do - read this operator manual fully before operating the machine. Lire ce mode d’emploi avant d’utiliser la machine.

Do not - operate the machine with loose or trailing clothing. Ne pas porter de vêtements flottants lors de l'utilisation de la machine

Do not - operate the machine with loose hair. Rassembler les cheveux longs lors de l'utilisation de la machine.

Do - be aware of any finger traps and rotating parts when operating the machine. Attention au risque de se coincer les doigts, et aux pièces en mouvement lors du fonctionnement de la machine.

Do - be aware of sharp points and blades. Attention aux éléments tranchants et aux couteaux.

Do - be aware of rotating rollers. Attention aux rouleaux en fonctionnement

Do - be aware of low current anti-static shock. Attention aux faibles chocs d'électricité statique

FOLDING

Page 7 of 44

Morgana AutoFold-Pro User Manual, page 8
Text on page 8

AutoFold Pro

AutoFold Pro

DOCUMENT FOLDING MACHINE

Key to photograph below

Delivery assembly Gap Set Knobs Mains Input Socket

Top Cover System Switch Emergency Stop Switch

Touchscreen Fuses

SYSTEM

Page 8 of 44

Morgana AutoFold-Pro User Manual, page 9
Text on page 9

Operating the AutoFold Pro

ADJUSTING THE TILT OF THE FEED BED

  1. The Feed Bed can be tilted, so that it matches the height of the creasing unit that is being used with it.

(i) Open the front and rear column covers. (ii) Loosen the knurled locking collars at the top of the front and rear gas springs. (iii) Adjust the tilt of the Feed Bed, (up or down) to match the height of the creasing unit, then re-tighten both of the knurled locking collars.

FITTING THE TRANSFER BED ASSEMBLY TO THE AUTOCREASER AND

ALIGNING THE MACHINES.

  1. The AutoFold is supplied, as standard, with a Transfer Bed Assembly that fits onto the AutoCreaser 33 and AutoCreaser Pro 33 machines. A Transfer Bed Assembly that will fit the wider AutoCreaser 50 and AutoCreaser Pro 50 machines can be purchased as an optional extra (see accessories and options on page 37).

(i) Remove the stacker unit from the AutoCreaser and fit the Transfer Bed Assembly as shown in FIG.8 (ii) Tilt the feed bed of the AutoFold, as described above, to align with the Transfer Bed Assembly as shown in FIG.8

FOLDING

Page 9 of 44

Morgana AutoFold-Pro User Manual, page 10
Text on page 10

AutoFold Pro

Operating the AutoFold Pro

(iii) Adjust the relative positions of the machines so that the Transfer Bed Assembly aligns with the Autofold Feed Bed as shown in FIG.9 (iv) Plug the connector, on the flying lead of the Transfer Bed Assembly, into the AutoFold Socket as shown in FIG.9. This electrical connection between the AutoFold and the AutoCreaser is a safety feature. If the system switch on the Autofold is switched off or a jam occurs on the AutoFold the AutoCreaser will stop feeding.

NOTE. When using the AutoFold with an AutoCreaser Pro 33 or an AutoCreaser Pro 50, it is recommended that the AutoCreaser is set to Pulse Feed and the speed is set to number 2. Depending on the type of crease and length of the paper, the speed setting may need to be changed to speed number 1 or number 3.

Align Machines As Shown

(FRONT VIEW)

AutoFold Feed Bed

AutoFold Socket

Morgana AutoCreaser Unit

AutoCreaser Transfer Bed Assembly

(TOP VIEW)

Align Machines As Shown

AutoCreaser Transfer Bed Assembly

AutoFold Feed Bed

SYSTEM

Morgana AutoCreaser Unit

Page 10 of 44

Morgana AutoFold-Pro User Manual, page 11
Text on page 11

Operating the AutoFold Pro

TOUCHSCREEN OPERATION

  1. Turn the Emergency Stop button clockwise to switch the power on. After the system start up procedure the touch screen will be displayed as shown below.

IMPORTANT.

If you have not been trained to operate this machine, we strongly advise that you select the red cross icon. We recommend that you either seek training or ask a trained operator to run the machine for you. Select the green tick icon only if you have been trained to operate this machine. If you have not been trained to operate this machine and you select the green tick icon, Morgana Systems Ltd accept no responsibility for personal injury, damage to the machine or damage to materials being processed by the machine.

The touch screen is laid out into 3 main areas as shown below:

Status of machine & data entry area. Also used for quick links to setting pages.

Setting page

Tabs to enable switching between setting pages - choose either Paper Settings, Gap settings, Feed Fan Setting, Fold settings, Delivery settings, Store and Tools.

FOLDING

Page 11 of 44

Morgana AutoFold-Pro User Manual, page 12
Text on page 12

AutoFold Pro

Operating the AutoFold Pro

Setting Pages.

Paper settings Page

Paper Type - As a guide choose as

Fold Selection - For quick setting of fold positions on standard size sheets

follows:

Highlighted fold is type currently selected, other folds may be selected Currently selected fold is shown in the status area.

0 - approx 0.1 thk

1 - approx 0.2 thk

Page Thickness - On selection of status area is replaced with a calculator for inputting new values

2 - approx 0.3 thk

3 - approx 0.3+ thk

Range = 0.1 to 0.4mm

Batch Button - Image is identical to that shown in the status area. On selection the status area is replaced with a calculator for inputting new values. Batch sizes of 1 to 998 may be set.

Arrows may be selected to increase or decrease the page size in 0.1mm increments

Paper Length - On selection the status area is replaced with a calculator for inputting new values. Length range = 190mm - 900mm

Paper size Selection.

Pre-set Paper sizes for

quick insertion - Standard

sizes for country origin

SYSTEM

Page 12 of 44

Morgana AutoFold-Pro User Manual, page 13
Text on page 13

Operating the AutoFold Pro

Pre-set Batch sizes for quick

Pre-set Paper Thickness sizes

FOLDING

Page 13 of 44

Morgana AutoFold-Pro User Manual, page 14
Text on page 14

AutoFold Pro

Operating the AutoFold Pro

Roller Gap Set Page.

To get to the roller gap setting page click the lower tab Roller gaps may be in the range of 0.05mm to 1.5mm, with increments of 0.05mm

for 2nd Fold Roller

for 1st Fold Roller

Recommended gap values -

based on paper thickness.

Setting the Roller Gaps (Gap 1, Gap 2 & Gap 3)

The roller gaps can be adjusted to suit the thickness of the material being folded; and the type of fold being produced. The roller gaps may also require adjustment if cracking of the print is noticeable. (see Fig 13.1 below).

FIG 13.1

INFEED

SYSTEM

Page 14 of 44

Morgana AutoFold-Pro User Manual, page 15
Text on page 15

Operating the AutoFold Pro

The gap settings (Gap 1, Gap 2 & Gap 3) can be adjusted by rotating the Roller Gap Set Knobs (see FIG 14.1 below).

IMPORTANT.

When setting roller gaps, you must first adjust the gap to a value greater than that required and then decrease the value to the required setting. (Do not set the gap, from a value lower than that required).

FIG 14.1

Roller Gap 3 Knob

Roller Gap 2 Knob

Roller Gap 1 Knob

PROCEDURE.

(i) Measure the thickness of the sheet using a Digital Vernier Calliper. (ii) Set roller GAP 1 to the vernier reading. (iii) Set roller GAP 2 and roller GAP 3, (for the type of fold being produced), using the GAP SET GUIDE table shown on next page.

FOLDING

Page 15 of 44

Morgana AutoFold-Pro User Manual, page 16
Text on page 16

AutoFold Pro

Operating the AutoFold Pro

GAP SET GUIDE

Half Fold on Knife 1 Half Fold on Knife 2

FOLD TYPE

Half K1 Half K2 Letter Concertina Gate Closed Gate Engineering Double

GAP 3 2X 2X 3X 3X 3X 3X 3X 4X

GAP 2 2X

2X

GAP 1

Example 1:- When producing a Half K1 fold, if GAP 1 is 0.2 (X) then set GAP 2 to 0.4 (2 x X) and set GAP 3 to 0.4 (2 x X). Example 2:- When producing a Gate fold, if GAP 1 is 0.3 (X) then set GAP 2 to 0.3 (X) and set GAP 3 to 0.9 (3 x X).

FOLD TYPES

HALF

LETTER

CONCERTINA

GATE

CLOSED GATE

ENGINEERING

DOUBLE

SYSTEM

Page 16 of 44

Morgana AutoFold-Pro User Manual, page 17
Text on page 17

Operating the AutoFold Pro

Feed Bed Fan Settings Pages.

To get to the fed bed fan setting page click the lower tab status area.

You can adjust the speed independently for the front and rear fans. On the optionally available long feed bed, a centre fan is also shown for adjustment.

Front fan speed adjust

Rear fan speed adjust

select from 0 - 1 - 2 - 3

select from 0 - 1 - 2 - 3

FOLDING

Page 17 of 44

Morgana AutoFold-Pro User Manual, page 18
Text on page 18

AutoFold Pro

Operating the AutoFold Pro

Fold Settings Pages.

To get to the Fold setting page click the lower tab

status area.

or

from the

If you have selected a predefined standard Fold Type from the paper settings page the crease positions will be set for you. These positions can be fine tuned by ± 0.1mm

increments by pressing the arrow buttons

for each crease.

Folds in ‘Set By Fold’ mode.

K1 Fold micro adjust - On selection the status area is replaced with a calculator for inputting new values.

Micro adjust range is -5.0 to +5.0 with increments of 0.1mm

Folding can be Micro adjusted for fine adjustment.

Micro adjust range is -5.0 to +5.0 with increments of 0.1mm

With Folding turned off the deflect positioned can be micro adjusted.

Folding on/off selector green is on & red is off.

Micro adjust range is -5.0 to +5.0 with increments of 0.1mm

SYSTEM

This is also indicated in the status area.

Page 18 of 44

Morgana AutoFold-Pro User Manual, page 19
Text on page 19

Operating the AutoFold Pro

Folds in ‘Set By Position’ mode.

Fold distance from lead edge for knives (K1 & K2)

K1 micro adjust selected

Clicking this icon switches deflect off &K1 returns to its original position.

K1 in deflect position.

This can be micro adjusted.

Micro adjust range is -5.0 to +5.0 with increments of 0.1mm

K1 & K2 in deflect position.

This can be micro adjusted.

Micro adjust range is -5.0 to +5.0 with increments of 0.1mm

FOLDING

Page 19 of 44

Morgana AutoFold-Pro User Manual, page 20
Text on page 20

AutoFold Pro

Operating the AutoFold Pro

SET BY POSITION

IMPORTANT NOTES.

  1. If the fold is too near, or on the center line of the crease; the fold will try to fold diagonally across the crease profile and pull the fold out of square to the paper.

The best fold squareness is achieved when the fold is not on the center line of the crease, it should be to one side of the crease center line as shown below.

Thus for a crease setting of 100 for example, the fold should be set to a figure slightly smaller or greater than 100.

center line of crease

  1. When using Set By Position, all dimensions are from the leading edge of the paper as shown in the example on page 20.

SYSTEM

Page 20 of 44

Morgana AutoFold-Pro User Manual, page 21
Text on page 21

Operating the AutoFold Pro

Example of Set by Position.

Paper Length = 350mm (13.8”)

SETTINGS

Crease 1 = 97.0mm (3.8”) Crease 2 = 179.0mm (7”) Crease 3 = 260.0mm (10.2”) Fold 1 = 179.0mm (7”) Fold 2 = 260mm (10.2”)

Crease 2 Fold 1

Crease 3 Fold 2

All dimensions are from the leading edge of the paper

Crease 2 = 179.0 Fold 1 (7”)

Crease 3 = 260.0 Fold 2 (10.2”)

9mm (0.35”)

FOLDING

Page 21 of 44

Morgana AutoFold-Pro User Manual, page 22
Text on page 22

AutoFold Pro

Operating the AutoFold Pro

Delivery Settings Page.

To get to the Delivery setting page click the lower tab

Roller position may be micro adjusted by clicking here.

Shingle may be micro adjusted by clicking here.

Delivery on/off status red is off green is on.

The Delivery can be toggled On or Off by clicking here.

SYSTEM

Page 22 of 44

Morgana AutoFold-Pro User Manual, page 23
Text on page 23

Operating the AutoFold Pro

Setting the Delivery Conveyor System.

WARNINGS:-

  1. The Machine will not start if the delivery unit is not in its up position.
  2. If the delivery is turned off the roller will feed to the far end of the belt conveyor and park there until turned on again.
  3. If the delivery is turned on when using the ‘Set by Fold’ mode of operation; the Roller Position and Shingle Length are automatically set, relative to the paper length and type of fold selected.
  4. When using the ‘Set by Position’ mode of operation; the Roller Position and Shingle Length must be adjusted manually to suit the job. (See FIG 20.1 below).
  5. When the optimum settings for the roller position and shingle length are achieved they can be stored with the job.

FIG 20.1

FOLDING

Page 23 of 44

Morgana AutoFold-Pro User Manual, page 24
Text on page 24

AutoFold Pro

Operating the AutoFold Pro

Status Screen.

Green icon indicates settings are saved - a red icon would show that settings have been changed but the job has not been saved.

Clicking in this area will take you to the store page

Clicking in this area will take you to the paper setting page.

Currently selected fold type

  • can be one of the following.

Paper length & Paper Type - input from the paper setting screen.

Fan speed 0 - 1 - 2 or 3 Front & Rear

Long bed option also has centre fan.

Clicking in this area will take you to the Feed bed setting page.

Indicator for status of knives.

K1 & K2 On.

Fold Positions & Micro adjust settings

K1 Off & K2 On

K1 On & K2 Off

Clicking in this area will take you to the Fold setting page.

K1 & K2 Off

Batch quantity - this is input from the batch calculator on the paper setting screen - max. 999

Clicking in this area will take you to the delivery setting page.

Current job count - click to zero

A screen will appear to confirm that you want to

Click to start machine with settings currently shown - you will receive a notification if system switch is not on. Press again to stop Job

SYSTEM

Page 24 of 44

Morgana AutoFold-Pro User Manual, page 25
Text on page 25

Operating the AutoFold Pro

Run Job.

Click to run machine.

System Switch Not On.

Click to confirm System switch is on & then click run button again

The machine running screen will appear.

Click to stop machine.

FOLDING

Page 25 of 44

Morgana AutoFold-Pro User Manual, page 26
Text on page 26

AutoFold Pro

Operating the AutoFold Pro

Setting the machine to operate in manual sheet feed mode

In order to feed heavy stock, very small or very large sheets, embossed or even irregular shaped sheets, it may be necessary to feed the sheets manually.

The machine can be programmed and set up in exactly the same way as explained when operating the machine automatically.

The machine can now be started by activating the System switch to ‘on’.

Select the feed bed.

icon on the touch screen and begin to feed the sheets individually onto the

To stop feeding the sheets, select the System Switch off.

icon on the touch screen and switch the

NOTE. If the delay between feeding sheets is excessive, the system will time out.

SYSTEM

Page 26 of 44

Morgana AutoFold-Pro User Manual, page 27
Text on page 27

Operating the AutoFold Pro

Store Pages.

To get to the Store setting page click the lower tab

status area.

or

from the

New Jobs.

Having set up your job you can give the job a name and save it to a store. You can also retrieve previously saved jobs, modify them or delete jobs you no longer require.

To create a new job name click in text area & keyboard will open to input job name.

Load existing job from store

Clicking to search currently stored jobs

Clicking to delete currently stored jobs

Clicking to save job shown.

Keyboard for entering job name.

Return to Store Menu &

FOLDING

Page 27 of 44

Morgana AutoFold-Pro User Manual, page 28
Text on page 28

DigiFold Pro

Operating the AutoFold Pro

Save confirmation screen.

To confirm saving of job click here.

Search for current jobs to load or modify.

You can search for jobs by clicking the search icon search keyboard for text input.

, this will bring up the

Type in job description or first few characters

To change your mind & return to the previous screen click here.

Jobs matching characters in text box will be shown in this area - selecting job from this area will show job settings in

results & full list of jobs

the right hand status area. Job selected will be shown in text box.

SYSTEM

Press to load job shown in text box.

Page 28 of 44

Morgana AutoFold-Pro User Manual, page 29
Text on page 29

Operating the AutoFold Pro

Loading job confirmation screen.

To cancel loading of Job press here

To confirm loading of Job press here

Loaded job may be modified and then re-saved as the same job name.

Overwrite job confirmation screen.

To cancel overwrite of Job press here.

To confirm overwrite of Job press here

Delete job confirmation screen.

To cancel deletion of Job press here

To confirm deletion of

FOLDING

Page 29 of 44

Morgana AutoFold-Pro User Manual, page 30
Text on page 30

AutoFold Pro

Operating the AutoFold Pro

Tools Menu.

To get to the Tools page click the lower tab

Inch paper in direction of arrow to clear jams

Inch paper in direction of arrow to clear jams

Clicking this icon will show Machine programme revision & Touch Screen software revision.

SYSTEM

Page 30 of 44

Morgana AutoFold-Pro User Manual, page 31
Text on page 31

Removing Paper Jams

In the event of a paper jam occurring, whilst running the machine, follow the steps described below to allow access to remove the jammed paper.

  1. Unlock and lower the delivery unit, open the top cover; see FIG 29.1 below.
  2. If the paper is jammed in the fold rollers; try to rotate the top fold roller, using both hands. Position the thumbs under the tie bar and spread the fingers out above the tie bar.

FIG 29.1

FOLDING

Page 31 of 44

Morgana AutoFold-Pro User Manual, page 32
Text on page 32

AutoFold Pro

Trouble Shooting

Paper fold out of square

Note:- the best fold squareness is achieved when the fold is not on the center of the crease, but to one side or the other.

Check that the fold is to one side of the crease center line.

Check that the roller gaps are not too tight and squashing the crease.

Check that the roller gaps are not too large and allowing the paper to slide (especially so on glossy paper).

Check that the first crease / fold position is not too close to the leading edge of the paper. A minimum distance of 50mm (1.96”) is recommended.

Machine will not start

Check the power supply to the machine.

Check that the emergency stop button has been released.

Check that the top cover is down.

Check that the delivery unit is in the up position, and located correctly, (the machine will not start if the delivery unit is not in its up position).

For heavy stocks, very small or very large sheets, embossed or even irregular stock, it may be necessary to feed the sheets manually - see page 25.

Cracking of the Printed Material along the Crease.

Cracking of the material along the crease may be caused by the following:-

When using dry ink or toner based print engines, the material must be fully acclimatised for at least 48 hours before putting an image onto the paper.

SYSTEM

Page 32 of 44

Morgana AutoFold-Pro User Manual, page 33
Text on page 33

Trouble Shooting

Sheet did not arrive.

If the machine stops and error message 01 is displayed on the touch screen, this indicates that the paper did not arrive at the end of the suck process; so the machine timed out. Press the green tick button and then press the start button.

If the machine stops and error message 02 is displayed on the touch screen, this indicates that a paper jam has been detected. Press the system switch down and then select the right or left arrows, to inch the paper forwards or backwards. See page 30 that describes how to remove paper jams. Press the green tick button and then press the start button.

Clip 1 NOT clear (Back Sensor)

If the machine stops and error message 09 is displayed on the touch screen, this indicates that the sensor is or was blocked when it should have been clear. i.e. A jam in the paper path or the wrong length of paper has passed through the sensor. To correct - check if paper is present and check that the paper path is clear before restarting. See page 30 that describes how to remove paper jams.

FOLDING

Page 33 of 44

Morgana AutoFold-Pro User Manual, page 34
Text on page 34

AutoFold Pro

Trouble Shooting

Clip 1 NOT Blocked (Back Sensor)

If the machine stops and error message 10 is displayed on the touch screen, this indicates that the sensor did not see the paper at the correct time. i.e. A jam in the paper path. To correct - Check if paper has jammed in the machine prior to the sensor. See page 30 that describes how to remove paper jams.

Clip 2 NOT clear (Top Sensor)

If the machine stops and error message 11 is displayed on the touch screen, this indicates that the sensor is or was blocked when it should have been clear. i.e. A jam in the paper path or the wrong length of paper has passed through the sensor. To correct - check if paper is present and check that the paper path is clear before restarting. See page 30 that describes how to remove paper jams.

Clip 2 NOT Blocked (Top Sensor)

If the machine stops and error message 12 is displayed on the touch screen, this indicates that the sensor did not see the paper at the correct time. i.e. A jam in the paper path. To correct - Check if paper has jammed in the machine prior to the sensor. See page 30 that describes how to remove paper jams.

SYSTEM

Page 34 of 44

Morgana AutoFold-Pro User Manual, page 35
Text on page 35

Trouble Shooting

If the machine stops and error message 13 is displayed on the touch screen, this indicates that the ‘Lead Edge Sensor’ has seen a sheet subsequent to the first one as being longer. Again this could actually be a longer sheet, OR it could be a sensor problem (if it is a recurring problem). Check that the paper gate has been set correctly.

If the machine stops and error message 45 is displayed on the touch screen, this indicates that the sheets are too close together. The rate of feed of the sheets needs to be slowed down. If the sheets are being fed from an AutoCreaser Pro 33 or an AutoCreaser Pro 50 adjust the speed on the Tools Menu screen to a slower speed.

Recommended weekly operator maintenance

Clean all sensors. Clean in feed rollers and output drive hubs using the cleaning kit supplied (cleaning kit part number 90-018). Remove and clean the blade assembly.

It is recommended that your Machine is fully serviced at least once every six months by a factory trained Service Engineer.

FOLDING

Page 35 of 44

Morgana AutoFold-Pro User Manual, page 36
Text on page 36

AutoFold Pro

BLANK

PAGE

SYSTEM

Page 36 of 44

Morgana AutoFold-Pro User Manual, page 37
Text on page 37

ITEM

PART NUMBER

DISPATCH KIT

QTY

DESCRIPTION

OPERATORS MANUAL - AutoFold Pro

ROLLER CLEANING KIT

POWER CORD C19 UK 16A 2.5m

DIGITAL THICKNESS GAUGE

WRITE-ON SERIAL NO. LABEL

SPECIFICATION LABEL MSL/CE

HEXAGON BALL DRIVER 2mm

HEXAGON BALL DRIVER 2.5mm

BONDUS L WRENCH 4mm

BONDUS L WRENCH 5mm

DISPATCH BOX

FOLDING

Page 37 of 44

Morgana AutoFold-Pro User Manual, page 38
Text on page 38

AutoFold Pro

ITEM

ACCESSORIES AND OPTIONS

PART NUMBER

DESCRIPTION

FEED BED FRAME - LONG TRANSFER BED ASSY - AUTOCREASER 50

ACCESSORIES.... ....May be obtained from your dealer and fitted to your machine using the instructions supplied, or by reading your operators manual.

SYSTEM

OPTIONS.... ....May also be obtained and fitted by your dealer. You should not attempt to fit options as specialist tools and knowledge are required.

Page 38 of 44

Morgana AutoFold-Pro User Manual, page 39
Text on page 39

RECOMMENDED SPARES

PART NO.

DESCRIPTION

Small Stepper Driver - High Power Small Stepper Driver - Low Power Controller PCB Assembly + Chip Fan Control PCB Assembly RS232 Adaptor PCB Assy. Mini ITX Motherboard (Configured) Link - Paper Guide Knife Driver Pin - M8 Lead - Delivery Input Connector Lead - Sensor Lead - Fan Assy. Lead - Fan Assy. Lead - Drive Motor Lead - Fold Knives Motor Lead - Fold Sensor Lead - Gap Set 1 Pot Lead - Gap Set 2 Pot Lead - Gap Set 3 Pot Lead - Blade Position Sensor Lead - Gap Set 3 Pot Lead - Gap Set 2 Pot Lead - Gap Set 1 Pot Power Supply - 24V Power Supply - 48V PSU Assembly - ATX12V - 300W Input Roller Assembly - Upper Input Roller Assembly - Lower Fold Roller Assembly - Fixed Fold Roller Assembly - 1st Fold Roller Assembly - 2nd Fold Roller Assembly - 3rd Edge Sensor Assembly Touch Screen Assembly - 7” Sensor Bar Assembly Sensor Bar Assembly

FOLDING

Page 39 of 44

Morgana AutoFold-Pro User Manual, page 40
Text on page 40

AutoFold Pro

RECOMMENDED SPARES

PART NO.

DESCRIPTION

175-125-01 Connecting Link Assembly - Drive 175-125-02 Connecting Link Assembly - Knife Hubs 182-014-02 Belt - Paper Transport - Medium 182-014-03 Belt Paper Transport - Short 184-03-01 Jam Detector - Emitter 184-03-02 Jam Detector - Receiver 186-02-01 Clip Sensor Assy. - Lower 604-103 Gas Spring - Delivery 604-108 Gas Spring 607-005 Belt - Vacuum Roller 607-045 Multi Beam Coupler 607-182 Timing Belt 180XL 062 607-185 Timing Belt 160XL 062 613-023 Fuse - 3.15A - 20 x 5mm - Fast Blow Ceramic 681-011 Fuse - 315mA - 20 x 5mm Anti-surge - Ceramic 681-019 Fuse - 6.3A - 20 x 5mm - Anti-surge Ceramic 613-351 Micro Switch - Guard 613-365 Emergency Stop Switch - Double Pole 626-008 Anti-Static Bar 626-009 Anti-Static Bar - Female 652-011 Switch - Low Current Coil - Black 75-258 Anti - Static Transformer 76-262 Stepper Motor - Roller Drive 76-258 Stepper Motor - Belt Drive 76-259 Stepper Motor - Roller Position 124-01-27 Lead - Delivery Roller Pot

NOTE..... The items listed above represent parts which are subject to wear, loss, or accidental damage, and is included for your guidance only. Replacement of parts fitted to your machine require specialist knowledge and should therefore be entrusted to your dealer.

SYSTEM

Page 40 of 44

Morgana AutoFold-Pro User Manual, page 41
Text on page 41

MACHINE CALIBRATION HISTORY

Serial Number:-

Date:- Total Count:- Stretch Lead Edge Trim Del. Roller Trim Knife 1 Trim Knife 2 Trim K1 Deflect Trim K2 Deflect Trim

Date:- Total Count:- Stretch Lead Edge Trim Del. Roller Trim Knife 1 Trim Knife 2 Trim K1 Deflect Trim K2 Deflect Trim

Date:- Total Count:- Stretch Lead Edge Trim Del. Roller Trim Knife 1 Trim Knife 2 Trim K1 Deflect Trim K2 Deflect Trim

Date:- Total Count:- Stretch Lead Edge Trim Del. Roller Trim Knife 1 Trim Knife 2 Trim K1 Deflect Trim K2 Deflect Trim

FOLDING

Page 41 of 44

Morgana AutoFold-Pro User Manual, page 42
Text on page 42

AutoFold Pro

FUSE POSITIONS & RATINGS

(POSITION ET CLASSIFICATION DES FUSIBLES)

PSU (12V) (FUSIBLE PSU (12V) F3.15AH 250 (613-023)

PSUs (24V & 48V) (FUSIBLE PSUs (24 V & 48 V) T6.3AH 250 (681-019)

ANTI-STATIC UNIT

(FUSIBLE ANTI-STATIQUE) T315mAH 250 (681-011)

SYSTEM

Page 42 of 44

Morgana AutoFold-Pro User Manual, page 43
Text on page 43

PRODUCT RECYCLING & DISPOSAL

European Union Disposal Information for Commercial Users

Application of this symbol on your equipment is confirmation that you must dispose of this equipment in compliance with agreed national Procedures.

In accordance with European legislation end of life electrical and electronic equipment subject to disposal must be managed within agreed procedures.

Prior to disposal please contact your local dealer or representative for end of life take back information.

Disposal Information for Domestic Users

Application of this symbol on your equipment is confirmation that you should not dispose of the equipment in the normal household waste stream.

In accordance with European legislation, end of life electrical and electronic equipment subject to disposal must be segregated from household waste.

Private households within EU Member States may return used electrical and electronic equipment to designated collection facilities free of charge. Please contact your local disposal authority for information.

In some Member States when you purchase new equipment your local retailer may be required to take back your old equipment free of charge. Please ask your retailer for information.

Other Countries Please contact your local waste authorities and request disposal information.

FOLDING

Page 43 of 44

Morgana AutoFold-Pro User Manual, page 44

Page 44 of 44 ยท End of manual

Quick start

  1. Tilt the feed bed to match the creaser height by loosening the knurled collars on the gas springs, then retighten.
  2. Fit the Transfer Bed Assembly to the AutoCreaser, align the machines and plug its lead into the AutoFold socket.
  3. Turn the Emergency Stop button clockwise to power on and select the green tick only if trained.
  4. On Paper Settings, choose the fold type, paper length (190-900 mm), thickness and batch.
  5. Measure the sheet with a digital caliper, set Gap 1 to that reading, then set Gaps 2 and 3 from the gap set guide. Always come down to a gap value from above.
  6. Set the feed bed fans (0-3) and delivery, then press Run. Set the AutoCreaser to pulse feed, speed 2.

Troubleshooting

ProblemLikely causeFix (from the manual)
Fold out of squareFold on the crease center line, roller gaps too tight or too loose, or first fold too close to the lead edge.Set the fold slightly to one side of the crease center line, correct the roller gaps, and keep the first fold at least 50 mm from the leading edge. Page 32
Machine will not startNo power, emergency stop pressed, top cover open, or delivery unit not in its up position.Check each item; the machine will not start unless the delivery unit is up and located correctly. Page 32
Print cracks along the creaseToner-printed stock not acclimatised, or roller gaps need adjusting.Acclimatise stock for at least 48 hours before printing with dry ink or toner, and adjust the roller gaps. Page 32
Error 01 - sheet did not arrivePaper did not arrive at the end of the suck process.Press the green tick, then press start. Page 33
Error 02 - paper crunchPaper jam detected.Inch the paper out with the Tools arrows or open the delivery unit and top cover to remove it, then press the green tick and start. Page 33
Error 09 - Clip 1 not clearJam in the paper path or wrong paper length past the back sensor.Check for paper and clear the paper path before restarting. Page 33

Frequently asked questions

What sheet sizes can the AutoFold Pro fold?

Up to 600 x 385 mm (24" x 15") and down to 210 x 140 mm, depending on stiffness and fold type. Paper thickness from 0.11 mm to 0.40 mm. See page 5.

How fast is the AutoFold Pro?

About 6,240 A4 sheets per hour folded in half on speed 3, pulsed. See page 5.

How do I set the roller gaps for a gate fold?

Set Gap 1 to the measured sheet thickness (X), Gap 2 to X and Gap 3 to 3X. For example, 0.3 / 0.3 / 0.9. See page 16.

Does it work with the AutoCreaser Pro 50?

Yes, with the optional AutoCreaser 50 Transfer Bed Assembly. The standard transfer bed fits the AutoCreaser 33 and Pro 33. See page 9.

How do I clear a jam in the fold rollers?

Unlock and lower the delivery unit, open the top cover, and rotate the top fold roller with both hands, thumbs under the tie bar. See page 31.